Results for “oxidizing environments” — Page 15

NASA NTRSDate not supplied

Process Development and Hot-fire Testing of Additively Manufactured NASA HR-1 for Liquid Rocket Engine Applications

Additive manufacturing (AM) has provided new design and manufacturing opportunities to reduce cost and schedules, consolidate parts, and optimize performance. One technique being evaluated is Laser Powder Directed Energy Deposition (LP-DED), which provides a significant increase in scale compared to Laser Powder Bed Fusion (L-PBF). NASA along with industry partners have been developing the LP-DED process to demonstrate internal channel geometry and development components for use in liquid rocket engine channel cooled nozzles. Optimized materials in the extreme high pressure and hydrogen environment for liquid rocket engines remains a key challenge. NASA has advanced an enabling material called NASA HR-1 (Hydrogen Resistant -1) as a solution using AM techniques. NASA HR-1 is a high-strength Fe-Ni superalloy designed to resist high pressure, hydrogen environment embrittlement, oxidation, and corrosion. NASA HR-1 meets materials requirements for liquid rocket engine components, including good hydrogen resistance, high conductivity, good low cycle fatigue performance, and high elongation and strength for components in high heat flux environments. Material properties and process characterization have been completed on the high density thin-wall material in addition to advancements of the supply chain. NASA has also completed fabrication of several subscale and full-scale channel wall nozzles in LP-DED NASA HR-1 and completed hot-fire testing. This includes refinement of the process to produce thin-walls and various channel geometries to meet the requirements for channel wall nozzle applications. This paper will provide an overview of the LP-DED process development, material characterization and properties, component manufacturing, and hot-fire testing. Hot-fire testing was completed for a lander-class 7K-lbf thrust chamber using Liquid Oxygen (LOX)/Methane. The design overview and results from hot-fire testing will be presented in addition to hardware development for future testing on 2K-lbf and 35k-lbf thrust chambers and large-scale manufacturing technology demonstrators.

DED↗

NASA NTRSDate not supplied

Process Development and Hot-fire Testing of Additively Manufactured NASA HR-1 for Liquid Rocket Engine Applications

Additive manufacturing (AM) has provided new design and manufacturing opportunities to reduce cost and schedules, consolidate parts, and optimize performance. One technique being evaluated is Laser Powder Directed Energy Deposition (LP-DED), which provides a significant increase in scale compared to Laser Powder Bed Fusion (L-PBF). NASA along with industry partners have been developing the LP-DED process to demonstrate internal channel geometry and development components for use in liquid rocket engine channel cooled nozzles. Optimized materials in the extreme high pressure and hydrogen environment for liquid rocket engines remains a key challenge. NASA has advanced an enabling material called NASA HR-1 (Hydrogen Resistant -1) as a solution using AM techniques. NASA HR-1 is a high-strength Fe-Ni superalloy designed to resist high pressure, hydrogen environment embrittlement, oxidation, and corrosion. NASA HR-1 meets materials requirements for liquid rocket engine components, including good hydrogen resistance, high conductivity, good low cycle fatigue performance, and high elongation and strength for components in high heat flux environments. Material properties and process characterization have been completed on the high density thin-wall material in addition to advancements of the supply chain. NASA has also completed fabrication of several subscale and full-scale channel wall nozzles in LP-DED NASA HR-1 and completed hot-fire testing. This includes refinement of the process to produce thin-walls and various channel geometries to meet the requirements for channel wall nozzle applications. This paper will provide an overview of the LP-DED process development, material characterization and properties, component manufacturing, and hot-fire testing. Hot-fire testing was completed for a lander-class 7K-lbf thrust chamber using Liquid Oxygen (LOX)/Methane. The design overview and results from hot-fire testing will be presented in addition to hardware development for future testing on 2K-lbf and 35k-lbf thrust chambers and large-scale manufacturing technology demonstrators.

