Search NASA⌕ Search

SEARCH · Search NASA

Results for “finite element method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Fabrication, Modeling, and Testing of a Prototype Thermal Energy Storage Containment

Increasing penetration of variable renewable energy resources requires the deployment of energy storage at a range of durations. Long-duration energy storage (LDES) technologies will fulfill the need to firm variable renewable energy resource output year round; lithium-ion batteries are uneconomical at these durations. Thermal energy storage (TES) is one promising technology for LDES applications because of its siting flexibility and ease of scaling. Particle-based TES systems use low-cost solid particles that have higher temperature limits than the molten salts used in traditional concentrated solar power systems. A key component in particle-based TES systems is the containment silo for the high-temperature (>1100 degrees C) particles. This study combined experimental testing and computational modeling methods to design and characterize the performance of a particle containment silo for LDES applications. A laboratory-scale silo prototype was built and validated the congruent transient finite element analysis (FEA) model. The performance of a commercial-scale silo was then characterized using the validated model. The commercial-scale model predicted a storage efficiency above 95% after 5 days of storage with a design storage temperature of 1200 degrees C. Insulation material and concrete temperature limits were considered as well. The validation of the methodology means the FEA model can simulate a range of scenarios for future applications. This work supports the development of a promising LDES technology with implications for grid-scale electrical energy storage, but also for thermal energy storage for industrial process heating applications.

clean energy↗
DOE OSTI2024

Delamination and Buckling Analysis of a Laminated Component in a High-speed Permanent Magnet Motor

High-speed permanent magnet (PM) machines are widely used because of their high-power density and high efficiency. The high rotation speed also inevitably subjects the PMs to high centrifugal load, which might damage them due to their inherent mechanical vulnerability, such as a much lower tensile strength than the compressive strength. To robustly transfer the torque from the magnet to the shaft, the outer diameter of the laminated rotor core is larger than the inner diameter of the rotor frame to ensure tight contact while working at 20,000 rpm. Motor manufacturing requires the shrink-fit method to assemble the rotor frame and rotor core. However, after the shrink-fit assembly, unexpected local delamination and buckling are observed on the rotor core part. Utilizing finite element simulation, we study the internal stress of assembling these two parts at the provided interference. Simulation results indicate the reasons for the delamination and buckling of the rotor core part and provide suggestions for improving the assembly.

Lin, Lianshan↗
DOE OSTI2025

Electromagnetic Modeling of Lattice Structures in Additively Manufactured Electric Machines

Recent advancements in metal additive manufacturing (AM) show great potential to revolutionize the design and manufacturing of electromagnetic components used in the field of electrical engineering. Lattice structures directly printed by AM processes typically offer better structural performance with reduced weight, such as high stiffness, surface area, elongation, energy absorption, and porosity, than the solid counterpart. This paper aims to study the electromagnetic modeling of lattice structures used in additively manufactured magnetic cores or windings for electric machines. Three dimensional (3D) electromagnetic finite element (FE) analysis with high performance computing (HPC) shows the highest fidelity in predicting the electromagnetic performance of designs with lattice structures by preserving complex geometry details. FE-based homogenization methods have also been explored to potentially speed up concept design. A case study based on an additively manufactured axial-flux permanent magnet machine with a Hilbert pattern stator validates the discussed electromagnetic modeling approaches.

Chung, Shi-Uk [ANSYS, Inc.]↗
DOE OSTI2024

Study of a High-speed Outer Rotor Burst Containing Enclosure

The increasing demand for high-speed electric machines in many applications pushes the development of high-power density electric motors. Outer rotor motors, which can be designed with a larger airgap diameter than inner rotor motors for the same overall diameter and, therefore, provide higher torque, distinguish themselves in space-constrained but high torque applications. However, increasing the motor speed and diameter results in significant centrifugal loads for the outer rotor motor due to its higher airgap diameter. Additional attention must be paid at the design stage to consider the extreme situation of possible mechanical failure, such as the sudden burst of the high-speed rotating parts in the motor, and measures must be taken to prevent their damage to other system components in advance. Through the finite element dynamic impact analysis, we studied the damage caused by broken parts on the inner wall of the electric motor housing when the motor rotates at 20,000 RPM. The proposed method is expected to provide reasonable recommendations of the enclosure material and its thickness required to protect other components in the same powertrain system when the high-power density motor fails unexpectedly.

