Search NASA⌕ Search

SEARCH · Search NASA

Results for “synthesis and processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Technology Strategy Assessment: Findings from Storage Innovations 2030 Bidirectional Hydrogen Storage

Hydrogen is the most common element in the universe, comprising nearly 75% of all normal matter, and it has been used by scientists for centuries, but it was not fully recognized as an element until 1766, when it was isolated by Henry Cavendish. Early work focused on the generation of hydrogen through the oxidation of metals in water, which released hydrogen gas. Hydrogen’s lighter-than-air and flammable properties were immediately used in engines, zeppelins, and as feedstock for a wide variety of chemical reactions. Several approaches were developed for the production of hydrogen with the most common being associated with the production and conversion of hydrocarbon-based fuels. Coal gasification, steam methane reforming, and other reformation processes provide the majority of current hydrogen production due to the relatively low cost of hydrogen produced through these processes. More than 95% of hydrogen production is used for industrial processes rather than energy storage. To facilitate affordable decarbonization of these industrial processes and to advance the use of hydrogen as a fuel in transportation, DOE launched the Hydrogen Shot as part of the Energy Earthshots Initiative. The goal of the Hydrogen Shot is to reduce the cost of clean hydrogen by 80% to $1/kg of clean hydrogen production within one decade (known as the “1 1 1” goal). This is distinct from the Long-Duration Storage Shot, which is the primary focus of this report; however, it is intrinsically linked to bidirectional hydrogen storage. Several important chemical synthesis processes are dependent upon hydrogen, and the production and use of hydrogen is generally driven by its connection to one of these markets. For example, ammonia is one of the most highly produced chemicals in the world and it depends chiefly on hydrogen. Ammonia is primarily used for agricultural fertilizer and is considered to be largely responsible for a doubling of agricultural production per unit of land over the last century. Another one of hydrogen’s primary uses is as a catalyst in petroleum refining during the desulfurization process. Beyond chemical production, hydrogen is used as a reductant in the production of steel and has been demonstrated as a substitute for metallurgical coal in the production of raw iron. It is even used in the hydrogenation reaction for food products to create more shelf-stable semi-solid fats. However, while hydrogen is produced on the order of 100 million metric tons/year globally to feed these industries, more than 95% of hydrogen is produced from hydrocarbons that emit CO2 during the process. Conversely, electrolysis is a process by which electricity is used to separate hydrogen and oxygen in water molecules, usually across a membrane. Hydrogen production via electrolysis lowers the carbon intensity of produced hydrogen when coupled with low-carbon electricity. Currently, global electrolysis capacity is on the order of 1 GW, which equates to about 500 metric tons/day of hydrogen production. To support large-scale industrial decarbonization, capacity will likely need to increase by two to three orders of magnitude. Electrolysis technology is broadly separated into groups that are defined by the electrolyte used, with further subdivision based on the operating characteristics. The majority of commercial electrolyzer systems are based around three main technology groups: liquid alkaline, proton exchange membrane, and solid oxide. Liquid Alkaline (LA) electrolysis is the oldest, most mature, least expensive, and most common commercial technology, with 400 plants in operation by 1902. Its hydrogen output is low relative to the size of the system due to a low current density. LA electrolysis utilizes a liquid potassium hydroxide solution as the electrolyte. Proton exchange membrane (PEM) electrolysis (also known as polymer electrolyte membrane electrolysis), described in 1960, relies on an acid-impregnated polymer membrane as the electrolyte and typically offers three to six times higher hydrogen production per unit cell area than LA electrolysis. Solid oxide electrolysis, or high-temperature electrolysis, utilizes a ceramic cell as the electrolyte and operates on steam rather than liquid water, enabling electrical efficiencies of more than 90%, which is up from 60% with PEM. Two pre-commercial electrolyzer technologies to note are alkaline exchange membrane (AEM) and proton-conducting solid oxide electrolysis cell (SOEC). AEM potentially has the advantages of both LA and PEM technologies in that it is able to use low-cost materials like LA but with the ability to operate at higher output pressures with a smaller footprint like PEM. Proton-conducting SOEC is similar to commercial SOEC, which uses an oxide-conducting ceramic; however, it uses a proton-conducting ceramic that has the potential to operate at lower temperatures and has lower capital costs. Each of these technologies is experiencing a rapid improvement in performance and a reduction in installed cost, and each appears to be well suited to specific applications. Besides differences in the type of electrolyzer used, the main difference in the architecture of bidirectional hydrogen systems is how the hydrogen is stored. Currently, the most cost-effective way to store large amounts of hydrogen gas is underground, such as in large salt caverns that have been hollowed out. These salt caverns are geographically concentrated in small portions of the United States and are not generally near large metropolitan areas; however, other subsurface architectures are being investigated to expand this reach. A more widely deployable option is aboveground pressurized tanks. These systems are about 10 times as expensive because of the materials and safety margins required to hold hydrogen at high pressures. A third option is using materials-based storage, such as liquid organic hydrogen carriers. By reversibly attaching the produced hydrogen to other molecules, it can be stored at near atmospheric pressure and room temperature. This has the potential to reduce the material cost of storage but may result in a reduction in the efficiency of the process because there are both hydrogen uptake and release processes. While materials-based storage has not been used extensively for large-scale hydrogen storage in the past, there is currently significant activity regarding developing materials and processes for use in large-scale hydrogen storage applications. Electrolysis-produced hydrogen offers an unusual opportunity for energy storage applications. Unlike more conventional energy storage approaches, such as batteries, which operate entirely within electrical markets, hydrogen is a valuable product beyond the electric market and can be directed to the most lucrative use. Hydrogen also can be directly converted back to electricity using either a fuel cell or turbine, or it can be sold to other markets, such as chemical synthesis, steel production, or even export. In this way, excess electricity can be upgraded to the most valuable product. Finally, its use can be actively managed between multiple off-takers; for example, local hydrogen storage can provide a specific amount of stored electricity and any excess can be exported to ammonia production. This flexibility is amplified by the fact that hydrogen storage has fully decoupled power and energy components, which allows for affordable scaling options. Together, this allows a substantial amount of creativity to enable the economic utilization of variable power resources while supporting decarbonization of the industry.

