Search NASA⌕ Search

SEARCH · Search NASA

Results for “optical efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Field Deployable Mirror Soiling Detection Based on Polarimetric Imaging

Heliostat mirror soiling is one of the significant factors for reduced optical efficiency of Concentrated Solar Power (CSP) fields. However, it remains challenging to determine the mirror soiling patterns across the large area of the CSP field. Here we propose a fast and field deployable inspection method to measure the heliostat mirror soiling levels based on polarization images in regular daylight settings without additional light sources. Under sunny and clear sky conditions, we have demonstrated accurate measurement of reflection efficiency (error ~1%) for mirrors with different soiling levels.

14 SOLAR ENERGY↗

Development of the design of a between-the-lens band type photographic shutter

When photographic equipment is miniaturized, in order to conserve weight and size for spacecraft use, by using wide angle, short focus lenses, a band-type central between-the-lens shutter must be used. The rectangular slot shape was the form with the highest optical efficiency. To overcome the problem of burrs caused in the punching out of the slots in a carbon steel band, a shape limited by arcs with radius equal to half the slot width is preferred.

Dorofeyev, A. S.↗

InSb charge coupled infrared imaging device: The 20 element linear imager

The design and fabrication of the 8585 InSb charge coupled infrared imaging device (CCIRID) chip are reported. The InSb material characteristics are described along with mask and process modifications. Test results for the 2- and 20-element CCIRID's are discussed, including gate oxide characteristics, charge transfer efficiency, optical mode of operation, and development of the surface potential diagram.

Thom, R. D.↗

Optical, thermal, and electrical performance of low-CR solar arrays

This paper describes the analysis and testing of a photovoltaic low-CR concentrator shaped like a truncated pyramid with an aperture of 0.5 m on a side and a geometric concentration ratio of six. The truncated base plane is covered by either silicon (Si) or gallium arsenide (GaAs) solar cells. Ray-trace analysis of the concentrator predicts a peak optical efficiency of 0.77, which falls off only gradually with pointing error. A coupled thermal-electrical analysis of the system shows that the moderately nonuniform illumination produced by the concentrator does not result in significant mismatch losses, provided the solar cells are connected in parallel groups. The results of ground tests involving a full-scale prototype concentrator conform well with theoretical predictions.

French, E. P.↗

Development of a Fresnel lens concentrator for space application

The selected conceptual design of the dome lens photovoltaic concentrator for space applications uses a 3.7 cm square aperture dome lens to focus onto a 0.4 cm active diameter gallium arsenide cell. The selected configuration will provide 91.5 percent lens optical efficiency and 21.4 percent cell efficiency at 100 suns irradiance and 100 C cell temperature, for an overall cell efficiency of 19.6 percent. The selected configuration will tolerate 1 degree tracking errors with negligible loss of performance. The selected panel weight is 2.5 kg/sq.m.

Oneill, Mark J.↗

Diode laser-pumped solid-state lasers

An evaluation is made of the consequences for solid-state lasers of novel diode laser-pumping technology. Diode laser-pumped neodymium lasers have operated at an electrical-to-optical efficiency of 10 percent in a single spatial mode, with linewidths of less than 10 kHz, and with a spectral power brightness sufficiently great to allow frequency extension by harmonic generation in nonlinear crystals; this has yielded green and blue sources of coherent radiation. Q-switched operation with kW peak powers and mode-locked operation with 10-picosec pulse widths have also been demonstrated. All-solid-state lasers at prices comparable to those of current flash-lamp-pumped laser systems are foreseen, as are power levels exceeding 1 kW, for coherent radar, global satellite sensing, and micromachining.

Byer, Robert L.↗

Test results on parabolic dish concentrators for solar thermal power systems

This paper presents results of development testing of various solar thermal parabolic dish concentrators. The concentrators were mostly designed for the production of electric power using dish-mounted Rankine, Brayton or Stirling cycle engines, intended to be produced at low cost. Measured performance for various dishes included optical efficiencies ranging from 0.32 to 0.86 at a geometric concentration ratio of 500, and from about 0.09 to 0.85 at a geometric concentration ratio of 3000. Some malfunctions were observed. The tests should provide operating information of value in developing concentrators with improved performance and reduced maintenance.

