SEARCH · Search NASA

Results for “load growth”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS1999

Debonding of Stitched Composite Joints: Testing and Analysis

The effect of stitches on the failure of a single lap joint configuration was determined in a combined experimental and analytical study. The experimental study was conducted to determine debond growth under static monotonic loading. The stitches were shown to delay the initiation ofthe debond and provide load transfer beyond the load necessary to completely debond the stitched lap joint. The strain energy release rates at the debond front were calculated using a finite element-based technique. Models of the unstitched configuration showed significant values of modes I and II across the width of the joint and showed that mode III is zero at the centerline but increases near the free edge. Models of the stitched configuration showed that the stitches effectively reduced mode I to zero, but had less of an effect on modes II and III.

Glaessgen, E. H.↗

NASA NTRS1999

Delamination and Stitched Failure in Stitched Composite Joints

The effect of stitches on the failure of a single lap joint configuration was determined in a combined experimental and finite element study. The experimental program was conducted to determine debond growth under static monotonic loading. The stitches were shown to delay the initiation of the debond and provide load transfer beyond the load necessary to completely debond the stitched lap joint. The experimentally determined debond length vs. applied load was used as an input parameter in the finite element analysis of both configurations. The strain energy release rates at the debond from were calculated using plate finite elements. Nonlinear fastener elements were used to model the stitches and multipoint constraints were used to model the contact problem. Models of the unstitched configuration showed significant values of modes I and II across the width of the joint and showed that mode III is zero at the centerline but increases near the free edge. Models of the stitched configuration showed that the stitches were effective in reducing mode I to zero, but had less of an effect on modes II and III.

Glaessgen, E. H.↗

NASA NTRS1995

Pollen and ovule development in Arabidopsis thaliana under spaceflight conditions

The development of pollen and ovules in Arabidopsis thaliana on the space shuttle 'Endeavour' (STS-54) was investigated. Plants were grown on nutrient agar for 14 days prior to loading into closed plant growth chambers that received light and temperature control inside the Plant Growth Unit flight hardware on the shuttle middeck. After 6 days in spaceflight the plants were retrieved and immediately dissected and processed for light and electron microscope observation. Reproductive development aborted at an early stage. Pistils were collapsed and ovules inside were seen to he empty. No viable pollen was observed from STS-54 plants; young microspores were deformed and empty. At a late stage, the cytoplasm of the pollen contracted and became disorganized, but the pollen wall developed and the exine appeared normal. The tapetum in the flight flowers degenerated at early stages. Ovules from STS-54 flight plants stopped growing and the integuments and nucellus collapsed and degenerated. The megasporocytes appeared abnormal and rarely underwent meiosis. Apparently they enlarged, or occasionally produced a dyad or tetrad, to assume the form of a female gametophyte with the single nucleus located in an egglike cell that lacks a cell wall. Synergids, polar nuclei, and antipodals were not observed. The results demonstrate the types of lesions occurring in plant reproductive material under spaceflight conditions.

STS-54 Shuttle Project↗

NASA NTRS1996

Cytochemical localization of reserves during seed development in Arabidopsis thaliana under spaceflight conditions

Successful development of seeds under spaceflight conditions has been an elusive goal of numerous long-duration experiments with plants on orbital spacecraft. Because carbohydrate metabolism undergoes changes when plants are grown in microgravity, developing seed storage reserves might be detrimentally affected during spaceflight. Seed development in Arabidopsis thaliana plants that flowered during 11 d in space on shuttle mission STS-68 has been investigated in this study. Plants were grown to the rosette stage (13 d) on a nutrient agar medium on the ground and loaded into the Plant Growth Unit flight hardware 18 h prior to lift-off. Plants were retrieved 3 h after landing and siliques were immediately removed from plants. Young seeds were fixed and processed for microscopic observation. Seeds in both the ground control and flight plants are similar in their morphology and size. The oldest seeds from these plants contain completely developed embryos and seed coats. These embryos developed radicle, hypocotyl, meristematic apical tissue, and differentiated cotyledons. Protoderm, procambium, and primary ground tissue had differentiated. Reserves such as starch and protein were deposited in the embryos during tissue differentiation. The aleurone layer contains a large quantity of storage protein and starch grains. A seed coat developed from integuments of the ovule with gradual change in cell composition and cell material deposition. Carbohydrates were deposited in outer integument cells especially in the outside cell walls. Starch grains decreased in number per cell in the integument during seed coat development. All these characteristics during seed development represent normal features in the ground control plants and show that the spaceflight environment does not prevent normal development of seeds in Arabidopsis.

