Search NASA⌕ Search

SEARCH · Search NASA

Results for “particle fracture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Extrusion of Unhomogenized Castings of 7075 Aluminum via ShAPE

Extrusion of unhomogenized castings of 7075 aluminum (Al) alloy has been accomplished using shear assisted processing and extrusion (ShAPE). The simultaneous plastic deformation and heat generation during ShAPE rapidly fracture and dissolve interdendritic and intragranular secondary phases of Al-Zn-Mg-Cu, accomplishing homogenization in seconds rather than many hours in a furnace prior to extrusion. ShAPE thereby eliminates the energy-intensive and time-consuming homogenization step required to prepare as-cast microstructures for conventional extrusion. Concurrently, extensive grain refinement occurs due to gradient activation of dynamic recrystallization during ShAPE, which facilitates a threefold increase in extrusion speed compared to the conventional extrusion method. Evident enhancement of the mechanical properties of ShAPE+T6 samples is achieved, compared to the ASTM standard values for conventional extrusion products. The microstructural evolution pathway, involving the processes of grain refinement and secondary particle dissolution, is explained using scanning and transmission electron microscopy.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Atmospheric particle abundance and sea salt aerosol observations in the springtime Arctic: a focus on blowing snow and leads

Abstract. Sea salt aerosols play an important role in the radiation budget and atmospheric composition over the Arctic, where the climate is rapidly changing. Previous observational studies have shown that Arctic sea ice leads are an important source of sea salt aerosols, and modeling efforts have also proposed blowing snow sublimation as a source. In this study, size-resolved atmospheric particle number concentrations and chemical composition were measured at the Arctic coastal tundra site of Utqiaġvik, Alaska, during spring (3 April–7 May 2016). Blowing snow conditions were observed during 25 % of the 5-week study period and were overpredicted by a commonly used blowing snow parameterization based solely on wind speed and temperature. Throughout the study, open leads were present locally. During periods when blowing snow was observed, significant increases in the number concentrations of 0.01–0.06 µm particles (factor of 6, on average) and 0.06–0.3 µm particles (67 %, on average) and a significant decrease (82 %, on average) in 1–4 µm particles were observed compared to low wind speed periods. These size distribution changes were likely caused by the generation of ultrafine particles from leads and/or blowing snow, with scavenging of supermicron particles by blowing snow. At elevated wind speeds, both submicron and supermicron sodium and chloride mass concentrations were enhanced, consistent with wind-dependent local sea salt aerosol production. At moderate wind speeds below the threshold for blowing snow as well as during observed blowing snow, individual sea spray aerosol particles were measured. These individual salt particles were enriched in calcium relative to sodium in seawater due to the binding of this divalent cation with organic matter in the sea surface microlayer and subsequent enrichment during seawater bubble bursting. The chemical composition of the surface snowpack also showed contributions from sea spray aerosol deposition. Overall, these results show the contribution of sea spray aerosol production from leads on both aerosols and the surface snowpack. Therefore, if blowing snow sublimation contributed to the observed sea salt aerosol, the snow being sublimated would have been impacted by sea spray aerosol deposition rather than upward brine migration through the snowpack. Sea spray aerosol production from leads is expected to increase, with thinning and fracturing of sea ice in the rapidly warming Arctic.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Stochastic Modeling in a Multimaterial Continuum Mixture Shock Physics Code

Stochastic modelling approaches are presented to capture random effects at multiple time and length scales. Random processes that occur at the microscale produce nondeterministic effects at the macroscale. Here we present three stochastic modeling approaches that describe random processes at microscopic length scales and map these processes to the macroscopic length scale. The first stochastic modeling approach is based upon a particle based numerical technique to solve a Stochastic Differential Equation (SDE) using an arbitrary diffusion process to capture random processes at the microstructural level. The second approach prescribes a Probability Density Function (PDF) for the drift and diffusion of the random variable derived using the forward and backward Kolmogorov equations. This method requires mean and drift evolution PDF transport equations. The third approach is the coupling of multiple random variables which are dependent on each other. The relationship of the PDFs and a coupling function, known as a copula, produces a Joint Probability Density Function (JPDF). These stochastic modeling approaches are implemented into a Multiple Component (MC) shock physics computational code and used to model statistical fracture and reactive flow applications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Discrete element model for powder grain interactions under high compressive stress

