Search NASA⌕ Search

SEARCH · Search NASA

Results for “higher heating value”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Satellite-observed latent heat release in a tropical cyclone

The latent heat release (LHR) and the distribution of rainfall rate of a tropical cyclone as it grows from a tropical disturbance to a typhoon were determined from Nimbus 5 Electrically Scanning Microwave Radiometer data. The LHR (calculated over a circular area of 4 deg latitude radius) increased during the development and intensification of the storm from a magnitude of 2.7 x 10 to the fourteenth W (in the disturbance stage) to 8.8 x 10 to the fourteenth W (typhoon stage). The latter value corresponds to a mean rainfall rate of 2.0 mm/h. The more intense the cyclone and the greater the LHR, the greater the percentage contribution of the larger rainfall rates to the LHR. As a cyclone intensifies, the higher rainfall rates tend to concentrate toward the center of the circulation.

Adler, R. F.↗

El Chichon aerosols in the stratosphere: Analyses of lidar data and calculations of radiation budget

Lidar observation at Fukuoka has provided over four years the data of ElChichon aerosols in the stratosphere. Analyses of the data show that an enormous amount of volcanic aerosols has continuously decreased since the beginning of 1983 with significant fluctuations. These fluctuations reveal themselves as a seasonal variation of aerosol content with a maximum in winter-spring and a minimum in summer. The vertical structure of the aerosol layer also shows the seasonal variation. Although the height of a peak around 18 km in the vertical profile of scattering ratio show littel variation, the higher second peak appears frequently from late fall and the lower third peak from late winter to late spring just as two and more tropopauses appear in these periods. The mechanism which causes the seasonal variation will be discussed in terms of the transport by the atmoshperic circulation and the removal through the tropopause gap. Radiation budget in the atmosphere was calculated taking into account the large amount of aerosols observed in the early stages of the El Chichon event. The heating rate of the atmosphere is more than 1 K in the bottom region of the stratosphere even in the nighttime. The possible effect of the volcanic aerosols on the other geophysical phenomena will be discussed using the calculated values of the heating rate.

Fujiwara, M.↗

HOST turbine heat transfer subproject overview

The experimental part of the turbine heat transfer subproject consists of six large experiments, which are highlighted in this overview, and three of somewhat more modest scope. One of the initial efforts was the stator airfoil heat transfer program. The non-film cooled and the showerhead film cooled data have already been reported. The gill region film cooling effort is currently underway. The investigation of secondary flows in a 90 deg curved duct, was completed. The first phase examined flows with a relatively thin inlet boundary layer and low free stream turbulence. The second phase studied a thicker inlet boundary layer and higher free stream turbulence. A comparison of analytical and experimental cross flow velocity vectors is shown for the 60 deg plane. Two experiments were also conducted in the high pressure facility. One examined full coverage film cooled vanes, and the other, advanced instrumentation. The other three large experimental efforts were conducted in a rotation reference frame. An experiment to obtain gas path airfoil heat transfer coefficients in the large, low speed turbine was completed. Single-stage data with both high and low-inlet turbulence were taken. The second phase examined a one and one-half stage turbine and focused on the second vane row. Under phase 3 aerodynamic quantities such as interrow time-averaged and rms values of velocity, flow angle, inlet turbulence, and surface pressure distribution were measured.

Gladden, Herbert J.↗

Large Enhancements in the O/N2 Ratio in the Evening Sector of the Winter Hemisphere During Geomagnetic Storms

