Search NASA⌕ Search

SEARCH · Search NASA

Results for “hydrogenation process”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Spectroscopic measurement of increases in hydrogen molecular rotational temperature with plasma-facing surface temperature and due to collisional-radiative processes in tokamaks

Abstract Spatially resolved rotational temperature of ground state hydrogen molecules desorbed from plasma-facing surface was measured in QUEST, LTX-β, and DIII-D tokamaks, and the increases of the rotational temperature with the surface temperature and due to collisional-radiative processes in the plasmas were evaluated. The increase due to collisional-radiative processes was calculated by solving rate equations considering electron and proton collisional excitation and deexcitation and spontaneous emission. The calculation results suggest a high sensitivity for the rotational temperature to electron and proton densities, but a negligible sensitivity to the electron, proton, and surface temperatures. In the three tokamaks with different plasma parameters and plasma-facing surface materials, the spatial profile of the rotational temperature was estimated using Fulcher-α emission lines (600–608 nm). In QUEST, the spatial profile of the rotational temperature was estimated from spatially resolved spectra. In the other tokamaks, the rotational temperature was evaluated assuming a single point emission with a location determined from the Fulcher-α emission profile as measured with a filtered camera. In metal-walled devices QUEST and LTX-β, the rotational temperature increased with the surface temperature, and the calculated collisional-radiative increase is consistent with measured increase assuming that the rotational temperature at the surface is approximately 500–600 K higher than the surface temperature. In DIII-D with carbon walls, a larger collisional-radiative increase than the other tokamaks was observed because of the higher density leading to a large difference from the calculated increase compared to the other smaller tokamaks. Measurement of the Fulcher-α emission profile with higher spatial resolution in DIII-D may reduce the difference and reveal the effect of the surface temperature on the rotational temperature. These results show the increases in the rotational temperature with the surface temperature and due to the collisional-radiative processes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

A semi-continuous process for co-production of CO 2 -free hydrogen and carbon nanotubes via methane pyrolysis

Heterogeneous catalytic pyrolysis of hydrocarbons to produce CO 2 -free hydrogen and high-quality solid carbon have historically been stymied by issues related to catalyst deactivation by carbon formed during pyrolysis on the catalyst surface. In addition, a system that demonstrates sustained performance in terms of high conversion, high H 2 yield, and high quality of produced carbon has remained elusive. Here, we propose and demonstrate a semi-continuous methane pyrolysis process to H 2 and carbon nanotubes (CNTs) consisting of repeated pyrolysis and in situ (i.e., within the reactor) CNT dislodging by vigorous steam/argon fluidization. With this process, we demonstrate 10 process cycles with high H 2 yield from CH 4 and CNT dislodging in a fluidized-bed reactor with an Fe/q-Al 2 O 3 catalyst synthesized by an easily scalable incipient wetness impregnation process. We also identify and present opportunities for future catalyst and process development.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Recent advances in polymeric facilitated transport membranes for carbon dioxide separation and hydrogen purification

Membrane and membrane process have been widely considered as one of the best candidates for mitigating CO 2 emissions from the combustion or utilization of fossil fuels. Various amine-containing polymers constitute an important class of membranes, where the highly selective CO 2 transport is achieved by the facilitated transport mechanism. In this review, the amine–CO 2 chemistry is discussed in conjunction with the mechanism of the reaction-mediated CO 2 transport. A wide variety of amine-containing polymers are discussed based on two synthesis motifs: (a) polyamines with amino groups covalently bound to the polymer backbone and (b) small molecule amines embedded in a polymer matrix. This review concludes with the remarks on the facilitated transport membranes for post-combustion carbon capture (CO 2 /N 2 ) and hydrogen purification (CO 2 /H 2 ).

