Search NASA⌕ Search

SEARCH · Search NASA

Results for “performance improvements”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

A pattern synthesis technique for array feeds to improve radiation performance of large distorted reflector antennas

Technologies exist for construction of antennas with adaptive surfaces that can compensate for many of the larger distortions caused by thermal and gravitational forces. However, as the frequency and size of the reflectors increase, the subtle surface errors become significant and degrade the overall electromagnetic performance. Electronic compensation through an adaptive feed array offers a means for mitigation of surface distortion effects. A pattern synthesis approach for electromagnetic compensation of surface error is presented. The pattern synthesis approach uses a localized algorithm in which pattern corrections are directed toward specific portions of the pattern requiring improvement. The pattern synthesis technique uses radiation pattern data to perform the compensation.

Smith, William T.↗
NASA NTRS1996

Improved Saturation Performance in High Speed Waveguide Photodetectors at 1.3 ??sing an Asymmetric InA1GaAs/InGaAsP Structure

Waveguide photodetector (WGPD) results have recently been presented demonstrating the very large bandwidth-efficiency product potential of these devices. Improved saturation and linearity characteristics are realized in waveguide p-i-n photodetectors at 1.3 ??y using an asymmetric cladding structure with InA1GaAs/InGaAsP in the anode and InGaAsP in the cathode.

multi-mode structures photocurrent saturation wave↗
NASA NTRS1986

System structural test results - Six PODS III supports

Passive orbital disconnect struts can potentially reduce the support conductance a factor of 10 over state-of-the-art tension band nondisconnect supports and cut helium dewar weights in half for the same lifetime. A series of thermal and structural tests were performed to verify that this performance improvement is real. Structural tests on a PODS-III support system (consisting of six struts) is reported here. The results show the predicted performance improvements can be achieved and the PODS-III supports are ready for flight applications. For large tankage systems requiring higher side load capability, a PODS-IV version is currently being developed.

Parmley, Richard T.↗
NASA NTRS1999

I/O Parallelization for the Goddard Earth Observing System Data Assimilation System (GEOS DAS)

The National Aeronautics and Space Administration (NASA) Data Assimilation Office (DAO) at the Goddard Space Flight Center (GSFC) has developed the GEOS DAS, a data assimilation system that provides production support for NASA missions and will support NASA's Earth Observing System (EOS) in the coming years. The DAO's support of the EOS project along with the requirement of producing long-term reanalysis datasets with an unvarying system levy a large I/O burden on the future system. The DAO has been involved in prototyping parallel implementations of the GEOS DAS for a number of years and is now converting the production version from shared-memory parallelism to distributed-memory parallelism using the portable Message-Passing Interface (MPI). If the MPI-based GEOS DAS is to meet these production requirements, we must make I/O from the parallel system efficient. We have designed a scheme that allows efficient I/O processing while retaining portability, reducing the need for post-processing, and producing data formats that are required by our users, both internal and external. The first phase of the GEOS DAS Parallel I/O System (GPIOS) will expand upon the common method of gathering global data to a Single PE for output. Instead of using a PE also tasked with primary computation, a number of PEs will be dedicated to I/O and its related tasks. This allows the data transformations and formatting required prior to output to take place asynchronously with respect to the GEOS DAS assimilation cycle, improving performance and generating output data sets in a format convenient for our users. I/O PEs can be added as needed to handle larger data volumes or to meet user file specifications. We will show I/O performance results from a prototype MPI GCM integrated with GPIOS. Phase two of GPIOS development will examine ways of integrating new software technologies to further improve performance and build scalability into the system. The maturing of MPI-IO implementations and other supporting libraries such as parallel HDF should provide performance gains while retaining portability.

Lucchesi, R.↗
NASA NTRS1982

Measured performance of a tip-controlled, teetered rotor with an NACA 64 sub 3-618 tip airfoil

Tests were conducted on the Mod-O 100 kW Wind Turbine to determine the performance of a tip-controlled rotor having an NACA 64 sub-618 airfoil over the moveable outboard 30% of the blade, while operating at nominal rotor speeds of 21 and 31 rpm. Tests were conducted at two rotor speeds to assess the performance improvement which could be realized with 2-speed operation. Test data are compared with analytical predictions and concluding remarks are presented. The results indicate a clear performance improvement for the 2-speed operation.

