Search NASA⌕ Search

SEARCH · Search NASA

Results for “lunar processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Process Development and Testing for Lunar Habitats

Non-metallic composites are appealing for Lunar habitats due to their low specific weight and contribution to passive radiation shielding. This application of composite materials presents notable challenges, however: flammability risks are higher due to elevated oxygen levels expected in habitat structures and absorbed radiation can cause damage long-term. The Materials and Processes Laboratory at Marshall Space Flight Center awarded funding for an internal research and development study which included fabrication and testing of composite materials for Lunar habitats. Composite layups used carbon fiber or ultra-high molecular weight polyethylene reinforcement and a variety of polymer matrices. Pre-impregnated fabric was autoclave cured; however, novel coatings were incorporated during select layups. Samples from each panel were used for screening-level flammability testing (ASTM D 2863) and combined vacuum ultraviolet and electron irradiation followed by tension testing (ASTM D5766). Two of the tested composite materials exceeded a 37% limiting oxygen index. Material property degradation for a 10 year simulated radiation dose was minimal in most cases.

manufacturing↗

Spotlight-Mode Synthetic Aperture Radar Processing for High-Resolution Lunar Mapping

During the 2008-2009 year, the Goldstone Solar System Radar was upgraded to support radar mapping of the lunar poles at 4 m resolution. The finer resolution of the new system and the accompanying migration through resolution cells called for spotlight, rather than delay-Doppler, imaging techniques. A new pre-processing system supports fast-time Doppler removal and motion compensation to a point. Two spotlight imaging techniques which compensate for phase errors due to i) out of focus-plane motion of the radar and ii) local topography, have been implemented and tested. One is based on the polar format algorithm followed by a unique autofocus technique, the other is a full bistatic time-domain backprojection technique. The processing system yields imagery of the specified resolution. Products enabled by this new system include topographic mapping through radar interferometry, and change detection techniques (amplitude and coherent change) for geolocation of the NASA LCROSS mission impact site.

SAR↗

Space Station Freedom flight operations in support of exploration missions

The operational requirements on Space Station Freedom (SSF) for supporting the Lunar Phase of the Space Exploration Initiative (SEI) are examined, and a concept is developed for carrying out these operations. Attention is given to the types of events and tasks that must be performed on the SSF to process the lunar vehicles, as well as to resources required for the SSF and the methods of meeting the operational requirements of the lunar missions. Critical technology areas and needs that must be addressed to enable lunar missions are also discussed.

Brender, Karen D.↗

Space Resources Roundtable 2

Contents include following: Developing Technologies for Space Resource Utilization - Concept for a Planetary Engineering Research Institute. Results of a Conceptual Systems Analysis of Systems for 200 m Deep Sampling of the Martian Subsurface. The Role of Near-Earth Asteroids in Long-Term Platinum Supply. Core Drilling for Extra-Terrestrial Mining. Recommendations by the "LSP and Manufacturing" Group to the NSF-NASA Workshop on Autonomous Construction and Manufacturing for Space Electrical Power Systems. Plasma Processing of Lunar and Planetary Materials. Percussive Force Magnitude in Permafrost. Summary of the Issues Regarding the Martian Subsurface Explorer. A Costing Strategy for Manufacturing in Orbit Using Extraterrestrial Resources. Mine Planning for Asteroid Orebodies. Organic-based Dissolution of Silicates: A New Approach to Element Extraction from LunarRegohth. Historic Frontier Processes Active in Future Space-based Mineral Extraction. The Near-Earth Space Surveillance (NIESS) Mission: Discovery, Tracking, and Characterization of Asteroids, Comets, and Artificial Satellites with a microsatellite. Privatized Space Resource Property Ownership. The Fabrication of Silicon Solar Cells on the Moon Using In-Situ Resources. A New Strategy for Exploration Technology Development: The Human Exploration and Development of Space (HEDS) Exploratiori/Commercialization Technology Initiative. Space Resources for Space Tourism. Recovery of Volatiles from the Moon and Associated Issues. Preliminary Analysis of a Small Robot for Martian Regolith Excavation. The Registration of Space-based Property. Continuous Processing with Mars Gases. Drilling and Logging in Space; An Oil-Well Perspective. LORPEX for Power Surges: Drilling, Rock Crushing. An End-To-End Near-Earth Asteroid Resource Exploitation Plan. An Engineering and Cost Model for Human Space Settlement Architectures: Focus on Space Hotels and Moon/Mars Exploration. The Development and Realization of a Silicon-60-based Economy in CisLunar Space. Our Lunar Destiny: Creating a Lunar Economy. Cost-Effective Approaches to Lunar Passenger Transportation. Lunar Mineral Resources: Extraction and Application. Space Resources Development - The Link Between Human Exploration and the Long-term Commercialization of Space. Toward a More Comprehensive Evaluation of Space Information. Development of Metal Casting Molds by Sol-Gel Technology Using Planetary Resources. A New Concept in Planetary Exploration: ISRU with Power Bursts. Bold Space Ventures Require Fervent Public Support. Hot-pressed Iron from Lunar Soil. The Lunar Dust Problem: A Possible Remedy. Considerations on Use of Lunar Regolith in Lunar Constructions. Experimental Study on Water Production by Hydrogen Reduction of Lunar Soil Simulant in a Fixed Bed Reactor.