42 ENGINEERING↗
DOE OSTI2021

Direct Numerical Simulation of hydrogen combustion at auto-ignitive conditions: Ignition, stability and turbulent reaction-front velocity

Direct Numerical Simulations (DNS) are performed to investigate the process of spontaneous ignition of hydrogen flames at laminar, turbulent, adiabatic and non-adiabatic conditions. Mixtures of hydrogen and vitiated air at temperatures representing gas-turbine reheat combustion are considered. Adiabatic spontaneous ignition processes are investigated first, providing a quantitative characterization of stable and unstable flames. Results indicate that, in hydrogen reheat combustion, compressibility effects play a key role in flame stability and that unstable ignition and combustion are consistently encountered for reactant temperatures close to the mixture’s characteristic crossover temperature. Furthermore, it is also found that the characterization of the adiabatic processes is also valid in the presence of non-adiabaticity due to wall heat-loss. Finally, a quantitative characterization of the instantaneous fuel consumption rate within the reaction front is obtained and of its ability, at auto-ignitive conditions, to advance against the approaching turbulent flow of the reactants, for a range of different turbulence intensities, temperatures and pressure levels.

42 ENGINEERING↗
DOE OSTI2024

Microstructural Engineering and Accelerated Test Method Development to Achieve Low Cost, High Performance Solutions for Hydrogen Storage and Delivery

This project made advancements in developing lower cost steel alloys with novel microstructural design for use in hydrogen refueling infrastructure such as storage, compressors, and dispensing components, and utilizing accelerated test methods to efficiently evaluate variations in alloy and microstructure design. The project specifically sought to design alloys with lower nickel contents to reduce alloy cost, which was accomplished through substituting manganese for nickel along with other alloy additions to control deformation characteristics known to be important for hydrogen embrittlement resistance. Through Mn substitutions for nickel, austenitic and duplex austenite-ferrite steels were successfully developed with lower cost than currently available commercial stainless steel products that are employed for hydrogen refueling infrastructure. The steels were processed to achieve comparable strength and toughness in hydrogen environments as the commercially available steels containing high Ni contents. To evaluate mechanical performance in hydrogen, a testing methodology was employed to compare ubiquitous laboratory testing using electrochemical hydrogen charging in a liquid electrolyte to less accessible high pressure gaseous testing. While the application of these steels is in high pressure gaseous environments, the electrochemical hydrogen charging tests produced comparable results. Additionally, the Los Alamos Neutron Scatting Center enabled characterization of deformation mechanisms of the steel alloys in the presence of hydrogen, which has been associated with steel alloy characteristics associated with hydrogen embrittlement. Finally, a fracture mechanics based test bed model was developed to predict the influence of hydrogen gas pressure and fatigue conditions on fatigue lifetimes of pressure vessel steels. Together, these developments can be employed to enable lower cost hydrogen fueling infrastructure and more reliable prediction of steel alloy components in hydrogen service conditions. In particular, the newly alloys have the potential to replace stainless steels, having demonstrated comparable performance at substantially reduced cost.

08 HYDROGEN↗
DOE OSTI2024

Detection and Quantitation of Hydrogen Emissions Role and Status of Detection Technology

Hydrogen is a critical strategy to decarbonize energy and manufacturing industries. Hydrogen is nontoxic and can be handled safely, but potential for secondary greenhouse impacts. Hydrogen releases arise from a variety of mechanisms (process, design features, "leaks") that contribute to total hydrogen releases. Detection methodologies will be critical to detect and quantify hydrogen emissions. Detection is to be integrated with advanced analytics (AI) and behavior modelling to effectively identify, quantify, and source locate hydrogen releases. Modelling of emissions will contribute to facility safety and reliability. DOE is committed to develop the tools to model and mitigate the impact of hydrogen releases which include: Support modeling to elucidate released hydrogen degradation; Support the development of tools for emissions quantitation; and Support engineering advancements to minimize hydrogen losses along the value chain (including process, design features, and leaks).

detection↗
DOE OSTI2021

Roundtable on Foundational Science for Carbon-Neutral Hydrogen Technologies (Technology Status Document)