In this paper, we have looked for enhancements of the O/N2 ratio in data measured by the Dynamics Explorer 2 (DE 2) satellite in the middle latitudes of the winter hemisphere, based on a prediction that was made by the National Center for Atmospheric Research thermosphere/tonosphere general circulation model (NCAR-TIGCM) that such increases occur. The NCAR-TIGCM predicts that these enhancements should be seen throughout the low latitude region and in many middle latitude locations, but that the enhancements in O/N2 are particularly strong in the middle-latitude, evening-to-midnight sector of the winter hemisphere. When this prediction was used to look for these effects in DE 2 NACS (neutral atmosphere composition spectrometer) data, large enhancements in the O/N2 ratio (approx. 50 to 90%) were seen. These enhancements were observed during the main phase of a storm that occurred on November 24, 1982, and were seen in the same region of the winter hemisphere predicted by the NCAR-TIGCM. They are partially the result of the depletion of N2 and, as electron loss is dependent on dissociative recombination at F(sub 2) altitudes, they have implications for electron densities in this area. Parcel trajectories, which have been followed through the NCAR-TIGCM history file for this event, show that large O/N2 enhancements occur in this limited region in the winter hemisphere for two reasons. First, these parcels of air are decelerated by the antisunward edge of the ion convection pattern; individual parcels converge and subsidence occurs. Thus molecular-nitrogen-poor air is brought from higher to lower heights. Because neutral parcels that are found a little poleward of the equatorial edge of the eveningside convection pattern are swept inward toward the center of the auroral oval, the enhancements occur only in a very limited range of latitudes. Second, nitrogen-poor air is transported from regions close to the magnetic pole in the winter hemisphere. During geomagnetic storms, enhanced meridional winds are driven by the increased pressure-gradient force that is associated with intensified Joule heating in the auroral oval. These pressure-driven winds decrease rapidly on the dayside beyond the auroral oval where the parcels originate, limiting the region into which the parcels can be transported. Thus these two processes drive values of O/N2 in a limited region of the winter hemisphere, and reinforce only in the evening sector, causing large changes in this region.

Burns, A. G.↗

Containerless Processing of a Lithium Disilicate Glass

Glasses of Li2O.2SiO2 (LS2) and LS2 doped with 0.001 wt% platinum (LS2 + 0.001 wt% Pt) compositions were melted, cooled and re-heated at controlled rates while levitated (containerless) inside an Electrostatic Levitator (ESL) furnace at NASA Marshall Space Flight Center. The experiments were conducted in vacuum using spherical 2.5 - 3.0 mm diameter glass samples. The measured critical cooling rate for glass formation, Rc, for the LS2 and LS2 + 0.001 wt% Pt glasses processed at ESL were 14 plus or minus 2 C/min and 130 plus or minus 5 C/min, respectively. The values of Rc for the same LS2 and LS2 + 0.001 wt% Pt glasses processed in a container were 62 plus or minus 3 C/min and 162 plus or minus 5 C/min, respectively. The effective activation energy for crystallization, E, for the LS2 glass processed without a container at ESL was higher than that for an identical glass processed in a container. These results suggest that the glass formation tendency for a containerless LS2 melt is significantly increased compared to an identical melt in contact with a container. The absence of heterogeneous nucleation sites that are inherently present in all melts held in containers is believed to be the reason for the increased glass forming tendency of this containerless melt.

Ranasinghe, K. S.↗

The effect of high lift to drag ratio on aerobraking

This work reviews the use of aerodynamic forces to modify the velocity, and therefore, the orbital path of vehicles due to transit through planetary atmospheres, especially when high values of lift can be generated. The concepts of aerobraking and aerocapture are examined, and the limiting factors are discussed. The use of high L/D vehicles, such as hypersonic waveriders, is examined, and the advantages and disadvantages of their use for aerocapture are addressed. This preliminary study of non-optimized aerocapture trajectories suggests that entrance velocities at Mars can be 10 - 12 km/sec for a waverider while sustaining acceptable loads of about 3 - 4 Earth G's over a 3 minute period, diminishing to less than 1 G in about 15 minutes. The entrance velocities are greater than those for a more conventional biconic configuration with similar deceleration loads sustained. The convective heating rate on the waverider, increased due to the higher velocities and sharp leading edges, has an estimated upper bound of 14000 W/sq cm and a corresponding temperature of about 7500 degrees K.

Crouse, Patrick↗

Solar Cycle Variations of Electron Density and Temperature in the Venusian Nightside Ionosphere

