Search NASA⌕ Search

SEARCH · Search NASA

Results for “spacecraft control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Transparent electrically conducting thin films for spacecraft temperature control applications

Thin transparent films of In2O3 or In2O3 + SnO2 prepared by evaporation or sputtering have been tested for use as surface layers for spacecraft temperature control coatings. The films are intended to prevent nonuniform electric charge buildup on the spacecraft exterior. Film thicknesses of 300 to 500 A were found to be optimal in terms of durability and minimum impact on the solar absorptance and the thermal emissivity of the underlayers. As a verification of their suitability for long-duration space missions, the films were subjected to simulated solar UV plus proton irradiation in a vacuum.

Hass, G.↗
NASA NTRS2004

Chapter 9: MEMS Applications in Spacecraft Thermal Control and Chapter 13: Handling and Contamination Control Considerations for Critical Space Applications

Thermal control systems (TCS) are an integral part of all spacecraft and instruments. To operate properly all spacecraft components must be maintained within a specified temperature band, which in some instances can be quite tight (less than 1 degree C). Traditionally this is accomplished by "passive" designs, but with modem spacecraft and instruments it is increasingly necessary to use active thermal control technologies. Microelectromechanical System (MEMS) can be useful in developing an active TCS, and may be especially useful for small spacecraft. As the MEMS knowledge matures, the applications of MEMS in spacecraft thermal control emerges as a viable technology for thermal engineers. Potential applications include specialized thermal control coatings, thermal switches, and specialized filters for instruments. Although MEMS technology demonstrates benefits, it also poses challenges for thermal en,oineers due to the lack of in-flight MEMS data. As a consequence, in order to design a MEMS thermal control device and receive the full advantage, it is important to understand the potential impact of the space environment on MEMS devices and the design/operational constraints imposed in their use. An entire chapter is devoted to handling and contamination controls for Micro Electro Mechanical Systems (MEMS) in space applications due to the importance of the topic area to final mission success. Handling and contamination control is discussed relative to the full life cycle from the very basic wafer level processing up through on orbit deployment. MEMS packaging will drive the need to tailor the Handling and Contamination Control Plan in order to assure adequacy of the overall program on a program by program basis. Plan elements are discussed at length to assist the user in preparing and implementing effective plans for both handling and contamination control to prevent deleterious effects.

Osiander, Robert↗
NASA NTRS2003

Tetrahedron Formation Control

Spacecraft flying in tetrahedron formations are excellent instrument platforms for electromagnetic and plasma studies. A minimum of four spacecraft - to establish a volume - is required to study some of the key regions of a planetary magnetic field. The usefulness of the measurements recorded is strongly affected by the tetrahedron orbital evolution. This paper considers the preliminary development of a general optimization procedure for tetrahedron formation control. The maneuvers are assumed to be impulsive and a multi-stage optimization method is employed. The stages include targeting to a fixed tetrahedron orientation, rotating and translating the tetrahedron and/or varying the initial and final times. The number of impulsive maneuvers citn also be varied. As the impulse locations and times change, new arcs are computed using a differential corrections scheme that varies the impulse magnitudes and directions. The result is a continuous trajectory with velocity discontinuities. The velocity discontinuities are then used to formulate the cost function. Direct optimization techniques are employed. The procedure is applied to the Magnetospheric Multiscale Mission (MMS) to compute preliminary formation control fuel requirements.

Guzman, Jose J.↗
NASA NTRS2004

Reconfigurable topologies for decentralized control of spacecraft formations in Deep Space

This paper discusses control and communication topologies that asynchronously distribute the sensing, communication and computation tasks amongst the spacecraft in the formation. Our approach allows the dynamic reconfiguration of the measurement and communication topologies while maintaining the specified formation performance objectives. An illustrative simulation example is presented.

Hadaegh, Fred Y.↗
NASA NTRS2005

Robust Load-Sharing Control of Spacecraft Formations

This paper focuses on the design of autonomous and collaborative control strategies to govern the relative distances among multiple spacecraft in formation with no ground intervention. A coordinate load-sharing control structure for formation flying and a methodology to control their dynamic models with slow time-varying and uncertain parameters are the main objectives of this work. The method is applied to a deep space formation example, where the uncertainty in spacecraft fuel masses is also considered.

multi spacecraft↗
NASA NTRS2022

Robust Controller Synthesis for Vision-based Spacecraft Guidance and Control

This work develops a method for Robust Controller for Vision-based Spacecraft (RCVS) guidance and control, integral to the robust autonomy framework for multi-spacecraft for- mation control and reconfiguration applications. The method is built around the use of a photo-realistic simulator, where a camera is deployed on a tracking spacecraft (ego) in order to observe an uncontrolled spacecraft (target) in a Low Earth Orbit (LEO). In this direction, the proposed approach performs the relative state (attitude and position) estimation of the target spacecraft using Convolutional Neural Network (CNN). The state estimation error is then modeled and the corresponding error-bounds are obtained around a nominal trajectory of the ego and target spacecraft. Next, this work proposes a linear matrix inequalities (LMIs) based approach to controller synthesis, guaranteed to be robust against both model uncertainties and measurement errors, resulting from vision-based estimation. This controller is comprised of two distinct components, one synthesized based on the nominal trajectory, while the “robust” component corrects for deviations from the nominal trajectory. Finally, a tracking scenario that directly utilize the image data for spacecraft guidance and control, is presented to showcase the performance of the proposed robust autonomy framework.

