Search NASA⌕ Search

SEARCH · Search NASA

Results for “high power laser”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Investigation of a passively Q-switched Raman laser at 1176 nm with Nd{sup 3+}:YAG/Cr{sup 4+}:YAG/YAG composite crystal and a coupled cavity

To reduce the thermal lens effect and increase the efficiency, a composite crystal of Nd{sup 3+}:YAG/Cr{sup 4+}:YAG/YAG and a coupled cavity structure were employed in our passively Q-switched YVO{sub 4}-based Raman laser system. Both the simulation and the experiment results showed that the undoped YAG crystal bonded in the end-face of Cr{sup 4+}:YAG crystal can speed up the heat transfer of Cr{sup 4+}:YAG crystal and reduce the temperature difference between its side surfaces and the center significantly, and the coupled cavity structure can improve the laser performance, especially at high pump power. The maximum output power of Raman laser of 0.92 W at 1176 nm was obtained with an optical-to-optical efficiency of 11.51%. The corresponding repetition rate and the pulse width is 53.5 kHz and 3.22 ns, respectively.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

1.5 – 1.6 μm semiconductor lasers with an asymmetric periodic optically coupled waveguide

High-power 1.5 – 1.6-μm semiconductor lasers with an asymmetric periodic optically coupled waveguide are developed and their current – voltage, light – current, and spectral characteristics are experimentally studied. The characteristics of these lasers are compared with the characteristics of traditional lasers based on double separate-confinement heterostructures. It is shown that the developed lasers have lower divergence and almost the same threshold and power characteristics as conventional lasers with Fabry – Perot resonators. The developed lasers with a cavity length of 1.6 mm and a mesa-stripe contact width of 3 μm mounted in a housing 11 mm in diameter have a power no lower than 200 mW at a pump current not exceeding 700 mA with a divergence of 25 – 35° versus 45° typical for conventional lasers. (lasers)

36 MATERIALS SCIENCE↗
DOE OSTI2026

Understanding spectral dependance of laser-induced damage precursors in dielectric materials (Abbreviated report_23-ERD-006)

High peak and average power laser systems are typically limited by the handling fluence of the optical components. In particular, the multilayer dielectric coatings are known to be much lower operational fluence than the more ideal bulk materials. In this project we proposed and succeeded in probing different established classes of damage prone precursors at different wavelengths to understand their fundamental laser damage response as a function of wavelength. This study helped to shed light on the fundamental physics of the non-linear precursors that govern laser damage phenomena for ns-regime pulsed laser damage. In this study, we utilized the onsite coating capabilities (VPL, IBS coating lab) to purposefully generate laser damage-prone precursors in hafnia-based coatings (both single and multi-layer coatings). Specifically, we engineered coatings with craze lines initiated by nodules, generated coatings with our xenon-based coating process to suppress nanobubble formation and generated hafnia coatings under controlled oxygen flow conditions to study hafnia sub-oxides and oxygen flow dependance. In these studies we found that craze lines are rife with precursors that are sensitive to ultra-violet light but not to infrared light; we found that the removal of nanobubbles helps with all wavelengths tested, but is most impactful for ultra-violet light; we also found that ultra-violet laser damage performance of hafnia is closely matched to oxygen flow rate, while the infrared performance may be slightly better at lower flow rates. During this LDRD we also successfully stood up a new laser damage testing capability, namely a wavelength agile damage test station to study the spectral response of known laser-induced damage precursors. This is a unique and important capability for Lawrence Livermore National Lab, allowing us to understand the spectral response of materials under high intensity irradiation and damage. This is a vital tool to understand non-linear optical response at wavelengths that we have previously been unable to test at.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Coherent frequency combs from electrons colliding with a laser pulse

Highly coherent and powerful light sources capable of generating soft x-ray frequency combs are essential for high precision measurements and rigorous tests of fundamental physics. In this work, we derive the analytical conditions required for the emission of coherent radiation from an electron beam colliding with a laser pulse, modeled as a plane wave. These conditions are applied in a series of numerical simulations, where we show that a soft x-ray frequency comb can be produced if the electrons are regularly-spaced and sufficiently monoenergetic. High quality beams of this kind may be produced in the near future from laser-plasma interactions or linear accelerators. Furthermore, we highlight the advantageous role of employing few-cycle laser pulses in relaxing the stringent monoenergeticity requirements for coherent emission. The conditions derived here can also be used to optimize coherent emission in other frequency ranges, such as the terahertz domain.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

High-efficiency solar thermophotovoltaic system using a nanostructure-based selective emitter