Ignatiev, A.↗

Evaluating the Efficacy of the Cloud for Cluster Computation

Computing requirements vary by industry, and it follows that NASA and other research organizations have computing demands that fall outside the mainstream. While cloud computing made rapid inroads for tasks such as powering web applications, performance issues on highly distributed tasks hindered early adoption for scientific computation. One venture to address this problem is Nebula, NASA's homegrown cloud project tasked with delivering science-quality cloud computing resources. However, another industry development is Amazon's high-performance computing (HPC) instances on Elastic Cloud Compute (EC2) that promises improved performance for cluster computation. This paper presents results from a series of benchmarks run on Amazon EC2 and discusses the efficacy of current commercial cloud technology for running scientific applications across a cluster. In particular, a 240-core cluster of cloud instances achieved 2 TFLOPS on High-Performance Linpack (HPL) at 70% of theoretical computational performance. The cluster's local network also demonstrated sub-100 ?s inter-process latency with sustained inter-node throughput in excess of 8 Gbps. Beyond HPL, a real-world Hadoop image processing task from NASA's Lunar Mapping and Modeling Project (LMMP) was run on a 29 instance cluster to process lunar and Martian surface images with sizes on the order of tens of gigapixels. These results demonstrate that while not a rival of dedicated supercomputing clusters, commercial cloud technology is now a feasible option for moderately demanding scientific workloads.

Cloud Computing↗

The process of crater removal in the lunar maria, part P

Near-terminator photography from the Apollo 14 and 15 missions is used as a basis to evaluate the processes by which craters disappear from the lunar surface. From observations and analyses it is concluded that: (1) The erosion of lunar craters in the size range of 10 m to 1 km is effected principally by small impacts producing minute changes in crater form up to the point where the crater is worn to an interior slope of approximately 1 degree. Below that slope, the annihilation process is dominated by the formation of younger overlapping craters. (2) The distribution of shapes of craters in this size range can be explained as resulting from impact generated processes.

Soderblom, L. A.↗

A review of earth-based radar mapping of the moon

Lunar radar mappings carried out in the late 1960s and 1970s have provided several valuable insights into lunar surface processes. These radar mappings used the delay-Doppler technique and needed the narrow antenna beams now available with large radio telescopes. Two-element radar interferometers have provided resolution of the delay-Doppler ambiguity at meter wavelengths and provided topographic information at centimeter wavelengths. These techniques have provided high resolution lunar radar maps at 3.8-cm, 70-cm, and 7.5-m wavelengths, a set of wavelengths which span the window available for earth-based radar mapping of the moon. These radar maps have been used along with other earth-based and Apollo orbital measurements to define surface units. The radar maps and these other data can describe physical properties such as small-scale blockiness and surface chemistry.

Thompson, T. W.↗

Nanoscale Compositional Relations in Lunar Rock Patina: Deciphering Sources for Patina Components on an Apollo 17 Station 6 Boulder

Space weathering on the Moon and other airless bodies modifies the surfaces of regolith grains as well as the space-exposed surfaces of larger rocks and boulders. As space weathering witness plates, rocks and boulders are distinguished from regolith grains based on their ability to persist as physically intact substrates over longer time scales before being disaggregated by impact processes. Because lunar surfaces, including exposed rocks, quickly develop an optically thick layer of patina, it is important to understand the compositional relationship between patinas and their underlying rock substrates, particularly to support remote-sensing of rocky lunar terrains. Based on analytical TEM techniques, supported by focused ion beam (FIB) cross-sectioning, we have begun to systematize the multi-layer microstructural complexity of patinas on rock samples with a range of space exposure histories. Our on-going work has particularly focused on lunar rock 76015, both because it has a long (approx. 22 my) exposure history, and because its surface was exposed to patina development approximately 1 m off the regolith surface on a boulder in the Apollo 17 Station 6 boulder field. Potential sources for the 76015 patina therefore include impact-melted and vaporized material derived from the local rock substrate, as well as from the mix of large boulders and regolith in the Station 6 area. While similar, there are differences in the mineralogy and chemistry of the rocks and regolith at Station 6. We were interested to see if these, or other sources, could be distinguished in the average composition, as well as the compositional nanostratigraphy of the 76015 patina. To date we have acquired a total of 9 TEM FIB cross-sections from the 76015 patina, giving us reasonable confidence of being able to arrive at an integrated average for the patina major element composition based on analytical TEM methods.