Additive Manufacturing↗

DOE OSTI2022

Functional CeO x nanoglues for robust atomically dispersed catalysts

Single-atom catalysts make exceptionally efficient use of expensive noble metals and can bring out unique properties. However, applications are usually compromised by limited catalyst stability, which is due to sintering. Although sintering can be suppressed by anchoring the metal atoms to oxide supports, strong metal–oxygen interactions often leave too few metal sites available for reactant binding and catalysis, and when exposed to reducing conditions at sufficiently high temperatures, even oxide-anchored single-atom catalysts eventually sinter. Here we show that the beneficial effects of anchoring can be enhanced by confining the atomically dispersed metal atoms on oxide nanoclusters or ‘nanoglues’, which themselves are dispersed and immobilized on a robust, high-surface-area support. We demonstrate the strategy by grafting isolated and defective CeO x nanoglue islands onto high-surface-area SiO 2 ; the nanoglue islands then each host on average one Pt atom. Further, we find that the Pt atoms remain dispersed under both oxidizing and reducing environments at high temperatures, and that the activated catalyst exhibits markedly increased activity for CO oxidation. We attribute the improved stability under reducing conditions to the support structure and the much stronger affinity of Pt atoms for CeO x than for SiO 2 , which ensures the Pt atoms can move but remain confined to their respective nanoglue islands. The strategy of using functional nanoglues to confine atomically dispersed metals and simultaneously enhance their reactivity is general, and we anticipate that it will take single-atom catalysts a step closer to practical applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1981

Hydrazines and carbohydrazides produced from oxidized carbon in earth's primitive environment

Whether abiological organic compounds can be formed from the interactions of energy sources with nitrogen, oxidized carbon and water is held to be of importance in geochemical models of the primordial earth atmosphere. It is reported that experiments using quenched spark discharges through molecular nitrogen on aqueous suspensions of CaCO3 and other reactants to simulate the hydrosphere/atmosphere interface yield hydrazine and carbohydrazine in significant but low yields. Such reactions in primitive aquatic environments may have supplied a pathway for chemical evolution and the origin of life, on a primitive earth in which fully oxidized states of carbon were available for the primary synthesis of organic matter.

Folsome, C. E.↗

DOE OSTI2024

Scheimpflug LIDAR for Gas Sensing at Elevated Temperatures

Localized operating conditions inside boilers, heat recovery steam generators, or other large thermal systems have a huge impact on the efficiency, environmental performance, and lifetime of components. It is extremely difficult to measure species accurately within these systems due to the high temperatures and harsh environments, locally oxidizing or reducing atmospheres, ash, other particulates, and other damaging chemical species. Physical probes quickly suffer damage and are rendered nonfunctional. This work has attempted to adapt the measurement approach based on Scheimpflug light detection and ranging (S-LIDAR) for the remote sensing of gas species inside the high-temperature boiler environment. For a proof-of-concept, the detection of Raman signals of N 2 , O 2 , and CO 2 and their behavior with increasing temperature have been presented.

47 OTHER INSTRUMENTATION↗

DOE OSTI2024

Resistance of Boron Nitride Nanotubes to Radiation-Induced Oxidation

We present unprecedented results on the damage thresholds and pathways for boron nitride nanotubes (BNNT) under the influence of energetic electrons in an oxidative gas environment, using an environmental aberration-corrected electron microscope over a range of oxygen pressures. We observe a damage cascade process that resists damage until a higher electron dose, compared with carbon nanotubes, initiating at defect-free BNNT sidewalls and proceeding through the conversion from crystalline nanotubes to amorphous boron nitride (BN), resisting oxidation throughout. We compare with prior results on the oxidation of carbon nanotubes and present a model that attributes the onset of damage in both cases to a physisorbed oxygen layer that reduces the threshold for damage onset. Surprisingly, increased temperatures offer protection against damage, as do electron dose rates that significantly exceed the oxygen dose rates, and our model attributes both effects to a physisorbed oxygen population.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Dataset for "Resistance of Boron Nitride Nanotubes to Radiation-Induced Oxidation" as published in The Journal of Physical Chemistry C

We present unprecedented results on the damage thresholds and pathways for boron nitride nanotubes (BNNT) under the influence of energetic electrons in an oxidative gas environment, using an environmental aberration-corrected electron microscope over a range of oxygen pressures. We observe a damage cascade process that resists damage until a higher electron dose, compared with carbon nanotubes, initiating at defect-free BNNT sidewalls and proceeding through the conversion from crystalline nanotubes to amorphous boron nitride (BN), resisting oxidation throughout. We compare with prior results on the oxidation of carbon nanotubes and present a model that attributes the onset of damage in both cases to a physisorbed oxygen layer that reduces the threshold for damage onset. Surprisingly, increased temperatures offer protection against damage, as do electron dose rates that significantly exceed the oxygen dose rates, and our model attributes both effects to a physisorbed oxygen population.

