SEARCH · Search NASA

Results for “qualification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS2015

James Webb Space Telescope (JWST) Integrated Science Instruments Module (ISIM) Electronics Compartment (IEC) Conformal Shields Composite Bond Structure Qualification Test Method

The JWST IEC conformal shields are mounted onto a composite frame structure that must undergo qualification testing to satisfy mission assurance requirements. The composite frame segments are bonded together at the joints using epoxy, EA 9394. The development of a test method to verify the integrity of the bonded structure at its operating environment introduces challenges in terms of requirements definition and the attainment of success criteria. Even though protoflight thermal requirements were not achieved, the first attempt in exposing the structure to cryogenic operating conditions in a thermal vacuum environment resulted in approximately 1 bonded joints failure during mechanical pull tests performed at 1.25 times the flight loads. Failure analysis concluded that the failure mode was due to adhesive cracks that formed and propagated along stress concentrated fillets as a result of poor bond squeeze-out control during fabrication. Bond repairs were made and the structures successfully re-tested with an improved LN2 immersion test method to achieve protoflight thermal requirements.

Thermal Vacuum Testing Chamber↗

NASA NTRS2015

Design, Qualification and Integration Testing of the High-Temperature Resistance Temperature Device for Stirling Power System

The Advanced Stirling Radioisotope Generator (ASRG), developed from 2006 to 2013 under the joint sponsorship of the United States Department of Energy (DOE) and National Aeronautics and Space Administration (NASA) to provide a high-efficiency power system for future deep space missions, employed Sunpower Incorporated's Advanced Stirling Convertors (ASCs) with operating temperature up to 840 C. High-temperature operation was made possible by advanced heater head materials developed to increase reliability and thermal-to-mechanical conversion efficiency. During a mission, it is desirable to monitor the Stirling hot-end temperature as a measure of convertor health status and assist in making appropriate operating parameter adjustments to maintain the desired hot-end temperature as the radioisotope fuel decays. To facilitate these operations, a Resistance Temperature Device (RTD) that is capable of high-temperature, continuous long-life service was designed, developed and qualified for use in the ASRG. A thermal bridge was also implemented to reduce the RTD temperature exposure while still allowing an accurate projection of the ASC hot-end temperature. NASA integrated two flight-design RTDs on the ASCs and assembled into the high-fidelity Engineering Unit, the ASRG EU2, at Glenn Research Center (GRC) for extended operation and system characterization. This paper presents the design implementation and qualification of the RTD, and its performance characteristics and calibration in the ASRG EU2 testing.

Deep Space↗

NASA NTRS2016

APM for a Constellation Intersatellite Link - EM Qualification and Lessons Learned

For an Intersatellite Link (ISL) of a future constellation program, a study phase was initiated by ESA to design a mechanism for Radio Frequency communication. Airbus DS Friedrichshafen (ADSF) proposed a design based on the Antenna Pointing Mechanism (APM) family with modifications that met the stated needs of the constellation. A qualification program was started beginning in September 2015 to verify the launch and thermal loads and the equipment performance (Radio Frequency, Pointing, Microvibration and Magnetic Moment). Technical challenges identified with the Engineering Model will be discussed within this paper.

Hartel, Frank↗

NASA NTRS2017

Space Technology: Game Changing Development Deep Space Engine (DSE) 100 lbf and 5 lbf Thruster Development and Qualification

Science mission studies require spacecraft propulsion systems that are high-performance, lightweight, and compact. Highly matured technology and low-cost, short development time of the propulsion system are also very desirable. The Deep Space Engine (DSE) 100-lbf thruster is being developed to meet these needs. The overall goal of this game changing technology project is to qualify the DSE thrusters along with 5-lbf attitude control thrusters for space flight and for inclusion in science and exploration missions. The aim is to perform qualification tests representative of mission duty cycles. Most exploration missions are constrained by mass, power and cost. As major propulsion components, thrusters are identified as high-risk, long-lead development items. NASA spacecraft primarily rely on 1960s' heritage in-space thruster designs and opportunities exist for reducing size, weight, power, and cost through the utilization of modern materials and advanced manufacturing techniques. Advancements in MON-25/MMH hypergolic bipropellant thrusters represent a promising avenue for addressing these deficiencies with tremendous mission enhancing benefits. DSE is much lighter and costs less than currently available thrusters in comparable thrust classes. Because MON-25 propellants operate at lower temperatures, less power is needed for propellant conditioning for in-space propulsion applications, especially long duration and/or deep-space missions. Reduced power results in reduced mass for batteries and solar panels. DSE is capable of operating at a wide propellant temperature range (between -22 F and 122 F) while a similar existing thruster operates between 45 F and 70 F. Such a capability offers robust propulsion operation as well as flexibility in design. NASA's Marshall Space Flight Center evaluated available operational Missile Defense Agency heritage thrusters suitable for the science and lunar lander propulsion systems.