STS-68 Shuttle Project↗

NASA NTRS2010

Pulse-Echo Phased Array Ultrasonic Inspection of Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS)

A PRSEUS test article was subjected to controlled impact on the skin face followed by static and cyclic axial compressions. Phased array ultrasonic inspection was conducted before impact, and after each of the test conditions. A linear phased array probe with a manual X-Y scanner was used for interrogation. Ultrasound showed a delamination between the skin and stringer flange adjacent to the impact. As designed, the stitching in the flange arrested the lateral flaw formation. Subsequent ultrasonic data showed no delamination growth due to continued loading. Keywords: Phased Array, Ultrasonics, Composites, Out-of-Autoclave

Phased array↗

NASA NTRS2019

Molten Target Sputtering: Non-Conventional Method for High Mobility Si0.15Ge0.85 Growth at 500°C

Since electrons travel over 100 times faster in Silicon-Germanium (SiGe) than in pure Si due to the low effective masses associated with Ge and SiGe-based devices continue to replace Si-based solid-state electronic devices. SiGe thin film on sapphire was successfully grown at 890°C, using a magnetron sputtering system within heteroepitaxial framework. However, SiGe growth at 890oC is a costly and difficult process to produce as a uniform wafer for semiconductor device manufacturing due to thermal soak times, and geometric thermal shadowing from the wafer holder. To leverage the semiconducting capabilities of SiGe, novel processing techniques for SiGe film growth with decreased thermal loading are required. This paper introduces the Molten Target Sputtering (MTS) method that produces high mobility SiGe on sapphire below 500°C. This non-conventional method has the advantage of high kinetic energy, high-energy latency, and high flux density of sputtered atoms by combining benefits of both magnetron sputtering and thermal evaporation. For the MTS method, a 1~2 mm (depth and width) ring-shaped groove was cut between the center magnet and surrounded by electromagnets creating a circular cavity between the copper plate and source target materials that melt the target material. The SiGe grown from the MTS shows continuous morphology and 99.7% single crystal Si0.15Ge0.85 films. The Hall electron mobilities of the Si0.15Ge0.85 are 456 sq. cmV(exp -1)s(exp -1) and 123.9 sq. cmV(exp -1)s(exp -1) at 5.59 x 10(exp 18) cubic cm and 3.5 x 10(exp 20) cubic cm carrier concentration at 22.38°C, respectively. This is approximately 5.5 times higher than that of Si and similar to the Ge value at equivalent carrier concentrations and temperatures.

High mobility SiGe↗

NASA NTRS2010

TPSAS-NF1676L-11096-DND

Phased array↗

NASA NTRSDate not supplied

Preparation for and Performance of a Pseudomonas aeruginosa Biofilm Experiment On Board the International Space Station

Biofilms are a problem on Earth given their ability to degrade the materials upon which they grow and due to their relevance to infections. Remarkably, 65% and 80% of infections and chronic diseases on Earth are associated with biofilms, respectively. In space, these problems' impact is higher because the crew's lives and mission success depend on nominal operation of mechanical systems. Furthermore, the isolated confined environment nature of spaceflight may increase the rates of disease transmission. In the case of the International Space Station (ISS), biofilms are an identified problem on the Environmental Control and Life Support System (ECLSS), namely on the water processor assembly (WPA). In late 2019, the Space Biofilms experiment launched towards ISS to (i) characterize the mass, thickness, morphology, and gene expression of biofilms formed in space with respect to matched Earth controls, (ii) interrogate the expression of antimicrobial resistance genes, and (iii) test novel materials as potential biofilm control strategies for future ECLSS components. For this, 288 bacterial samples were prepared prior to the launch of the Northrop Grumman CRS-12 mission from NASA's Wallops Flight Facility. The samples were integrated into the spaceflight hardware, BioServe's Fluid Processing Apparatus (FPA) packed in sets of eight in Group Activation Packs (GAP). Half of these samples were activated and terminated on orbit by NASA astronauts Jessica Meir and Christina Koch, while the remaining half were processed equivalently on Earth. The spaceflight bacterial samples of Space Biofilms returned on board SpaceX' CRS-19 Dragon spacecraft, in early 2020. We here describe the test campaign implemented to verify the experiment design and confirm it would enable us to achieve the project's scientific goals. This campaign ended with the Experiment Verification Test (EVT), from which we here present example morphology and transcriptomic results. We describe in detail the sample preparation prior to flight, including cleaning and sterilization of the coupons of six materials (SS316, passivated-SS316, lubricant impregnated surface, catheter-grade silicone with and without a nanotopography, and cellulose membrane), loading and integration of growth media, bacterial inoculum, fixative and preservative to enable experiment termination on orbit. Additionally, we describe the performance of the experiment on board the ISS, including crew activities, use of assets, temperature profile, and experiment timeline; all leading to a successful spaceflight experiment.

