Search NASA⌕ Search

SEARCH · Search NASA

Results for “shuttle effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Hypervelocity supersonic nozzle beam source of atomic oxygen

A hypervelocity source of atomic oxygen was developed. Dissociation of molecular oxygen is accomplished by injection into a flow of helium and/or argon which has been heated in a commercial plasma torch. Atomic velocities of up to 4 kms(-1) were produced; recent improvements offer the possibility of even higher velocities. This source was utilized in studies of translational-to-vibrational energy transfer in carbon dioxide and in an investigation of the shuttle glow effect.

Freedman, A.↗

A cost-effective component modes analysis for Shuttle payloads using a combination of frequency domain and time domain approaches

A combination of the time and frequency domains which employs the latter only where the former is inefficient or uncertain is used in Space Shuttle payloads' component mode analyses. Attention is given to the time histories at the launch vehicle/spacecraft interface. The frequency domain allows interface acceleration to be determined without recourse to a new, merged system eigenvalue solution and subsequent 'system modal' responses. The approach has been employed in Galileo spacecraft loads analyses.

Trubert, M.↗

A mechanism for the local concentration enhancement of the shuttle atmosphere

Preliminary calculations suggest that collisions between instreaming atmospheric constituents and secondary backscattered molecules can generate unexpectedly large enhancements in neutral gas concentrations in the vicinity of the shuttle. This effect is a result of a rapid decrease in the mean free path length of the scattered components following the initial expected concentration enhancement. A study will be outlined for the theoretical investigation of this mechanism. The shape dependence of associated glow halos on vehicle configuration will be discussed.

Rantanen, R.↗

Lightning current rate of rise in the new lightning flash model for the space shuttle program

The recently baselined Space Shuttle lightning effects flash model is discussed. The discussion is limited to the current rate(s) of rise. A review of some of the recent data is presented, as well as a discussion of how interaction processes affect the induced voltages and currents which arise from a lightning strike. It is concluded that the multiple pulse components of the new flash model present a more severe threat to complex avionic systems, than is presented by a single pulse having an extremely fast rate of rise.

Bankston, Nathaniel G.↗

Critical fluid thermal equilibration experiment (19-IML-1)

Gravity sometimes blocks all experimental techniques of making a desired measurement. Any pure fluid possesses a liquid-vapor critical point. It is defined by a temperature, pressure, and density state in thermodynamics. The critical issue that this experiment attempts to understand is the time it takes for a sample to reach temperature and density equilibrium as the critical point is approached; is it infinity due to mass and thermal diffusion, or do pressure waves speed up energy transport while mass is still under diffusion control. The objectives are to observe: (1) large phase domain homogenization without and with stirring; (2) time evolution of heat and mass after temperature step is applied to a one phase equilibrium sample; (3) phase evolution and configuration upon going two phase from a one phase equilibrium state; (4) effects of stirring on a low g two phase configuration; (5) two phase to one phase healing dynamics starting from a two phase low g configuration; and (6) effects of shuttle acceleration events on spatially and temporally varying compressible critical fluid dynamics.

Wilkinson, R. Allen↗

In-flight simulation studies at the NASA Dryden Flight Research Facility

Since the late 1950's, the National Aeronautics and Space Administration's Dryden Flight Research Facility has found in-flight simulation to be an invaluable tool. In-flight simulation has been used to address a wide variety of flying qualities questions, including low-lift-to-drag ratio approach characteristics for vehicles like the X-15, the lifting bodies, and the Space Shuttle; the effects of time delays on controllability of aircraft with digital flight-control systems, the causes and cures of pilot-induced oscillation in a variety of aircraft, and flight-control systems for such diverse aircraft as the X-15 and the X-29. In-flight simulation has also been used to anticipate problems and to avoid them and to solve problems once they appear. Presented here is an account of the in-flight simulation at the Dryden Flight Research Facility and some discussion. An extensive bibliography is included.