This document summarizes the status of carbon-neutral hydrogen production, storage and transport, and utilization. The state of the art in the implementation, limitations, and challenges of these technologies are summarized. Sources of hydrogen are broadly categorized as hydrcoarbons or water and the processes used to convert these sources to hydrogen as catalytic, thermochemical, or electrochemical. Catalytic steam methane reforming of methane is the dominant process today. Other processes have smaller production volumes and the technology is less mature, but are being deployed at increasing rates, most notably water electrolyzers for hydrogen fueling stations. Efficient transport and storage of hydrogen is one of the major challenges facing a hydrogen-based energy economy. This arises in part from its low volumetric energy density necessitating very high pressures or cryogenic temperatures to store sufficient amounts for practical applications. High-pressure compressed hydrogen cylinders are the incumbent hydrogen storage technology for applications such as light-duty fuel cell electric vehicles, for example. The storage of hydrogen in materials or in chemicals is being pursued to address the issues associated with compression, such as parasitic energy loss and weight, size, and cost of storage containers. The complex nature of the chemical and physical processes involved in the uptake, storage, and release of hydrogen has slowed the discovery of suitable hydrogen storage materials. Both small and large-scale storage face the challenge of embrittlement of the storage media by hydrogen. There is a myriad of uses of hydrogen offering the promises of improving the efficiency of various applications and reducing or eliminating CO 2 emissions. These range from direct electrochemical conversion to electricity to power vehicles and grid-level stationary applications to combustion to production of chemicals and commodities. One of the most impactful applications in terms of reduction of CO 2 emissions is fuel cell passenger vehicles and heavy-duty vehicles such as class 8 trucks. The challenges facing widespread deployment of fuel cells, beyond the major hurdle of the lack of a hydrogen distribution infrastructure, are cost and durability, primarily related to the precious metal cathode catalyst and its durability. The other uses of hydrogen from conversion to hydrocarbons, polymer upcycling, and upgrading of bio-oils are at varying stages of maturity and also face fundamental challenges associated with catalytic processes and materials.

08 HYDROGEN↗
DOE OSTI2023

Microscopic Investigation of H 2 Reduced CuO x /Cu(111) and ZnO/CuO x /Cu(111) Inverse Catalysts: STM, AP-XPS, and DFT Studies

Understanding the reduction mechanism of ZnO/CuO x interfaces by hydrogen is of great importance for advancing the performance of industrial catalysts for CO 2 hydrogenation to methanol. Here, the reduction of pristine and ZnO-modified CuO x /Cu(111) by H 2 was investigated using ambient pressure scanning tunnelling microscopy (AP-STM), ambient pressure X-ray photoelectron spectroscopy (AP-XPS) and density functional theory (DFT). The morphological changes and reaction rates seen for the reduction of CuO x /Cu(111) and ZnO/CuO x /Cu(111) are very different. On CuO x /Cu(111), perfect "44" and "29" structures displayed a very low reactivity towards H 2 at room temperature. A long induction period associated with an autocatalytic process was observed to enable the reduction by the removal of chemisorbed non-lattice oxygen initially and lattice oxygen sequentially at the CuO x -Cu interface, which led to formation of oxygen deficient "5-7" hex and honeycomb structures. In the final stages of the reduction process, regions of residual oxygen species and metallic Cu were seen. The addition of ZnO particles to CuO x /Cu(111) opened new reaction channels. On the ZnO sites, the dissociation of H 2 was fast and H adatoms easily migrated to adjacent regions of copper oxide. This hydrogen spillover substantially enhanced the rate of oxygen removal, resulting in the rapid reduction of the copper oxide located in the periphery of the zinc oxide islands with no signs for the reduction of ZnO. The deposited ZnO completely modified the dynamics for H 2 dissociation and hydrogen migration, providing an excellent source for CO 2 hydrogenation processes on the inverse oxide/metal system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Customization for Current Market Applications of the Carbon Nanotubes Produced by PNNL’s Regenerable Catalytic Pyrolysis (ReCaP) for Scaled Hydrogen Production

Here, we demonstrated the Regenerative Catalytic Pyrolysis (ReCaP) process that generates carbon dioxide-free hydrogen (CO 2 -free H 2 ) from inexpensive and domestically abundant natural gas (NG), while simultaneously producing H 2 at net production cost of $1.0/kg through the sale of valuable carbon nanotube (CNT) co-product. The specific goal of this project is to 1) scale up the production of CNT, 2) correlate the properties of the CNT with the reaction conditions, 3) perform a techno-economic analysis to obtain minimum selling price of H 2 and CNT, and 4) identify industrial partners interested in the CNT co-product.

