Search NASA⌕ Search

SEARCH · Search NASA

Results for “impedence analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Application of finite difference techniques to noise propagation in jet engine ducts

A finite difference formulation is presented for wave propagation in a rectangular two-dimensional duct without steady flow. The difference technique, which should be used in the study of acoustically treated inlet and exhausts ducts used in turbofan engines, can readily handle acoustical flow field complications such as axial variations in wall impedance and cross-section area. In the numerical analysis, the continuous acoustic field is lumped into a series of grid points in which the pressure and velocity at each grid point are separated into real and imaginary terms. An example calculation is also presented for the sound attenuation in a two-dimensional straight soft-walled suppressor.

Baumeister, K. J.↗
NASA NTRS1973

An investigation of the SNS Josephson junction as a three-terminal device

A particular phenomenon of the SNS Josephson junction was investigated; i.e., control by a current entering the normal region and leaving through one of the superconducting regions. The effect of the control current on the junction was found to be dependent upon the ration of the resistances of the two halves of the N layer. A low frequency, lumped, nonlinear model was proposed to describe the electrical characteristics of the device, and a method was developed to plot the dynamic junction resistance as a function of junction current. The effective thermal noise temperature of the sample was determined. Small signal linearized analysis of the device suggests its use as an impedance transformer, although geometric limitations must be overcome. Linear approximation indicates that it is reciprocal and no power gain is possible. It is felt that, with suitable metallurgical and geometrical improvements, the device has promise to become a superconducting transistor.

Meissner, H.↗
NASA NTRS1984

A comparison of lightning and nuclear electromagnetic pulse response of tactical shelters

The internal response (electromagnetic fields and cable responses) of tactical shelters is addressed. Tactical shelters are usually well-shielded systems. Apart from penetrations by signal and power lines, the main leakage paths to the interior are via seams and the environment control unit (ECU) honeycomb filter. The time domain in three-dimensional finite-difference technique is employed to determine the external and internal coupling to a shelter excited by nuclear electromagnetic pulses (NEMP) and attached lightning. The responses of interest are the internal electromagnetic fields and the voltage, current, power, and energy coupled to internal cables. Leakage through the seams and ECU filter is accomplished by their transfer impedances which relate internal electric fields to external current densities. Transfer impedances which were experimentally measured are used in the analysis. The internal numerical results are favorably compared to actual shelter test data under simulated NEMP illumination.

Perala, R. A.↗
NASA NTRS1985

Theoretical efficiency for triplers using nonideal varistor diodes at submillimeter wavelengths

The theoretical efficiency for frequency triplers mutliplying from 300 to 900 GHz has been calculated for nonideal GaAs Schottky diodes operating in the varistor mode. The maximum efficiency is determined to be about 7 percent, only slightly smaller than that for ideal varistors. Guidelines for optimum bias conditions and embedding network impedances have been determined using the large-signal analysis computer program of Siegel and Kerr (1980).

Benson, K.↗
NASA NTRSDate not supplied

Electric Aircraft Propulsion Power System Impedance Modelling Methodology

This paper describes techniques to be used to model megawatt Electrified Aircraft Propulsion (MW EAP) components, specifically motor/generators and inverters, DC-DC converters, and long power leads; resulting in impedance-based models which require no information from the component manufacturers. A custom curve fitting method is described, and an example power supply model is fit using measured impedance data. A method called subscale measurement, employing measurement equipment which has much lower power capability than the MW EAP system under test, is described, simulated, and used to generate an impedance transfer function model of a load. Finally, stability analysis using a Nyquist based approach is performed on the combined supply and load system, using the generated models.

Megawatt electrified aircraft propulsion↗
DOE OSTI2026

Impedance and wakefield studies of the EIC RCS 591 MHz five-cell cavity

The Electron-Ion Collider (EIC) is a next-generation accelerator complex designed to enable high-luminosity collisions between highly polarized electrons and light ions (e.g., He-3). A central component of its Electron Injection System (EIS) is the Rapid Cycling Synchrotron (RCS), which accelerates a single 28 nC electron bunch from 750 MeV to 5, 10, or 18 GeV using an array of 591 MHz five-cell superconducting RF (SRF) cavities—eight at the current design stage. To ensure stable acceleration of high-charge bunches, we conducted detailed impedance and wakefield studies of the SRF cavity structure using both frequency- and time-domain methods. Wakefield solvers (ECHO3D, ECHO1D, CST), eigenmode analysis, and multi-particle tracking with ELEGANT were employed to evaluate longitudinal and transverse impedance effects and to determine instability thresholds. These studies provide critical input for the cavity design and operating parameters required to preserve beam quality and stability in the RCS.