Rahmani, Amir↗
NASA NTRS1977

Evolution of Spacecraft Attitude Control Concepts Before 1952

The control of rotational motion of a spacecraft during its free flight regime is traced from pioneer space flight to the year 1952. Essentials of attitude control systems are reviewed and spin stabilization is examined. Other topics include passive stabilization and active closed loop control.

Robert E Roberson↗
NASA NTRS1993

Optimal periodic control for spacecraft pointing and attitude determination

A new approach to autonomous magnetic roll/yaw control of polar-orbiting, nadir-pointing momentum bias spacecraft is considered as the baseline attitude control system for the next Tiros series. It is shown that the roll/yaw dynamics with magnetic control are periodically time varying. An optimal periodic control law is then developed. The control design features a state estimator that estimates attitude, attitude rate, and environmental torque disturbances from Earth sensor and sun sensor measurements; no gyros are needed. The state estimator doubles as a dynamic attitude determination and prediction function. In addition to improved performance, the optimal controller allows a much smaller momentum bias than would otherwise be necessary. Simulation results are given.

Pittelkau, Mark E.↗
NASA NTRS2001

A Non-Linear Approach to Spacecraft Trajectory Control in the Vicinity of a Libration Point

An expanding interest in mission design strategies that exploit libration point regions demands the continued development of enhanced, efficient, control algorithms for station-keeping and formation maintenance. This paper discusses the development of a non-linear, station-keeping, control algorithm for trajectories in the vicinity of a libration point. The control law guarantees exponential convergence, based on a Lyaponov analysis. Controller performance is evaluated using FreeFlyer(R) and MATLAB(R) for a spacecraft stationed near the L2 libration point in the Earth-Moon system, tracking a pre-defined reference trajectory. Evaluation metrics are fuel usage and tracking accuracy. Simulation results are compared with a linear-based controller for a spacecraft tracking the same reference trajectory. Although the analysis is framed in the context of station-keeping, the control algorithm is equally applicable to a formation flying problem with an appropriate definition of the reference trajectory.

Luquette, Richard J.↗
NASA NTRS1965

LEM piloted control considerations.

LEM mission and pilot role in spacecraft control including guidance and control systems, retromaneuvering, landing-site inspection, etc

GUIDANCE AND CONTROL↗
NASA NTRS1989

New multivariable capabilities of the INCA program

The INteractive Controls Analysis (INCA) program was developed at NASA's Goddard Space Flight Center to provide a user friendly, efficient environment for the design and analysis of control systems, specifically spacecraft control systems. Since its inception, INCA has found extensive use in the design, development, and analysis of control systems for spacecraft, instruments, robotics, and pointing systems. The (INCA) program was initially developed as a comprehensive classical design analysis tool for small and large order control systems. The latest version of INCA, expected to be released in February of 1990, was expanded to include the capability to perform multivariable controls analysis and design.

Bauer, Frank H.↗
NASA NTRS1986

Nonlinear interfaces for acceleration-commanded control of spacecraft and manipulators

Nominal command generation in real time for the control of manipulators or of maneuvering spacecraft is hampered by the nonlinearity of the equations of motion. Likewise the real time tracking of a computed nominal trajectory in the presence of disturbances requires the computation of time-varying Jacobians of the motion. An alternative approach is the formulation of acceleration-commanded control laws in appropriately chosen generalized advantageous to design dedicated circuit interfaces to perform the required transformation. It is also possible to guarantee that actuator and sensor saturation limits are not exceeded, by means of feedback-biased circuits that implement automatic overload limitation of acceleration commands. Recent developments following this 'hardware computation' point of view will be discussed.

Dwyer, T. A. W., III↗
NASA NTRS2010

Transient Plume Model Testing Using LADEE Spacecraft Attitude Control System Operations

The Lunar Atmosphere Dust Environment Explorer (LADEE) spacecraft is being designed for a mission featuring low altitude orbits of the Moon to take relevant ambient measurements before that environment becomes altered by future exploration activities. Instruments include a neutral mass spectrometer capable of measuring ambient species density levels below 100 molecules/cu cm. Coincidentally, with a favorable combination of spacecraft orientations, it is also possible to measure plume gases from LADEE attitude control system thruster operations as they are reflected from the daytime lunar surface and subsequently intercepted by the spacecraft as it orbits overhead. Under such circumstances, it may be possible to test a variety of properties and assumptions associated with various transient plume models or to infer certain aspects regarding lunar surface properties.

Woronowicz, M. S.↗
NASA NTRS1998

An approach to the design and implementation of spacecraft attitude control systems

Over 39 years and a long list of missions, the guidance, navigation, and control (GN&C) groups at the Goddard Space Flight Center have gradually developed approaches to the design and implementation of successful spacecraft attitude control systems. With the recent creation of the Guidance, Navigation, and Control Center at Goddard, there is a desire to document some of these design practices to help to ensure their consistent application in the future. In this paper, we will discuss the beginnings of this effort, drawing primarily on the experience of one of the past attitude control system (ACS) groups at Goddard (what was formerly known as Code 712, the Guidance, Navigation, and Control Branch). We will discuss the analysis and design methods and criteria used, including guidelines for linear and nonlinear analysis, as well as the use of low- and high-fidelity simulation for system design and verification of performance. Descriptions of typical ACS sensor and actuator hardware will be shown, and typical sensor/actuator suites for a variety of mission types detailed. A description of the software and hardware test effort will be given, along with an attempt to make some qualitative estimates on how much effort is involved. The spacecraft and GN&C subsystem review cycles will be discussed, giving an outline of what design reviews are typically held and what information should be presented at each stage. Finally, we will point out some of the lessons learned at Goddard.

ODonnell, James R., Jr.↗