Search NASA⌕ Search

SEARCH · Search NASA

Results for “improved microstructures and properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Effect of Microstructure on Creep in Directionally Solidified NiAl-31Cr-3Mo

The 1200 to 1400 K slow strain rate characteristics of the directionally solidified (DS) eutectic Ni-33Al-31Cr-3 Mo have been determined as a function of growth rate. While differences in the light optical level microstructure were observed in alloys grown at rates ranging from 7.6 to 508 mm/h, compression testing indicated that all had essentially the same strength. The exception was Ni-33 Al-31Cr-3Mo DS at 25.4 mm/h which was slightly stronger than the other growth velocities; no microstructural reason could be found for this improvement. Comparison of the approximately 1300 K properties revealed that four different DS NiAl-34(Cr,Mo) alloys have a similar creep resistance which suggests that there is a common, but yet unknown, strengthening mechanism.

Whittenberger, J. Daniel↗

Effect of Microstructure on Creep in Directionally Solidified NiAl-31Cr-3Mo

The 1200 to 1400 K slow strain rate characteristics of the directionally solidified (DS) eutectic Ni-33Al-31Cr-3 Mo have been determined as a function of growth rate. While differences in the light optical level microstructure were observed in alloys grown at rates ranging from 7.6 to 508 mm/h, compression testing indicated that all had essentially the same strength. The exception was Ni-33Al-31Cr-3Mo DS at 25.4 mm/h which was slightly stronger than the other growth velocities; no microstructural reason could be found for this improvement. Comparison of the approx. 1300 K properties revealed that four different DS NiAl-34(Cr,Mo) alloys have a similar creep resistance which suggests that there is a common, but yet unknown, strengthening mechanism.

Whittenberger, J. D.↗

Improved Rhenium Thrust Chambers

Radiation-cooled bipropellant thrust chambers are being considered for ascent/ descent engines and reaction control systems on various NASA missions and spacecraft, such as the Mars Sample Return and Orion Multi-Purpose Crew Vehicle (MPCV). Currently, iridium (Ir)-lined rhenium (Re) combustion chambers are the state of the art for in-space engines. NASA's Advanced Materials Bipropellant Rocket (AMBR) engine, a 150-lbf Ir-Re chamber produced by Plasma Processes and Aerojet Rocketdyne, recently set a hydrazine specific impulse record of 333.5 seconds. To withstand the high loads during terrestrial launch, Re chambers with improved mechanical properties are needed. Recent electrochemical forming (EL-Form"TM") results have shown considerable promise for improving Re's mechanical properties by producing a multilayered deposit composed of a tailored microstructure (i.e., Engineered Re). The Engineered Re processing techniques were optimized, and detailed characterization and mechanical properties tests were performed. The most promising techniques were selected and used to produce an Engineered Re AMBR-sized combustion chamber for testing at Aerojet Rocketdyne.

O'Dell, John Scott↗

Physics-Based Modeling and Simulation of Self-Reacting Friction Stir Welding Using Computational Fluid Dynamics

A physics-based model was developed to simulate the behavior of material in a self-reacting friction stir welding (SR-FSW) process for the joining of metals. This steady-state model builds upon fundamental computational fluid dynamic (CFD) principles within Ansys Fluent to solve the discretized equations. The effective viscosity is calculated using a viscoplastic model using a Sheppard-Wright formulation of flow stress. Numerous advancements have been made in the incorporated physics including (1) temperature-dependent material properties; (2) locally adaptable flow and thermal boundary conditions; and (3) adapting material properties in nugget in response to microstructural changes. Simulation strategies to accelerate computation and improve numerical stability include adapting the mesh refinement and solver relaxation factors during simulation. The result is a highly robust and computationally efficient model capable of providing the material flow and temperature history across the domain. As material history determines the local microstructure and ultimately weld strength, an accurate and detailed physics-based model has the potential to accelerate SR-FSW process development. The model is highly adaptable to changes in process parameters, tool design, or alloy.

Process Modeling↗

High thermoelectric figure of merit and improved mechanical properties in melt quenched PbTe-Ge and PbTe-Ge{sub 1-x}Si{sub x} eutectic and hypereutectic composites.