Herein, we present the design, fabrication, optimization, and experimental results of a high-efficiency planar solar thermophotovoltaic (STPV) system utilizing a micro-textured absorber and a nanostructure multilayer metal-dielectric coated selective emitter fabricated on a tungsten (W) substrate. Light absorptance of more than 90% was achieved at visible and near-infrared wavelengths using the microtextured absorbing surface. The nanostructure selective emitter consists of two thin-film optical coatings of silicon nitride (Si3N4) and a layer of W in between to increase the surface emissivity in spectral regimes matching the quantum efficiency of the thermophotovoltaic (TPV) cells. Gallium antimonide (GaSb)-based TPV cells are used in our STPV design. The experiment was conducted at different operating temperatures using a high-power continuous wave laser diode stack as a simulated source of concentrated incident radiation. Our experimental setup measured a maximum electrical output power density of 1.71 W/cm 2 at 1676 K STPV temperature, and the overall power conversion efficiency of 8.4% after normalizing the output power density to the emitter area. This is the highest STPV system efficiency reported so far for any experimental STPV device. The incident optical laser power on the absorber side was 131 W. This is equivalent to a solar concentration factor of ~2100, which is within the practical limit and readily achievable with Fresnel lens setup.

14 SOLAR ENERGY↗
DOE OSTI2020

Towards megajoule x-ray lasers via relativistic four-photon cascade in plasma

Here, a theoretically highly efficient mechanism, operating at high laser intensities and powers, is identified for spectral transferring huge laser energies to shorter ultraviolet and x-ray wavelengths. With megajoule laser energies currently available at near-optical wavelengths, this transfer would, in theory, enable megajoule x-ray lasers, a huge advance over the millijoules x-ray pulses produced now. In fact, enabling even kilojoule x-ray lasers would still be a fantastic advance, and a more likely achievable one, considering practical experimental inefficiencies.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Undersizing of aged African biomass burning aerosol by an ultra-high-sensitivity aerosol spectrometer

The ultra-high-sensitivity aerosol spectrometer (UHSAS) differs from most other optical particle spectrometers by using a high-power infrared (IR) laser to detect small particles and reduce the sizing ambiguity due to the non-monotonicity of scattering with particle size. During the NASA ORACLES project (ObseRvations of Aerosols above CLouds and their intEractionS) over the southeast Atlantic Ocean, the UHSAS clearly undersized particles in the biomass burning plume extending from southern Africa. Since the horizontal and vertical extent of the plume was vast, the NASA P-3B research aircraft often flew through a fairly uniform biomass burning plume for periods exceeding 30 min, sufficient time to explore the details of the UHSAS response by selecting single particle sizes with a differential mobility analyzer (DMA) and passing them to the UHSAS. This was essentially an in-flight calibration of the UHSAS using the particles of interest. Two modes of responses appeared. Most particles were undersized by moderate amounts, ranging from not at all for 70 nm aerosols to 15 % for 280 nm particles. Mie scattering calculations show that composition-dependent refractive index of the particles cannot explain the pattern. Heating of brown carbon or tarballs in the beam causing evaporation and shrinking of the particles is the most plausible explanation, though mis-sizing due to non-sphericity cannot be ruled out. A small fraction (10 %–30 %) of the particles were undersized by 25 % to 35 %. Those were apparently the particles containing refractory black carbon. Laboratory calibrations confirm that black carbon is drastically undersized by the UHSAS, because particles heat to their vaporization point and shrink. A simple empirical correction equation was implemented that dramatically improves agreement with DMA distributions between 100 and 500 nm. It raised the median particle diameter by 18 nm, from 163 to 181 nm, during the August 2017 deployment and by smaller amounts during deployments with less intense pollution. Calculated scattering from UHSAS size distributions increased by about 130 %, dramatically improving agreement with scattering measured by nephelometers. The correction is only valid in polluted instances; clean marine boundary layer and free troposphere aerosols behaved more like the calibration spheres. We were unable to directly test the correction between 500 and 1000 nm, though aerodynamic particle sizer (APS) data appear to show that the correction is poor at the largest diameters, which is no surprise as the composition of those particles is likely to be quite different than that of the accumulation mode. This adds to the evidence that UHSAS data must be treated cautiously whenever the aerosol may absorb infrared light. Similar corrections may be required whenever brown carbon aerosol is present.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

US Advanced and Novel Accelerator Beam Test Facilities

Demonstrating the viability of Advanced Accelerator Concepts (AAC) relies on experimental validation. Over the last three decades, the US has maintained a portfolio of advanced and novel accelerator test facilities to support research critical to AAC. The facilities have enabled pioneering developments in a wide variety of beam and accelerator physics, including plasma-wakefeld and structure-wakefeld acceleration. This paper provides an overview of the current portfolio of US facilities possessing charged particle drive beams with high energies, on the order of tens of joules per pulse, or drive lasers with high peak powers, on the order of a petawatt, and are actively conducting AAC research.