Christoffersen, R.↗

A lunar soil evolution model

Comminution, agglutination, and replenishment processes in a lunar soil are modeled by a system of time-dependent linear differential equations. In the model, a soil is subdivided into coarse-particle, fine-particle, and agglutinate fractions. The relative mass abundance of each component in a mature soil is found to be proportional to rates for the reworking processes. Evolution of the grain-size distribution from a fresh ejecta blanket to a mature soil is described quantitatively in terms of the changing proportions of the three soil constituents. If size data are available for an immature soil and a mature soil of the same system, rates for the various processes can be calculated under certain simplifying assumptions.

Mendell, W. W.↗

Making Thin Sections from National Treasures: A Little Moon Rock Goes a Long Way

NASA’s Johnson Space Center curates the Apollo sample collection through their facilities in Houston, TX. It is a dual-purpose facility, intended both to store and preserve the precious samples, as well as to make them available for ongoing scientific study and public examination. The facilities consist of multiple vaults and lab spaces, including the Apollo Thin Section Lab. Although it is a part of the Curation facilities, this lab is intended to process specific lunar rock and dust samples into what are called “thin sections”. A thin section is a microscope slide with a very thin, highly polished slice of rock material mounted on it. These are used not only for microscope viewing, but also for a range of other sophisticated scientific instruments to map and measure fine details of the rock’s physical and chemical composition and structure. The process of making a thin section requires great care and patience and is an art in itself; each one is unique, and each sample can behave very differently while going through the same basic procedures. In general, it begins by taking a small chip of rock from a much larger sample. The rock fragment is placed within a small mold and liquid epoxy is poured over it and allowed to harden, producing what is called a “potted butt” (Figure 1). This is to stabilize the rock so that it won’t fragment or crumble during polishing, and to fill any cracks or voids within the rock. Once hardened, the epoxy on the bottom is carefully ground away to expose the rock surface within, which is then polished to a 1-micron finish. A thin new layer of fresh epoxy is then applied to the polished surface and used to mount it to a silica slide. Once the mounting epoxy has hardened, the potted butt is cut off less than one millimeter above the slide using a low-speed circular saw. This thin layer of sample material attached to the slide undergoes further grinding and polishing, typically bringing the sample thickness down to about 35 microns – roughly one third of the thickness of a human hair. The remaining potted butt is saved for future scientific investigations and can be re-polished and used again until all the rock material within it is used up. A single thin section can be reused countless times by numerous different researchers. In addition, thin sections are often exquisitely beautiful (Figure 2) and in some cases, lunar thin sections are used as public display samples, such as at the Smithsonian Air and Space Museum in Washington, DC. The production of thin sections allows an immense variety of research to be conducted on a tiny amount of rock or mineral material, allowing the bulk of the Apollo collection to stay pristine and unaltered, and thus, remain available for next generation of lunar scientists to further our insight into the Moon’s geological diversity, and to bring valuable new insights to our understanding of the origin of the Earth-Moon system.

J J Kent↗

A closed life-support system for space colonies

In 1975, a system design study was performed to examine a completely self-contained system for a permanent colony of 10,000 inhabitants in space. Fundamental to this design was the life support system. Since resupply from earth is prohibitive in transportation costs, it was decided to use a closed system with the initial supply of oxygen coming from processing of lunar ores, and the supply of carbon, nitrogen and hydrogen from earth. The problem of life support was treated starting with the nutritional and metabolic requirements for the human population, creating a food and water chain sufficient to supply these demands, adding the additional requirements for the animal and plant sources in the food chain, feeding back useful waste products, supplying water as required from different sources, and closing the loop by processing organic wastes into CO2. This concept places the burden of the system upon plants for O2 generation and waste processing the CO2 generation.