Pamela Flores↗

NASA NTRS2014

Progress of a Cross-Correlation Based Optical Strain Measurement Technique for Detecting Radial Growth on a Rotating Disk

The Aeronautical Sciences Project under NASA's Fundamental Aeronautics Program is interested in the development of novel measurement technologies, such as optical surface measurements for the in situ health monitoring of critical constituents of the internal flow path. In situ health monitoring has the potential to detect flaws, i.e. cracks in key components, such as engine turbine disks, before the flaws lead to catastrophic failure. The present study, aims to further validate and develop an optical strain measurement technique to measure the radial growth and strain field of an already cracked disk, mimicking the geometry of a sub-scale turbine engine disk, under loaded conditions in the NASA Glenn Research Center's High Precision Rotordynamics Laboratory. The technique offers potential fault detection by imaging an applied high-contrast random speckle pattern under unloaded and loaded conditions with a CCD camera. Spinning the cracked disk at high speeds (loaded conditions) induces an external load, resulting in a radial growth of the disk of approximately 50.0-μm in the flawed region and hence, a localized strain field. When imaging the cracked disk under static conditions, the disk will be undistorted; however, during rotation the cracked region will grow radially, thus causing the applied particle pattern to be 'shifted'. The resulting particle displacements between the two images is measured using the two-dimensional cross-correlation algorithms implemented in standard Particle Image Velocimetry (PIV) software to track the disk growth, which facilitates calculation of the localized strain field. A random particle distribution is adhered onto the surface of the cracked disk and two bench top experiments are carried out to evaluate the technique's ability to measure the induced particle displacements. The disk is shifted manually using a translation stage equipped with a fine micrometer and a hotplate is used to induce thermal growth of the disk, causing the particles to become shifted. For both experiments, reference and test images are acquired before and after the induced shifts, respectively, and then processed using PIV software. The controlled manual translation of the disk resulted in detection of the particle displacements accurate to ~1.75% of full scale and the thermal expansion experiment resulted in successful detection of the disk's thermal growth as compared to the calculated thermal expansion results. After validation of the technique through the induced shift experiments, the technique is implemented in the Rotordynamics Lab for preliminary assessment in a simulated engine environment. The discussion of the findings and plans for future work to improve upon the results are addressed in the paper.

rotordynamics↗

NASA NTRS1981

Fatigue crack growth in 7475-T651 aluminum alloy plate in hard vacuum and water vapor

Compact specimens of 25 mm thick aluminum alloy plate were subjected to constant amplitude fatigue testing at a load ratio of 0.2. Crack growth rates were determined at frequencies of 1 Hz and 10 Hz in hard vacuum and laboratory air, and in mixtures of water vapor and nitrogen at water vapor partial pressures ranging from 94 Pa to 3.8 kPa. A significant effect of water vapor on fatigue crack growth rates was observed at the lowest water vapor pressure tested. Crack rates changed little for pressures up to 1.03 kPa, but abruptly accelerated at higher pressures. At low stress intensity factor ranges, cracking rates at the lowest and highest water vapor pressure tested were, respectively, two and five times higher than rates in vacuum. Although a frequency was observed in laboratory air, cracking rates in water vapor and vacuum are insensitive to a ten-fold change in frequency. Surfaces of specimens tested in water vapor and vacuum exhibited different amounts of residual deformation. Reduced deformation on the fracture surfaces of the specimens tested in water vapor suggests embrittlement of the plastic zone ahead of the crack tip as a result of environmental interaction.

Dicus, D. L.↗

NASA NTRS1981

Tension-tension fatigue behavior of the Space Shuttle strain-isolation-pad material

The room temperature fatigue behavior of 0.41-cm (0.16-in) thick strain-isolation-pad (SIP) material was explored in a series of constant- and random-amplitude loading tests. The SIP material is used on the Space Shuttle to isolate the ceramic insulating tiles from the strains and deflections of the aluminum alloy airframe. In all tests, 12.7 by 12.7 cm (5.0 by 5.0 in) SIP specimens were subjected to tension-tension loading in the through-the-thickness direction at a frequency of 10 Hz. When subjected to cyclic loading, the SIP material exhibited a monotonic increase in thickness and a monotonic increase in tensile tangent moduli. The rate of thickness growth increased with increasing test stress level and decreased with increasing number cycles endured. Power law equations were found to provide a good representation of the thickness growth rate data. Tensile tangent moduli increased by as much as 80 percent during fatigue tests. Simple cumulative damage fatigue models predicted the mean thickness growth under random-amplitude loading with reasonable accuracy (factor of 2 on life).