We report the synthesis, microstructure, and transport properties of composite thermoelectric materials based on the eutectic phase relationship between PbTe and Ge. When quenched, these eutectic mixtures exhibit considerably stronger mechanical strength and reduced brittleness compared to PbTe itself, while at the same time they possess lower lattice thermal conductivity. Thermal conductivity measurements show values lower than expected based on the law of mixtures and multiphase composites. We find that the thermoelectric performance in these composites can be tuned through the use of hypereutectic compositions and alloying of Ge with Si. PbI{sub 2} was used as an n-type dopant, and precise control of the carrier concentration was achieved to optimize the electrical transport and thermoelectric properties. ZT values approaching 1.3 at 778 K have been obtained in samples of PbTe-Ge{sub 0.8}Si{sub 0.2}(5%), which represent an {approx}62% improvement over that of PbTe.

36 MATERIALS SCIENCE↗

Solid oxide fuel cell electrolytes produced by a combination of suspension plasma spray and very low pressure plasma spray.

Plasma spray coating techniques allow unique control of electrolyte microstructures and properties as well as facilitating deposition on complex surfaces. This can enable significantly improved solid oxide fuel cells (SOFCs), including non-planar designs. SOFCs are promising because they directly convert the oxidization of fuel into electrical energy. However, electrolytes deposited using conventional plasma spray are porous and often greater than 50 microns thick. One solution to form dense, thin electrolytes of ideal composition for SOFCs is to combine suspension plasma spray (SPS) with very low pressure plasma spray (VLPPS). Increased compositional control is achieved due to dissolved dopant compounds in the suspension that are incorporated into the coating during plasma spraying. Thus, it is possible to change the chemistry of the feed stock during deposition. In the work reported, suspensions of sub-micron diameter 8 mol.% Y2O3-ZrO2 (YSZ) powders were sprayed on NiO-YSZ anodes at Sandia National Laboratories (SNL) Thermal Spray Research Laboratory (TSRL). These coatings were compared to the same suspensions doped with scandium nitrate at 3 to 8 mol%. The pressure in the chamber was 2.4 torr and the plasma was formed from a combination of argon and hydrogen gases. The resultant electrolytes were well adhered to the anode substrates and were approximately 10 microns thick. The microstructure of the resultant electrolytes will be reported as well as the electrolyte performance as part of a SOFC system via potentiodynamic testing and impedance spectroscopy.

08 HYDROGEN↗

Microstructure and thermal properties of copper–diamond composites with tungsten carbide coating on diamond particles

An effective method for preparing tungsten carbide coating on diamond surfaces was proposed to improve the interface bonding between diamond and copper. The WC coating was formed on the diamond surfaces with a reaction medium of WO{sub 3} in mixed molten NaCl–KCl salts and the copper–diamond composites were obtained by vacuum pressure infiltration of WC-coated diamond particles with pure copper. The microstructure of interface bonding between diamond and copper was discussed. Thermal conductivity and thermal expansion behavior of the obtained copper–diamond composites were investigated. Results indicated that the thermal conductivity of as-fabricated composite reached 658 W m{sup −} {sup 1} K{sup −} {sup 1}. Significant reduction in coefficient of thermal expansion of the composite compared with that of pure copper was obtained. - Highlights: • WC coating was successfully synthesized on diamond particles in molten salts. • WC coating obviously promoted the wettability of diamond and copper matrix. • WC coating greatly enhanced the thermal conductivity of Cu–diamond composite. • The composites are suitable candidates for heat sink applications.

36 MATERIALS SCIENCE↗

Formation mechanisms of Sn-rich δ phase and its role in strengthening Cu-10Sn manufactured by laser powder bed fusion

Cu-Sn alloys produced via laser powder bed fusion (L-PBF) additive manufacturing (AM) have gained significant attention because they combine the advantages of AM relevant to intricate component design with outstanding combinations of strength, ductility, and resistance to wear and corrosion. However, a detailed understanding of the microstructure that contributes to the enhancement of the mechanical properties of L-PBF Cu-10Sn alloys remains unclear. In particular, there is a lack of understanding of the formation mechanisms of the Sn-rich δ phase commonly observed in Cu-10Sn. This study reveals two distinct variants of the δ phase possessing unique morphological characteristics. These characteristics are attributed to the local solidification conditions inherent to the melt pool boundaries versus those at the interiors of melt pools. A phase transformation pathway that elucidates the origin of the morphological variants of the δ phase from the Sn-rich metastable phases during the cyclic heating of the AM process is proposed. We report superior mechanical properties in L-PBF Cu-10Sn compared to those of conventionally manufactured counterparts due to the synergistic contributions from grain boundaries, dislocations, and the δ phase. Notably, the δ phase alone contributes approximately 22 % to the overall strength observed in the L-PBF Cu-10Sn alloy. The discovery of two types of distinct Sn-rich δ phase offers key insights into precise microstructural control in AM Cu-Sn alloys to enhance mechanical properties, providing practical strategies for improving material performance for diverse applications in automotive, aerospace, and machinery industries.