A reduced order, nonlocal model is proposed for the contact force between initially spherical particles under compression. The model in effect provides the normal component of the interaction force between elements in the discrete element method (DEM). It is applicable to high relative density and large stress in powder compaction. It takes into account the mutual interaction between multiple points of contact, in contrast to the usual assumption in DEM of pair interactions. The mathematical form of the model is derived from a variational formulation that leads to the momentum balance for the forces on each grain. The model is calibrated mainly using detailed three dimensional peridynamic simulations of single grains under compressive loading by rigid plates that move radially with prescribed velocity. This calibration takes into account the large deformation and fracture of the grains. The interaction model also includes terms for the unloading behavior and adhesion. Finally, as validation, the model is applied to test data on the compaction of microcrystalline cellulose bulk powder.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mechanically robust high magnetic-performance Sm-Co sintered magnets through microstructure engineering

Samarium-cobalt (Sm-Co) sintered magnets have high magnetic energy densities, great resistance to demagnetization and corrosion, and excellent thermal stability in a wide temperature range (–50–550 °C). However, the utilization of these magnets is restricted by their brittleness. Based on micromechanical and the Zener pinning model, Sm-Co sintered magnets with improved mechanical properties have been designed and fabricated via microstructure engineering. A small amount of fine Sm 2 O 3 particulates (0–3 wt%) has been incorporated into Sm 2 (CoFeCuZr) 17 sintered magnets to refine the grain size by up to approximately 50% (from 45 to 22 µm) and narrow the grain size distribution. Doping with 3 wt% Sm 2 O 3 increased the flexural strength by 62% while maintaining magnetic performance. Both grain-refined unimodal microstructure and heterogeneous laminated coarse/fine grain microstructure were formed by strategically designed assemblies of Sm 2 O 3 -added Sm-Co powder feedstock mixtures. The technology is compatible with existing magnet manufacturing processes. Numerical micromechanics simulation indicates that the fracture is dominated by intragranular mode. The mechanical strength is mainly enhanced by the additive-induced grain refinement, while the small amount of Sm 2 O 3 addition has a small direct positive contribution. Finally, these magnets will be more cost-effective, efficient, and robust for various functional applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A hybrid finite volume method and smoothed particle hydrodynamics approach for efficient and accurate blast simulations

Modeling strong shock waves in fluids remains a persistent challenge in computational physics. Essential to research efforts in industry and defense, numerous methods have been devised to improve the accuracy and efficiency of shock simulations. A novel, hybrid Finite Volume Method (FVM)-Smoothed Particle Hydrodynamics (SPH) approach is capable of further improving efficiency and retaining accuracy by exploiting the favorable characteristics of each respective method. This hybrid approach is presented for shock capturing in compressible fluids. The Python framework Pyro2 is employed to simulate a coarse FVM mesh, while the Python framework PySPH is utilized to model the fluid in regions with high gradients through SPH particles. The performance of the hybrid FVM-SPH scheme, compared to the individual FVM and SPH methods, is assessed in 1 kt and 10 kt blast simulations. Our results indicate that the hybrid approach offers higher computational efficiency than SPH while preserving its accuracy and characteristics. The hybrid approach had a relative speedup of 11.3x and 22.3x over the FVM and SPH approaches for the 1 kt simulation and a relative speedup of 14.7x and 20.9x over the FVM and SPH approaches for the 10 kt simulation. The hybrid SPH algorithm enables future compressible fluid simulations with more extensive capabilities than grid-based methods alone, presenting potential applications in modeling fluid-structure interactions and solid deformation and fracturing in blast simulations.