Barnett, Gregory↗

NASA NTRS2017

9- by 15-Foot Low-Speed Wind Tunnel Acoustic Free Field Evaluation; Part 1: Qualification Report Summary and Part 2: Anechoic Environment Characterization Field Test Report

This report describes test results from an assessment of the acoustically treated 9x15 Foot Low Speed Wind Tunnel at the NASA Glenn Research Center in Cleveland, Ohio in July of 2016. The tests were conducted in accordance with the recently adopted international standard ISO 26101-2012 on Qualification of Free Field Test Environments. This method involves moving a microphone relative to a source and comparing the sound pressure level versus distance measurements with theoretical inverse square law spreading.

propulsion↗

NASA NTRS2018

Lessons Learned in the Flight Qualification of the S-NPP and NOAA-20 Solar Array Mechanisms

Deployable solar arrays are the energy source used on almost all Earth orbiting spacecraft and their release and deployment are mission-critical; fully testing them on the ground is a challenging endeavor. The 8 meter long deployable arrays flown on two sequential NASA weather satellites were each comprised of three rigid panels almost 2 meters wide. These large panels were deployed by hinges comprised of stacked constant force springs, eddy current dampers, and were restrained through launch by a set of four releasable hold-downs using shape memory alloy release devices. The ground qualification testing of such unwieldy deployable solar arrays, whose design was optimized for orbital operations, proved to be quite challenging and provides numerous lessons learned. A paperwork review and follow-up inspection after hardware storage determined that there were negative torque margins and missing lubricant, this paper will explain how these unexpected issues were overcome. The paper will also provide details on how the hinge subassemblies, the fully-assembled array, and mechanical ground support equipment were subsequently improved and qualified for a follow-on flight with considerably less difficulty. The solar arrays built by Ball Aerospace Corp. for the Suomi National Polar Partnership (S-NPP) satellite and the Joint Polar Satellite System (JPSS-1) satellite (now NOAA-20) were both successfully deployed on-obit and are performing well.

Helfrich, Daniel↗

NASA NTRS2018

Lessons Learned in the Flight Qualification of the S-NPP and NOAA-20 Solar Array Mechanisms

Deployable solar arrays are the energy source used on almost all Earth orbiting spacecraft and their release and deployment are mission-critical; fully testing them on the ground is a challenging endeavor. The 8 meter long deployable arrays flown on two sequential NASA weather satellites were each comprised of three rigid panels almost 2 meters wide. These large panels were deployed by hinges comprised of stacked constant force springs, eddy current dampers, and were restrained through launch by a set of four releasable hold-downs using shape memory alloy release devices. The ground qualification testing of such unwieldy deployable solar arrays, whose design was optimized for orbital operations, proved to be quite challenging and provides numerous lessons learned. A paperwork review and follow-up inspection after hardware storage determined that there were negative torque margins and missing lubricant, this paper will explain how these unexpected issues were overcome. The paper will also provide details on how the hinge subassemblies, the fully-assembled array, and mechanical ground support equipment were subsequently improved and qualified for a follow-on flight with considerably less difficulty. The solar arrays built by Ball Aerospace Corp. for the Suomi National Polar Partnership (SNPP) satellite and the Joint Polar Satellite System (JPSS-1) satellite (now NOAA-20) were both successfully deployed on-obit and are performing well.

Sexton, Adam↗

NASA NTRS2019

Textile Material Lessons Learned During the Design and Qualification of the NASA Orion Capsule Parachute Assembly System

The NASA Orion Capsule Parachute Assembly System (CPAS) development and qualification testing was completed in September 2018. Over the course of the airdrop and ground testing campaign, the team benefited from the ability to design, test, and adjust the design based on observations and inspection results. While the design team used the best knowledge available and attempted to utilize best practices, a number of lessons were learned that should be documented for consideration by future designers. This paper describes these lessons learned including the use of textile reefing loops, the importance of performing joint tests, the impact of using bight sleeves on parachute deployment, and a surprising number of design changes required in the CPAS system after the decision was made to change the suspension line braid to save system mass.

Anderson, Brian P.↗

NASA NTRS2019

Space Flight Optoelectronics and Photonics Qualification

The Photonics group top level processes regarding development and qualification of space flight hardware for optoelectronic components along with our contributions and successes with LIDAR systems, space flight reliability heritage, and our testing capabilities are conveyed with this power point presentation.

Optical Systems↗

NASA NTRSDate not supplied

Flexible Solar Array Qualification Protocols (FSAP-ACO)

This poster highlights the Game Changing Development Program task, Space Act Agreement between Maxar Technologies and NASA to test 5-junction solar cells on roll out compatible blankets through qualification protocols similar to AIAA Standards S-111/112. A description of the planned work and current status is included.

Jeremiah Mcnatt↗

NASA NTRS2004

A chip and pixel qualification methodology on imaging sensors

This paper presents a qualification methodology on imaging sensors. In addition to overall chip reliability characterization based on sensor's overall figure of merit, such as Dark Rate, Linearity, Dark Current Non-Uniformity.

