Search NASA⌕ Search

SEARCH · Search NASA

Results for “hybrid control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

PV-Diesel Hybrid SCADA Experiment Network Design

The essential features of an experimental network for renewable power system satellite based supervisory, control and data acquisition (SCADA) are communication links, controllers, diagnostic equipment and a hybrid power system. Required components for implementing the network consist of two satellite ground stations, to satellite modems, two 486 PCs, two telephone receivers, two telephone modems, two analog telephone lines, one digital telephone line, a hybrid-power system equipped with controller and a satellite spacecraft. In the technology verification experiment (TVE) conducted by Savannah State University and Florida Solar Energy Center, the renewable energy hybrid system is the Apex-1000 Mini-Hybrid which is equipped with NGC3188 for user interface and remote control and the NGC2010 for monitoring and basic control tasks. This power system is connected to a satellite modem via a smart interface, RS232. Commands are sent to the power system control unit through a control PC designed as PC1. PC1 is thus connected to a satellite model through RS232. A second PC, designated PC2, the diagnostic PC is connected to both satellite modems via separate analog telephone lines for checking modems'health. PC2 is also connected to PC1 via a telephone line. Due to the unavailability of a second ground station for the ACTS, one ground station is used to serve both the sending and receiving functions in this experiment. Signal is sent from the control PC to the Hybrid system at a frequency f(sub 1), different from f(sub 2), the signal from the hybrid system to the control PC. f(sub l) and f(sub 2) are sufficiently separated to avoid interference.

Kalu, Alex↗
NASA NTRS2009

Active Fail-Safe Micro-Array Flow Control for Advanced Embedded Propulsion Systems

The primary objective of this research effort was to develop and analytically demonstrate enhanced first generation active "fail-safe" hybrid flow-control techniques to simultaneously manage the boundary layer on the vehicle fore-body and to control the secondary flow generated within modern serpentine or embedded inlet S-duct configurations. The enhanced first-generation technique focused on both micro-vanes and micro-ramps highly-integrated with micro -jets to provide nonlinear augmentation for the "strength' or effectiveness of highly-integrated flow control systems. The study focused on the micro -jet mass flow ratio (Wjet/Waip) range from 0.10 to 0.30 percent and jet total pressure ratios (Pjet/Po) from 1.0 to 3.0. The engine bleed airflow range under study represents about a 10 fold decrease in micro -jet airflow than previously required. Therefore, by pre-conditioning, or injecting a very small amount of high-pressure jet flow into the vortex generated by the micro-vane and/or micro-ramp, active flow control is achieved and substantial augmentation of the controlling flow is realized.

Anderson, Bernhard H.↗
NASA NTRS2018

A 6U Hybrid Propulsion Module for CUBESATS

A 6U hybrid propulsion module is presented. It is designed to be used as a stage for a 6U CubeSat with a combined wet mass up to 25 kg. Hybrid rocket propulsion is utilized because it is responsive, high performance, capable of multiple burns and safe/non-toxic. Hybrid rockets employ a solid fuel and liquid or gaseous oxidizer. In this case, the fuel is PolyMethyl MethAcrylate and the oxidizer is gaseous oxygen. This propellant combination produces an Isp of greater than 300 seconds. The gaseous oxidizer simplifies the design and is used in dual mode with cold gas thrusters for attitude control. In general, hybrid propulsion is higher performance and higher thrust than conventional options considered for CubeSats (e.g. monopropellants), making it ideal for larger manuevers such as plane changes. The Attitude Control System has been sized to ensure that the CubeSat can be controlled under the thrust loads of the propulsion system. A hybrid rocket motor of this size is currently being tested at the Jet Propulsion Laboratory. Thirty-four successful tests have been completed at JPL with this propellant combination during the last 2.5 years. Current tests include long duration tests (> 95 seconds) and multiple starts (five). These tests and applicability to potential mission requirements will be discussed. Future test plans to move the motor into a vacuum facility to achieve a Technology Readiness Level of 5 by the end of September 2018 will be discussed, and an overview of the proposed TRL 5 to 6 maturity plan will also be presented.