Adsorption↗

NASA NTRS2014

Protecting Neural Structures and Cognitive Function During Prolonged Space Flight by Targeting the Brain Derived Neurotrophic Factor Molecular Network

Brain derived neurotrophic factor (BDNF) is the main activity-dependent neurotrophin in the human nervous system. BDNF is implicated in production of new neurons from dentate gyrus stem cells (hippocampal neurogenesis), synapse formation, sprouting of new axons, growth of new axons, sprouting of new dendrites, and neuron survival. Alterations in the amount or activity of BDNF can produce significant detrimental changes to cortical function and synaptic transmission in the human brain. This can result in glial and neuronal dysfunction, which may contribute to a range of clinical conditions, spanning a number of learning, behavioral, and neurological disorders. There is an extensive body of work surrounding the BDNF molecular network, including BDNF gene polymorphisms, methylated BDNF gene promoters, multiple gene transcripts, varied BDNF functional proteins, and different BDNF receptors (whose activation differentially drive the neuron to neurogenesis or apoptosis). BDNF is also closely linked to mitochondrial biogenesis through PGC-1alpha, which can influence brain and muscle metabolic efficiency. BDNF AS A HUMAN SPACE FLIGHT COUNTERMEASURE TARGET Earth-based studies reveal that BDNF is negatively impacted by many of the conditions encountered in the space environment, including oxidative stress, radiation, psychological stressors, sleep deprivation, and many others. A growing body of work suggests that the BDNF network is responsive to a range of diet, nutrition, exercise, drug, and other types of influences. This section explores the BDNF network in the context of 1) protecting the brain and nervous system in the space environment, 2) optimizing neurobehavioral performance in space, and 3) reducing the residual effects of space flight on the nervous system on return to Earth

Schmidt, M. A.↗

DOE OSTI2023

Rigorous Oxidation State Assignments for Supported Ga-Containing Catalysts Using Theory-Informed X-ray Absorption Spectroscopy Signatures from Well-Defined Ga(I) and Ga(III) Compounds

Gallium-based heterogeneous catalysts originally developed for commercial use in propane dehydroaromatization have been explored extensively as potential replacements for Pt- and Cr-based catalysts used in propane dehydrogenation for on-demand propylene production. In a large number of experimental and theoretical studies, active sites with a variety of Ga nuclearities, coordination environments, and oxidation states have been proposed. Isolated Ga(I) ions are often invoked, despite the scarcity of well-defined molecular species and their well-documented instability. In this study, we investigate the appearance of a high-intensity, low-energy white line at the Ga K-edge upon reduction of Ga/HZSM-5 by H 2 at a temperature of ca. 500 °C, accompanied by a dramatic reduction in the extended X-ray absorption fine structure (EXAFS) intensity. In contrast, Ga/γ-Al 2 O 3 does not show such behavior. In order to lay a rigorous foundation for characterizing these types of systems and to establish experimental signatures for the elusive Ga(I) oxidation state, we recorded Ga K-edge X-ray absorption spectra [including high-energy-resolution fluorescence detection-X-ray absorption near-edge spectroscopy (HERFD-XANES)] for several well-defined molecular and crystalline Ga(I) compounds. XANES is essential to establishing the presence of Ga(I), despite the overlap in edge energies with organoGa(III) compounds, because Ga(I)-containing oxide materials show very weak EXAFS scattering. Compared to the XANES of trigonal Ga(III)-containing materials, Ga(I) spectra display a significantly more intense white line feature. Theoretical simulations agree well with this experimental observation and reveal that the strong XANES intensity originates from the superposition of transitions to several empty, nearly degenerate p-like states. Finally, these signatures provide compelling evidence for assigning the intense white line and dramatic loss of EXAFS intensity in Ga/HZSM-5 to the near-quantitative reduction of Ga(III) to Ga(I), while the weaker white line and conventional EXAFS signal of Ga/γ-Al 2 O 3 point to, at most, a minor fraction of Ga(I) sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS2014