36 MATERIALS SCIENCE↗

Properties of Extruded PS-212 Type Self-Lubricating Materials

Research has been underway at the NASA Lewis Research Center since the 1960's to develop high temperature, self-lubricating materials. The bulk of the research has been done in-house by a team of researchers from the Materials Division. A series of self-lubricating solid material systems has been developed over the years. One of the most promising is the composite material system referred to as PS-212 or PM-212. This material is a powder metallurgy product composed of metal bonded chromium carbide and two solid lubricating materials known to be self-lubricating over a wide temperature range. NASA feels this material has a wide potential in industrial applications. Simplified processing of this material would enhance its commercial potential. Processing changes have the potential to reduce processing costs, but tribological and physical properties must not be adversely affected. Extrusion processing has been employed in this investigation as a consolidation process for PM-212/PS-212. It has been successful in that high density bars of EX-212 (extruded PM-212) can readily be fabricated. Friction and strength data indicate these properties have been maintained or improved over the P.M. version. A range of extrusion temperatures have been investigated and tensile, friction, wear, and microstructural data have been obtained. Results indicate extrusion temperatures are not critical from a densification standpoint, but other properties are temperature dependent.

Waters, W. J.↗

Novel preparation of Al-5%Cu / BN and Si3N4 composites with analyzing microstructure, thermal and mechanical properties

Highlights: • The novel MMCs Al5Cu-Si{sub 3}N{sub 4}/BN successfully produced by squeeze casting techniques • Squeeze casting technique improves the wettability between the matrix and nitrides. • XRD analysis showing the presence of new AlN and AlB{sub 2} phases • The hardness curves of the MMCs exhibited the increasing trend till reaching peak. • BN reinforcements significantly accelerate precipitation behavior of Al-5%Cu alloy. - Abstract: The purpose of this research is to develop and characterize composites of Al-5%Cu alloy reinforced by silicon and boron nitride (Si{sub 3}N{sub 4}, BN). The developing of this type of composites gives a new trend of metal matrix composite synthesizing, especially in the case of boron nitride. The stir cast composites showed large areas of porosity and agglomeration. On the other hand, the squeezed cast composites exhibited a fairly uniform particles distribution throughout the matrix alloy. The microstructure and XRD results of the composites confirmed a reaction occurred at the interface between the particles and alloy. AlN and AlB{sub 2} phases were identified in Al5%Cu-Si{sub 3}N{sub 4} and Al5%Cu-BN composites respectively. The ageing results showed that the time to reach peak hardness decreased with addition of the particles. Also, the ageing kinetics was significantly accelerated due to the presence of BN particulates. The coefficient of thermal expansion (CTE) results of the matrix alloy and its composites were practically and theoretically determined. Difference between experimental and calculated values of CTE was less than 8%. Increasing the concentration of Si{sub 3}N{sub 4} increased YS from 215 MPa in the matrix alloy to 285 MPa in the Al-5%Cu-7%Si{sub 3}N{sub 4} composites at a testing temperature of 20 °C.

36 MATERIALS SCIENCE↗

Microstructure and heteroatom dictate the doping mechanism and thermoelectric properties of poly(alkyl-chalcogenophenes)