Corrigan, R. D.↗
NASA NTRS2019

Potential Weight Benefits of IM7/8552 Hybrid Thin-Ply Composites for Aircraft Structures

Composite materials have increasingly been used for aerospace applications due to improved performance and reduced weight compared to their metallic counterparts. Inclusion of thin-ply material, plies with cured thickness half or less than standard-ply composites, have potential to improve performance and reduce structural weight further. The effect of thin-ply material on the weight of aircraft structure was investigated by examining wing cover weight reduction. To minimize the effects on manufacturing due to using thin plies, hybrid laminates were examined that used thin ±45-degree plies to replace their standard-ply counterparts in laminates. Compression after impact (CAI) tests were conducted to examine the possible weight savings that could be gained by increasing the design allowables that were used to size the wing upper cover of a semi-span test article. A large increase in CAI strength was observed for quasi-isotropic hybrid laminates, whereas less improvement was seen for hard hybrid laminates such as found in the wing cover. For laminates design by CAI strength, weight savings of about 13% were found using the hybrid hard laminates compared to the standard-ply laminates. Whether similar weight savings could be expected for structure sized using tension after impact allowables will have to be investigated further. Notched specimens were tested to examine possible weight savings using hybrid laminates in regions that are sized using discrete source damage requirements. As expected, the hybrid laminate had marginal improvements over the standard-ply laminate for compression with a notch present. The hybrid laminate, however, exhibited about 20% lower strength than the standard-ply laminate counterpart for tension with a notch. The failure mode of the hybrid specimens was a brittle, self-similar crack, which differs from the standard-ply specimens that failed by significant amounts of delamination and fiber splitting. In light of the apparent reduction in notched tensile strength, additional investigation is required to assess the use of hybrid laminates for areas containing discrete source damage, and their effect on weight of such regions.

Lovejoy, Andrew E.↗
NASA NTRS1987

Large-scale static investigation of circulation-control-wing concepts applied to upper surface-blowing aircraft

The use of a circulation control to deflect turbofan engine thrust beyond 90 deg. has been proven in full-scale static ground tests of the circulation-control-wing/upper-surface-blowing (CCW/USB) concept. This powered high-lift system employs a circular, blown trailing edge to replace the USB mechanical flaps to entrain engine-exhaust flow, and to obtain both a vertical-thrust component and an augmented circulation lift for short takeoff and landing (STOL) applications. Previous tests (Phase 1), done in 1982, of a basic configuration installed on the Quiet Short Haul Research Aircraft confirmed these CCW/USB systems capabilities. A second phase (Phase 2) of full-scale, static, thrust-deflection investigations has reconfirmed the ability to deflect engine thrust from 40 to 102 deg., depending on thrust level. Five new configurations were evaluated and performance improvements noted for those configurations with larger blown span, fences or favorable engine interactions, smaller slot height, and larger radii with less than 180 deg. of CCW surface arc. In general, a 90 deg. circular arc with a smaller slot height provided the best performance, demonstrating that adequate thrust turning can be produced by a trailing-edge shape which may have minimal cruise-performance penalty. Thrust deflections were achieved at considerably lower blowing momentum than was required for the baseline case of Phase 1. Improved performance and versatility were thus confirmed for the CCW/USB system applied to STOL aircraft, where the potential for developing a non-moving-parts pneumatic thrust deflector to rapidly vary horizontal force from thrust to drag, while maintaining constant vertical force, appears quite promising. The conversion from high-lift to lower-drag cruise mode by merely terminating the blowing provides an effective STOL aircraft system.

Shovlin, M. D.↗
NASA NTRS2015

Advanced Bayesian Method for Planetary Surface Navigation

Autonomous Exploration, Inc., has developed an advanced Bayesian statistical inference method that leverages current computing technology to produce a highly accurate surface navigation system. The method combines dense stereo vision and high-speed optical flow to implement visual odometry (VO) to track faster rover movements. The Bayesian VO technique improves performance by using all image information rather than corner features only. The method determines what can be learned from each image pixel and weighs the information accordingly. This capability improves performance in shadowed areas that yield only low-contrast images. The error characteristics of the visual processing are complementary to those of a low-cost inertial measurement unit (IMU), so the combination of the two capabilities provides highly accurate navigation. The method increases NASA mission productivity by enabling faster rover speed and accuracy. On Earth, the technology will permit operation of robots and autonomous vehicles in areas where the Global Positioning System (GPS) is degraded or unavailable.

Center, Julian↗
NASA NTRS2007

Reconfigurable Control with Neural Network Augmentation for a Modified F-15 Aircraft

This paper describes the performance of a simplified dynamic inversion controller with neural network supplementation. This 6 DOF (Degree-of-Freedom) simulation study focuses on the results with and without adaptation of neural networks using a simulation of the NASA modified F-15 which has canards. One area of interest is the performance of a simulated surface failure while attempting to minimize the inertial cross coupling effect of a [B] matrix failure (a control derivative anomaly associated with a jammed or missing control surface). Another area of interest and presented is simulated aerodynamic failures ([A] matrix) such as a canard failure. The controller uses explicit models to produce desired angular rate commands. The dynamic inversion calculates the necessary surface commands to achieve the desired rates. The simplified dynamic inversion uses approximate short period and roll axis dynamics. Initial results indicated that the transient response for a [B] matrix failure using a Neural Network (NN) improved the control behavior when compared to not using a neural network for a given failure, However, further evaluation of the controller was comparable, with objections io the cross coupling effects (after changes were made to the controller). This paper describes the methods employed to reduce the cross coupling effect and maintain adequate tracking errors. The IA] matrix failure results show that control of the aircraft without adaptation is more difficult [leas damped) than with active neural networks, Simulation results show Neural Network augmentation of the controller improves performance in terms of backing error and cross coupling reduction and improved performance with aerodynamic-type failures.