Accelerator Physics↗
DOE OSTI2020

Determining the Length Scale of Transport Impedances in Li-Ion Electrodes: Li(Ni 0.33 Mn 0.33 Co 0.33 )O 2

Battery cathodes are complex multiscale, multifunctional materials. The length scale at which the dominant impedance arises may be difficult to determine even with the most advanced experimental characterization efforts, and thus modeling can play an important role in analysis. Discharge and voltage relaxation curves, interrogated with theory, are used to distinguish between transport impedance that arise on the scale of the active crystal and on the scale of agglomerates (secondary particles) comprised of nanoscale crystals. Model-selection algorithms are applied to determine that the agglomerate scale is dominant in the Li Ni 0.33 Mn 0.33 Co 0.33 O 2 electrode studied here. Furthermore, conditions where the agglomerate and crystal-scale models yield distinct simulation results are demonstrated, providing approaches that can be applied to other systems.

25 ENERGY STORAGE↗
DOE OSTI2021

Manipulating meso-scale solvent structure from Pd nanoparticle deposits in deep eutectic solvents

Deep Eutectic Solvents (DESs) are complex solutions that present unique challenges compared to traditional electrolytes. Unlike most electrolytes and ionic liquids, DESs have delicate hydrogen bond networks that are responsible for their highly sensitive compositional dependence on the melting point. Prior work has demonstrated unique nanoscale structure both experimentally and theoretically that brings both challenges and opportunities to their adoption in traditional electrochemical processes. In this study, we use in-situ sample-rotated ultra-small angle X-ray scattering to resolve the near-interface solvent structure after electrodepositing Pd nanoparticles onto a glassy carbon electrode in choline chloride:urea and choline chloride:ethylene glycol DESs. Our results indicate that solvent structure can be observed on the meso-scale in the choline chloride:urea and choline chloride:ethylene glycol systems. Importantly, this extended solvent structure peaks at -0.5 V (vs. Ag/AgCl) and decreases slightly with higher overpotentials during Pd electrodeposition. Experimentally, the nature of this structure is more pronounced in the ethylene glycol system, as evidenced by both the X-ray scattering as well as the electrochemical impedance spectroscopy (EIS). Here, molecular dynamics simulations and dipolar orientation analysis reveal that chloride delocalization near the Pd interface and long-range interactions between the choline and each hydrogen bond donor are very different and qualitatively consistent with the experimental data. These results show how the long-range solvent-deposit interactions can be tuned by changing the hydrogen bond donor in the DES and the applied potential.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1984

MMIC devices for active phased array antennas

The study of printed circuit discontinuities is necessary in order to design, for example, transitions between rectangular waveguides and printed circuits. New developments with respect to the analytical approaches to this problem are discussed. A summary of the progress in the experimental approach is presented. The accurate solution for the modes in various millimeter-wave waveguides is essential in the analysis of many integrated circuit components, such as filters and impedance transformers. Problems associated with the numerical computation of these modes in two frequently used waveguide forms, namely, the finline and microstrip, are presented. The spectral domain method of formulation, with a moment method solution, is considered. This approach can be readily extended to analyze an arbitrary configuration of dielectric and metallized regions in a shielded enclosure. Galerkin's method is used, where the testing and basic functions are the same. It is shown that the mode functions, or eigenfunctions, are more sensitive to errors than the phase constants, or eigenvalues. The approximate mode functions do not satisfy the orthogonality relationship well, resulting in difficulties when these modal solutions are used to form an approximate Green's function or are used in a mode matching analysis.