Simultaneous Laser-induced Fluorescence of Nitric Oxide and Atomic Oxygen in the Hypersonic Materials Environment Test System Arcjet Facility

Simultaneous nitric oxide (NO) and atomic oxygen (O) laser induced fluorescence (LIF) experiments were performed in the Hypersonic Materials Environmental Test System (HYMETS) facility at the NASA Langley Research Center. The data serves as an experimental database for validation for chemical and thermal nonequilibrium models used in hypersonic flows. Measurements were taken over a wide range of stagnation enthalpies (6.7 - 18.5 MJ/kg) using an Earth atmosphere simulant with a composition of 75% N2, 20% O2, and 5% Ar (by volume). These are the first simultaneous measurements of NO and O LIF to be reported in literature for the HYMETS facility. The maximum O LIF mean signal intensity was observed at a stagnation enthalpy of approximately 12 MJ/kg while the maximum NO LIF mean signal intensity was observed at a stagnation enthalpy of 6.7 MJ/kg. Experimental results were compared to simple fluorescence model that assumes equilibrium conditions in the plenum and frozen chemistry in the isentropic nozzle expansion (Mach 5). The equilibrium calculations were performed using CANTERA v2.1.1 with 16 species. The fluorescence model captured the correlation in mean O and NO LIF signal intensities over the entire range of stagnation enthalpies tested. Very weak correlations between single-shot O and NO LIF intensities were observed in the experiments at all of the stagnation enthalpy conditions.

Johansen, Craig↗

DOE OSTI2020

Oxidation of 3D-printed SiC in air and steam environments

Here, the high-temperature oxidation of additively manufactured and chemically vapor infiltrated (3D-printed SiC) has been compared to chemical vapor deposited (CVD) SiC. 100-h isothermal exposures were conducted at 1425° and 1300°C at 1 atm under both dry air and steam environments. A SiC reaction tube was utilized to reduce silica volatility. After steam oxidation at 1425° and 1300°C, on the 3D-printed SiC surface, which was intrinsically rougher than the CVD surface, scales were 70%–90% thicker at the convex regions compared to concave/flat regions. In the convex regions, large cracks perpendicular to the oxidizing interface were observed. After dry air oxidation, scale thicknesses were comparable between 3D-printed SiC and CVD SiC, regardless of geometry. Finite element modeling, conducted to elucidate the relationship between SiC geometry and ß- to α-cristobalite transformation stress, determined cristobalite transformation tensile stresses to be on the order of 103 MPa during cool down, assuming a 6 vol% reduction. Compared to flat SiC substrates, tensile transformation stresses were elevated at concave regions and relaxed at convex regions. Combined with specimen mass gain (accounting for the rougher surface) of 3D-printed SiC being 15%–32% higher for 3D-printed SiC after 1300°C and 1425°C steam oxidation, the work presented concludes that the increased oxidation of 3D-printed SiC is primarily caused by tensile hoop stresses driven by oxidation volume expansion. Lastly, the efficacy of the 3D-printing method is demonstrated through the production of tristructural isotropic imbedded 3D-printed SiC fuel forms.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

First-principles insights into chromium-induced oxide phases in NiO

The high-temperature oxidation of Ni–Cr alloys leads to complex oxide scales comprising Ni(Cr)O solid solutions, NiCr 2 O 4 spinel, and Cr 2 O 3 corundum within the NiO matrix. Understanding the atomic-scale mechanisms of Cr segregation and precipitate formation is crucial for enhancing oxidation resistance. Here, we employ density functional theory calculations to investigate Cr behavior on NiO(100), (110), and (111) surfaces and in the bulk. Our results reveal that isolated Cr atoms preferentially segregate to the surfaces, stabilizing Ni(Cr)O solid solutions via strong Cr–O bonding, whereas Cr pairs and clusters favor subsurface migration and bulk aggregation, promoting nucleation of NiCr 2 O 4 and Cr 2 O 3 phases. These findings elucidate a size-dependent segregation mechanism linking Cr coordination environments to oxide phase evolution. This atomic-scale insight informs strategies to tailor oxide microstructures and enhance the high-temperature oxidation resistance of Ni–Cr alloys.