03 NATURAL GAS↗
DOE OSTI2020

Ammonia Permeation Through Inorganic Membranes

Moisture probes are used in the tritium facility to measure the moisture content of the gas stream. When tritium reacts with nitrogen to form ammonia, the ammonia gas damages the sensitive moisture probe. The gas stream tested during this experiment for moisture probe protection is composed of nitrogen and argon gas in conjunction with ammonia and water vapor. The gas stream is filtered through an inorganic membrane due to the high reactivity of tritium and a residual gas analyzer (RGA) is used to measure the ammonia and water vapor in the gas stream, as well as the permeability of nitrogen and argon through the inorganic membranes. The membranes tested were boron nitride and silver. The permeability was compared for each membrane at different pressures and flow rates. Fourier-transformed infrared spectroscopy (FT-IR) was used to compare the membranes before and after ammonia permeation. Ammonia gas is a byproduct formed from tritium gas reacting with nitrogen in the gas stream, similar to the Haber Process which occurs when hydrogen reacts with nitrogen [2]. The corrosive nature of ammonia damages metals and sensitive instruments such as moisture probes. Moisture probes are essential in various gas and liquid processes for measuring the moisture content of a gas. Membrane research has found that graphene oxide membranes successfully uptake ammonia from the gas stream at a humidity of approximately 30% at which point the pores pin closed, preventing gas permeation. Further research is being conducted to find an inorganic membrane that will prevent ammonia permeation thus circumventing damage to the sensitive moisture probe. The permeation measurements for argon and nitrogen gas and water and ammonia vapor were measured at various pressures of 800, 1000, 1200, 1500, 1800, and 2000 torr. The permeability average (PA) was calculated for each filter using a Barrer calculation. The average permeations for each filter were then compared. The gas composition was measured using the RGA Nitrogen was permeated through the membranes after ammonia permeation and a FT-IR spectrum was obtained. Boron Nitride: As the nitrogen pressure increased, the permeability of the membrane decreased from 800-1200 torr and remained relatively unchanged from 1200-2000 torr. The membrane exhibited a slight decrease in argon permeability from 800-1200 torr and a slight increase from 1500-2000 torr. The boron nitride membrane when permeated with ammonia and nitrogen prevented less ammonia permeation compared to the blank filter. The boron nitride filter demonstrated a decrease in permeability after ammonia permeation. Silver Membrane: When permeated with nitrogen alone, the membrane permeability decreased from 800 torr to 1200 torr. The permeability of the membrane showed little difference as pressure increased from 1200 torr. When permeated with argon, the same phenomenon occurred but on a much smaller scale. When compared to the blank and the boron nitride membranes the silver membrane exhibited significantly lower permeability. This may be in part due to the coating on the silver membrane and differences in pore size of the membranes. During permeation with ammonium hydroxide vapor and nitrogen, the partial pressure of the ammonia increased as compared to the blank membrane. The permeability before and after permeation with ammonia and nitrogen were compared. Permeability values suggested that after being permeated with the ammonia that the permeability for lower pressures increased slightly. There was no significant change in the FT-IR spectrums before and after permeation. Future work: Continue testing various inorganic membranes for ammonia permeation. Further research chemical separation of ammonia from the gas stream, which may prove difficult due to the high reactivity of tritium.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Effect of Hydrogen on Steady-State and Transient Combustion Instability Characteristics

