Search NASA⌕ Search

SEARCH · Search NASA

Results for “protection system”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Structural tests on a tile/strain isolation pad thermal protection system

The aluminum skin of the space shuttle is covered by a thermal protection system (TPS) consisting of a low density ceramic tile bonded to a matted-felt material called strain insulation pad (SIP). The structural characteristics of the TPS were studied experimentally under selected extreme load conditions. Three basic types of loads were imposed: tension, eccentrically applied tension, and combined in-plane force and transverse pressure. For some tests, transverse pressure was applied rapidly to simulate a transient shock wave passing over the tile. The failure mode for all specimens involved separation of the tile from the SIP at the silicone rubber bond interface. An eccentrically applied tension load caused the tile to separate from the SIP at loads lower than experienced at failure for pure tension loading. Moderate in-plane as well as shock loading did not cause a measurable reduction in the TPS ultimate failure strength. A strong coupling, however, was exhibited between in-plane and transverse loads and displacements.

Williams, J. G.↗
NASA NTRS1989

QM-8 field joint protection system, volume 7

The pre-launch functioning data of the Field Joint Protection System (JPS) used on QM-8 are presented. Also included is the post fire condition of the JPS components following the test firing of the motor. The JPS components are: field joint heaters; field joint sensors; field joint moisture seal; moisture seal kevlar retaining straps; field joint external extruded cork insulation; vent valve; power cables; and igniter heater.

Hale, Elgie↗
NASA NTRS2006

Lightweight Ablative and Ceramic Thermal Protection System Materials for NASA Exploration Systems Vehicles

As a collaborative effort among NASA Centers, the "Lightweight Nonmetallic Thermal Protection Materials Technology" Project was set up to assist mission/vehicle design trade studies, to support risk reduction in thermal protection system (TPS) material selections, to facilitate vehicle mass optimization, and to aid development of human-rated TPS qualification and certification plans. Missions performing aerocapture, aerobraking, or direct aeroentry rely on advanced heatshields that allow reductions in spacecraft mass by minimizing propellant requirements. Information will be presented on candidate materials for such reentry approaches and on screening tests conducted (material property and space environmental effects tests) to evaluate viable candidates. Seventeen materials, in three classes (ablatives, tiles, and ceramic matrix composites), were studied. In additional to physical, mechanical, and thermal property tests, high heat flux laser tests and simulated-reentry oxidation tests were performed. Space environmental effects testing, which included exposures to electrons, atomic oxygen, and hypervelocity impacts, was also conducted.

Valentine, Peter G.↗
NASA NTRS2006

In-Space Repair of Reinforced Carbon-Carbon Thermal Protection System Structures

Advanced repair and refurbishment technologies are critically needed for the thermal protection system of current space transportation system as well as for future Crew Exploration Vehicles (CEV). The damage to these components could be caused by impact during ground handling or due to falling of ice or other objects during launch. In addition, in-orbit damage includes micrometeoroid and orbital debris impact as well as different factors (weather, launch acoustics, shearing, etc.) during launch and re-entry. The GRC developed GRABER (Glenn Refractory Adhesive for Bonding and Exterior Repair) material has shown multiuse capability for repair of small cracks and damage in reinforced carbon-carbon (RCC) material. The concept consists of preparing an adhesive paste of desired ceramic with appropriate additives and then applying the paste to the damaged/cracked area of the RCC composites with adhesive delivery system. The adhesive paste cures at 100-120 C and transforms into a high temperature ceramic during simulated entry conditions. A number of plasma torch and ArcJet tests were carried out to evaluate the crack repair capability of GRABER materials for Reinforced Carbon-Carbon (RCC) composites. For the large area repair applications, integrated system for tile and leading edge repair (InSTALER) have been developed. In this presentation, critical in-space repair needs and technical challenges as well as various issues and complexities will be discussed along with the plasma performance and post test characterization of repaired RCC materials.