Chromium Segregation↗

DOE OSTI2020

Pretreatment Effects on the Surface Chemistry of Small Oxygenates on Molybdenum Trioxide

Understanding surface reactions of biomass-derived oxygenates on metal oxides is important for designing catalysts for valorization of biomass. As such, This work elucidated the effect of different pretreatments on molybdenum trioxide (MoO 3 ) to understand how surface reactivity is controlled by the surface oxidation state. The catalyst was pretreated in oxidative, inert, and reducing environments. The inert and reducing pretreatments created oxygen vacancies on the catalyst surface that acted as active sites for the adsorption of oxygenated molecules, with the reducing pretreatment yielding a higher density of these active sites. Exposing the catalyst to an alcoholic solvent such as methanol also led to a partial reduction similar to the inert pretreatment. After pretreatment, the catalyst was exposed to ethanol, acetaldehyde, and crotonaldehyde with subsequent characterization by diffuse reflectance infrared spectroscopy (DRIFTS), temperature-programmed desorption (TPD), X-ray absorption near edge spectroscopy (XANES), and X-ray photoelectron spectroscopy (XPS). Density functional theory (DFT) was also used to determine adsorption configurations and energies of ethanol, acetaldehyde, and crotonaldehyde. Reduced surfaces were shown to have a stronger affinity for carbonyls, leading to a higher activity for the aldol condensation of acetaldehyde and ethanol to C 4 molecules. Catalysts pretreated in an oxidative environment were completely inactive toward chemisorption and reaction of acetaldehyde.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Reevaluation of XPS Pt 4f peak fitting: Ti 3s plasmon peak interference and Pt metallic peak asymmetry in Pt@TiO2 system

The structural, electronic, and electrochemical properties of noble metals supported on transition metal oxides, such as Pt nanoparticles (NPs) supported on TiO2 (Pt@TiO2), have been extensively studied for their relevance to energy technologies, including photocatalysis, electrocatalysis, and electrochemical energy conversion. As the need to lower the amount of Pt and other noble metals used in energy conversion systems becomes urgent, it is essential to accurately quantify the loading of these metals and electronic density redistribution between them and their supports. X-ray photoelectron spectroscopy (XPS) is widely used for the identification and quantification of chemical species. In particular, fitting of the Pt 4f spectra for Pt@TiO2 is frequently performed to determine the chemical environment and oxidation state of Pt, which strongly affect the physical behavior and catalytic performance of this system. Here, we show that neglecting contributions due to the Pt surroundings and the asymmetry of the Pt metal peak in the line shape fitting can lead to severe mischaracterization of the oxidation state of Pt. We quantify the effects of background contributions that stem from the TiO2 support and discuss how factoring in the strong asymmetry of Pt 4f doublets, which stems from the shake-up type processes, affects the interpretation of Pt 4f XPS line shape.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Light- and Chemical-Doping-Induced Magnetic Behavior of Eu Molecular Systems

Variable temperature electron paramagnetic resonance (VT-EPR) was used to investigate the role of the environment and oxidation states of several coordinated Eu compounds. We find that while Eu(III) chelating complexes are diamagnetic, simple chemical reduction results in the formation of paramagnetic species. In agreement with the distorted D 3h symmetry of Eu molecular complexes investigated in this study, the EPR spectrum of reduced complexes showed axially symmetric signals (g ⊥ = 2.001 and g ∥ = 1.994) that were successfully simulated with two Eu isotopes with nuclear spin 5/2 ( 151 Eu and 153 Eu with 48% and 52% natural abundance, respectively) and nuclear g-factors 151 Eu/ 153 Eu = 2.27. Illumination of water-soluble complex Eu(dipic) 3 at 4 K led to the ligand-to-metal charge transfer (LMCT) that resulted in the formation of Eu(II) in a rhombic environment (g x = 2.006, g y = 1.995, g z = 1.988). The existence of LMCT affects the luminescence of Eu(dipic) 3 , and pre-reduction of the complex to Eu(II)(dipic) 3 reversibly reduces red luminescence with the appearance of a weak CT blue luminescence. Furthermore, encapsulation of a large portion of the dipic ligand with Cucurbit[7]uril, a pumpkin-shaped macrocycle, inhibited ligand-to-metal charge transfer, preventing the formation of Eu(II) upon illumination.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Predicting oxidation damage of ultra high-temperature carbide ceramics in extreme environments using machine learning