Johnson, R. D.↗

Recent Discoveries in Simulant Behavior and Regolith Handling

The past few years have seen an exciting increase in visibility for the use of in-situ resources to achieve sustainability at the Moon and Mars. This visibility and inclusion in the mission architectures has led to an explosion in the research and development of mining and processing of regolith at the Moon. However, there are still many fundamental issues regarding digging, transporting, and processing of lunar and Mars regolith that may slow the progress by multiple teams who need to understand these issues before proceeding with hardware development. The objective of this project is to utilize the same team of soil and thermal experts and unique facilities to allow for efficient and fast generation of fundamental data and dissemination of critical results to the larger community. The capability gaps being addressed include how to dig up hard, frozen resources, transport to the processing site, lifting/depositing into a hopper or reactor, and extracting the water, all without losing the primary product to the environment. Soil Seals: Much attention has been focused on the challenges with regolith inlet/outlet valves that must seal in process gases after being repeatedly ex-posed to abrasive regolith and dust particles. One possible solution that has been proposed is to design the inlet hopper or duct such that the bulk of regolith pro-vides sufficient sealing of the reactor. Tests are planned to parametrically measure the maximum del-ta-pressure that can be maintained across a column of soil before ‘blow-out’ occurs. Variables to be examined include column height and width, simulant type, and compaction.

Simulant↗

Process Development and Testing for Lunar Habitats

Non-metallic solutions for Lunar bases are appealing due to their light weight and ability to block many forms of radiation. Composite materials made from different combinations of these non-metallic materials enable effective mating of dissimilar materials for strong structures such as pressurized habitats. Inserting and manufacturing composite structural materials on the Moon presents several challenges, however: the oxygen levels inside pressurized habitats will be relatively high, radiation that is blocked causes damage and the lack of atmosphere results in a high-magnitude negative pressure environment. In the past two years, the Materials and Processes Lab (EM01) invested in two internal research and development (IRAD) proposals for testing and procurement of composite materials. One proposal endeavors to determine flammability and radiation damage of various composite materials with a focus on carbon fiber and ultra-high molecular weight polyethylene (UHWMPE). The other proposal enables procurement of chopped fiber spray equipment materials which will be used to develop a novel technique for chopped UHMWPE fiber layup, similar to the chopped fiberglass layups used for making large structures such a boat hulls and hot tubs.

Composite↗

Artemis Suit Material Optical Property Testing of Dust Exposed Fabrics

This paper highlights one aspect of NASA’s ongoing technology-infusion effort to design, fabricate, and test a next-generation outer shell fabric for a lunar Extravehicular Activity (EVA) space suit, a critical component of sustained lunar exploration. Managing thermal loads on the Moon is essential for astronaut safety and suit performance. The suit’s exterior fabric directly influences heat gain and loss through its optical properties: low solar absorptivity minimizes sunlight absorption, while high infrared emissivity aids radiative cooling. Lunar regolith complicates this balance. Its fine, abrasive particles possess unique optical behavior that can lower reflectivity and raise emissivity when embedded in or adhered to fabric surfaces, degrading thermal control and increasing the risk of overheating or cooling inefficiency. To quantify these effects, the Artemis Suit Materials (ASM) team measured solar absorptance and infrared emissivity of clean and dust-soiled Ortho Fabric, establishing beginning-of-life (BOL) and end-of-life (EOL) benchmarks. EOL conditions were simulated with a rotary tumbler abrasion process using lunar dust simulant and ceramic media to reproduce cumulative wear expected during surface operations. Tests also included unmodified fabrics and a fabric/film laminate system containing titanium dioxide to evaluate potential improvements in dust resistance and optical performance. Results from these evaluations provide critical insight into how lunar dust alters fabric thermal behavior and inform the design of bespoke suit materials that maintain required optical properties throughout mission life, supporting safe and effective long-duration EVA on the lunar surface.

space↗

Artemis Suit Material Optical Property Testing of Dust Exposed Fabrics

This paper highlights one aspect of NASA’s ongoing technology-infusion effort to design, fabricate, and test a next-generation outer shell fabric for a lunar Extravehicular Activity (EVA) space suit, a critical component of sustained lunar exploration. Managing thermal loads on the Moon is essential for astronaut safety and suit performance. The suit’s exterior fabric directly influences heat gain and loss through its optical properties: low solar absorptivity minimizes sunlight absorption, while high infrared emissivity aids radiative cooling. Lunar regolith complicates this balance. Its fine, abrasive particles possess unique optical behavior that can lower reflectivity and raise emissivity when embedded in or adhered to fabric surfaces, degrading thermal control and increasing the risk of overheating or cooling inefficiency. To quantify these effects, the Artemis Suit Materials (ASM) team measured solar absorptance and infrared emissivity of clean and dust-soiled Ortho Fabric, establishing beginning-of-life (BOL) and end-of-life (EOL) benchmarks. EOL conditions were simulated with a rotary tumbler abrasion process using lunar dust simulant and ceramic media to reproduce cumulative wear expected during surface operations. Tests also included unmodified fabrics and a fabric/film laminate system containing titanium dioxide to evaluate potential improvements in dust resistance and optical performance. Results from these evaluations provide critical insight into how lunar dust alters fabric thermal behavior and inform the design of bespoke suit materials that maintain required optical properties throughout mission life, supporting safe and effective long-duration EVA on the lunar surface.