Lin, Lianshan↗
DOE OSTI2025

Macro-level mechanical interlocking: A rapid joining approach for additively manufactured compression molded composite panels

Composite joining typically involves multiple steps, such as drilling and surface treatment, as part of the manufacturing process, which leads to low throughput and long cycle times. In the present study, we demonstrated a macro-level mechanical interlocking (MI) based, rapid joining technique to assemble additively manufactured compression molded (AMCM) panels, enabling the production of parts larger than the mold dimensions. Composite panels made of 20 wt% short carbon fiber reinforced acrylonitrile butadiene styrene (CF/ABS) were joined using MI features of various geometries, namely tree (TR), dovetail (Dov), rectangle 2 (Rect2), and rectangle 1 (Rect1), and their in-plane strength was evaluated. The resultant strength of the tested MI joints reached up to 74 % of the baseline tensile strength (i.e., the ‘no joint’ case). Observations from optical and scanning electron microscopy revealed inadequate polymer diffusion between the adherends, indicating that the joint strength was primarily derived from mechanical interlocking. Additionally, the fracture surfaces exhibited stress-whitening marks, which were characterized using differential scanning calorimetry (DSC). The increase in melting enthalpy suggested local stretching of polymer chains due to MI. Finite element analysis (FEA) indicated that the Rect1 MI feature, which generated the lowest stress concentration, outperformed the others in terms of joint strength, achieving 42 MPa. As a demonstration of the MI joining method, a battery box tray measuring 108 cm × 34 cm using a mold with an effective dimension of 36 cm × 34 cm successfully manufactured, resulting in a part with an area three times larger than the mold. In conclusion, this study presents a promising approach to improving composite joining techniques while minimizing production complexities.

In-plane joining↗
DOE OSTI2024

pvcracks

SAND2024-00922O This software uses electroluminescence images to predict power loss due to cell cracks in photovoltaic modules. The software will incorporate trained variational autoencoder(s) to parameterize cell cracks detected in electroluminescence images of photovoltaic modules and relate cracks to electrical properties; reduced-order models of finite element simulations of electrical behavior of photovoltaic modules under thermomechanical stresses; reduced-order models of stress distributions; inside photovoltaic modules resulting from x-ray topography experiments; and image segmentation and splining methods to analyze x-ray topography measurements of cracked photovoltaic cells. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525.

Hartley, James↗
DOE OSTI2026

Mechanical Characterization of the NIF Ignition Target TMPSA Bonding Flexure

The Thermo-Mechanical Package Sub-Assembly (TMPSA) provides a critical mechanical, thermal, and electrical interface between a silicon arm and a TMP aluminum can in a NIF ignition target. During assembly, sixteen silicon pads are bonded to the aluminum using a fixture that positions the components and applies a repeatable prescribed displacement through a compliant flexure. The flexure converts fixture interference into displacement and reaction force. Because bondline thickness variation must be maintained within +/-4 µm, consistent flexure behavior is important to the assembly process. With a recent string of TMPSAs exhibiting low bond strength, the flexures were inspected. Despite being manufactured to the same specifications, flexures were found to exhibit variation in measured stiffness. Additionally, the measured stiffness values did not always follow the presumed beam mechanics model. This work addresses two questions: whether the bonding fixture is working as intended, and whether the previously made stiffness measurements are accurate representations of the use case. The flexures are analyzed using Euler-Bernoulli beam theory, measured beam dimensions, finite element analysis, and tolerance stack-up calculations. The analysis shows that the fixed-guided beam mechanics model appropriately represents the flexure during TMPSA bonding, but the chisel-tip stiffness measurement method introduces a deformation to the inner ring of the flexure that is not represented during use. The measured stiffness values should therefore be interpreted as test-condition stiffness values rather than direct measurements of operational flexure stiffness. The discrepancy is therefore attributed primarily to the measurement boundary condition rather than to failure of the fixed-guided beam model. Recommendations are provided for GD&T, dimensional inspection, and a representative stiffness testing method to better control bondline variation.