Mittra, R.↗
DOE OSTI2025

Correcting impedance measurements for background parasitics to characterize circuit components in cryogenic environments

Predictable circuit response is a critical prerequisite for accurate electronic measurements. Here, we describe a powerful yet straightforward experimental method and analysis model that utilizes an affordable LCR meter in conjunction with an in situ parasitic-impedance background-correction procedure to measure the temperature-dependent impedance (magnitude and phase) of up to ten individual passive circuit elements in a single cryostat run. We show how the model unambiguously identified a ∼20× drop in capacitance for 22 μF 5XR multilayer ceramic capacitors cooled from 300 K to 360 mK in an environment with a parasitic capacitance of ∼300 pF. The same experimental procedure, based on a simple two-wire measurement, was also used to measure 10 and 22 pF thin-film capacitors and 100 MΩ thick-film resistors. The results showed that the resistor values increased by up to an order of magnitude when the devices were cooled from 300 K to 360 mK. Most importantly, we showed that the simple data-acquisition method, coupled with our analysis model, enabled the measurement of component parasitics, and effectively extended the accuracy of a commercial LCR meter beyond its manufacturer-guaranteed values for a wide range of measurement frequencies. We also showed that, in the current configuration, our simple approach is limited to a capacitance accuracy of ∼10 pF.

Carpenter, R. J. [Santa Clara Univ., Santa Clara, ↗
NASA NTRS1991

Wideband finite difference time domain implementation of surface impedance boundary conditions for good conductors

Surface impedance boundary conditions are employed to reduce the solution volume during the analysis of scattering from lossy dielectric objects. In a finite difference solution, they also can be utilized to avoid using small cells, made necessary by shorter wavelengths in conducting media, throughout the solution volume. A 1-D implementation for a surface impedance boundary condition for good conductors in the Finite Difference Time Domain (FDTD) technique.

Beggs, John H.↗
NASA NTRS1997

Fungal degradation of fiber-reinforced composite materials

As described in a previous report, a fungal consortium isolated from degraded polymeric materials was capable of growth on presterilized coupons of five composites, resulting in deep penetration into the interior of all materials within five weeks. Data describing the utilization of composite constituents as nutrients for the microflora are described in this article. Increased microbial growth was observed when composite extract was incubated with the fungal inoculum at ambient temperatures. Scanning electron microscopic observation of carbon fibers incubated with a naturally developed population of microorganisms showed the formation of bacterial biofilms on the fiber surfaces, suggesting possible utilization of the fiber chemical sizing as carbon and energy sources. Electrochemical impedance spectroscopy was used to monitor the phenomena occurring at the fiber-matrix interfaces. Significant differences were observed between inoculated and sterile panels of the composite materials. A progressive decline in impedance was detected in the inoculated panels. Several reaction steps may be involved in the degradation process. Initial ingress of water into the resin matrix appeared to be followed by degradation of fiber surfaces, and separation of fibers from the resin matrix. This investigation suggested that composite materials are susceptible to microbial attack by providing nutrients for growth.

Environmental Microbiology↗
NASA NTRS1991

Finite difference time domain implementation of surface impedance boundary conditions

Surface impedance boundary conditions are employed to reduce the solution volume during the analysis of scattering from lossy dielectric objects. In a finite difference solution, they also can be utilized to avoid using small cells, made necessary by shorter wavelengths in conducting media throughout the solution volume. The standard approach is to approximate the surface impedance over a very small bandwidth by its value at the center frequency, and then use that result in the boundary condition. Two implementations of the surface impedance boundary condition are presented. One implementation is a constant surface impedance boundary condition and the other is a dispersive surface impedance boundary condition that is applicable over a very large frequency bandwidth and over a large range of conductivities. Frequency domain results are presented in one dimension for two conductivity values and are compared with exact results. Scattering width results from an infinite square cylinder are presented as a 2-D demonstration. Extensions to 3-D should be straightforward.

Beggs, John H.↗
NASA NTRS1991

Finite difference time domain implementation of surface impedance boundary conditions

Surface impedance boundary conditions are employed to reduce the solution volume during the analysis of scattering from lossy dielectric objects. In the finite difference solution, they also can be utilized to avoid using small cells, made necessary by shorter wavelengths in conducting media throughout the solution volume. The standard approach is to approximate the surface impedance over a very small bandwidth by its value at the center frequency, and then use that result in the boundary condition. Here, two implementations of the surface impedance boundary condition are presented. One implementation is a constant surface impedance boundary condition and the other is a dispersive surface impedance boundary condition that is applicable over a very large frequency bandwidth and over a large range of conductivities. Frequency domain results are presented in one dimension for two conductivity values and are compared with exact results. Scattering width results from an infinite square cylinder are presented as a two dimensional demonstration. Extensions to three dimensions should be straightforward.