Myers, Conner↗
DOE OSTI2022

Understanding Phase and Interfacial Effects of Spall Fracture in Additively Manufactured Ti-5Al-5V-5Mo-3Cr

Additive manufactured Ti-5Al-5V-5Mo-3Cr (Ti-5553) is being considered as an AM repair material for engineering applications because of its superior strength properties compared to other titanium alloys. Here, we describe the failure mechanisms observed through computed tomography, electron backscatter diffraction (EBSD), and scanning electron microscopy (SEM) of spall damage as a result of tensile failure in as-built and annealed Ti-5553. We also investigate the phase stability in native powder, as-built and annealed Ti-5553 through diamond anvil cell (DAC) and ramp compression experiments. We then explore the effect of tensile loading on a sample containing an interface between a Ti-6Al-V4 (Ti-64) baseplate and additively manufactured Ti-5553 layer. Post-mortem materials characterization showed spallation occurred in regions of initial porosity and the interface provides a nucleation site for spall damage below the spall strength of Ti-5553. Preliminary peridynamics modeling of the dynamic experiments is described. Finally, we discuss further development of Stochastic Parallel PARticle Kinteic Simulator (SPPARKS) Monte Carlo (MC) capabilities to include the integration of alpha (α)-phase and microstructural simulations for this multiphase titanium alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Perspectives and challenges of ultra-high temperature ceramics for fusion plasma-facing applications

Ultra-high temperature ceramics (UHTCs) offer several potential advantages as plasma-facing components (PFCs) in fusion reactors due to their extreme melting points, tailorable thermal conductivity, and attractive unirradiated mechanical properties including fracture toughness comparable or superior to tungsten. Here, recent developments and material properties of UHTCs are briefly reviewed, along with an overview of limited studies on their responses to neutron irradiation and an evaluation of plasma-surface interactions. Five key research pathways, primarily focused on irradiation effects, for advancing UHTCs in PFC applications are discussed: (1) assessing irradiation effects on the coupled thermal–mechanical performance (2) addressing the lack of studies on irradiation, plasma-surface interactions, and their synergistic effects; (3) investigating high-temperature (>1000 °C) neutron irradiation effects critical for PFC performance; (4) optimizing multi-component UHTC compositions or composites to improve thermal or mechanical properties; (5) enhancing radiation resistance to mitigate microcracking and void swelling through strategies such as increasing sink strength by reducing grain size, introducing fine particles, and leveraging complex concentrated alloy concepts.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The combined effects of hydrogen and aging condition on the deformation and fracture behavior of a precipitation-hardened nickel-base superalloy

The effect of hydrogen (H) on the deformation behavior of Monel K-500 in various isothermal heat treatment conditions (non-aged, under-aged, peak-aged, and over-aged) was assessed via uniaxial mechanical testing. H-charged and non-charged specimens were strained to failure to facilitate a comparison of ductility, fracture surface morphology, strength, and work hardening behavior. For all examined heat treatment conditions, H charging leads to a significant reduction in ductility, which is accompanied by a consistent change in fracture surface morphology from ductile microvoid coalescence to brittle intergranular fracture. While H charging led to a systematic enhancement in the yield strength of all heat treatments, the three age-hardened conditions exhibited a more than 2-fold increase relative to the non-aged heat treatment. This suggests that H modifies the dislocation–precipitate interactions, which also manifest themselves through changes in work hardening metrics related to the dislocation storage and recovery rates. In particular, the H-charged peak-aged specimen exhibited a significant increase in initial hardening (dislocation storage) rate relative to the H-charged under-aged specimen. Transmission electron microscopy of these samples revealed the onset of widespread dislocation looping in the H-charged peak-aged sample, in addition to the planar slip bands characteristic of the non-charged condition. This result suggests that hydrogen induces the particle shearing-to-looping transition at smaller particle sizes. Possible mechanistic explanations for this observed behavior are presented.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Development of Next Generation Hierarchical Hybrid Cu-Si anode Batteries via Direct-Ink Writing Application: End of (6th) Month Report - November 2025