Textile↗

Process to Create High-Fidelity Lunar Dust Simulants

A method was developed to create high-fidelity lunar dust simulants that better match the unique properties of lunar dust than the existing simulants. The new dust simulant is designed to more closely approximate the size, morphology, composition, and other important properties of lunar dust (including the presence of nanophase iron). A two-step process is required to create this dust simulant. The first step is to prepare a feedstock material that contains a high percentage of agglutinate-like particles with iron globules (including nanophase iron). The raw material selected must have the proper mineralogical composition. In the second processing step, the feedstock material from the first step is jet-milled to reduce the particle size to a range consistent with lunar dust.

Gustafson, Robert↗

NASA's Lunar Atmosphere and Dust Environment Explorer (LADEE)

Nearly 40 years have passed since the last Apollo missions investigated the mysteries of the lunar atmosphere and the question of levitated lunar dust. The most important questions remain: what is the composition, structure and variability of the tenuous lunar exosphere? What are its origins, transport mechanisms, and loss processes? Is lofted lunar dust the cause of the horizon glow observed by the Surveyor missions and Apollo astronauts? How does such levitated dust arise and move, what is its density, and what is its ultimate fate? The US National Academy of Sciences/National Research Council decadal surveys and the recent "Scientific Context for Exploration of the Moon" (SCEM) reports have identified studies of the pristine state of the lunar atmosphere and dust environment as among the leading priorities for future lunar science missions. These measurements have become particularly important since recent observations by the Lunar Crater Observation and Sensing Satellite (LCROSS) mission point to significant amounts of water and other volatiles sequestered within polar lunar cold traps. Moreover Chandrayaan/M3, EPOXI and Cassini/VIMS have identified molecular water and hydroxyl on lunar surface regolith grains. Variability in concentration suggests these species are likely to be present in the exosphere, and thus constitute a source for the cold traps. NASA s Lunar Atmosphere and Dust Environment Explorer (LADEE) is currently under development to address these goals. LADEE will determine the composition of the lunar atmosphere and investigate the processes that control its distribution and variability, including sources, sinks, and surface interactions. LADEE will also determine whether dust is present in the lunar exosphere, and reveal its sources and variability. LADEE s results are relevant to surface boundary exospheres and dust processes throughout the solar system, will address questions regarding the origin and evolution of lunar volatiles, and will have implications for future exploration activities. LADEE will be the first mission based on the Ames Common Bus design. LADEE employs a high heritage instrument payload: a Neutral Mass Spectrometer (NMS), an Ultraviolet/Visible Spectrometer (UVS), and the Lunar Dust Experiment (LDEX). It will also carry a space terminal as part of the Lunar Laser Communication Demonstration (LLCD), which is a technology demonstration. LLCD will also supply a ground terminal. LLCD is funded by the Space Operations Mission Directorate (SOMD), managed by GSFC, and built by MIT Lincoln Lab. NMS was directed to the Goddard Space Flight Center (GSFC) and UVS to Ames Research Center (ARC). LDEX was selected through the Stand Alone Missions of Opportunity Notice (SALMON) Acquisition Process, and is provided by the University of Colorado at Boulder. The LADEE NMS covers a m/z range of 2-150 and draws its design from mass spectrometers developed at GSFC for the MSL/SAM, Cassini Orbiter, CONTOUR, and MAVEN missions. The UVS instrument is a next-generation, high-reliability version of the LCROSS UV-Vis spectrometer, spanning 250-800 nm wavelength, with high (<1 nm) spectral resolution. UVS will also perform dust occultation measurements via a solar viewer optic. LDEX senses dust impacts in situ, at LADEE orbital altitudes of 50 km and below, with a particle size range of between 100 nm and 5 micron. Dust particle impacts on a large hemispherical target create electron and ion pairs. The latter are focused and accelerated in an electric field and detected at a microchannel plate. LADEE is an important part of NASA s portfolio of near-term lunar missions; launch is planned for May, 2013. The lunar atmosphere is the most accessible example of a surface boundary exosphere, and may reveal the sources and cycling of volatiles. Dynamic dust activity must be accounted for in the design and operation of lunar surface operations.

Elphic, Richard↗