Determining the oxidation resistance of UHTC carbides in extreme environments is challenging theoretically and experimentally due to the high dimensional complexity of influencing variables and intricate testing setups. Herein we demonstrate the use of machine learning (ML) models trained with experimental literature data to predict the oxide thickness of UHTC carbides exposed to air based on composition, mean grain size, relative densification, holding time, and temperature. A multi-dimensional database with 76 occurrences is created containing experimental results of Hf, Zr, and Ta carbides plus additives. In this study, the preprocessed database is then used to train ML models to predict their oxidation behavior. The trained model predicts the oxidation damage in the form of an average oxide thickness in UHTC carbides with a Mean Absolute Error (MAE) of ±65.45 μm for samples in the testing set that developed thicknesses up to 1000 μm. The model successfully predicted oxidation damage for a recession rate lower than 60 μm/min. It is noticed that the ensemble method MAE is increased to ±134.34 μm while forecasting the oxidation of samples with a recession rate higher than the threshold. The unprecedented approach is a novel way to predict the damage through the oxidation of carbide compounds before processing for a smarter design with room for improvement.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Effect of Applied Stress on the Selective Oxidation of Alloy 600 Exposed to PWR Primary Water and Rhines Pack Environments

A mechanistic understanding of corrosion and oxidation processes is crucial to ensure long-term resistance to stress corrosion cracking of Ni-base structural alloys in pressurized water reactor (PWR) primary and secondary systems. Aqueous corrosion of Ni-base alloys under PWR primary water conditions was previously compared to gaseous oxidation with comparable oxygen potentials. However, those studies considered only stress-free conditions, which removes a critical parameter for understanding stress corrosion behaviors. A significant knowledge gap exists for the role of applied stresses on selective internal oxidation in gaseous environments. A micro-4-point-bend jig was designed to facilitate stress in a Rhines Pack set-up. Selective oxidation at different stress and strain conditions was investigated in a series of Rhines Pack experiments for Alloy 600. Focused ion beam milling enabled the extraction of site-specific specimens containing selected high-energy grain boundaries from tensile and compressive stress regions. Analytical transmission electron microscopy was employed to analyze the microstructure and chemical composition of the resulting oxides. Protective surface oxide films and selective intergranular oxides were observed at different conditions. The implications of these fundamental differences are discussed relative to intergranular attack and stress corrosion cracking mechanisms in PWR primary water.

stress, 4-point-bend, selective oxidation, Alloy 6↗

DOE OSTI2024

Metal–Organic Frameworks as a Tunable Platform to Deconvolute Stereoelectronic Effects on the Catalytic Activity of Thioanisole Oxidation

The local environment of a metal active site plays an important role in affecting catalytic activity and selectivity. In re-cent studies, tailoring the behavior of a molybdenum-based active site via modulation of the first coordination sphere has led to improved thioanisole oxidation performance, but disentangling electronic effects from steric influences that arise from these modifications is nontrivial, especially in heterogeneous systems. To this end, the tunability of metal–organic frameworks (MOFs) makes them promising scaffolds for controlling the coordination sphere of a heterogene-ous, catalytically-active metal site while offering additional, attractive features such as crystallinity and high porosity. Herein, we report a variety of MOF-supported Mo species, which were investigated for catalytic thioanisole oxidation to methyl phenyl sulfoxide and/or methyl phenyl sulfone using tert-butyl hydroperoxide (tBHP) as the oxidant. In particular, MOFs of contrasting node architectures were targeted, presenting a unique opportunity to investigate ste-reoelectronic control of Mo active sites in a systematic manner. A Zr 6 -based MOF, NU-1000, was employed along with its sulfated analog Zr 6 -based NU-1000-SO 4 to anchor a dioxymolybdenum species, which enabled examination of sup-port-mediated active site polarizability on catalytic performance. In addition, a MOF containing a mixed metal node, Mo-MFU-4l, was used to probe the stereoelectronic impact of an N-donor ligand environment on the catalytic activity of the transmetalated Mo center. Furthermore, characterization techniques including single crystal X-ray diffraction, were concomi-tantly used with reaction kinetic profiles to better comprehend the dynamics of different Mo active sites, thus correlat-ing structural change with activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