Jaffe, Leonard D.↗

Fabrication of sensitive high Tc bolometers

The rapid change of resistance with temperature of high quality films of high T sub c superconductors can be used to make resistance thermometers with very low temperature noise. Measurements on c-axis yttrium barium copper oxide (YBCO) films have given a spectral intensity of temperature noise less than 4 times 10(exp -8) K/Hz(exp 1/2) at 10 Hz. Consequently, the opportunity exists to make useful bolometric infrared detectors that operate near 90 K which can be cooled with liquid nitrogen. The fabrication and measurement of two bolometer architectures are discussed. The first is a conventional bolometer which consists of a 3000 A thick YBCO film deposited in situ by laser ablation on top of a 500 A thick SrTiO3 thickness and diced into 1x1 mm(exp 2) bolometer chips. Gold black smoke was used as the radiation absorber. The voltage noise was less than the amplifier noise when the film was current biased. Optical measurements gave an NEP of 5 times 10(exp -11) W/Hz(exp 1/2) at 10 Hz. The second architecture is that of an antenna-coupled microbolometer which consists of a small (5x10 cubic microns) YBCO film deposited directly on a bulk substrate with a low thermal conductance (YSZ) and an impedance matched planar lithographed spiral or log-periodic antenna. This structure is produced by standard photolithographic techniques. Measurements gave an electrical NEP of 4.7 times 10(exp -12) W/Hz(exp 1/2) at 10 kHz. Measurements of the optical efficiency are in progress. The measured performance of both bolometers will be compared to other detectors operating at or above liquid nitrogen temperatures so as to identify potential applications.

Nahum, Michael↗

High altitude AM0 testing of PV concentrator lens elements

Recently, the NASA Lewis Research Center modified its Lear High Altitude Test Facility to fly two prototype ENTECH minidome Fresnel lens photovoltaic concentrator elements. The tests were highly successful, and the results verified the ability of the Lear High Altitude Facility to measure the optical performance of individual concentrator lens elements and concentrator/cell combinations at near AM0 insolation conditions. The two concentrator lenses flown achieved optical efficiencies, based on a gallium arsenide concentrator cell response, of 89.8 percent and 90.0 percent. The flights demonstrated the ability of the aircraft to maintain the pointing accuracy required to obtain useful data. With proper alignment of the collimating tube and the pilot's sunsight, this facility could easily maintain a pointing accuracy of + or - 0.5 deg for a sufficiently long time to obtain accurate, reproducible results.

Piszczor, M. F.↗

One joule output from a diode-array-pumped Nd:YAG laser with side-pumped rod geometry

Output of 1.25 J per pulse (1.064 micron) with an absolute optical efficiency of 28 percent and corresponding electrical efficiency of 10 percent was demonstrated in a diode-array-pumped Nd:YAG laser using a side-pumped rod geometry in a master-oscillator/power-amplifier configuration. In Q-switched operation, an output of 0.75 J in a 17-ns pulse was obtained. The fundamental laser output was frequency doubled in KTP with 60 percent conversion efficiency to obtain 0.45 J in a 16-ns pulse at 532 nm. The output beam had high spatial quality with pointing stability better than 40 microrad and a shot-to-shot pulse energy fluctuation of less than +/-3 percent.

Kasinski, Jeffrey J.↗

Holmium YLF amplifier performance and the prospects for multi-Joule energies using diode-laser pumping

Laser studies were performed to examine the amplifier characteristics of holmium-doped yttrium lithium fluoride (YLF) at 300 K. An inversion ratio of 0.37 was reached resulting in a measured small-signal gain coefficient of 0.50/cm. In a flashlamp pumping experiment, an output energy of 240 mJ was achieved for 38.5 mJ of input energy resulting in a large gain of 6.2. An amplifier model was developed for diode laser pumping and adapted to consider this flashlamp-pumped case. There is good agreement between the theory and experiment. Multipass amplifier calculations using the model suggest that the Ho: Tm: YLF laser crystal can support a 12 percent electrical to optical efficiency at 300 K even in the presence of upconversion.

Storm, Mark E.↗

Diode pumped, regenerative Nd:YAG ring amplifier for space application

The study reviews the research and development of a prototype laser used to study one possible method of short-pulse production and amplification, in particular, a pulsed Nd:YAG ring laser pumped by laser diode arrays and injected seeded by a 100-ps source. The diode array pumped, regenerative amplifier consists of only five optical elements, two mirrors, one thin film polarizer, one Nd:YAG crystal, and one pockels cell. The pockels cell performed both as a Q-switch and a cavity dumper for amplified pulse ejection through the thin film polarizer. The total optical efficiency was low principally due to the low gain provided by the 2-bar pumped laser head. After comparison with a computer model, a real seed threshold of about 10 exp -15 J was achieved because only about 0.1 percent of the injected energy mode-matched with the ring.

Coyle, D. B.↗

Long-pulse-length 2-micron diode-pumped YLiF4 laser

A diode-pumped Ho:Tm:YLiF4 laser at room temperature has achieved an optical efficiency of 5.9 percent under normal-mode operation. Long pulse lengths, of the order of 1 microsec, have been obtained by use of 4-m ring resonator, with laser energy output of 15 mJ in single Q-switched pulses for an input energy of 2.078 J.