Beggs, John H.↗
DOE OSTI2025

Analysis of Niobium Electropolishing Using a Generalized Distribution of Relaxation Times Method

Using electrochemical impedance spectroscopy, we have devised a method of sensing the microscopic surface conditions on the surface of niobium as it is undergoing an electrochemical polishing (EP) treatment. The method uses electrochemical impedance spectroscopy (EIS) to gather information on the surface state of the electrode without disrupting the polishing reaction. The EIS data is analyzed using a so-called distribution of relaxation times (DRT) method. Using DRT, the EIS data can be deconvolved into discrete relaxation time peaks without any a priori knowledge of the electrode dynamics. By analyzing the relaxation time peaks, we are able to distinguish two distinct modes of the EP reaction. As the polishing voltage is increased, the electrode transitions from the low voltage EP mode, characterized by a single relaxation time peaks, to the high voltage EP mode, characterized by two relaxation time peaks. We theorize that this second peak is caused by the formation of an oxide layer on the electrode. We also find that this oxide induced peak transitions from to a negative relaxation time, which is indicative of a blocking electrode process. By analyzing EPed samples, we show that samples polished in the low voltage mode have significantly higher surface roughness due to grain etching and faceting. We find that the surface roughness of the samples only improves when the oxide film peak is present and in the negative relaxation time region. This shows that EIS combined with DRT analysis can be used to predict etching on EPed Nb. This method can also be performed before or during the EP, which could allow for adjustment of polishing parameters to guarantee a smooth cavity surface finish.

43 PARTICLE ACCELERATORS↗
NASA NTRS1991

Wideband finite difference time domain implementation of surface impedance boundary conditions for good conductors

Surface impedance boundary conditions are used to reduce the solution volume during the analysis of scattering from lossy dielectric objects. In a finite difference solution, they also can be used to avoid using small cells, made necessary by shorter wavelengths in conducting media, throughout the solution volume. A one dimensional implementation is presented for a surface impedance boundary condition for good conductors in the Finite Difference Time Domain (FDTD) technique. In order to illustrate the FDTD surface impedance boundary condition, a planar air-lossy dielectric interface is considered.

Beggs, John H.↗
NASA NTRS2016

Assessment of the Impacts of ACLS on the ISS Life Support System using Dynamic Simulations in V-HAB

The Advanced Closed Loop System (ACLS) is currently under development by Airbus Defense and Space and is slated for launch to the International Space Station (ISS) in 2017. The addition of new hardware into an already complex system such as the ISS life support system (LSS) always poses operational risks. It is therefore important to understand the impacts ACLS will have on the existing systems to ensure smooth operations for the ISS. This analysis can be done by using dynamic computer simulations and one possible tool for such a simulation is Virtual Habitat (V-HAB). Based on Matlab (Registered Trademark) V-HAB has been under development at the Institute of Astronautics of the Technical University Munich (TUM) since 2006 and in the past has been successfully used to simulate the ISS life support systems. The existing V-HAB ISS simulation model treated the interior volume of the space station as one large ideally-stirred container. This model was improved to allow the calculation of the atmospheric composition inside the individual modules of the ISS by splitting it into ten distinct volumes. The virtual volumes are connected by a simulation of the inter-module ventilation flows. This allows for a combined simulation of the LSS hardware and the atmospheric composition aboard the ISS. A dynamic model of ACLS is added to the ISS simulation and different operating modes for both ACLS and the existing ISS life support systems are studied to determine the impacts of ACLS on the rest of the system. The results suggest that the US, Russian and ACLS CO2 systems can operate at the same time without impeding each other. Furthermore, based on the results of this analysis, the US and ACLS Sabatier systems can be operated in parallel as well to achieve the highest possible CO2 recycling together with a low CO2 concentration.

Puetz, Daniel↗