The return of periapsis to low altitudes during the Summer and Fall of 1992 provided a unique opportunity for the Pioneer Venus Orbiter (PVO) to make in situ measurements in the Venusian ionosphere at much lower levels of solar activity (F10.7=120) than existed when periapsis was at low altitudes in 1979 and 1980 (F10.7=220). We present the observations of electron density (N(sub e)) and temperature (T(sub e)) made by the Orbiter Electron Temperature Probe (OETP) during the Entry Period. Empirical models of the Ne and Te height variations are presented and compared with similar models based on OETP measurements made at solar maximum. The median Ne at the ionospheric peak (approx. 140 km) was essentially unchanged from its solar maximum value, but the ionosphere was increasingly depleted at higher altitudes, reaching a factor of 7 lower densities at 200 km. T(sub e) was lower by almost a factor of 2 at 140 km but was rather significantly enhanced at higher altitudes; exceeding its solar maximum values by a factor of 1.3 at 200 km and a factor of 2 at 500 km. In general these results support the earlier conclusions that the nightside upper ionosphere is depleted at lower levels of solar activity by a reduction of the nightward ion flow. The lack of N(sub e) variation near the peak (between solar maximum and entry) suggests that nightward ion transport does not play as large a role in the peak formation as does local ion production by energetic particles. The decrease in T(sub e) at low altitudes suggests that the low densities of the upper ionosphere at the time of PVO entry could no longer support the conduction of heat from the dayside ionosphere, thus allowing the lower nightside ionosphere to cool by collisions with ions and neutrals, and by heat conduction to the cooler regions below.

Theis, Robert F.↗

Integration of Product, Package, Process, and Environment: A Food System Optimization

The food systems slated for future NASA missions must meet crew nutritional needs, be acceptable for consumption, and use resources efficiently. Although the current food system of prepackaged, moderately stabilized food items works well for International Space Station (ISS) missions, many of the current space menu items do not maintain acceptability and/or nutritive value beyond 2 years. Longer space missions require that the food system can sustain the crew for 3 to 5 years without replenishment. The task "Integration of Product, Package, Process, and Environment: A Food System Optimization" has the objective of optimizing food-product shelf life for the space-food system through product recipe adjustments, new packaging and processing technologies, and modified storage conditions. Two emergent food processing technologies were examined to identify a pathway to stable, wet-pack foods without the detrimental color and texture effects. Both microwave-assisted thermal sterilization (MATS) and pressure-assisted thermal stabilization (PATS) were evaluated against traditional retort processing to determine if lower heat inputs during processing would produce a product with higher micronutrient quality and longer shelf life. While MATS products did have brighter color and better texture initially, the advantages were not sustained. The non-metallized packaging film used in the process likely provided inadequate oxygen barrier. No difference in vitamin stability was evident between MATS and retort processed foods. Similarly, fruit products produced using PATS showed improved color and texture through 3 years of storage compared to retort fruit, but the vitamin stability was not improved. The final processing study involved freeze drying. Five processing factors were tested in factorial design to assess potential impact of each to the quality of freeze-dried food, including the integrity of the microstructure. The initial freezing rate and primary freeze drying temperature and pressure were linked to final product quality in freeze-dried corn, indicating processing modifications that could lead to improved product shelf life. Storage temperatures and packaging systems were also assessed for the impact to food quality. Reduced temperature storage had inconclusive impact to the progression of rancidity in butter cookies. Frozen storage was detrimental to fruit and vegetable textural attributes but refrigerated storage helped to sustain color and organoleptic ratings for plant-based foods. With regard to packaging systems, the metallized film overwrap significantly decreased the progression of the rancidity of butter cookies as compared to the highest barrier non-metallized film. The inclusion of oxygen scavengers resulted in noticeable moisture gains in butter cookies over time, independent of packaging film systems. Neither emergent processing technology nor the freeze dry optimization resulted in compelling quality differences from current space food provisions such that a five-year shelf life is likely with these processing changes alone. Using a combination of refrigeration and PATS processing is expected to result in organoleptically-acceptable fruit quality for most fruits through five years. The vitamin degradation will be aided somewhat by the cold temperatures but, given the labile nature of vitamin C, a more stable fortification method, such as encapsulation, should also be investigated to ensure vitamin delivery throughout the product life. Similarly, significant improvement to the packaging film used in the MATS processing, optimization of formulation for dielectric properties, vitamin fortification, and reduced temperature storage should be investigated as a hurdle approach to reach a five year shelf life in wet-pack entrees and soups. Baked goods and other environmentally-sensitive spaceflight foods will require an almost impenetrable barrier to protect the foods from oxygen and moisture ingress but scavengers and reduced storage temperature did not improve baked good shelf life and are not recommended at this time for these foods.