Jani, Mahendra G.↗

Properties of a B0 I stellar wind and interstellar grains derived from Ginga observations of the binary X-ray pulsar 4U 1538-52

From measurements of the X-ray eclipse phenomena of the binary X-ray pulsar 4U 1538-52, we derive properties of the stellar wind of its B0 I companion, QV Nor, and a constraint on models of interstellar grains. Estimates of the wind density as a function of the distance from the center of QV Nor are obtained from an analysis of the variation of X-ray attenuation during an eclipse egress. A Monte Carlo computation of the absorption and scattering of X-rays in the X-ray-ionized wind accounts for approximately two-thirds of the spectrum of X-rays with energies above 4.5 keV observed during the eclipse. Our upper limit on R(sub XV) is 0.06/mag, which implies that the X-ray scattering efficiency of interstellar dust is less than expected for solid grains with a size distribution of the form n(sub g)(a) approximately a(exp -3.5) in the range from 0.005 to 0.25 microns and composed of silicate (R(sub XV) = 0.22/mag) or a silicate-graphite mixture (R(sub XV) = 0.11/mag) as derived from the calculations of Martin & Rouleau (1991). This lends support to the idea (Mathis & Whiffen 1989) that interstellar grains are 'fluffy' aggregates with an average bulk density less than that of their constitutent particles. Such aggregates would have a smaller ratio of X-ray scattering efficiency to optical extinction efficiency compared with solid grains of the same material.

Clark, George W.↗

Diode-Pumped Long-Pulse-Length Ho:Tm:YLiF4 Laser at 10 Hz

An optical efficiency of 0.052 under normal mode operation for diode-pumped Ho:Tm:YLiF4 at a pulse repetition frequency of 10 Hz has been achieved. Laser output energy of 30 mJ in single Q-switched pulses with 600-ns pulse length were obtained for an input energy of 3 J. A diffusion-bonded birefringent laser rod consisting of Ho:Tm-doped and undoped pieces of YLF was utilized for 10-Hz operation.

Jani, Mahendra G.↗

Lattice Dynamics of Colloidal Crystals During Photopolymerization of Acrylic Monomer Matrix

Polymerization process are the major contributors for observed lattice compression and lattice disorder of the Crystalline Colloidal Arrays (CCA) of silica spheres in polymerized acrylic/methacrylic ester films. The effect of orientation of photocell with respect to the readiation source on Bragg diffraction of CCA indicated the presence of convective stirring in thin fluid system during the photopolymerization that deleteriously affect the periodic array structures. To devise reproducible and more efficient optical filters, experimental methods to minimize or eliminate convective instabilities in monomeric dispersions during polymerization are suggested.

Sunkara, Hari B.↗

An Ozone Differential Absorption Lidar (DIAL) Receiver System for Use on Unpiloted Atmospheric Vehicles

Measurements of global atmosphere ozone concentrations call for flexible lidar systems that can be operated from an unpiloted atmospheric vehicle (UAV) to reduce the cost of measurement missions. A lidar receiver system consisting of a fiber-optic-coupled telescope has been designed and tested for this purpose. The system weight is 13 kg and its volume of 0.06 m 3 would fit into the payload compartment of a Perseus B UAV. The optical efficiency of the telescope is 37 percent at 288 nm and 64 percent at 300 nm. Atmospheric measurements with a DIAL laser system have been performed, and the measured ozone density has matched the data from ozonesondes to an altitude of 7 km.

DeYoung, Russell J.↗

Development of a Submillimeter/Far-Infrared Radiometer for Cirrus Measurements

We introduce a low-cost, lightweight and compact polarisation-sensitive radiometer for the measurement of Cirrus clouds in the submillimeter and far-infrared region (10 150 cm-1). It is widely recognised that enhanced global measurements of cirrus properties are essential to the development of General Circulation and Climate Prediction Models since cirrus clouds have a strong effect on the Earth's Global Radiation Budget. The purpose of this project is to design and build a novel instrument suitable for aircraft deployment in order to measure Ice Water Path (IWP) along with cirrus particle size and shape. This airborne instrument, which is currently under development in Cardiff, will serve as a prototype for a future satellite-based radiometer. The radiometer will capitalize on the ongoing measurements of the NASA-led, Fourier Transform interferometer-based, FIRSC (Far-Infrared Sensor for Cirrus) instrument for which Cardiff has been closely associated. Data from FIRSC campaigns is being used to select optimum radiometer channels that exhibit good sensitivity to specific cirrus. This new multichannel radiometer will, however, have some key advantages over similar spectroscopic instruments, for example, portability, increased optical efficiency, a multi-angle field of view and a reduced integration period leading to an improved spatial resolution. The radiometer will benefit from the application of state-of-the-art submm/FIR polarizer and solid filter technology currently being developed in Cardiff. The instrument will require a detector array that is robust enough to withstand aircraft/space deployment.

Hayton, Darren↗