Shafer, Mary F.↗

In-flight simulation studies at the NASA Dryden Flight Research Facility

Since the late 1950's the National Aeronautics and Space Administration's Dryden Flight Research Facility has found in-flight simulation to be an invaluable tool. In-flight simulation has been used to address a wide variety of flying qualities questions, including low lift-to-drag ratio approach characteristics for vehicles like the X-15, the lifting bodies, and the space shuttle; the effects of time delays on controllability of aircraft with digital flight control systems; the causes and cures of pilot-induced oscillation in a variety of aircraft; and flight control systems for such diverse aircraft as the X-15 and the X-29. In-flight simulation has also been used to anticipate problems, avoid them, and solve problems once they appear. This paper presents an account of the in-flight simulation at the Dryden Flight Research Facility and some discussion. An extensive bibliography is included.

Shafer, Mary F.↗

Neuroscience Investigations: An Overview of Studies Conducted

The neural processes that mediate human spatial orientation and adaptive changes occurring in response to the sensory rearrangement encountered during orbital flight are primarily studied through second and third order responses. In the Extended Duration Orbiter Medical Project (EDOMP) neuroscience investigations, the following were measured: (1) eye movements during acquisition of either static or moving visual targets, (2) postural and locomotor responses provoked by unexpected movement of the support surface, changes in the interaction of visual, proprioceptive, and vestibular information, changes in the major postural muscles via descending pathways, or changes in locomotor pathways, and (3) verbal reports of perceived self-orientation and self-motion which enhance and complement conclusions drawn from the analysis of oculomotor, postural, and locomotor responses. In spaceflight operations, spatial orientation can be defined as situational awareness, where crew member perception of attitude, position, or motion of the spacecraft or other objects in three-dimensional space, including orientation of one's own body, is congruent with actual physical events. Perception of spatial orientation is determined by integrating information from several sensory modalities. This involves higher levels of processing within the central nervous system that control eye movements, locomotion, and stable posture. Spaceflight operational problems occur when responses to the incorrectly perceived spatial orientation are compensatory in nature. Neuroscience investigations were conducted in conjunction with U. S. Space Shuttle flights to evaluate possible changes in the ability of an astronaut to land the Shuttle or effectively perform an emergency post-landing egress following microgravity adaptation during space flights of variable length. While the results of various sensory motor and spatial orientation tests could have an impact on future space flights, our knowledge of sensorimotor adaptation to spaceflight is limited, and the future application of effective countermeasures depends, in large part, on the results from appropriate neuroscience investigations. Therefore, the objective of the neuroscience investigations could have a negative effect on mission success. The Neuroscience Laboratory, Johnson Space Center (JSC), implemented three integrated Detailed Supplementary Objectives (DSO) designed to investigate spatial orientation and the associated compensatory responses as a part of the EDOMP. The four primary goals were (1) to establish a normative database of vestibular and associated sensory changes in response to spaceflight, (2) to determine the underlying etiology of neurovestibular and sensory motor changes associated with exposure to microgravity and the subsequent return to Earth, (3) to provide immediate feedback to spaceflight crews regarding potential countermeasures that could improve performance and safety during and after flight, and (4) to take under consideration appropriate designs for preflight, in-flight, and postflight countermeasures that could be implemented for future flights.

Reschke, Millard F.↗

Shuttle Centaur engine cooldown evaluation and effects of expanded inlets on start transient

As part of the integration of the RL10 engine into the Shuttle Centaur vehicle, a satisfactory method of conditioning the engine to operating temperatures had to be established. This procedure, known as cooldown, is different from the existing Atlas Centaur due to vehicle configuration and mission profile differenced. The program is described, and the results of a Shuttle Centaur cooldown program are reported. Mission peculiarities cause substantial variation in propellant inlet conditions between the substantiated Atlas Centaur and Shuttle Centaur with the Shuttle Centaur having much larger variation in conditions. A test program was conducted to demonstrate operation of the RL10 engine over the expanded inlet conditions. As a result of this program, the Shuttle Centaur requirements were proven satisfactory. Minor configuration changes incorporated as a result of this program provide substantial reduction in cooldown propellant consumption.