Cooper, Maya R.↗

Free-stream turbulence and concave curvature effects on heated, transitional boundary layers

An experimental investigation of the transition process on flat-plate and concave curved-wall boundary layers for various free-stream turbulence levels was performed. Results show that for transition of a flat-plate, the two forms of boundary layer behavior, identified as laminar-like and turbulent-like, cannot be thought of as separate Blasius and fully-turbulent profiles, respectively. Thus, simple transition models in which the desired quantity is assumed to be an average, weighted on intermittency, of the theoretical laminar and fully turbulent values is not expected to be successful. Deviation of the flow identified as laminar-like from theoretical laminar behavior is shown to be due to recovery after the passage of a turbulent spot, while deviation of the flow identified as turbulent-like from the full-turbulent values is thought to be due to incomplete establishment of the fully-turbulent power spectral distribution. Turbulent Prandtl numbers for the transitional flow, computed from measured shear stress, turbulent heat flux and mean velocity and temperature profiles, were less than unity. For the curved-wall case with low free-stream turbulence intensity, the existence of Gortler vortices on the concave wall within both laminar and turbulent flows was established using liquid crystal visualization and spanwise velocity and temperature traverses. Transition was found to occur via a vortex breakdown mode. The vortex wavelength was quite irregular in both the laminar and turbulent flows, but the vortices were stable in time and space. The upwash was found to be more unstable, with higher levels of u' and u'v', and lower skin friction coefficients and shape factors. Turbulent Prandtl numbers, measured using a triple-wire probe, were found to be near unity for all post-transitional profiles, indicating no gross violation of Reynolds analogy. No evidence of streamwise vortices was seen in the high turbulence intensity case.

Kim, J.↗

Study of diamond film growth and properties

The objective was to study diamond film growth and its properties in order to enhance the laser damage threshold of substrate materials. Calculations were performed to evaluate laser induced thermal stress parameter, R(sub T) of diamond. It is found that diamond has several orders of magnitude higher in value for R(sub T) compared to other materials. Thus, the laser induced damage threshold (LIDT) of diamond is much higher. Diamond films were grown using a microwave plasma enhanced chemical vapor deposition (MPECVD) system at various conditions of gas composition, pressure, temperature, and substrate materials. A 0.5 percent CH4 in H2 at 20 torr were ideal conditions for growing of high quality diamond films on substrates maintained at 900 C. The diamond films were polycrystalline which were characterized by scanning electron microscopy (SEM) and Raman scattering spectroscopy. The top surface of the growing film is always rough due to the facets of polycrystalline film while the back surface of the film replicates the substrate surface. An analytical model based on two dimensional periodic heat flow was developed to calculate the effective in-plane (face parallel) diffusivity of a two layer system. The effective diffusivity of diamond/silicon samples was measured using a laser pulse technique. The thermal conductivity of the films was measured to be 13.5 W/cm K, which is better than that of a type Ia natural diamond. Laser induced damage experiments were performed on bare Si substrates, diamond film coated Si, and diamond film windows. Significant improvements in the LIDT were obtained for diamond film coated Si compared to the bare Si.

Albin, Sacharial↗

Impacts of Urbanization in the Coastal Tropical City of San Juan, Puerto Rico

Urban sprawl in tropical locations is rapidly accelerating and it is more evident in islands where a large percentage of the population resides along the coasts. This paper focuses on the analysis of the impacts of land use and land cover for urbanization in the tropical coastal city of San Juan, in the Caribbean island of Puerto Rico. A mesoscale numerical model, the Regional Atmospheric Modeling System (RAMS), is used to study the impacts of land use for urbanization in the environment including specific characteristics of the urban heat island in the San Juan Metropolitan Area (SJMA), one of the most noticeable urban cores of the Caribbean. The research also makes use of the observations obtained during the airborne San Juan Atlas Mission. Surface and rawinsonde data from the mission are used to validate the atmospheric model yielding satisfactory results. Airborne high resolution remote sensing data are used to update the model's surface characteristics in order to obtain a more accurate and detailed configuration of the SJMA and perform a climate impact analysis based on land cover/land use (LCLU) changes. The impact analysis showed that the presence of the urban landscape of San Juan has an impact reflected in higher air temperatures over the area occupied by the city, with positive values of up to 2.5 C, for the simulations that have specified urban LCLU indexes in the model's bottom boundary. One interesting result of the impact analysis was the finding of a precipitation disturbance shown as a difference in total accumulated rainfall between the present urban landscape and with a potential natural vegetation, apparently induced by the presence of the urban area. Results indicate that the urban enhanced cloud formation and precipitation development occur mainly downwind of the city, including the accumulated precipitation. This spatial pattern can be explained by the presence of a larger urbanized area in the southwest sector of the city, and of the approaching northeasterly trade winds. No significant impacts were found in the sea breeze patterns of the city.