This paper examines the effects of steady-state and transient hydrogen enrichment on thermoacoustic instability in a model gas turbine combustor. Combustion instability, a feedback loop between flame heat release rate oscillations and combustor acoustics, is characterized in a swirl-stabilized flame operated at a range of hydrogen–natural gas fuel blends and heat rates. Measurements of combustor chamber pressure fluctuations and CH* chemiluminescence imaging are used to characterize instability at a range of operating conditions. Steady-state tests show that both mixture heat rate and hydrogen content affect system stability. At a given heat rate, higher levels of hydrogen result in unstable combustion. As heat rate increases, instability occurs at lower concentrations of hydrogen in the fuel. Transient operation was tested in two directions—instability onset and decay—and two hydrogen-addition times—a short time of 1 ms and a longer time of 4 s. Results show that instability onset processes, through the transient addition of hydrogen, are highly repeatable regardless of the timescale of hydrogen addition. Certain instability decay processes are less repeatable, resulting in cases that do not fully transition from unstable to stable combustion despite similar changes in hydrogen fuel flow rate. Flame behavior before, during, and after the transient is characterized using high-speed CH* chemiluminescence imaging. Analysis of the high-speed images shows changes in flame stabilization and dynamics during the onset and decay processes. Finally, the results of this study can have implications for systems that experience variations in fuel composition, particularly in light of growing interest in hydrogen as a renewable fuel.

42 ENGINEERING↗
DOE OSTI2025

Nickel Sulfide-Nanowire-Filled Carbon Nanotubes as an Efficient Overall Water Splitting Electrocatalyst

Pursuing stable, efficient, and cost-effective nanostructured bifunctional electrocatalysts is crucial for advancing the electrochemical water splitting process and enabling clean hydrogen energy production. In recent years, considerable efforts have focused on developing highly efficient and durable commercial electrocatalysts for the oxygen evolution reaction (OER) and overall water splitting (OWS). This research introduces an OWS electrocatalyst-nickel sulfide-filled carbon nanotubes grown on a carbon cloth substrate (Ni 3 S 2 @CNTs/CC), synthesized via a one-step in-situ process. The synergistic integration of metal sulfide (Ni 3 S 2 ) and carbon nanotubes provides abundant active sites for catalytic reactions, ensuring a robust composite nanostructure with enhanced durability. Furthermore, the electrocatalytic performance for OER and OWS has been significantly improved by a simple acid treatment to the electrocatalysts, which introduces physical and chemical defects, particularly oxygen functional groups (the acid-treated sample is termed as Ni 3 S 2 @CNTs/CC-AT). As OER electrocatalysts, Ni 3 S 2 @CNTs/CC and Ni 3 S 2 @CNTs/CC-AT present overpotentials of 304 and 200 mV, respectively, for achieving a current density of 10 mA/cm 2 in the OER process. Furthermore, for complete water splitting in 1.0 M KOH electrolyte, Ni 3 S 2 @CNTs/CC and Ni 3 S 2 @CNTs/CC-AT exhibit potentials of 1.63 and 1.44 V, respectively, to achieve a current density of 10 mA/cm 2 when employed as both anode and cathode. Moreover, Ni 3 S 2 @CNTs/CC and Ni 3 S 2 @CNTs/CC-AT demonstrate durable nature for 22 and 20 h durability in the OER and OWS processes, respectively, offering a promising alternative to ruthenium- and iridium-based electrocatalysts for electrochemical hydrogen production through water splitting. In conclusion, the in-situ synthesis method and acid treatment strategy described in this research are promising approaches to fabricating high-performance encapsulated carbon-nanotube-based electrocatalysts.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Hydrogen from low-density polyethylene via nonthermal plasma: Effects of energy density and process parameters