Heteroatom substitution can favorably alter electronic transport in conductive polymers to improve their thermoelectric performance. Here we report the spectroscopic, structural, and thermoelectric properties of poly(3–(3',7'-dimethyloctyl) chalcogenophenes) or P3RX doped with 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4TCNQ), where the heteroatom [X = thiophene (T), selenophene (Se), tellurophene (Te)], the doping methodology, and extent of doping are systematically varied. Spectroscopic measurements reveal that while all P3RX polymers are appreciably doped, the doping mechanism is inherently different. Poly(3-hexylthiophene) (P3HT, used as a control) and poly(3–(3',7'-dimethyloctyl)tellurophene) (P3RTe) are doped primarily via integer charge transfer (ICT), whereas poly(3–(3',7'-dimethyloctyl)selenophene) (P3RSe) and poly(3–(3',7'-dimethyloctyl)thiophene) (P3RT) are doped via charge transfer complex (CTC) mechanisms. Despite these differences, all polymers saturate with roughly the same number of F4TCNQ counterions (1 dopant per 4 to 6 heterocycles), reinforcing the idea that the extent of charge transfer varies with the doping mechanism. Grazing incidence wide-angle x-ray scattering measurements provide insight into the structural driving forces behind different doping mechanisms—P3RT and P3RSe have similar microstructures in which F4TCNQ intercalates between the π-stacked backbones resulting in CTC doping (localized carriers), while P3HT and P3RTe have microstructures in which F4TCNQ intercalates in the alkyl side chain region, giving rise to ICT doping (delocalized carriers). These structural and spectroscopic observations shed light on why P3HT and P3RTe obtain electrical conductivities ca. 3 S/cm, while P3RT and P3RSe have conductivities <10–3 S/cm under the same thin film processing conditions. Ultimately, this work quantifies the effects of heteroatom, microstructural ordering, extent of doping, and doping mechanism, thereby providing rational guidance for designing future thermoelectric polymer-dopant systems.

36 MATERIALS SCIENCE↗

Microstructure and mechanical properties of pure copper wire produced by shear assisted processing and extrusion

Shear assisted processing and extrusion (ShAPE) process can consolidate powdered materials and simultaneously extrude wire or tube with improved properties. We successfully produced copper wire extrusions from powder and solid materials for the first time. The extrusion pressure of ShAPE process is at least two times less than that required for conventional extrusion. We used optical microscopy to inspect and validate the integrity of extrudates. It shows that the microstructure was refined and dynamically recrystallized to equiaxial grains. Compared to the annealed copper wire, ShAPE processed wire has 80% higher yield strength, 15% higher ultimate tensile strength and 20% higher ductility. These were correlated with refined grain size and sub-structuring observed via electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM).

Copper, Wire, Shear Assisted Processing and Extrus↗

Microstructure and properties of Cu-Sn-Zn-TiO 2 nano-composite coatings on mild steel

Cu-Sn-Zn coatings have been widely used in industry for their unique properties, such as good conductivity, high corrosion resistance and excellent solderability. To further improve the mechanical performance of Cu-Sn-Zn coatings, powder-enhanced method was applied and Cu-Sn-Zn-TiO 2 nano-composite coatings with different TiO 2 concentration were fabricated. The microstructure of Cu-Sn-Zn-TiO 2 nano-composite coatings were investigated by X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM). The mechanical properties of coatings including microhardness and wear resistance were studied. The results indicate that the incorporation of TiO 2 nanoparticle can significantly influence the properties of Cu-Sn-Zn coatings. The microhardness of Cu-Sn-Zn coating was increased to 383 HV from 330 HV with 1 g/L TiO 2 addition. Also, the corrosion resistance of coating was enhanced. The effects of TiO 2 nanoparticle concentration on the microstructure, mechanical properties and corrosion resistance of Cu-Sn-Zn-TiO 2 nano-composite coatings were discussed.

36 MATERIALS SCIENCE↗

A eutectic dual-phase design towards superior mechanical properties of heusler-type ferromagnetic shape memory alloys

Heusler-type ferromagnetic shape memory alloys possess attractive multifunctional properties, including magnetic field induced shape memory effect, magnetoresistance and magnetocaloric effect, owing to the unique concurrent magnetic and martensitic transformations. However, these intermetallics generally exhibit intrinsic high brittleness and low strength, which severely impede their workability for processing and applicability in real use. In this study, we demonstrate a new grain refining strategy by means of eutectic solidification to improve the mechanical properties in Ni-Mn-Sn-Fe alloys. In a fully eutectic microstructure, the average γ lamellae thickness was refined to ~170 nm and the composite showed a compressive strength of 1950 MPa, ductility of 19.5%, Young’s Modulus of 38 GPa, pseudoelasticity of 3.2% and high mechanical cyclic stability. The high mechanical performance is attributed to the effect of departmentalization of the brittle Heusler alloy by the densely distributed γ phase fine lamellae in resisting crack propagation. The eutectic Heusler composite exhibited a metamagnetic phase transformation, with a magnetic entropy change of 10.2 J/kg·K and a refrigeration capacity of 168 J/kg in a field change of 5 T.