Comarazamy, Daniel E.↗

Impacts of Urbanization in the Coastal Tropical City of San Juan, Puerto Rico

Urban sprawl in tropical locations is rapidly accelerating and it is more evident in islands where a large percentage of the population resides along the coasts. This paper focuses on the analysis of the impacts of land use and land cover for urbanization in the tropical coastal city of San Juan, in the Caribbean island of Puerto Rico. A mesoscale numerical model, the Regional Atmospheric Modeling System (RAMS), is used to study the impacts of land use for urbanization in the environment including specific characteristics of the urban heat island in the San Juan Metropolitan Area (SJMA), one of the most noticeable urban cores of the Caribbean. The research also makes use of the observations obtained during the airborne San Juan Atlas Mission. Surface and raw insonde data from the mission are used to validate the atmospheric model yielding satisfactory results. Airborne high resolution remote sensing data are used to update the model's surface characteristics in order to obtain a more accurate and detailed configuration of the SJMA and perform a climate impact analysis based on land cover/land use (LCLU) changes. The impact analysis showed that the presence of the urban landscape of San Juan has an impact reflected in higher air temperatures over the area occupied by the city, with positive values of up to 2.5 degrees C, for the simulations that have specified urban LCLU indexes in the model's bottom boundary. One interesting result of the impact analysis was the finding of a precipitation disturbance shown as a difference in total accumulated rainfall between the present urban landscape and with a potential natural vegetation, apparently induced by the presence of the urban area. Results indicate that the urban-enhanced cloud formation and precipitation development occur mainly downwind of the city, including the accumulated precipitation. This spatial pattern can be explained by the presence of a larger urbanized area in the southwest sector of the city, and of the approaching northeasterly trade winds.

Comarazamy, Daniel E.↗

Spatially and Temporally Resolved Measurements of Velocity in a H2-air Combustion-Heated Supersonic Jet

This paper presents simultaneous measurements at multiple points of two orthogonal components of flow velocity using a single-shot interferometric Rayleigh scattering (IRS) technique. The measurements are performed on a large-scale Mach 1.6 (Mach 5.5 enthalpy) H2-air combustion jet during the 2007 test campaign in the Direct Connect Supersonic Combustion Test facility at NASA Langley Research Center. The measurements are performed simultaneously with CARS (Coherent Anti-stokes Raman Spectroscopy) using a combined CARS-IRS instrument with a common path 9-nanosecond pulsed, injection-seeded, 532-nm Nd:YAG laser probe pulse. The paper summarizes the measurements of velocities along the core of the vitiated air flow as well as two radial profiles. The average velocity measurement near the centerline at the closest point from the nozzle exit compares favorably with the CFD calculations using the VULCAN code. Further downstream, the measured axial velocity shows overall higher values than predicted with a trend of convergence at further distances. Larger discrepancies are shown in the radial profiles.