Clarke, Christine↗
DOE OSTI2023

Epitaxial growth and characterization of magnesium gallate (MgGa 2 O 4 ) thin films by pulsed laser deposition

To advance high power device application of MgGa 2 O 4 , it is imperative to achieve crystalline epitaxial thin films and to observe its materials’ characteristics within a wide range of growth conditions. However, there is no published work on the growth of this promising ultrawide bandgap material till this day. In this study, we report the crystalline growth of MgGa 2 O 4 thin films on c-plane (006) sapphire substrates using the pulsed laser deposition (PLD) technique in a broad range of temperature and oxygen pressure. The temperature range for this crystalline growth was within the temperature range of 300°C to 700°C and a pressure range of 1x10 -1 to 1x10 -3 Torr. Within this parameter range, the structural, chemical, optical, and surface property of MgGa 2 O 4 thin films have been investigated. Specifically, the acquired XRD patterns confirmed the film growth along the [111] preferential crystal orientation in the lattice. Here, the rocking curve measurement of the prominent (222) plane showed an increasing trend of the crystallinity with growth temperature and pressure. Furthermore, the XRD phi (φ) scan demonstrated the six-fold rotational symmetry of the MgGa 2 O 4 films and the epitaxial relationship of 30° between the film and the sapphire substrate. The XPS spectra confirmed the presence of +2 and +3 oxidation state for Mg and Ga respectively, in the films. The direct bandgap of MgGa 2 O 4 films was obtained ~5.27±0.03 eV by analyzing the UV-Vis absorbance spectra using the Tauc equation. The SEM images exhibited a granular surface morphology of the MgGa 2 O 4 films with an increasing trend in the grain size from low to high temperature and pressure. The refractive index and thickness of these films were in the range of ~1.90±0.02 and ~70±2.0 nm, respectively determined by fitting the spectroscopic ellipsometry data.

36 MATERIALS SCIENCE↗
DOE OSTI2025

High-energy X-ray radiography with apodized petawatt laser beams

We have produced laser wakefield-accelerated electron beams with energies of 2 GeV in Target Area 1 of the ZEUS facility. These electron beams oscillate in the accelerating structure that is produced in the wake of an ultrashort laser pulse (25 fs). These ’betatron’ oscillations result in the emission of a collimated (4 mrad divergence) beam of high-energy X-ray/gamma photons (on the order of several hundred keV). In this work, we demonstrate the capabilities of the ZEUS laser system by showing that apodizing the laser beam in the near field allows for the production of high-quality betatron X-rays for radiography purposes. This demonstrates that a high-power, large-aperture laser beam could be split into multiple parts to drive betatron X-ray sources from multiple angles or temporal delays into a High Energy Density (HED) target to be probed, enabling pump-probe measurements at multiple temporal delays or tomography on a single shot.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

A review of laser materials processing paradigms

Laser-based processing of materials has progressed from traditional applications such as macroscale cutting and welding, to sophisticated techniques, including ultrafast micromachining, additive manufacturing, and surface engineering at micro- and nano-metric scales. Innovations in laser source technology, particularly the advent of high-power and ultrashort-pulse lasers, have expanded the range of processable materials, enabled a plethora of manufacturing applications, and propelled groundbreaking research in optics, photonics, electronics, and biomedical domains. In this article, we provide a concise, yet broad review of the congruent evolution of lasers and materials processing, and highlight seminal developments in the field over the years, combined with a critical assessment of the state of the art. Finally, we also provide an outlook on emerging needs, as well as a roadmap of anticipated developments in laser technologies and materials platforms over the next 50 years.

Lasers↗
DOE OSTI2023

w22_laser_radiography - Laser-Based MeV Radiography

This project seeks to develop novel x-ray sources based on high-power short-pulse lasers with unique advantages, including small spot size, flexible configuration, and tailorable spectra. Kinetic plasma simulations using the VPIC particle in cell code will be performed to support the R&D goals of this project. If successful, this effort will allow LANL to deploy flexible, compact x-ray sources for static tomographic radiography and dynamic multi-axis radiography at our firing sites and facilities such as pRad and U1a. The higher resolution, shorter pulse duration, and tunability of our proposed sources will enable new applications in the weapons program and broader scientific community. This effort advances the LANL FY22 Strategic Investment Plan priority of “[r]adiographic tools for dynamic and static imaging with improved spatial and temporal resolution, sensitivity, and dose.”