36 MATERIALS SCIENCE↗

The enhancing performance of (Ba{sub 0.85}Ca{sub 0.15}Ti{sub 0.90}Zr{sub 0.10})O{sub 3} ceramics by tuning anatase–rutile phase structure

Graphical abstract: Titanium dioxide (TiO{sub 2}) with different phase structure had interesting influence on the crystal structure, microstructure, the sintering temperature and electrical properties. - Highlights: • BCZT ceramics were prepared using either anatase or rutile structures as Ti source. • Orthorhombic and tetragonal mixture structure was exhibited by adjusting Ti source. • The optimal properties were observed in BCZT ceramics with rutile titanium dioxide. - Abstract: To research effect of raw materials TiO{sub 2} with the phase structures on the crystal structure, microstructure and electrical properties of lead-free (Ba{sub 0.85}Ca{sub 0.15})(Ti{sub 0.90}Zr{sub 0.10})O{sub 3} (BCZT) ceramics, BCZT ceramics using either anatase or rutile as Ti source were synthesized by solid-state reaction. Titanium dioxide (TiO{sub 2}) with anatase/rutile phase structures had interesting influence on the crystal structure, microstructure and the sintering temperature by the X-ray diffraction and SEM, which also played an important role in improved electrical properties. The BCZT ceramics with rutile titanium dioxide demonstrated optimal piezoelectric and dielectric properties: d{sub 33} = 590 pC/N, k{sub p} = 0.46, ε{sub r} = 2810, tanδ = 0.014 and T{sub c} = 91 °C, which was obviously superior to BCZT ceramics with anatase titanium dioxide.

36 MATERIALS SCIENCE↗

NASA research on refractory compounds.

The behavior and properties of the refractory carbides, nitrides, and borides are being investigated by NASA as part of its research aimed at developing superior heat resistant materials for aerospace applications. Studies of the zirconium-carbon-oxygen system show that zirconium oxycarbides of different compositions and lattice parameters can be formed between 1500 C and 1900 C and are stable below 1500 C. More applied studies show that hot working generally improves the microstructure and therefore the strength of TiC and NbC. Sintering studies on UN indicate that very high densities can be achieved. Hot pressing of cermets of HfN and HfC produces good mechanical properties for high temperature bearing applications. Attempts to improve the impact resistance of boride composites by the addition of a nickel or carbon yarn were not overly successful.

Gangler, J. J.↗

Elucidating Design Rules toward Enhanced Solid-State Charge Transport in Oligoether-Functionalized Dioxythiophene-Based Alternating Copolymers

This study investigates the solid-state charge transport properties of the oxidized forms of dioxythiophene-based alternating copolymers consisting of an oligoether-functionalized 3,4-propylenedioxythiophene (ProDOT) copolymerized with different aryl groups, dimethyl ProDOT (DMP), 3,4-ethylenedioxythiophene (EDOT), and 3,4-phenylenedioxythiophene (PheDOT), respectively, to yield copolymers P(OE3)-D, P(OE3)-E, and P(OE3)-Ph. At a dopant concentration of 5 mM FeTos 3 , the electrical conductivities of these copolymers vary significantly (ranging between 9 and 195 S cm –1 ) with the EDOT copolymer, P(OE3)-E, achieving the highest electrical conductivity. UV–vis–NIR and X-ray spectroscopies show differences in both susceptibility to oxidative doping and extent of oxidation for the P(OE3) series, with P(OE3)-E being the most doped. Wide-angle X-ray scattering measurements indicate that P(OE3)-E generally demonstrates the lowest paracrystallinity values in the series, as well as relatively small π–π stacking distances. The significant (i.e., order of magnitude) increase in electrical conductivity of doped P(OE3)-E films versus doped P(OE3)-D or P(OE3)-Ph films can therefore be attributed to P(OE3)-E exhibiting both the highest carrier ratios in the P(OE3) series, along with good π–π overlap and local ordering (low paracrystallinity values). Furthermore, these trends in the extent of doping and paracrystallinity are consistent with the reduced Fermi energy level and transport function prefactor parameters calculated using the semilocalized transport (SLoT) model. Observed differences in carrier ratios at the transport edge (c t ) and reduced Fermi energies [η(c)] suggest a broader electronic band (better overlap and more delocalization) for the EDOT-incorporating P(OE3)-E polymer relative to P(OE3)-D and P(OE3)-Ph. Ultimately, we rationalize improvements in electrical conductivity due to microstructural and doping enhancements caused by EDOT incorporation, a structure–property relationship worth considering in the future design of highly electrically conductive systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