Nonthermal plasma processes are promising for the modular valorization of plastic waste, especially into hydrogen and carbon materials, due to their high intensity, lack of reliance on catalysts or consumables, and suitability to be directly powered by electricity. We investigate the production of hydrogen from low-density polyethylene (LDPE) as a plastic waste model using streamer Dielectric Barrier Discharge (sDBD) plasma in nitrogen at atmospheric pressure. Here, we examine the effects of process energy density (energy input per unit of feedstock mass), feedstock mass, and plasma intensity (electric voltage) on plasma properties, hydrogen yield and energy efficiency via gas chromatography, optical emission spectroscopy, and electrical diagnostics, together with reactor-scale and nonlinear electric circuit modeling. The characteristic temperature of free electrons in the sDBD plasma is approximately 15000 K (1.3 eV), and that of gas species 10 times lower, demonstrating strong thermal non-equilibrium that can lead to molecular bond scission via charged species impact rather than direct heating. Experimental results show that higher energy density leads to greater hydrogen production and diminishing energy efficiency, and that higher plasma intensity and larger feedstock mass lead to greater hydrogen yield due to higher plasma temperatures and enhanced energy fluxes to the feedstock.

08 HYDROGEN↗
DOE OSTI2020

Oxidation of Glycolate in the Defense Waste Processing Facility (DWPF) Recycle Collection Tank - 20305

The Savannah River Site's Defense Waste Processing Facility (DWPF) operations are being upgraded with the introduction of the Nitric-Glycolic Flowsheet. Glycolic acid has been shown superior to formic acid as the reducing acid used during chemical processing. The new flowsheet improves or maintains necessary parameters such as 1) reduction of mercury, 2) adjustment of feed rheology and 3) adjustment of melter oxidation/reduction potential. Further, the potential for catalytic hydrogen generation in DWPF processing is virtually eliminated. DWPF process condensates are collected and returned to the SRS Concentration, Storage and Transfer Facilities (CSTF). The Recycle Collection Tank (RCT) collects off-gas condensate during chemical processing, vitrification, and other unit operations performed in DWPF and is the singular return vessel delivering recycle effluent back to CSTF. Each batch of recycle may contain a small amount of glycolate from chemical processing and melter off-gas condensates. To avoid potential flammability issues due to thermolysis of glycolate in the CSTF, chemical oxidation within the RCT has been investigated as an option for mitigating the transfer of glycolate. Sodium permanganate has been down-selected as the best option for oxidation of glycolate. Testing was performed using both 2-L and 22-L reactors (16,800:1 and 1,530:1 scale by volume) with non-radioactive waste simulants to approximate the expected RCT compositions. RCT simulants were evaluated at various process pH and temperature conditions. Also, RCT operations, namely the sequence of addition of corrosion inhibitors (NaOH and NaNO{sub 2}) versus a permanganate strike, were evaluated. Glycolate was introduced via a sludge simulant to mimic both expected entrainment and abnormal process foam-over conditions - the range being between 68 and 5100 mg/kg glycolate. Glycolate destruction was monitored by ion chromatography (IC). The corresponding manganese behavior was monitored in real-time using in situ ultraviolet-visible (UV-Vis) spectroscopy. RCT glycolate content can be reduced to below the IC detection limit within 90 minutes for all concentrations investigated. Ion Chromatography analysis revealed that under alkaline conditions, glycolate is primarily oxidized to oxalate with no significant formation of CO{sub 2} or carbonate, and nitrite is not oxidized to nitrate. Initially, complete oxidation of organics species and nitrite was assumed. Determination of the mechanistic chemical reaction has allowed the required amount of permanganate to be more accurately predicted and the total addition to be significantly reduced. UV-Vis measurements reveal that permanganate (Mn{sup 7+}) is reduced to manganate (Mn{sup 6+}) in the RCT. The oxidant stoichiometry is defined by using the initial permanganate to glycolate (P/G) molar ratio. At low initial glycolate concentration (68 and 140 mg/kg), the minimum required initial permanganate to glycolate (P/G) molar ratio was found to be 5-6. With high initial glycolate concentrations (5100 mg/kg) a lower (P/G) molar ratio of ∼2.5 was needed. The final portion of this effort supporting the nitric/glycolic flowsheet will be to test actual (fully radioactive) RCT samples as per the above simulant tests. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Evaluation of Sludge Solids Returns Impacts on Sludge Batch 10 Flammability, Glass Quality, and Glass Processability