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Optimal Spatial Separation of High-Order Harmonics from Infrared Driving Lasers with an Annular Beam in the Overdriven Regime

We study high-order harmonic generation (HHG) with an annularly shaped high-power, high-repetition-rate laser. In this work we investigate how the spatial separation (or divergence) of the incident laser and the generated high-order harmonics depends on the gas pressure when the laser intensity is in the overdriven regime. It is shown that, when the cone size of the incident annular beam is relatively large, the resulting harmonics are highly collimated along the propagation axis and are spatially separated from the incident beam. Under the overdriven condition, dynamic phase matching favors HHG emissions from short-trajectory electrons that are efficiently built up in the second half of the gas medium. We verify that using an annular beam is a simple and effective method for separating the intense incident infrared laser from the generated high harmonics. Such high-flux and low-divergence light pulses are expected to be powerful sources in the laboratory for ultrafast probing of electron dynamics.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Laser damage of crazed electron-beam high-reflectors following infrared and ultraviolet irradiation in the nanosecond pulse regime

Laser damage of optical components can be a limiting factor in scaling the energetics of high-peak and average power laser systems. Specifically for optical coatings, damage under nanosecond pulsed irradiation is initiated by pre-existing defects in the coating layers, including those that cause discontinuities in the structure, like craze lines. Crazing or cracking in a multilayer dielectric optical coating is induced when the overall coating stress is sufficiently tensile, and is an occasionally observed issue when employing more porous deposition techniques like electron-beam evaporation. Here, in this study, electron-beam high-reflectors were fabricated utilizing process parameters that are known to induce crazing based on prior processing history to systematically evaluate the impact of crazing on reflector damage performance for 1064 and 355 nm lasers. The crazing that was observed was apparently nucleated at nodular defects. When the cross-section of these nodules was investigated, it was observed that there were cracks into the fused silica substrate of approximately 5 µm in depth. The craze lines were irradiated with 1064 and 355 nm light at fluences slightly above the onset of damage initiation fluence of the coating. The 1064 nm irradiated sub-apertures exhibit laser damage but with no spatial correlation with the craze line, whereas the 355 nm irradiated area exhibited many damage sites along the craze line. Finite-difference time-domain electric-field simulations were conducted, and ∼2× field amplification in hafnia was observed for the 355 nm wavelength case. The laser damage can be attributed to a slight electric-field intensification coincidental with an area where UV damage-prone precursors are known to occur. The 355 nm laser damage in uncoated fused silica substrates has been previously correlated to initiate through localized UV absorption at the broken silica bonds in the tips of fractures.

Harthcock, Colin [Lawrence Livermore National Labo↗
DOE OSTI2026

Diagnostic x-ray source using electrons produced by a 100 J-class picosecond laser

Many laser-based high-energy-density science (HEDS) facilities have one or more short-pulse (sub- to few-picosecond) laser beams for diagnostics. For the past decade, we have been developing a novel x-ray probing capability using such picosecond lasers interacting with an underdense plasma to produce relativistic electrons. The ultimate goal of these experiments is to demonstrate a new type of x-ray backlighter using the short-pulse ARC laser at the National Ignition Facility (NIF). Before this diagnostic is fielded at the NIF, it is critical to demonstrate the viability and reproducibility of the x-ray source on comparable high-power short-pulse laser systems. We present experiments that were carried out with the OMEGA EP laser at the University of Rochester’s laboratory for laser energetics. In these experiments, high-energy electrons are produced through a combination of the self-modulation instability and direct laser acceleration in an underdense gas jet. These electrons generate directional x-rays with characteristic energies up to several tens of keV as they execute betatron motion in the ion channel, and the inverse Compton scattering process generates even harder x-rays, with characteristic photon energies of 60–240 keV. When implemented on the OMEGA EP laser(s), this x-ray source yields results that are comparable to those obtained recently on the short-pulse Titan laser at the Jupiter Laser Facility at Lawrence Livermore National Laboratory, after accounting for differences in laser energy, peak intensity, focusing f/#, and plasma source. Applications of such an x-ray source for HEDS experiments are discussed.

backlighter↗
DOE OSTI2024

Demonstration of a 1 TW peak power, joule-level ultrashort Tm:YLF laser

Here we report on the demonstration of a diode-pumped, Tm:YLF-based, chirped pulse amplification laser system operating at λ ≈ 1.9 µm that produces amplified pulse energies exceeding 1.5 J using a single 8-pass power amplifier. The amplified pulses are subsequently compressed to sub-300 fs durations by a diffraction grating pair, producing record >1 TW peak power pulses. To the best of our knowledge, this is the highest peak power demonstrated for any solid-state, near-2 µm laser architecture and illustrates the potential of Tm:YLF for the next generation of high-power, diode-pumped ultrashort lasers.

47 OTHER INSTRUMENTATION↗