42 ENGINEERING↗
DOE OSTI2026

PDE-constrained high-order mesh optimization

Here, we present a novel framework for PDE-constrained r-adaptivity of high-order meshes. The proposed method formulates mesh movement as an optimization problem, with an objective function defined as a convex combination of a mesh quality metric and a measure of the accuracy of the PDE solution obtained via finite element discretization. The proposed formulation achieves optimized, well-defined high-order meshes by integrating mesh quality control, PDE solution accuracy, and robust gradient regularization. We adopt the Target-Matrix Optimization Paradigm to control geometric properties across the mesh, independent of the PDE of interest. To incorporate the accuracy of the PDE solution, we introduce error measures that control the finite element discretization error. The implicit dependence of these error measures on the mesh nodal positions is accurately captured by adjoint sensitivity analysis. Additionally, a convolution-based gradient regularization strategy is used to ensure stable and effective adaptation of high-order meshes. We demonstrate that the proposed framework can improve mesh quality and reduce the error by up to 10 times for the solution of Poisson and linear elasto-static problems. The approach is general with respect to the dimensionality, the order of the mesh, the types of mesh elements, and can be applied to any PDE that admits well-defined adjoint operators.

Computer science↗
DOE OSTI2024

Near-net shaping of high-density, complex, spatially-tailored ceramics for extreme environments

The purpose of this subcontract is for LLNL to collaborate with the Subcontractor (UCSB) in the areas of binder jet additive manufacturing (BJAM), hot pressing (HP), finite element modeling (FEM), and multi-material sintering studies. LLNL wants to further develop its hot pressing, AM, and modeling capabilities through LLNL’s Early Career Faculty Program. This work will focus on developing a method to hot press complex-shaped ceramic parts through the co-deposition of a structural/functional ceramic and sacrificial mold material in one assembly via multi-material binder jet printing. The method aims to produce dense, near-net shaped parts with applications relevant to a wide variety of fields including aerospace, defense, and energy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Analysis Background & Noise in Stretched Wire Alignment Technique Measurements

The Stretched-Wire Alignment Technique (SWAT) is one method of magnet alignment for linear induction accelerators. The applications of SWAT have been implemented for aligning solenoid magnets on the Scorpius linear induction accelerator which will be sited at the Nevada National Security Site and the Flash X-Ray (FXR) linear induction accelerator at Lawrence Livermore National Laboratory’s Contained Firing Facility. This article describes both systematic (repeatable) and random sources of background and noise as well as practical ways to eliminate or reduce them to acceptable levels. Systematic sources include reflections from wire ends, rapid sag due to ohmic heating of the wire, magnetic materials, and shot rate. Random sources include air currents, vibration of nearby equipment, mechanical stability of test equipment, and the instruments used to measure the wire motion. Mitigations include curve fitting and adaptive noise signal cancellation, and mechanical damping. Finite Element Analysis (FEA) was used to identify and resolve a repeatable wire vibration frequency interfering with the signal resolution. Two stretched wire alignment technique set ups from Sandia National Labs and Lawrence Livermore National Lab have shown background noise sources and ways of mitigating them by either analysis methods or change of mechanical configuration. Conclusions that were drawn included the severe sensitivity of the deflection to even small external interferences of the SWAT wire such that it requires attention to detail in mechanical set up and analysis.

Linear Inductive Accelerator↗
DOE OSTI2024

A mixed formulation of the plane-stress problem to facilitate reuse of constitutive models in finite-element programs

Here, the plane-stress assumption can be challenging to support in a finite element program because it traditionally requires separate implementations of constitutive models than those intended for three-dimensional or two-dimensional plane-strain simulations. As a solution to this issue, this paper presents a method to solve the plane-stress problem using a mixed formulation. In this formulation, the out-of-plane strain is treated as a field variable that is solved for in addition to the standard in-plane displacement variables, in a manner that weakly enforces the condition that the out-of-plane stress is zero. The proposed formulation is non-intrusive, requiring no modifications to the constitutive models in contrast to the conventional plane-stress formulation. The proposed mixed formulation has been benchmarked against analytical solutions and numerical solutions, with good performance and accuracy.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2025

10-th order of accuracy for numerical solution of 3-D elasticity equations for heterogeneous materials on unfitted Cartesian meshes