Nakazono, B.↗
NASA NTRS2004

Control System Architectures, Technologies and Concepts for Near Term and Future Human Exploration of Space

Technologies that facilitate the design and control of complex, hybrid, and resource-constrained systems are examined. This paper focuses on design methodologies, and system architectures, not on specific control methods that may be applied to life support subsystems. Honeywell and Boeing have estimated that 60-80Y0 of the effort in developing complex control systems is software development, and only 20-40% is control system development. It has also been shown that large software projects have failure rates of as high as 50-65%. Concepts discussed include the Unified Modeling Language (UML) and design patterns with the goal of creating a self-improving, self-documenting system design process. Successful architectures for control must not only facilitate hardware to software integration, but must also reconcile continuously changing software with much less frequently changing hardware. These architectures rely on software modules or components to facilitate change. Architecting such systems for change leverages the interfaces between these modules or components.

Boulanger, Richard↗
NASA NTRS2002

Using CONFIG for Simulation of Operation of Water Recovery Subsystems for Advanced Control Software Evaluation

A hybrid discrete/continuous simulation tool, CONFIG, has been developed to support evaluation of the operability life support systems. CON FIG simulates operations scenarios in which flows and pressures change continuously while system reconfigurations occur as discrete events. In simulations, intelligent control software can interact dynamically with hardware system models. CONFIG simulations have been used to evaluate control software and intelligent agents for automating life support systems operations. A CON FIG model of an advanced biological water recovery system has been developed to interact with intelligent control software that is being used in a water system test at NASA Johnson Space Center

Malin, Jane T.↗
NASA NTRS1993

Development of an hp-version finite element method for computational optimal control

The purpose of this research effort is to develop a means to use, and to ultimately implement, hp-version finite elements in the numerical solution of optimal control problems. The hybrid MACSYMA/FORTRAN code GENCODE was developed which utilized h-version finite elements to successfully approximate solutions to a wide class of optimal control problems. In that code the means for improvement of the solution was the refinement of the time-discretization mesh. With the extension to hp-version finite elements, the degrees of freedom include both nodal values and extra interior values associated with the unknown states, co-states, and controls, the number of which depends on the order of the shape functions in each element.

Hodges, Dewey H.↗
NASA NTRS1985

Energy efficient transport technology: Program summary and bibliography

The Energy Efficient Transport (EET) Program began in 1976 as an element of the NASA Aircraft Energy Efficiency (ACEE) Program. The EET Program and the results of various applications of advanced aerodynamics and active controls technology (ACT) as applicable to future subsonic transport aircraft are discussed. Advanced aerodynamics research areas included high aspect ratio supercritical wings, winglets, advanced high lift devices, natural laminar flow airfoils, hybrid laminar flow control, nacelle aerodynamic and inertial loads, propulsion/airframe integration (e.g., long duct nacelles) and wing and empennage surface coatings. In depth analytical/trade studies, numerous wind tunnel tests, and several flight tests were conducted. Improved computational methodology was also developed. The active control functions considered were maneuver load control, gust load alleviation, flutter mode control, angle of attack limiting, and pitch augmented stability. Current and advanced active control laws were synthesized and alternative control system architectures were developed and analyzed. Integrated application and fly by wire implementation of the active control functions were design requirements in one major subprogram. Additional EET research included interdisciplinary technology applications, integrated energy management, handling qualities investigations, reliability calculations, and economic evaluations related to fuel savings and cost of ownership of the selected improvements.