Singh, Mrityunjay↗
NASA NTRS2011

Thermal protection system ablation sensor

An isotherm sensor tracks space vehicle temperatures by a thermal protection system (TPS) material during vehicle re-entry as a function of time, and surface recession through calibration, calculation, analysis and exposed surface modeling. Sensor design includes: two resistive conductors, wound around a tube, with a first end of each conductor connected to a constant current source, and second ends electrically insulated from each other by a selected material that becomes an electrically conductive char at higher temperatures to thereby complete an electrical circuit. The sensor conductors become shorter as ablation proceeds and reduced resistance in the completed electrical circuit (proportional to conductor length) is continually monitored, using measured end-to-end voltage change or current in the circuit. Thermocouple and/or piezoelectric measurements provide consistency checks on local temperatures.

Gorbunov, Sergey↗
NASA NTRSDate not supplied

Boundary-Layer Flow Simulations Over Ablating Woven Thermal Protection System Material

Spallation is the mechanical removal of small chunks of material gets removed typically due to high shear conditions of the flow field. This reduces the ability of the thermal protection system (TPS) material to protect the spacecraft as well as cause turbulence in the flow causing higher heating rates. In this work, we focus on the material removal through ablation and high shear flow within the boundary layer region of woven TPS material. Woven TPS (WTPS) material is the latest class of material developed by NASA, to be used within the next generation of space flights. They are complex interlocked weaves designed to create a rigid structure that is highly resistant to heat and can be easily designed and tailored for a wide variety of entry environments. Due to material removal resulting from chemical degradation, the structural integrity of TPS material is affected. Spallation occurs when this structurally compromised material is exposed to the high shear flow conditions within the boundary layer. In order to understand the spallation mechanism within WTPS material, we first perform the material removal simulations which occur primarily through oxidation to obtain the microstructure at various stages of degradation. These simulations are performed using the Porous Microstructure Analysis (PuMA) software developed at NASA Ames. The micro-structure geometry used within these simulations were generated artificially to be similar to the 3D weave architecture of MSR-EEV (Mars Sample Return - Earth Entry Vehicle). The various eroded TPS micro-structures are then subjected to the boundary layer flow conditions to obtain critical surface quantities which contribute to the structural failure mechanism such as heat flux, pressure, and shear stress. The direct simulation Monte Carlo (DSMC) methodology is used to perform these simulations in order to accurately capture the strong gradients within the high-temperature boundary layer flow over the intricate geometry of WTPS material. The boundary layer profile is directly taken from the Computational Fluid Dynamics (CFD) simulation and provided as boundary conditions to the DSMC inlet and outlet. Further, the variation of these properties as the microstructure undergoes changes due to oxidation is also investigated. Finally, these quantities are used as input in PuMA to understand the material expansion/compression and strain within the woven TPS geometry and help in developing a comprehensive spallation and structure failure model.

microstructure↗
NASA NTRSDate not supplied

Boundary-Layer Flow Simulations Over Ablating Woven Thermal Protection System Material

Spallation is the mechanical removal of small chunks of material gets removed typically due to high shear conditions of the flow field. This reduces the ability of the thermal protection system (TPS) material to protect the spacecraft as well as cause turbulence in the flow causing higher heating rates. In this work, we focus on the material removal through ablation and high shear flow within the boundary layer region of woven TPS material. Woven TPS (WTPS) material is the latest class of material developed by NASA, to be used within the next generation of space flights. They are complex interlocked weaves designed to create a rigid structure that is highly resistant to heat and can be easily designed and tailored for a wide variety of entry environments. Due to material removal resulting from chemical degradation, the structural integrity of TPS material is affected. Spallation occurs when this structurally compromised material is exposed to the high shear flow conditions within the boundary layer. In order to understand the spallation mechanism within WTPS material, we first perform the material removal simulations which occur primarily through oxidation to obtain the microstructure at various stages of degradation. These simulations are performed using the Porous Microstructure Analysis (PuMA) software developed at NASA Ames. The micro-structure geometry used within these simulations were generated artificially to be similar to the 3D weave architecture of MSR-EEV (Mars Sample Return - Earth Entry Vehicle). The various eroded TPS micro-structures are then subjected to the boundary layer flow conditions to obtain critical surface quantities which contribute to the structural failure mechanism such as heat flux, pressure, and shear stress. The direct simulation Monte Carlo (DSMC) methodology is used to perform these simulations in order to accurately capture the strong gradients within the high-temperature boundary layer flow over the intricate geometry of WTPS material. The boundary layer profile is directly taken from the Computational Fluid Dynamics (CFD) simulation and provided as boundary conditions to the DSMC inlet and outlet. Further, the variation of these properties as the microstructure undergoes changes due to oxidation is also investigated. Finally, these quantities are used as input in PuMA to understand the material expansion/compression and strain within the woven TPS geometry and help in developing a comprehensive spallation and structure failure model.