Novak, Frank↗

NASA NTRS2009

Mitigation selection and qualification recommendations for Xilinx Virtex, Virtex-II, and Virtex-4 field programmable gate arrays

This work discusses mitigation selection and qualification techniques for Xilinx reconfigurable field programmable gate arrays (FPGAs). The aim of the paper is to provide readers with a better understanding of the engineering/reliability/project cost relationship that occurs when developing a mitigation strategy for static random access memory (SRAM)-based FPGAs.

Allen, Gregory↗

NASA NTRS2021

Lessons Learned from Screening and Qualification of COTS Capacitors

A traditional approach to screening and qualification of hi-rel COTS capacitors and its limitations are analyzed. Results of testing of four types of COTS capacitors for L2 projects are summarized. The types include DLA drawing tantalum MnO2 capacitors, high-voltage hermetically sealed polymer tantalum capacitors, multianode COTS+ capacitors, and feedthrough BME ceramic capacitors. Lessons learned from this experience might accelerate processes and reduce risks of inclusion of COTS components in space projects.

reliability↗

NASA NTRS2021

Screening and Qualification of BME Feedthrough Capacitors for a Space Project

Surface mount technology feedthrough ceramic capacitors are gaining popularity in Hi-Rel systems due to small size and great filtering characteristics. In this work, BME feedthrough capacitors compliant with AEC-Q200 requirements have been evaluated, screened and qualified for a space project. Evaluation included analysis of the effect of post-soldering thermal shocks, temperature dependencies of leakage currents, distribution of breakdown voltages, assessments of high-current capability, and thermal resistance of the parts. The parts have been screened and qualified at conditions close to the military requirements for ceramic capacitors. No failures were detected during screening including burning-in, but two samples failed during monitored 2000 hour life testing at 125C and two times rated voltage. Failure analysis revealed manufacturing defects that required additional analysis of screening and qualification test conditions. Highly accelerated life testing (HALT) has been carried out to assess reliability acceleration factors and the probability of failure at the use conditions. An approach to selection of adequate burning-in and life test conditions is discussed.

Alexander Teverovsky↗

NASA NTRS2021

Screening and Qualification of BME Feedthrough Capacitors for a Space Project

Alexander Teverovsky↗

NASA NTRSDate not supplied

Process Qualification Concepts in NASA-STD-6030

- Terminology - Definition and role of QMP in the NASA-STD-6030 framework - Qualification checklist for evaluating a candidate AM material process - Types of data needed to evaluate the metrics for a QMP - Advocacy for a singular, contained data entity that enables QMP evaluation and other aspects of the AM ecosystem - Material Engineering Equivalence Baseline - Discussion of Material Engineering Equivalence concepts - Summary

Doug Wells↗

NASA NTRSDate not supplied

NASA's Certification and Qualification Challenges for Additively Manufactured Hardware: What Is Next?

In 2021, NASA released NASA-STD-6030 “Additive Manufacturing Requirements for Spaceflight Systems” to create qualification and certification strategies for mature metallic and non-metallic AM materials and technologies. While these standards have had an immediate impact on the additive manufacturing (AM) industry, there remain many challenges that have yet to be overcome. NASA and its partners in academia and industry are working together to proactively address these issues. One of the most critical needs is a Probabilistic Damage Tolerance Assessment (PDTA) approach, which includes the development of computational modeling, understanding the “effect of defects”, and the implementation of in-situ process monitoring and inspection techniques.

Will Tilson↗

NASA NTRSDate not supplied

Powder Bed Fusion Laser Beam Metals Additive Manufacturing: Process Monitoring Approaches for Qualification and Certification

The use of in-situ process monitoring is of interest to lower the cost of inspection for the qualification of powder bed fusion laser beam metal (PBF-LB/M) additively manufactured (AM) parts. Precise monitoring of the PBF-LB/M AM build process constitutes a multi-scale and multi-discipline task. There are several significant challenges to the in-situ approach: the synchronization of sensor signals to process steps; the physical interpretation and classification of sensor signals; managing very large datasets; and comparing the inputs with the observed monitoring signals. At NASA Langley Research Center, a configurable architecture additive testbed has been developed to monitor the build process with synchronized sensors. The philosophy and method adopted for the synchronization of the cameras with laser power and position throughout a complex PBF-LB/M AM build will be described. The synchronized in-situ monitoring signals are compared with ex-situ nondestructive inspection, x-ray computed tomography (XCT). Such comparisons permit a better understanding of how the sequential process actions of LPBF-AM can affect build quality. The multi-scale and complex process of printing additively manufactured (AM) parts can have unexpected, but predictable, build conditions that result in material microstructure variability. This presentation will describe an additive manufacturing model-based process metric (AM-PM) computational method that is a fully parallel reduced order modeling approach developed to evaluate the evolution of AM processes. This method couples the known sequence of the AM process with a physically informed nearest neighbors’ calculation to map the conditions of a part-scale build. The result is a map of the build that is derived directly from build files or in-situ process monitoring sensors. The methodology of the approach will be described and mapped to the porosity observed from XCT for a complex PBF-LB/M build. Such comparative results develop understanding of how the sequential process actions can affect the PBF-LB/M AM build quality and microstructure variability.

Laser Powder Bed Fusion↗