Burken, John J.↗
NASA NTRS1979

Effect of outboard vertical-fin position and orientation on the low-speed aerodynamic performance of highly swept wings

A theoretical study was conducted to determine the potential low-speed performance improvements which can be achieved by altering the position and orientation of the outboard vertical fins of low-aspect-ratio highly swept wings. Results show that the magnitude of the performance improvements is solely a function of the span-load distribution. Both the vertical-fin-chordwise position and toe angle provided effective means for adjusting the overall span-load distribution.

Johnson, V. S.↗
NASA NTRS1992

Full-scale transmission testing to evaluate advanced lubricants

Experimental tests were performed on the OH-58A helicopter main rotor transmission in the NASA Lewis 500 hp helicopter transmission test stand. The testing was part of a lubrication program. The objectives are to develop and show a separate lubricant for gearboxes with improved performance in life and load carrying capacity. The goal was to develop a testing procedure to fail certain transmission components using a MIL-L-23699 based reference oil and then to run identical tests with improved lubricants and show improved performance. The tests were directed at parts that failed due to marginal lubrication from Navy field experience. These failures included mast shaft bearing micropitting, sun gear and planet bearing fatigue, and spiral bevel gear scoring. A variety of tests were performed and over 900 hrs of total run time accumulated for these tests. Some success was achieved in developing a testing procedure to produce sun gear and planet bearing fatigue failures. Only marginal success was achieved in producing mast shaft bearing micropitting and spiral bevel gear scoring.

Lewicki, David G.↗
NASA NTRS2006

Aerodynamic Performance Measurements for a Forward Swept Low Noise Fan

One source of noise in high tip speed turbofan engines, caused by shocks, is called multiple pure tone noise (MPT's). A new fan, called the Quiet High Speed Fan (QHSF), showed reduced noise over the part speed operating range, which includes MPT's. The QHSF showed improved performance in most respects relative to a baseline fan; however, a partspeed instability discovered during testing reduced the operating range below acceptable limits. The measured QHSF adiabatic efficiency on the fixed nozzle acoustic operating line was 85.1 percent and the baseline fan 82.9 percent, a 2.2 percent improvement. The operating line pressure rise at design point rotational speed and mass flow was 1.764 and 1.755 for the QHSF and baseline fan, respectively. Weight flow at design point speed was 98.28 lbm/sec for the QHSF and 97.97 lbm/sec for the baseline fan. The operability margin for the QHSF approached 0 percent at the 75 percent speed operating condition. The baseline fan maintained sufficient margin throughout the operating range as expected. Based on the stage aerodynamic measurements, this concept shows promise for improved performance over current technology if the operability limitations can be solved.

Fite, E. Brian↗
NASA NTRSDate not supplied

Voxel Based Three-Dimensional Topology Optimization of Heat Exchanger Fins

Increasing interest in novel aircraft propulsion systems and potential for unwanted heat generation, or capture and reuse of waste heat, may require increasingly lightweight and high performing heat exchangers. Advances in manufacturing technologies have shown potential to create complex designs, but design tools need more flexibility. This study utilizes genetic algorithm-driven topology optimization to develop high performance heat exchanger fins for critical applications such as aerospace. The solid domain is generated using voxel representation where a voxel value of 1 indicates the solid domain and a voxel value of 0 refers to the fluid domain. The use of voxel representation somewhat matches the digitization of a model that is required to fabricate using additive manufacturing, and also allows for a highly unconstrained geometry. To test the topology optimization approach, a three-dimensional(3D)baseline offset strip fin geometry in steady laminar flow(Reynolds number = 215)with conjugate heat transfer(simultaneous solution of solid and fluid temperature fields)is optimized. New designs are generated using the genetic algorithm (GA) and sent to evaluation by the CFD software OpenFOAM; then the GA sorts and selects the reproduction pool for the following generation. This process is repeated for 60 generations. The study also investigates the effect off in material on the performance of the GA and the resulting designs. The results show that the optimal designs have overall performance improvement of 18% relative to the baseline. Additionally, a fin constructed of a lower conductivity material (such as an Inconel super alloy that might be necessary for waste heat recovery applications)results in lower overall performance improvement (11%)and optimal designs with higher pressure drop relative to their baseline, and relative to optimal designs produced using higher conductivity materials.