Middleton, D. B.↗
NASA NTRSDate not supplied

Alternative Treatment of Crew Wastewater Using a Hybrid Membrane Technology

Environmental Control and Life Support Systems (ECLSS) of future long-duration, deep-space human exploration missions should treat all “waste” streams for recovery and ideally by near closed-loop. Onboard the International Space Station (ISS), the Water Recovery System (WRS) does not treat urine and gray water to recover elements beyond water and utilizes physical-chemical technologies that operate with single-use and hazardous consumables. Urine offers a renewable source of nitrogen and other trace elements that can support sustainable crop production. In response to the lack of flight ready technologies capable of treating urine and gray water for water and nutrient recovery, a Suspended Aerobic Membrane Bioreactor (SAMBR) is under development between the University of South Florida and Kennedy Space Center. SAMBR is optimized for an early planetary base/partial gravity habitat and serves as a hybrid alternative to currently utilized urine treatment technologies and support closing the resource recovery loop. With its ECLSS minded form factor and modular design, SAMBR’s operation can be customized to suit the treatment objectives (i.e., nitrogen conversion) at that time. This proceeding presents preliminary research pertaining to: 1) design challenges in maximizing hydraulic throughput while minimizing mass and volume of the assembly; 2) capabilities for treating high nitrogen waste under steady and non-steady state conditions; and 3) measured performance parameters such chemical oxygen demand (COD), nitrogen conversion, nutrients, turbidity, and system throughput. Future research and development pertaining to further optimization on system safety, reliability, and expanded treatment capabilities will also be presented.

Membrane Filtration↗
NASA NTRS2003

Discrete Abstractions of Hybrid Systems: Verification of Safety and Application to User-Interface Design

Human interaction with a complex control system involves the user, the automation’s discrete mode logic, and the underlying continuous dynamics of the physical system. The user-interface of such systems always displays a reduced set of information about the entire system. Designing interfaces such that all the pertinent information is available and assuring that this information is correct is important for any user-interface, but especially so for safety-critical systems such as automotive systems and autopilots. Here we describe a methodology for the analysis of hybrid control systems that incorporate user interaction, with the goal of assuring that the information provided to the user is correct. That is, the user-interface must contain all information necessary to safely complete a desired procedure or task. We begin with a hybrid system model which incorporates discrete mode logic as well as nonlinear continuous dynamics. Using a hybrid computational tool for reachability, we find the largest region of the state-space in which we can guarantee the state of the system can always remain – this is the safe region of operation. By implementing a controller for safety which arises from this computation, we mathematically guarantee that this safe region is invariant, meaning that the system will always remain within the safe region if the determined controller is used on the boundary of the safe region. Verification within a hybrid framework allows us to account for the continuous dynamics underlying the discrete representations displayed to the user. Using the computed invariant regions as discrete states, we can abstract a discrete event system from this hybrid system with safety restrictions. This abstraction can be used to determine what information must be provided on the display. Furthermore, in cases in which an interface already exists, the abstraction provides the necessary input into existing interface verification methods. We provide two examples: a car traveling through a yellow light at an intersection and an aircraft autopilot in an automatic landing/go-around maneuver. The examples demonstrate the applicability of this methodology to hybrid systems that have operational constraints we can pose in terms of safety. This methodology differs from existing work in hybrid system verification in that we directly account for the user’s interactions with the system.

Meeko Oishi↗
NASA NTRS1972

The application of optimal control techniques to advanced manned missions, volume 2

The hybrid optimization techique for attitude control design is described in detail. The technque is capable of optimizing an n-dimensional adjustable parameter vector, but a 1-dimensional vector is used as an example to explain the procedure. This permits an easier explanation as opposed to a multidimensional case. The procedure used to derive the perturbation equations of motion describing the 6-DOF shuttle ascent phase is presented. These equations were programmed on the EAI 8800 analog computer to describe the perturbations of the shuttle vehicle from a nominal zero lift trajectory due to wind disturbances. Included are the control system equations, trim equations, and wind angle of attack equations. Analog wiring diagrams, raw data and time-varying coefficients, and state variable responses during shuttle ascent are also considered.