Bivolaru, Daniel↗

Study of a Solar X-Ray Telescope

The highly structured nature of the outer solar atmosphere seems to be intimately linked to the presence, at the solar surface, of magnetic fields that have been generated inside the Sun and have emerged to the surface. The corona is brightest (and also hottest) at just those locations where the magnetic field has emerged from inside the Sun. Dynamo theory predicts that strong magnetic fields will be generated deep in the solar interior and that bundles or 'ropes' of magnetic flux will float to the surface. When this happens, a magnetically bipolar region will become visible, extending above the surface in a three-dimensional structure. The field lines penetrate through the surface, showing two magnetic poles, and also exhibit a three-dimensional structure above the surface. The structure created by the field emergence is rooted in the (relatively) cool photosphere and extends through the chromosphere and transition region to the corona. Thus, the magnetic field creates a region, called an active region, which contains portions at temperatures from less than 10(exp 4) K to greater than 10(exp 6) K, and is therefore visible at wavelengths from the infrared through x-rays. The locations where the magnetic field leaves and reenters the visible surface are called the 'footpoints' of the coronal structures associated with the magnetic field. The magnetic fields themselves are not directly visible. However, the hot coronal plasma is, for the most part, constrained to follow the direction of the magnetic field lines in the atmosphere. Now, 100 years after the discovery of x-rays by Wilhelm Roentgen in 1896, we can routinely make observations of the solar corona from outside the Earth's atmosphere in this region of the electromagnetic spectrum. As shown by comparing x-ray images with magnetograms, the bright corona over these bipolar magnetic regions consists of closed structures that seem to follow the orientation of the magnetic field. Although we can see down to the photosphere at x-ray wavelengths when observing the disk of the Sun, this part of the solar atmosphere emits so little that far from the peak of its Planck curve it appears dark in x-ray images. This impression of hot plasma following the magnetic field direction is further strengthened by quantitative studies that calculate coronal magnetic field strength and direction based on photospheric measurements and compare them with the observed brightness and location of the x-ray emitting structures. Such comparisons make it clear that, for the most part, the hot plasma conforms to the geometry of the magnetic field and that the coronal brightness is strongly linked to the strength of the magnetic fields which have erupted to the solar surface from the interior. It is also the case that the larger-scale, fainter corona, as well as coronal holes, are strongly influenced by the large-scale solar magnetic field. We may get a small hint of the reason that the coronal plasma outlines the direction of B by examining the thermal conductivity of a hot plasma in the presence of a magnetic field. This quantity has enormously different values in the directions parallel and perpendicular to the field for a coronal temperature of 10(exp 6) K, a particle density of 10(exp 9)/cu cm and a magnetic field strength of 100 G, the conductivity along the field is approximately 13 orders of magnitude greater than that perpendicular to the field. It is therefore not surprising that a parcel of plasma which is locally heated would conduct that heat preferentially in the direction of the field. We also note that the thermal conductivity parallel to the magnetic field increases with temperature T, while the perpendicular conductivity decreases. To the extent that the loop aspect ratio, i.e., the ratio of loop length to loop width, is determined by the thermal conductivity, we would expect that higher temperature loops are longer and thinner than cooler ones. However, if the loop width becomes smaller than the spatial resolution of the observing instrument, this effect will not be directly observable. For organizational purposes, we provide a listing of some scientific objectives for a Solar-B x-ray telescope, arranged in terms of identifiable features in the corona.

Golub, Leon↗

Isotopic Evidence of Long-Lived Volcanism on Io

Jupiter’s moon Io hosts extensive volcanism, driven by tidal heating. The isotopic composition of Io’s inventory of volatile chemical elements, including sulfur and chlorine, reflects its outgassing and mass-loss history and thus records information about its evolution. We used submillimeter observations of Io’s atmosphere to measure sulfur isotopes in gaseous sulfur dioxide and sulfur monoxide, and chlorine isotopes in gaseous sodium chloride and potassium chloride. We find 34S/32S = 0.0595 ± 0.0038 (equivalent to δ34S = +347 ± 86‰), which is highly enriched compared to average Solar System values and indicates that Io has lost 94 to 99% of its available sulfur. Our measurement of 37Cl/35Cl = 0.403 ± 0.028 (δ37Cl = +263 ± 88‰) shows that chlorine is similarly enriched. These results indicate that Io has been volcanically active for most (or all) of its history, with potentially higher outgassing and mass-loss rates at earlier times.

Katherine De Kleer↗

Coordinated analyses of hydrated Kuiper Belt dust

We report on coordinated mineralogical, chemical, and isotopic analyses of hydrated carbon-rich interplanetary dust particles (IDPs). We focus on hydrated IDPs that contain high solar flare track densities consistent with an origin in outer Solar System bodies such as Edgeworth-Kuiper belt objects (EKBOs) [1]. We are searching for evidence of the heavy water reservoir predicted by self-shielding models [2]. The IDPs were embedded in sulfur and microtome thin sections were obtained for Fourier-transform infrared (FTIR), transmission electron microscopy (TEM), and nanoSIMS analyses. The IDPs were only partly microtomed and the remainder was extracted from the sulfur and pressed into In or Au for high precision O isotopic analyses. The hydrated IDPs in this study are compact low-porosity objects with a mineralogy dominated by fine-grained saponite and lesser serpentine, Fe-Ni sulfides, Mg-Fe carbonates, rare crystaline silicates, and abundant organic matter. The C in the IDPs is abundant (typically >4X CI) and occurs as isolated nanoglobules and finely disseminated within the phyllosilicate matrix of the IDPs. TEM analyses of the nanoglobules show O-rich, S-depleted rims with higher carbonyl functionality than their cores. FTIR spectra show strong aliphatic C-H stretches consistent with the presence of short-chain aliphatic hydrocarbons in these IDPs. The oxygen isotopic compositions measured in 6 IDPs all plot within error of the CCAM line [3]. For several of the IDPs we were able to obtain multiple analyses. The ∆^(17)O values range from -23‰ up to +3.4‰ with most analyses clustering above the terrestrial fractionation line. The O isotopic compositions and the high C contents of these IDPs are distinct from known hydrated carbonaceous chondrites. The track-rich hydrated IDPs record parent body aqueous alteration effects through interactions with 16O-poor H2O on a EKBO parent body. The aqueous alteration activity likely resulted from the heat generated by collisional processes among EKBOs given that these objects are believed to have accreted late after the decay of 26Al [4].