Sustainable renewable energy continues to be in dire need to effectively combat global warming. Emerging technology for electric vehicles/ devices remains in high demand that is not only lower in cost, more efficient, but safer in comparison to commercial materials on the market. Although first-generation lithium-ion batteries have exhibited extensive commercial application, conventional graphite no longer meets this increasing demand as an efficient anode material. Due to the fact that graphite has a subpar theoretical specific capacity (372 mAh g -1 ), thus significant limitations in rate capability (for potential faster charging at higher C-rates currently commercially available.). Alternatively, silicon has gained significant attention as a superior candidate to potentially surpass graphite. Due to silicon’s exceedingly high theoretical capacity (4,200 mAh g -1 ) in comparison to standard graphite, its abundance thus in turn it’s low-cost, in addition to exhibiting a significantly low working potential (< 0.4 V vs Li/Li + ). However, one of the main (and most detrimental) challenges is silicon’s tendency to expand in volume (> 300%) upon discharge as it begins the lithiation process. As a direct result, it causes not only for the particles to both crack and pulverize under mechanical stress as the volume continues to expand and contract during cycling. Upon assembling the cell, it needs to undergo ‘charging’ for initially discharging/ ‘activating’ the cell, otherwise commonly known as the ‘formation’ step. As a result a solid electrolyte interface (SEI) layer begins to form at the anode surface because some of the electrolyte begins to react during the formation process. However, this (SEI) layer is deemed as a ‘protective’ interlayer because in theory it prevents further reaction as the cell continues to cycle. However, due to the volume change it causes significant degradation at the interface. As cracking starts to occur at the anode surface, it results in a ‘new’ altered surface with each cycle that causes further reaction with the electrolyte as a byproduct quickly consuming active Li/ and more electrolyte. Thus, fracturing this ‘protective layer,’ causing significantly higher impedance as a result, and in turn a decline in capacity due to active Li-loss. In addition to the active material exfoliating off from the current collector, further contributing to the steady decline in capacity and overall performance. Current state of the art Si-anode batteries on the market range between a maximum content of 5-10 Si wt%. It has been previously reported Tesla has utilized SiO x -C anodes containing 5 wt% Si within their ‘Model 3/ Model X’ electric vehicles. However, more recent ‘Model 3’ vehicles have started to incorporate 10 Si wt%, in which they were able to increase their energy density upwards by approximately 30%. Recent effort has been focused on continuing to increase the wt% of Si being utilized, eventually to 100 wt% of Si, to maximize the energy density even further.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Marine aerosol generation experiments in the High Arctic during summertime

The rapidly warming Arctic has transitioned to thinner sea ice which fractures, producing leads. Few studies have investigated Arctic sea spray aerosol (SSA) produced from open ocean, leads, and melt ponds, which vary in salinity and organic and microbial community composition. A marine aerosol reference tank was deployed aboard an icebreaker to the Arctic Ocean during August–September 2018 to study SSA generated from locally collected surface waters. Aerosol generation experiments were carried out using water collected from the marginal ice zone, a human-made hole in sea ice near the North Pole, and both lead and melt pond water during an ice floe drift period. Salinity, chlorophyll a, organic carbon, nitrogen, and microbial community composition were measured. Eukaryotic plankton and bacterial abundance were elevated in experimental water from the marginal ice zone, but the relative contributions from major eukaryotic taxonomic groups varied little across the experiments. The chemical composition of individual SSA particles was analyzed using Raman microspectroscopy and computer-controlled scanning electron microscopy with energy-dispersive X-ray spectroscopy. Individual sea salt aerosol, primary organic aerosol, and mineral dust particles were observed. Sea salt aerosol constituted 44–95% of individual submicrometer and 68–100% of supermicrometer particles, by number, generated during each experiment. Carbon was detected in 85%, by number, of the individual sea salt particles, with visible organic coatings. Carbohydrates were detected in 72% of particles, by number, with smaller contributions from long-chain fatty acids (13%) and siliceous material (15%). SSA generated from melt pond water contained only long-chain fatty acids and siliceous material. Quantification of the ice-nucleating activity showed that locally produced SSA may define the High Arctic background ice-nucleating particle population, but cannot account for the peak atmospheric concentrations observed. As the Arctic warms, the increasing SSA emissions have a complex dependence on changing biological and physical processes.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Stress and Strain Heterogeneity and Persistence in Uniaxially‐ and Triaxially‐Loaded Sandstone