We have developed the Optimal Local Truncation Error Method (OLTEM) with 10-th order of accuracy on unfitted Cartesian meshes for a system of 3-D elasticity equations with smooth irregular interfaces. 5 x 5 x 5 = 125-point stencils (similar to those for quadratic finite elements) for elastic heterogeneous materials are used for OLTEM. There are no unknowns at the interface points between different materials; the structure of the global discrete equations is the same for homogeneous and heterogeneous materials. The calculation of unknown stencil coefficients is based on the minimization of the local truncation error of the stencil equations and yields the optimal 10-th order of accuracy for OLTEM on unfitted Cartesian meshes, i.e., the increase by 7 orders in accuracy compared to quadratic finite elements on conformal meshes. A new post-processing procedure provides the 9-th order of accuracy for stresses in the 3-D case. Similar to basic computations it uses OLTEM with the 125-point stencils, the interface conditions and the elasticity equations. It was shown that the use of the elasticity equations for post-processing improves the accuracy of 0.1% stresses by 6 orders compared to post-processing without the use of PDEs. At an accuracy of for stresses, OLTEM with the new post-processing procedure reduces the number of degrees of freedom by 360 - 8000 times compared to quadratic finite elements with similar stencils. OLTEM with the 125-point stencils yields even more accurate results than high-order finite elements with much wider stencils. OLTEM provides accurate numerical results for compressible and nearly incompressible materials.

elasticity equations↗
DOE OSTI2025

Microstructure Clones

Background: A material’s microstructure drives its material performance. Contemporary crystal plasticity experiments compare full-field strain measurements of polycrystal specimens to models. Because each specimen is unique, it is impossible to know which features of the observed deformation are deterministic vs statistical; thus, differences between model and experiment may or may not be significant. Objective: This paper introduces the invention of microstructure clones. Microstructure clones are 2D oligocrystal specimens that have nearly identical microstructures to remedy the aforementioned experimental limitations. Having specimens with nearly identical microstructures will allow for multiple destructive tests of a microstructure (either as repeats or intentionally different experiments), an ability to “see the future” by providing insight into how a specimen will deform, variability quantification, and experimental investigations of response to small microstructural changes. Methods: This work introduces microstructure clones. Repeatability of these clones is demonstrated in tensile bars of pure nickel. Local strain measurements from digital image correlation are compared between clone specimens and compared to results from a crystal plasticity finite element model. Results: Two sets of microstructure clones were tested in this study and displayed very consistent deformation responses within each clone set. Small observed differences in deformation invite investigation into microstructure stochasticity and the effect of small microstructural and loading differences. Conclusions: Microstructure clones represent a significant shift in understanding structure–property relationships. This work reshapes experimental crystal plasticity to allow for experiments that control for specific variables, quantification of microstructural stochasticity (and other sources of stochasticity), and opportunities for replicating experiments.

Crystal Plasticity↗
DOE OSTI2026

A Scaling Study for Incompressible Multispecies Solver in Vertex-CFD

Multispecies incompressible flows occur widely in engineering and environmental applications, such as chemical reactors, fuel cells, ocean mixing, and biomedical systems. However, accurately resolving the complex transport and mixing phenomena associated with multiple interacting species remains computationally challenging, especially for large-scale problems. In this study, we present a robust, high-performance computing--enabled multispecies incompressible Navier–Stokes solver integrated within the Vertex-CFD framework. Our solver employs a fully coupled, implicit, finite element--based formulation that accurately captures the advection, diffusion, and interaction of multiple species in incompressible flows by leveraging the Kokkos library for parallel computing to achieve high computational efficiency. For pressure coupling, the entropically damped artificial compressibility method is utilized. We validated the solver against canonical test cases, including multispecies advection, diffusion, and Bateman systems; the results demonstrate second- and third-order spatial accuracy and consistent convergence. Additionally, we demonstrated the strong and weak scaling study results obtained on the leadership-class high-performance computing system, Frontier at Oak Ridge National Laboratory.

Oz, Furkan [ORNL] (ORCID:0000000265831724)↗
DOE OSTI2024

Mechanical properties of freestanding few-layer graphene/boron nitride/polymer heterostacks investigated with local and non-local techniques

van der Waals two-dimensional materials and heterostructures combined with polymer films continue to attract research attention to elucidate their functionality and potential applications. This study presents the fabrication and mechanical testing of 2D material heterostacks, consisting of few-layer boron nitride and graphene heterostructures synthesized via chemical vapor deposition, capped with a polymethyl methacrylate layer and suspended across ∼200 μm wide trenches using a combined wet–dry transfer method. The mechanical characterization of the heterostacks was performed using two independent approaches: (a) non-local testing with a custom-built tensile testing platform and (b) local load–displacement testing employing atomic force microscopy probes, complemented by finite element simulations. Both approaches provided new results, which are in good agreement with each other. Overall, our findings offer new insights into a combined load capacity in complex multi-material two-dimensional systems, and can contribute to advancing micro and nano-scale device designs and implementations.