Phillips, E. P.↗

NASA NTRS2018

Real Time Detection of Damage During Quasi-Static Loading of a Single Stringer Panel Using Passive Thermography

Real time nondestructive evaluation is required for composites load testing. The early detection and measurement of damage progression is important to understand failure modes. A single stringer panel was subjected to quasi-static loading to induce deformation which can result in the formation of delamination damage between the stiffener flange and skin. Passive thermography was used to detect damage in real time as a function of the applied load. The loading was stopped when damage growth was detected. Of particular interest was the early detection of damage formation which can be challenging, as compared to cyclic fatigue loading. Passive thermography data were acquired and processed in real time and revealed damaged areas due to heating from fiber breakage and delamination formation. The processed thermal imagery was also compared to acoustic emission and ultrasound data.

Zalameda, Joseph N.↗

NASA NTRS1997

The Merging of Fatigue and Fracture Mechanics Concepts: A Historical Perspective

The seventh Jerry L. Swedlow Memorial Lecture presents a review of some of the technical developments, that have occurred during the past 40 years, which have led to the merger of fatigue and fracture mechanics concepts. This review is made from the viewpoint of 'crack propagation.' As methods to observe the 'fatigue' process have improved, the formation of fatigue micro-cracks have been observed earlier in life and the measured crack sizes have become smaller. These observations suggest that fatigue damage can now be characterized by 'crack size.' In parallel, the crack-growth analysis methods, using stress-intensity factors, have also improved. But the effects of material inhomogeneities, crack-fracture mechanisms, and nonlinear behavior must now be included in these analyses. The discovery of crack-closure mechanisms, such as plasticity, roughness, and oxide/corrosion/fretting product debris, and the use of the effective stress-intensity factor range, has provided an engineering tool to predict small- and large-crack-growth rate behavior under service loading, conditions. These mechanisms have also provided a rationale for developing, new, damage-tolerant materials. This review suggests that small-crack growth behavior should be viewed as typical behavior, whereas large-crack threshold behavior should be viewed as the anomaly. Small-crack theory has unified 'fatigue' and 'fracture mechanics' concepts; and has bridged the cap between safe-life and durability/damage-tolerance design concepts.

Newman, James C., Jr.↗

NASA NTRSDate not supplied

Evaluating Microgreens Crop Readiness for Space Production

Microgreens are small-size, nutrient-rich, and fast-grown crops, which are considered as candidates for future space exploration missions. In particular, the ISS, the Lunar Gateway, and Mars and Lunar missions could benefit from growing microgreens to supplement astronaut diets in the near future. Research at NASA’s Kennedy Space Center has focused on (1) the selection of microgreens compatible species, (2) the evaluation of microgreens food safety, (3) the use of passive wicking, on-demand watering, and hydroponics cultivation, (4) simulated microgravity growth, (5) microgreen canopy gas exchange, and (6) harvesting techniques in microgravity. This interactive presentation summarizes this research. Microgreen species will be evaluated for their yield in relationship to the quantity of inputs – water, seeds, substrate, light intensity, photoperiod, crew time – required for their growth; for their organoleptic and sensory factors in order to down select species that are highly acceptable for humans; and for their microbial loads as detected in their growth environment and the food safety metrics of their edible tissue. Passive wicking, on-demand watering, and hydroponic systems are being studied as an efficient way to deliver essential nutrients and water to microgreens, included in a microgravity environment. Growth studies in simulated microgravity (using 3-dimensional clinostats) will assess microgreens growth relative to that in 1g. Gas exchange studies on microgreens canopies in various airflows will assess their photosynthesis and transpiration. Finally, a series of parabolic flights has enabled the evaluation of different harvesting and bagging techniques in microgravity. Indeed, traditional plant harvesting methods (scissors) in microgravity could generate significant microgreen debris in the space station cabin. Two innovative techniques, coupled to a dedicated bagging method, were designed and evaluated against the control, traditional, harvesting technique. This research was supported by grants from NASA KSC’s Independent Research and Technology Development Program, NASA’s Flight Opportunity Program, NASA Postdoctoral Program Fellowships (L.P. & C.J.) supported by NASA’s Space Biology program, and support from NASA’s Human Research Program.