Two critical questions in brittle rock mechanics are how rocks developed localized strains and to what extent internal stress heterogeneity controls this localization and subsequent macroscopic failure. Definitive answers have not yet been found, but would provide insight into rock fracture mechanics as relevant to hydrocarbon extraction and sequestration. Here, we use synchrotron X‐ray tomography (XRT) and 3D X‐ray diffraction (3DXRD) during uniaxial and triaxial tests on Nugget and Bentheimer sandstones to examine strain and stress localization prior to mechanical failure. 3DXRD was used to measure intra‐granular lattice strains which were used to compute elastic stress tensors of each grain. Digital volume correlation (DVC) was applied to XRT images to determine the strain field in the sample. Both samples featured marked spatial heterogeneity, localization, and temporal persistence of elevated stresses and strains during their mechanical deformation toward failure. Both samples featured a majority of grains with at least one principal stress component that was tensile, a signature of the influence of heterogeneity on stress transmission. Measurements further revealed that compressive stress orientations and statistics evolved in a similar manner to those of inter‐particle forces in loose granular materials, with triaxially‐compressed rock exhibiting enhanced grain stress heterogeneity compared to uniaxially‐compressed rock. Our results complement recent work by others who employed XRT and scanning 3DXRD to study triaxially‐compressed sandstone, but extend those results to uniaxial compression, sandstones of varied porosity, and grain stress measurements throughout the 3D full extent of the samples rather than in a single layer examined with scanning 3DXRD.

58 GEOSCIENCES↗
DOE OSTI2023

Environmental impact of solution pH on the formation and migration of iron colloids in deep subsurface energy systems

Deep subsurface stimulation processes often promote fluid-rock interactions that can lead to the formation of small colloidal particles that are suspected to migrate through the rock matrix, partially or fully clog pores and microfractures, and promote the mobilization of contaminants. Thus, the goal of this work is to understand the geochemical changes of the host rock in response to reservoir stimulation that promote the formation and migration of colloids. Two different carbonate-rich shales were exposed to different solution pHs (pH = 2 and 7). In this study, iron and other mineral transformations at the shale-fluid interface were first characterized by synchrotron-based XRF mapping. Then, colloids that were able to migrate from the shale into the bulk fluid were characterized by synchrotron-based extended X-ray absorption structure (EXAFS), scanning electron microscopy (SEM), and single-particle inductively coupled plasma time-of-flight mass spectrometry (sp-icpTOF-MS). When exposed to the pH = 2 solution, extensive mineral dissolution and secondary precipitation was observed; iron-(oxyhydr)oxide colloids colocated with silicates were observed by SEM at the fluid-shale interfaces, and the mobilization of chromium and nickel with these iron colloids into the bulk fluid was detected by sp-icpTOF-MS. Iron EXAFS spectra of the solution at the shale-fluid interface suggests the rapid (within minutes) formation of ferrihydrite-like nanoparticles. Thus, we demonstrate that the pH neutralization promotes the mobilization of existing silicate minerals and the rapid formation of new iron colloids. These Fe colloids have the potential to migrate through the shale matrix and mobilize other heavy metals (such as Cr and Ni, in this study) and impacting groundwater quality, as well produced waters from these hydraulic fracturing operations.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2019

Modeling reactivity insertion experiments of TRISO particles in NSRR using BISON

This research presents BISON simulations of stress, temperature, and failure probability of tristructural isotropic (TRISO) fuel particles subjected to transient power pulse conditions in the Nuclear Safety Research Reactor (NSRR). We report that by modifying the default elastic properties of the PyC and the UO 2 coefficient of thermal expansion correlation, BISON was found to produce suitable agreement with the observed and independently simulated results when appropriate shape and scale Weibull parameters for SiC failure were chosen. The Weibull parameter effects were also explored within the range of SiC failure and were applied using experimental data from hemispherical crush testing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Radionuclide Screening Analysis and Transport Parameters for Pahute Mesa Detonations, Nevada National Security Site