microstructure↗
NASA NTRSDate not supplied

Thermal Conductivity of 3D Woven Composite Thermal Protection System Materials via Multiscale Recursive Micromechanics

Multiscale micromechanics predictions have been made for the effective thermal conductivities and local thermal fields for a novel 3D woven composite thermal protection system material. The Multiscale Recursive Micromechanics approach, which enables micromechanics models to call other micromechanics models (or themselves recursively) to consider finer and finer length scales, has been employed. The multiscale model uses a recently developed version of the High-Fidelity Generalized Method of Cells micromechanics theory at each of three length scales. Results focus on the impact of the microstructural geometry representation at each length scale on the material’s effective thermal conductivity, along with the local thermal flux and temperature fields induced in the microstructures.

Composites↗
NASA NTRS2019

Heatshield for Extreme Entry Environment Technology (HEEET) Thermal Protection System (TPS)

Starting in 2013 and completing in 2019, the Heatshield for Extreme Entry Environment Technology (HEEET) project has been working to mature a 3-D Woven Thermal Protection System (TPS) to Technical Readiness Level (TRL) 6 to support future NASA missions to destinations with extreme entry environments such as Venus, Saturn, Uranus, Neptune and high-speed sample return missions to Earth. A key aspect of the project has been the building and testing of a 1-meter base diameter Engineering Test Unit (ETU) representative of what could be used for a Saturn probe. This paper provides a high-level overview of the HEEET project including manufacturing and testing of the ETU for structural model verification, establish system capability and verify manufacturing workmanship.

Extreme Entry Environment↗
NASA NTRS2021

Thermal Conductivity of 3D Woven Composite Thermal Protection System Materials via Multiscale Recursive Micromechanics

Multiscale micromechanics predictions have been made for the effective thermal conductivities and local thermal fields for a novel 3D woven composite thermal protection system material. The Multiscale Recursive Micromechanics approach, which enables micromechanics models to call other micromechanics models (or themselves recursively) to consider finer and finer length scales, has been employed. The multiscale model uses a recently developed version of the High-Fidelity Generalized Method of Cells micromechanics theory at each of three length scales. Results focus on the impact of the microstructural geometry representation at each length scale on the material’s effective thermal conductivity, along with the local thermal flux and temperature fields induced in the microstructures.

composite↗
NASA NTRS1979

Overview of helicopter ice protection system developments

Helicopter ice protection design criteria was developed and technological shortcoming in meeting helicopter mission requirements is that of helicopter rotor blade ice protection. Airframe components are protected using existing technology while the rotor blade protected using the cyclic electrothermal deicing concept.

Richard I Adams↗
NASA NTRS1994

Analysis of the Shuttle Orbiter reinforced carbon-carbon oxidation protection system

Reusable, oxidation-protected reinforced carbon-carbon (RCC) has been successfully flown on all Shuttle Orbiter flights. Thermal testing of the silicon carbide-coated RCC to determine its oxidation characteristics has been performed in convective (plasma Arc-Jet) heating facilities. Surface sealant mass loss was characterized as a function of temperature and pressure. High-temperature testing was performed to develop coating recession correlations for predicting performance at the over-temperature flight conditions associated with abort trajectories. Methods for using these test data to establish multi-mission re-use (i.e., mission life) and single mission limits are presented.

Williams, S. D.↗
NASA NTRSDate not supplied

Advanced TUFROC Thermal Protection System Evolution Under Re-entry like Conditions

Toughened Unipiece Fibrous Reinforced Oxidation-resistant Composite (TUFROC) and its successor, Advanced TUFROC, are state-of-the-art thermal protection systems (TPS) for high temperature reusable applications. Originally designed for use on the wing-leading edge of X-37B, TUFROC is an insulative tiled system consisting of a low-conductivity ceramic base, a carbonaceous cap, and multiple coatings for thermal performance. The improved Advanced TUFROC has demonstrated reusability up to 2900 °F and single use capabilities exceeding 3200 °F. This effort explores the evolution of Advanced TUFROC when exposed to re-entry like conditions via arc jet testing. Chemical reactions and constituent migration resulting from the aerothermal heating are known to occur and are studied in detail. Further, the interaction between the multiple constituents and layers will be discussed as this is believed to have a significant impact on the overall performance. Characterization includes structural analysis via optical microscopy, scanning electron microscopy and energy-dispersive x-ray spectroscopy.