Lespasio, Marcus↗
DOE OSTI2024

Simplified inelastic constitutive models for ASME Section III, Division 5 design by inelastic analysis

This report describes the development of simplified, universal constitutive model that captures the high temperature monotonic and cyclic behavior of a range of commonly-used high temperature materials. The goal of the work is to provide a simple, universal constitutive model to replace the current bespoke models for Grade 91, 316H, and Alloy 617 included in Nonmandatory Appendix HBB-Z of the ASME Boiler & Pressure Vessel Code, and to extend this model to cover Alloy 800H. We initiated this work in response to feedback from reactor vendors and other Code users requesting simplified models, compared to the current models, that are easier to implement and use in commercial finite element analysis software. This report describes the completion of this effort by developing a model to correct the defects in standard model forms presently used for high temperature material modeling, described in past work, developing and implementing new numerical methods to train this model against test data, and then actually training the model for the four materials. The report provides a complete mathematical description of the model along with the tabulated material coefficients for the four materials. The final step will be to formulate an ASME Code change to introduce the new models into the Code.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Non-Hermitian quantum mechanics approach for extracting and emulating continuum physics based on bound-state-like calculations: Detailed description

Here, this work applies a reduced basis method to study the continuum physics of a finite quantum system—either few or many-body. Specifically, I develop reduced-order models, or emulators, for the underlying inhomogeneous Schrödinger equation and train the emulators against the equation's bound-state-like solutions at complex energies. The emulators rapidly and accurately interpolate and extrapolate the matrix elements of the Hamiltonian resolvent operator (Green's function) across a parameter space that includes both complex energy and other real-valued physical inputs in the Schrödinger equation. The spectra, discretized and compressed as the result of emulation, and the associated resolvent matrix elements (or amplitudes), have the defining characteristics of non-Hermitian quantum mechanics calculations, featuring complex eigenenergies with negative imaginary parts and branch cuts moved below the real axis in the complex energy plane. Therefore, one now has a method that extracts continuum physics from bound-state-like calculations and emulates those extractions in the input parameter space. Building on a prior Letter [Zhang, Phys. Rev. Lett. 135, 242501 (2025)], this article provides the full theoretical details, a comprehensive analysis of the method's performance, and a brief discussion of how it can be coupled with existing continuum approaches to perform emulations in their input parameter spaces.

ab initio calculations↗
DOE OSTI2024

Multiphysics Co-Optimization Design and Analysis of Double-Side Cooled Silicon Carbide-Based Power Module: Preprint

With the rapid growth of Electric Vehicles (EVs) and Hybrid Electric Vehicles (HEVs), much more rigorous design targets have been set for automotive power electronics, including high power density, high reliability, and low cost. Novel power module and inverter technologies based on wide bandgap (WEG) semiconductors have been developed to meet these design targets, while providing optimal power semiconductor operating temperature and promising thermomechanical performance. Compared with conventional cooling techniques which are normally applied only on one side of power module, double-side cooling approach is now believed to be the solution to enable high power density and low thermal resistance of WEG semiconductor-based power electronics. In this work, we develop a three-phase power module that is double-sided cooled using dielectric fluid jet impingement. In each phase, four silicon carbide (SiC) power semiconductors are bonded to copper busbars without electrical insulation layers. A finite element analysis (FEA) model is created for thermal and thermomechanical analysis. Based on FEA modeling results, we select particular dimensions for a parametric study to optimize thermal and mechanical performance. Using a multi-objective genetic algorithm (MOGA)-based optimization method, we have minimized the maximum junction temperature and thermal stresses within the power module. The multiphysics co-optimization approach has enabled an efficient design process of power modules with greatly reduced computational cost, as compared to conventional processes that rely on exhaustive numerical simulations and iterations.

ADVANCED PROPULSION SYSTEMS↗