3D Optimization↗
NASA NTRS1984

Models for the Effects of G-seat Cuing on Roll-axis Tracking Performance

Including whole-body motion in a flight simulator improves performance for a variety of tasks requiring a pilot to compensate for the effects of unexpected disturbances. A possible mechanism for this improvement is that whole-body motion provides high derivative vehicle state information whic allows the pilot to generate more lead in responding to the external disturbances. During development of motion simulating algorithms for an advanced g-cuing system it was discovered that an algorithm based on aircraft roll acceleration producted little or no performance improvement. On the other hand, algorithms based on roll position or roll velocity produced performance equivalent to whole-body motion. The analysis and modeling conducted at both the sensory system and manual control performance levels to explain the above results are described.

Levison, W. H.↗
NASA NTRS2003

Jell-Molds and Cookie-cutters: Shrinkwrap Isn't Just for Leftovers Anymore

So what is Shrinkwrap all about? For those of you who may not know about it, Shrinkwrap is a type of data structure that can manifest itself as a feature or model. It is cleverly covered up, almost hidden, and doesn't get the press or widespread use of a solid or surface. The shrinkwrap feature is located under the data sharing submenu of the feature menu. The shrinkwrap feature, as described by PTC, is a collection of surfaces and datum features of a model that represents the exterior of the model . The advantages and applications of the shrinkwrap feature are in the creation of minimal memory guzzling representations of assemblies. These can be used to represent subassemblies in parent assemblies, and can handle control of dependency issues, geometry represented, and additional references through the use of the shrinkwrap feature options. The shrinkwrap model is an option available under the save as umbrella. Its function, as described by PTC, is to share data with internal and external design groups and improve performance in large assembly design . Some of the benefits of the shrinkwrap model include being able to represent complex assemblies with a single, lightweight part that protects design intent and parametric data, and the ability to improve performance of large assembly modeling in the area of less load time. The proper-scale models can be saved as IGES, STEP, and VRML (for fly-throughs).

Randazzo, John↗
NASA NTRS2008

L1 Adaptive Control Law for Flexible Space Launch Vehicle and Proposed Plan for Flight Test Validation

This paper explores application of the L1 adaptive control architecture to a generic flexible Crew Launch Vehicle (CLV). Adaptive control has the potential to improve performance and enhance safety of space vehicles that often operate in very unforgiving and occasionally highly uncertain environments. NASA s development of the next generation space launch vehicles presents an opportunity for adaptive control to contribute to improved performance of this statically unstable vehicle with low damping and low bending frequency flexible dynamics. In this paper, we consider the L1 adaptive output feedback controller to control the low frequency structural modes and propose steps to validate the adaptive controller performance utilizing one of the experimental test flights for the CLV Ares-I Program.

Kharisov, Evgeny↗
NASA NTRS2017

Using Neural Networks to Improve the Performance of Radiative Transfer Modeling Used for Geometry Dependent Surface Lambertian-Equivalent Reflectivity Calculations

Surface Lambertian-equivalent reflectivity (LER) is important for trace gas retrievals in the direct calculation of cloud fractions and indirect calculation of the air mass factor. Current trace gas retrievals use climatological surface LER's. Surface properties that impact the bidirectional reflectance distribution function (BRDF) as well as varying satellite viewing geometry can be important for retrieval of trace gases. Geometry Dependent LER (GLER) captures these effects with its calculation of sun normalized radiances (I/F) and can be used in current LER algorithms (Vasilkov et al. 2016). Pixel by pixel radiative transfer calculations are computationally expensive for large datasets. Modern satellite missions such as the Tropospheric Monitoring Instrument (TROPOMI) produce very large datasets as they take measurements at much higher spatial and spectral resolutions. Look up table (LUT) interpolation improves the speed of radiative transfer calculations but complexity increases for non-linear functions. Neural networks perform fast calculations and can accurately predict both non-linear and linear functions with little effort.

Geometry Dependent LER (GLER) capture↗
NASA NTRS1978

NASA/General Electric Engine Component Improvement Program

The Engine Component Improvement (ECI) Program has been initiated in connection with projects designed to reduce the impact of the world-wide energy crisis in the area of aviation. The two parts of the ECI program have the overall objective to identify and quantify the sources and causes of CF6 engine performance deterioration, and to reduce the fuel consumption of CF6 engines through the development and the incorporation of various performance improvement concepts. The CF6 high-bypass turbofan engine was selected as a basis for this effort, since it is expected to be a significant fuel user in commercial revenue service for the next 15 to 20 years. The first part of the ECI program represents the initial step in an effort to achieve a goal of five percent reduction in fuel usage for CF6 engines in the 1979-82 time period. The first performance improvement concept selected is an improved efficiency fan blade. Other improvements are related to a short core exhaust system and an improved high pressure turbine.

Albright, A. J.↗