A “screening analysis” is implemented at Pahute Mesa (PM), Nevada National Security Site (NNSS), to determine subsets of the 43 radionuclides listed in the radionuclide inventory of Finnegan et al. (2016) that are of relevance or potential relevance to the hydrologic source term (HST) for assessment of radionuclide transport in groundwater. Consideration is added to how levels of contamination are defined and whether any other radionuclides not in the inventory are relevant to the HST. A model is developed to estimate a range of possible source concentrations in groundwater that account for uncertainty in partitioning into melt glass and sorption into surrounding rock of the exchange zone for the 82 PM underground nuclear tests detonated in vertical shafts. The model also accounts for the varied hydrogeochemical settings. Transport parameters needed for the screening model calculations are developed from databases for hydrogeologic units, chemistry, mineralogy, fracture spacing, fracture aperture, fracture openness, matrix porosity, bulk density, saturation, and alteration. Of key importance is consideration of diagenetic zonation of the mineralogy related to hydrothermal alteration. The screening analysis compares model results with available groundwater radiochemistry data. Consistency between screening model results and available data helps validate the model for application to all 43 radionuclides, most of which have no measurements or only non-detect measurements of concentration in groundwater. The screening analysis determines that ten radionuclides – tritium, Sr-90, I-129, Cs-137, U-232, U-233, U-234, U-238, and the total of Pu-239 and Pu-240 are relevant to the HST. Determination of relevance is primarily based on data and/or model results indicating source concentration exceeding a maximum contaminant level (MCL) out to 100 years since the time of detonation. U-238 is relevant to assessment of contamination relative to MCLs for uranium and gross alpha particle activity. Five other radionuclides – C-14, Cl-36, Tc-99, Np-237, and Pu-238 – are determined potentially relevant to the HST based on a 0.1 MCL threshold. The screening analysis recommends additional attention to the natural daughter radionuclides of the uranium series (U-238) and thorium series (Th-232) decay chains, particularly Ra-226 and Ra-228, that were not included the inventory.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2023

A subdivision-stabilized B-spline mixed material point method

Subjected to external loadings, polymeric materials, e.g., biological tissues, hydrogels, and elastomers, may undergo extreme, nearly incompressible, (self-)contact deformations. For numerical modeling employing mesh-based techniques such as the finite element method (FEM), these deformations pose significant challenges due to large distortions in the deformed geometry, accuracy issues stemming from volumetric locking effects, and increased computational cost from complex contact searches. As an alternative to mesh-based methods, the material point method (MPM), a continuum-based particle technique, is gaining attention for its ability to handle extreme distortions and capture no-slip contact without added cost. For nearly incompressible material behaviors, while mixed formulations can address locking effects by treating displacements and pressure as independent fields, they can suffer from numerical instabilities close to the incompressibility limit due to the violation of the inf-sup condition, leading to inaccurate nodal pressure solutions. Here we propose an efficient and stable mixed B-spline material point method with highest achievable regularity for quasi-compressible polymeric materials. Using the two-scale relation of B-splines, we introduce a subdivision-stabilization for the two-field mixed MPM and obtain numerically stable, oscillation-free nodal solutions with equal-order interpolations with optimal regularity. Building on the Eulerian-Lagrangian nature of MPM, a previously-converged solution framework is adopted to mitigate issues related to cell-crossing and numerical fracture artifact present in standard MPM. We assess the stability and accuracy of the developed mixed MPM at large deformations for soft materials through the benchmark Cook’s membrane problem. Additionally, we test the robustness of the proposed MPM by modeling several examples, including the compression and indentation of a circular block into a quasi-compressible substrate and the twisting deformation of a rectangular block. The findings demonstrate the MPM’s capabilities for modeling practical soft material applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Production of Readily Compressible Dies for the Enhanced Sintering of Solids (PRESS) Preliminary Investigations

Non-oxide ceramics, which consist of predominantly carbides, borides, and nitrides, are of great interest to modern engineering because of their resistance to extreme conditions. Properties of such materials include high temperature resistance, high hardness, chemical resistance, and high fracture toughness. However, the main method for manufacturing parts of these materials is by machining cylindrical billets to the desired geometry. Not only does this produce waste, but the cost of machining is high since the part materials are of such high hardness. This method is used because these non-oxide ceramics must be sintered to high density using simultaneous heat and pressure within a hot-pressing unit. These units are inherently restricted to cylindrical geometries. A proposed way to expand the capabilities of a hot-press is by using intermediate compressible dies. This method consists of surrounding a ceramic part green body with a material that will shrink at the same rate as the part and survive the hot-pressing conditions. At the end, the compressible die material would be removed leaving a nearly net shaped hot-pressed part. In this study, graphite powder was investigated as the compressible die material with its shrinkage rate being controlled by particle size mixing. Both ceramic materials and graphite were then cast into parts and compressible dies respectively to show the feasibility of the compressible die hot-pressing method.

36 MATERIALS SCIENCE↗