Connor, C. L.↗
NASA NTRS1991

On the integration of reinforcement learning and approximate reasoning for control

The author discusses the importance of strengthening the knowledge representation characteristic of reinforcement learning techniques using methods such as approximate reasoning. The ARIC (approximate reasoning-based intelligent control) architecture is an example of such a hybrid approach in which the fuzzy control rules are modified (fine-tuned) using reinforcement learning. ARIC also demonstrates that it is possible to start with an approximately correct control knowledge base and learn to refine this knowledge through further experience. On the other hand, techniques such as the TD (temporal difference) algorithm and Q-learning establish stronger theoretical foundations for their use in adaptive control and also in stability analysis of hybrid reinforcement learning and approximate reasoning-based controllers.

Berenji, Hamid R.↗
NASA NTRS1975

Automated maintenance for complex hybrid systems

Digital computer, Control Computer Subsystem (CCS), possess high degree of fault tolerance. CCS embodies concepts of self-test and repair. It is capable of monitoring its own performance and of identifying and replacing with standby spare any of its units that fail.

Gilley, G. C.↗
NASA NTRS1991

A hybrid symbolic/finite-element algorithm for solving nonlinear optimal control problems

The general code described is capable of solving difficult nonlinear optimal control problems by using finite elements and a symbolic manipulator. Quick and accurate solutions are obtained with a minimum for user interaction. Since no user programming is required for most problems, there are tremendous savings to be gained in terms of time and money.

Bless, Robert R.↗
NASA NTRS1991

Implementation of a three degree of freedom, motor/brake hybrid force output device for virtual environment control tasks

The advent of high resolution, physical model based computer graphics has left a gap in the design of input/output technology appropriate for interacting with such complex virtual world models. Since virtual worlds consist of physical models, it is appropriate to output the inherent force information necessary for the simulation to the user. The detailed design, construction, and control of a three degree freedom force output joystick will be presented. A novel kinematic design allows all three axes to be uncoupled, so that the system inertia matrix is diagonal. The two planar axes are actuated through an offset gimbal, and the third through a sleeved cable. To compensate for friction and inertia effects, this transmission is controlled by a force feedforward and a closed force feedback proportional loop. Workspace volume is a cone of 512 cubic inches, and the device bandwidth is maximized at 60 Hz for the two planar and 30 Hz for the third axis. Each axis is controlled by a motor/proportional magnetic particle brake combination fixed to the base. The innovative use of motors and brakes allows objects with high resistive torque requirements to be simulated without the stability and related safety issues involved with high torque, energy storing motors alone. Position, velocity, and applied endpoint force are sensed directly. Different control strategies are discussed and implemented, with an emphasis on how virtual environment force information, generated by the MIT Media Lab Computer Graphics and Animation Group BOLIO system, is transmitted to the device controller. The design constraints for a kinesthetic force feedback device can be summarized as: How can the symbiosis between the sense of presence in the virtual environment be maximized without compromising the interaction task under the constraints of the mechanical device limitations? Research in this field will yield insights to the optimal human sensory feedback mix for a wide spectrum of control and interaction problems. A flexible research tool that is designed as an easily reproducible product prototype has been constructed to explore the variety of possible force interaction.

Russo, Massimo↗
NASA NTRS1995

Air pollution control system research: An iterative approach to developing affordable systems

This paper describes a Strategic Environmental Research and Development Program (SERDP) funded project led jointly by the Marine Corps Multi-Commodity Maintenance Centers, and the Air and Energy Engineering Research Laboratory (AEERL) of the USEPA. The research focuses on paint booth exhaust minimization using recirculation, and on volatile organic compound (VOC) oxidation by the modules of a hybrid air pollution control system. The research team is applying bench, pilot and full scale systems to accomplish the goals of reduced cost and improved effectiveness of air treatment systems for paint booth exhaust.

Watt, Lewis C.↗