Thermal protection system↗
NASA NTRS2016

Earth Entry Requirements for Mars, Europa and Enceladus Sample Return Missions: A Thermal Protection System Perspective

This oral presentation will be given at the 13th International Planetary Probe Workshop on June 14th, 2016 and will cover the drivers for reliability and the challenges faced in selecting and designing the thermal protection system (TPS). In addition, an assessment is made on new emerging TPS related technologies that could help with designs to meet the planetary protection requirements to prevent backward (Earth) contamination by biohazardous samples.

Earth Entry↗
NASA NTRS2024

Advanced Lightweight TUFROC Thermal Protection System for Space Plane Applications

Toughened Uni-piece Fibrous Reinforced Oxidation-resistant Composite (TUFROC) represents the state of the art in low-cost, reusable spacecraft Thermal Protection Systems (TPS) with high temperature capability and is flight proven on the USAF X-37B. The two-piece design takes advantage of a low-conductivity porous silica substrate combined with high-temperature-capable carbon cap and surface treatments. NASA has updated the chemical composition of the surface treatments resulting in improved high-heating capability and reusability. The new system, called Advanced TUFROC, experiences a lower surface temperature (by ~80 K) at identical aerothermal heating conditions compared to the original formulation, now called Standard TUFROC. The reduced heating is attributed to the lower catalytic efficiency of the new formulation, which results in reduced exothermic atom recombination rates at the surface. Multiple arc-jet test campaigns demonstrate that Advanced TUFROC has the ability to withstand long and repeated exposures at 1866 K or a shorter duration exposure at 1980 K without recession or damage to TPS. Furthermore, an improved arc-jet article design for assessing 3-dimensional flow over a wing leading edge has been developed and tested. This article allows for assessment of heating at a tile gap under flight-relevant conditions at significantly reduced article fabrication and arc-jet facility configuration costs compared to prior work.

TUFROC↗
NASA NTRSDate not supplied

Development and Sizing of the Mars 2020 Thermal Protection System

The Mars 2020 entry vehicle successfully delivered the Perseverance rover to the Martian surface on 18 February 2021. The entry vehicle aeroshell was shielded from aerodynamic heating with a thermal protection system (TPS) made of three different ablative materials. This paper provides an overview of the methodology and assumptions employed for the thermal sizing and design of the Mars 2020 aeroshell TPS. The sizing results demonstrate that the as-built thicknesses of the TPS materials were sufficient to withstand the predicted aerothermal environments without exceeding temperature limits of the underlying aeroshell structure. This paper also provides an overview of the ground testing performed in NASA arc jet facilities to verify the performance of flight lot TPS materials. Finally, temperature data returned by thermocouples embedded in the flight vehicle TPS are compared with predictions by the thermal response models used in pre-flight TPS sizing.

Mars2020↗
NASA NTRSDate not supplied

Development and Sizing of the Mars 2020 Thermal Protection System

The Mars 2020 entry vehicle successfully delivered the Perseverance rover to the Martian surface on 18 February 2021. The entry vehicle aeroshell was shielded from aerodynamic heating with a thermal protection system (TPS) made of three different ablative materials. This paper provides an overview of the methodology and assumptions employed for the thermal sizing and design of the Mars 2020 aeroshell TPS. The sizing results demonstrate that the as-built thicknesses of the TPS materials were sufficient to withstand the predicted aerothermal environments without exceeding temperature limits of the underlying aeroshell structure. This paper also provides an overview of the ground testing performed in NASA arc jet facilities to verify the performance of flight lot TPS materials. Finally, temperature data returned by thermocouples embedded in the flight vehicle TPS are compared with predictions by the thermal response models used in pre-flight TPS sizing.

Mars2020↗