Space Crop Production↗

NASA NTRSDate not supplied

Evaluating Microgreens Crop Readiness for Space Production.

Microgreens are small-size, nutrient-rich, and fast-grown crops, which are considered as candidates for future space exploration missions. In particular, the ISS, the Lunar Gateway, and Mars and Lunar missions could benefit from growing microgreens to supplement astronaut diets in the near future. Research at NASA’s Kennedy Space Center has focused on (1) the selection of microgreens compatible species, (2) the evaluation of microgreens food safety, (3) the use of passive wicking, on-demand watering, and hydroponics cultivation, (4) simulated microgravity growth, (5) microgreen canopy gas exchange, and (6) harvesting techniques in microgravity. This presentation summarizes this research. Microgreen species will be evaluated for their yield in relationship to the quantity of inputs – water, seeds, substrate, light intensity, photoperiod, crew time – required for their growth; for their organoleptic and sensory factors in order to down select species that are highly acceptable for humans; and for their microbial loads as detected in their growth environment and the food safety metrics of their edible tissue. Passive wicking, on-demand watering, and hydroponic systems are being studied as an efficient way to deliver essential nutrients and water to microgreens, included in a microgravity environment. Growth studies in simulated microgravity (using 3-dimensional clinostats) will assess microgreens growth relative to that in 1g. Gas exchange studies on microgreens canopies in various airflows will assess their photosynthesis and transpiration. Finally, a series of parabolic flights has enabled the evaluation of different harvesting and bagging techniques in microgravity. Indeed, traditional plant harvesting methods (scissors) in microgravity could generate significant microgreen debris in the space station cabin. Two innovative techniques, coupled to a dedicated bagging method, were designed and evaluated against the control, traditional, harvesting technique. This research was supported by grants from NASA KSC’s Independent Research and Technology Development Program, NASA’s Flight Opportunity Program, NASA Postdoctoral Program Fellowships (L.P. & C.J.) supported by NASA’s Space Biology program, and support from NASA’s Human Research Program.

crop↗

NASA NTRS2001

Root elongation against a constant force: experiment with a computerized feedback-controlled device

Axial force was applied to the root tip of corn (Zea mays L. cv. Merit) seedlings using a computerized, feedback-controlled mechanical device. The system's feedback capability allowed continuous control of a constant tip load, and the attached displacement transducer provided the time course of root elongation. Loads up to 7.5 g decreased the root elongation rate by 0.13 mm h-1 g-1, but loads 7.5 to 17.5 g decreased the growth rate by only 0.04 mm h-1 g-1. Loads higher than 18 g stopped root elongation completely. Measurement of the cross-sectional areas of the root tips indicated that the 18 g load had applied about 0.98 MPa of axial pressure to the root, thereby exceeding the root's ability to respond with increased turgor pressure. Recorded time-lapse images of loaded roots showed that radial thickening (swelling) occurred behind the root cap, whose cross-sectional area increased with tip load.

Non-NASA Center↗

NASA NTRS2024

Characterization of Low-Velocity Impact Damage in Toughened Non-Crimp Fabric Laminates

The damage response of resin-infused composites was investigated using quasi-static indentation (QSI) and instrumented drop-weight impact testing. The test specimens were composed of six layers of non-crimp fabrics where each layer contained +45°, 90°, −45°, and 0° plies. The goals of the testing were to identify damage responses that may differ from traditional thermoset materials and provide damage characterization data to evaluate current damage prediction analyses and aid improvements to current damage models. The damage was characterized using X-ray computed tomography (CT) and ultrasonic testing (UT). Incremental QSI loading was used on a single specimen to investigate damage growth in nine steps at progressively higher loads. Realtime acoustic emission data were used to determine the unloading points. Unlike typical thermoset composites, the force-displacement was smooth and showed no obvious indications of damage. The primary damage consisted of large lines of fiber fracture on the plies near the impact surface and delaminations through the thickness. Nine specimens were impacted at nominal impact energies of 25 ft-lbs, 30 ft-lbs, and 35 ft-lbs. The force histories at each energy followed nearly identical paths. Again, no obvious signs of damage were observed in any of the force histories. The general damage response in the dynamic tests was similar to the QSI-loaded specimens. However, repeat specimens impacted with a given impact energy showed variations in the damage. Some characteristics of the damage response were different than those typically observed in thermoset composites and will need to be evaluated using current analysis methods.

Composite Materials↗

NASA NTRSDate not supplied

Characterization of Low-Velocity Impact Damage in Toughened Non-Crimp Fabric Laminates

Composite Materials↗