Source record↗

The effect of wind variability on Space Shuttle flight

A data base of paired detailed wind profiles is developed for use in evaluating the STS ascent capability. The flight of the Shuttle is simulated through a sequence of measured detailed wind profiles and the wind effects on load and performance are evaluated. Since the wind measurement and simulation time requirements dictate that the launch decision be based on wind measurements taken about 3.5 hr before launch, a data base of paired detailed profiles is obtained in order to account for possible load increases due to wind profile changes during the final 3.5 hr before launch. Results show that the largest wind changes occur in winter at about 12 km altitude. At that time and altitude, it is found that there is a 5 percent risk that the wind component speed change will approximate 10 m/s in 3.5 hr. It is determined that the wind can vary over a period of 3.5 hr by more than 20 percent from the transition season to the winter season while somewhat smaller changes occur between the transition season and the summer season. It is concluded that these results demonstrate the feasibility of the wind change model concept and that this model should be considered for future use in Shuttle prelaunch operations.

Hill, C. K.↗

Roughness induced transition criteria for space shuttle-type vehicles

Tripping effectiveness of surface roughness on a delta wing shuttle orbiter model at 20 deg angle of attack is compared to that on plane and axisymmetrical bodies with and without longitudinal pressure gradients. The experimental data presented are compared on the basis of effective roughness Reynolds number since this parameter is not sensitive to flow conditions downstream of the roughness. The discussion covers the effective roughness Reynolds number as a function of roughness position Reynolds number, effective size ratio as a function of pressure gradient and distance from vehicle nose, and effect of spanwise roughness position on roughness effectiveness. It is shown that conventional criteria for sizing roughness elements which promote transition in two-dimensional zero-pressure gradient flows are insufficient for high-pressure gradient flows and three-dimensional flows. Roughness much smaller than that given by conventional criteria can cause transition and significantly increase the heating load.

Morrisette, E. L.↗

Effects of rain and fog on the Shuttle Ku-band microwave scanning beam landing system range and accuracy performance

The microwave Scanning Beam Landing System's (MSBLS) performance in fog and rain was studied. The fog and rain effects on the Shuttle Ku-band system were determined. Specifically, microwave attenuation, beam distortion, and coordinate errors resulting from operation of the MSBLS in poor weather conditions were evaluated. The main physical processes giving rise to microwave attenuation were found to be absorption and scattering by water droplets. The general theory of scattering and absorption used is discussed and a listing of applicable computer programs is provided.

Butler, D.↗

Effects of radiation environment on reusable nuclear shuttle system

Parametric tradeoff analyses of a wide spectrum of alternate tank configurations to minimize both primary and secondary, direct and scattered radiation sources emanating from the NERVA are reported. The analytical approach utilizing point kernel techniques is described and detailed data are presented on the magnitude of neutron/gamma doses for different locations. Single-tank configurations utilizing smaller cone angles and end cap radii were found to minimize integral radiation levels, hence, stage shielding-weight penalties for shuttle missions. Hybrid configurations employing an upper tank with a reduced cone angle and end cap radius result in low integral payload doses primarily due to the increased separation distance caused by the elongation of the larger capacity upper tank. A preliminary radiation damage assessment is discussed of possible reusable nuclear shuttle materials, components, and subsystems, and the possible effects of the radiation environment on various phases of RNS mission operations.

Lane, A. G.↗

Effect of load eccentricity and substructure deformation on ultimate strength of shuttle orbiter thermal protection system

The effect of load eccentricity and substructure deformation on the ultimate strength and stress displacement properties of the shuttle orbiter thermal protection system (TPS) was determined. The LI-900 Reusable Surface Insulation (RSI) tiles mounted on the .41 cm thick Strain Isolator Pad (SIP) were investigated. Substructure deformations reduce the ultimate strength of the SIP/tile TPS and increase the scatter in the ultimate strength data. Substructure deformations that occur unsymmetric to the tile can cause the tile to rotate when subjected to a uniform applied load. Load eccentricity reduces SIP/tile TPS ultimate strength and causes tile rotation.