The Savannah River National Laboratory (SRNL) is currently preparing to return ≤ 20 kgs of sludge solids collected over time from Tank Farm characterization activities and demonstrations of the Defense Waste Processing Facility (DWPF) flowsheets (nitric-formic and nitric-glycolic). These sludge solids will be transported and added to Tank 51 which is currently preparing Sludge Batch (SB) 10. DWPF plans to operate the under the nitric-glycolic flowsheet for the processing of SB10. The hydrogen generation rate for the nitric-glycolic flowsheet is 0.024 lb h -1 . The addition of ≤20 kg of sludge solids returns to SB 10 does not have an impact on flammability in the DWPF Chemical Process Cell (CPC) or glass quality and processability. The relatively low mass of the addition (≤20 kg) is insufficient to detect a significant analytical change to the expected SB 10 compositions.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Implementing hydrogen oxidation reaction on Pt for controlling counter electrode processes

The search for active, stable, and durable materials for electrochemical energy technologies requires increasing levels of precision to establish true structure-function relationships and guide materials design from atomic and molecular scale. This increases the level of control required over the experimental system for proper materials evaluation. The choice of counter electrode material become crucial, as Pt dissolution at high voltages may cause contamination to the working electrode, especially when studying reductive processes in reactions such as oxygen reduction reaction (ORR), H 2 evolution reaction (HER), and the CO 2 reduction reaction. The learnings from “old school” electrochemistry groups lead us to leverage H 2 reactions over Pt to construct a counter electrode system with controlled potential that eliminates Pt ion contamination concerns. In here we discuss the construction of such Pt|H 2 counter electrode where key experimental aspects such as the H 2 flow rate and effective distribution determines the maximum current this counter electrode can accommodate before switching to high voltage and triggering Pt dissolution. Lastly, we demonstrate the use of the Pt|H 2 counter electrode in aqueous electrolytes during HER occurring on the working electrode at varying currents, showing that the Pt content in the cell remains below parts per trillion (ppt) up to 10 mA, and below 50 ppt at 100 mA up to 1 h of constant current hold. This work provides a guide to the implementation of Pt|H 2 counter electrodes to improve the precision of electrochemical experiments in search of highly active, selective, and durable materials for energy technologies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Quantification of the Impact of Acidified Brine on Fracture-Matrix Transport in a Naturally Fractured Shale Using in Situ Imaging and Modeling

Understanding flow, transport, chemical reactions, and hydromechanical processes in fractured geologic materials is key for optimizing a range of subsurface processes including carbon dioxide and hydrogen storage, unconventional energy resource extraction, and geothermal energy recovery. Flow and transport processes in naturally fractured shale rocks have been challenging to characterize due to experimental complexity and the multiscale nature of quantifying continuum scale descriptions of mass exchange between micrometer-scale fractures and nanometer-scale pores. In this study, we use positron emission tomography (PET) to image the transport of a conservative tracer in a naturally fractured Wolfcamp shale core before and after the core was exposed to low pH brine conditions. Image-based experimental observations are interpreted by fitting an analytical transport model to fracture-containing voxels in the core. Results of this analysis indicate subtle increases in matrix diffusivity and a slightly more uniform fracture velocity distribution following exposure to low pH conditions. These observations are compared with a multicomponent one-dimensional reactive transport model that indicates the capacity for a 10% increase in porosity at the fracture-matrix interface as a result of the low pH brine exposure. This porosity change is the result of the dissolution of carbonate minerals in the shale matrix to low pH conditions. Further, this image-based workflow represents a new approach for quantifying spatially resolved fracture-matrix transport processes and provides a foundation for future work to better understand the role of coupled transport, reaction, and mechanical processes in naturally fractured rocks.

58 GEOSCIENCES↗