Lindsay P. Keller↗

Chemical Evolution of Interstellar Dust into Planetary Materials

Comets are believed to retain some interstellar materials, stored in fairly pristine conditions since-their formation. The composition and properties of cometary dust grains should reflect those of grains in the outer part of the protosolar nebula which, at least in part, were inherited from the presolar molecular cloud. However, infrared emission features in comets differ from their interstellar counterparts. These differences imply processing of interstellar material on its way to incorporation in comets, but C and N appear to be retained. Overall dust evolution from the interstellar medium (ISM) to planetary materials is accompanied by an increase in proportion of complex organics and a decrease in pure carbon phases. The composition of cometary dust grains was measured in situ during fly-by missions to comet Halley in 1986. The mass spectra of about 5000 cometary dust grains with masses of 5 x 10(exp -17) - 5 x 10(exp -12) g provide data about the presence and relative abundances of the major elements H, C, N, O,Na, Mg, Al, Si, S, Cl, K, Ca, Ti, Cr, Fe, Ni. The bulk abundances of major rock-forming elements integrated over all spectra were found to be solar within a factor of 2, while the volatile elements H, C, N, O in dust are depleted in respect to their total cosmic abundances. The abundances of C and N in comet dust are much closer to interstellar than to meteoritic and are higher than those of dust in the diffuse ISM. In dense molecular clouds dust grains are covered by icy mantles, the average composition of which is estimated to be H:C:N:O = 96:14:1:34. Up to 40% of elemental C and O may be sequestered in mantles. If we use this upper limit to add H, C, N and O as icy mantle material to the abundances residing in dust in the diffuse ISM, then the resulting values for H. C, and N match cometary abundances. Thus, ice mantles undergoing chemical evolution on grains in the dense ISM appear to have been transformed into less volatile and more complex organic residues wherein the H, C and N are largely retained and ultimately accreted in cometary dust. The abundance of O is about the same for cometary dust, meteorites and interstellar dust. In all these samples, most of O in a solid phase is bonded to silicates. In dense molecular clouds, the abundance of O in dust+mantles is significantly higher then in cometary dust. This difference may reflect the greater lability of oxygenated species toward astrophysical processing. Laboratory studies show that O-bearing functional groups in organic compounds tend to be relatively easily removed by heating and/or UV and particle irradiation . In Halley's coma, O-containing organic grains, being unstable, were located closest to the nucleus. The decomposition of the organic grain component in the coma provided a significant extended source contribution to O-containing gaseous species such as CO and H2CO.

Fomenkova, M. N.↗

Photoelectric Emission Measurements on the Analogs of Individual Cosmic Dust Grains

The photoelectric emission process is considered to be the dominant mechanism for charging of cosmic dust grains in many astrophysical environments. The grain charge and equilibrium potentials play an important role in the dynamical and physical processes that include heating of the neutral gas in the interstellar medium, coagulation processes in the dust clouds, and levitation and dynamical processes in the interplanetary medium and planetary surfaces and rings. An accurate evaluation of photoelectric emission processes requires knowledge of the photoelectric yields of individual dust grains of astrophysical composition as opposed to the values obtained from measurements on flat surfaces of bulk materials, as it is generally assumed on theoretical considerations that the yields for the small grains are much different from the bulk values. We present laboratory measurements of the photoelectric yields of individual dust grains of silica, olivine, and graphite of approx. 0.09-5 micrometer radii levitated in an electrodynamic balance and illuminated with ultraviolet radiation at 120-160 nm wavelengths. The measured yields are found to be substantially higher than the bulk values given in the literature and indicate a size dependence with larger particles having order-of-magnitude higher values than for submicron-size grains.

Abbas, M. M.↗