Sawyer, J. W.↗

Shuttle Global Positioning System (GPS) design study

The effects of oscillator noise on Shuttle Global Positioning System (GPS) receiver performance, GPS navigation system self-test, GPS ground transmitter design to augment shuttle navigation, the effect of ionospheric delay modelling on GPS receiver design, and GPS receiver tracking of Shuttle transient maneuvers were investigated.

Nilsen, P. W.↗

Shared visions: Partnership of Rockwell International and NASA Cost Effectiveness Enhancements (CEE) for the space shuttle system integration program

As a result of limited resources and tight fiscal constraints over the past several years, the defense and aerospace industries have experienced a downturn in business activity. The impact of fewer contracts being awarded has placed a greater emphasis for effectiveness and efficiency on industry contractors. It is clear that a reallocation of resources is required for America to continue to lead the world in space and technology. The key to technological and economic survival is the transforming of existing programs, such as the Space Shuttle Program, into more cost efficient programs so as to divert the savings to other NASA programs. The partnership between Rockwell International and NASA and their joint improvement efforts that resulted in significant streamlining and cost reduction measures to Rockwell International Space System Division's work on the Space Shuttle System Integration Contract is described. This work was a result of an established Cost Effectiveness Enhancement (CEE) Team formed initially in Fiscal Year 1991, and more recently expanded to a larger scale CEE Initiative in 1992. By working closely with the customer in agreeing to contract content, obtaining management endorsement and commitment, and involving the employees in total quality management (TQM) and continuous improvement 'teams,' the initial annual cost reduction target was exceeded significantly. The CEE Initiative helped reduce the cost of the Shuttle Systems Integration contract while establishing a stronger program based upon customer needs, teamwork, quality enhancements, and cost effectiveness. This was accomplished by systematically analyzing, challenging, and changing the established processes, practices, and systems. This examination, in nature, was work intensive due to the depth and breadth of the activity. The CEE Initiative has provided opportunities to make a difference in the way Rockwell and NASA work together - to update the methods and processes of the organizations. The future success of NASA space programs and Rockwell hinges upon the ability to adopt new, more efficient and effective work processes. Efficiency, proficiency, cost effectiveness, and teamwork are a necessity for economic survival. Continuous improvement initiatives like the CEE are, and will continue to be, vehicles by which the road can be traveled with a vision to the future.

Bejmuk, Bohdan I.↗

Tether Fundamentals

Forces on tethered satellites, tether tension as a function of the effective mass, and parameters of candidate tether materials are examined. Illustrations show: stabilization control law; tethered satellite deployment and retrieval; angular momentum; electric motor effect reboost; a very long tether phenomenon; shuttle tethered satellite effects on the orbiter; artificial gravity; tethered satellite rendezvous docking relative velocity; and scaling up from the shuttle/TSS. Limitations of the tethered satellite system and of tether properties as well as cost/benefits trades for future applications are considered.

Rupp, C.↗

Reliability of Space-Shuttle Pressure Vessels with Random Batch Effects

In this article we revisit the problem of estimating the joint reliability against failure by stress rupture of a group of fiber-wrapped pressure vessels used on Space-Shuttle missions. The available test data were obtained from an experiment conducted at the U.S. Department of Energy Lawrence Livermore Laboratory (LLL) in which scaled-down vessels were subjected to life testing at four accelerated levels of pressure. We estimate the reliability assuming that both the Shuttle and LLL vessels were chosen at random in a two-stage process from an infinite population with spools of fiber as the primary sampling unit. Two main objectives of this work are: (1) to obtain practical estimates of reliability taking into account random spool effects and (2) to obtain a realistic assessment of estimation accuracy under the random model. Here, reliability is calculated in terms of a 'system' of 22 fiber-wrapped pressure vessels, taking into account typical pressures and exposure times experienced by Shuttle vessels. Comparisons are made with previous studies. The main conclusion of this study is that, although point estimates of reliability are still in the 'comfort zone,' it is advisable to plan for replacement of the pressure vessels well before the expected Lifetime of 100 missions per Shuttle Orbiter. Under a random-spool model, there is simply not enough information in the LLL data to provide reasonable assurance that such replacement would not be necessary.

Feiveson, Alan H.↗