08 HYDROGEN↗

Novel High Efficient Organic Photovoltaic Materials

Solar energy is a renewable, nonpolluting, and most abundant energy source for human exploration of a remote site or outer space. In order to generate appreciable electrical power in space or on the earth, it is necessary to collect sunlight from large areas and with high efficiency due to the low density of sunlight. Future organic or polymer (plastic) solar cells appear very attractive due to their unique features such as light weight, flexible shape, tunability of energy band-gaps via versatile molecular or supramolecular design, synthesis, processing and device fabrication schemes, and much lower cost on large scale industrial production. It has been predicted that supramolecular and nano-phase separated block copolymer systems containing electron rich donor blocks and electron deficient acceptor blocks may facilitate the charge carrier separation and migration due to improved electronic ultrastructure and morphology in comparison to polymer composite system. This presentation will describe our recent progress in the design, synthesis and characterization of a novel block copolymer system containing donor and acceptor blocks covalently attached. Specifically, the donor block contains an electron donating alkyloxy derivatized polyphenylenevinylene (RO-PPV), the acceptor block contains an electron withdrawing alkyl-sulfone derivatized polyphenylenevinylene (SF-PPV). The key synthetic strategy includes the synthesis of each individual block first, then couple the blocks together. While the donor block has a strong PL emission at around 560 nm, and acceptor block has a strong PL emission at around 520 nm, the PL emissions of final block copolymers are severely quenched. This verifies the expected electron transfer and charge separation due to interfaces of donor and acceptor nano phase separated blocks. The system therefore has potential for variety light harvesting applications, including high efficient photovoltaic applications.

Sun, Sam↗

TiO{sub 2} nanorods branched on fast-synthesized large clearance TiO{sub 2} nanotube arrays for dye-sensitized solar cells

A large clearance TiO{sub 2} nanotube arrays (LTAs) has been synthesized by a not more than 12 h anodization duration and based on this a branched TiO{sub 2} nanotube arrays (BLTs) has been achieved through TiO{sub 2} nanorods branch-like grown on the LTAs. Some key factors and probable mechanisms of the fabrication processes on two novel nanoarchitectures are discussed. Exhilaratingly, it is found that the obtained LTAs has demonstrated large pore diameter and void spaces (pore diameter {approx}350 nm; void spaces {approx}160 nm; and tube length {approx}3.5 {mu}m), and the synthesized hierarchical BLTs, compared with conventional TiO{sub 2} nanotube arrays, has shown a much stronger dye absorption performance and an approximately double of the solar cell efficiency (in our case from 1.62% to 3.18% under simulated AM 1.5 conditions). - Graphical Abstract: The schematic diagram of synthesis process for LTAs and BLTs is on the above and the corresponding FESEM images of obtained photoanodes samples are shown below. Highlights: > Large clearance TiO{sub 2} nanotube arrays (LTAs) was synthesized by a fast anodization process of 12 h. > Anodization time of 12 h is just 10% of about 120 h reported in the previous references. > Branch-like TiO{sub 2} nanotube arrays (BLTs) was achieved by growing TiO{sub 2} nanorods on the LTAs. > Obtained BLTs and LTAs show impressive morphology and noticeable improvement of surface area. > BLTs shows about more than 1 times higher solar cell efficiency than that of TiO{sub 2} nanotube arrays.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis of zeolite from Italian coal fly ash: Differences in crystallization temperature using seawater instead of distilled water

In this study Italian coal fly ash was converted into several types of zeolite in laboratory experiments with temperatures of crystallization ranging from 35 up to 90 deg. C. Distilled and seawater were used during the hydrothermal synthesis process in separate experiments, after a pre-treatment fusion with NaOH. The results indicate that zeolites could be formed from different kind of Italian coal fly ash at low temperature of crystallization using both distilled and seawater. SEM data and the powder patterns of X-ray diffraction analysis show that faujasite, zeolite ZK-5 and sodalite were synthesized when using both distilled and seawater; zeolite A crystallized only using distilled water. In particular the experiments indicate that the synthesis of zeolite X and zeolite ZK-5 takes place at lower temperatures when using seawater (35 and 45 deg. C, respectively). The formation of sodalite is always competitive with zeolite X which shows a metastable behaviour at higher temperatures (70-90 deg. C). The chemical composition of the fly ash source could be responsible of the differences on the starting time of synthesized zeolite with distilled water, in any case our data show that the formation of specific zeolites takes place always at lower temperatures when using seawater.

36 MATERIALS SCIENCE↗

Tuning 3-D Nanomaterial Architectures Using Atomic Layer Deposition to Direct Solution Synthesis

The ability to synthesize nanoarchitected materials with tunable geometries provides a means to control their functional properties, with applications in biological, environmental, and energy fields. To this end, various bottom-up and top-down synthesis processes have been developed. However, many of these processes require prepatterning or etching steps, making them challenging to scale-up to complex, nonplanar substrates. Furthermore, the ability to integrate nanomaterials into hierarchical arrays with precise control of feature spacing and orientation remains a challenge. One approach to overcome these patterning challenges is the use of surface modification layers to guide the resulting geometry of nanomaterial architectures grown from the substrate. A powerful strategy to accomplish this is what we will refer to as “surface-directed assembly,” where the resulting geometric parameters (feature size, shape, orientation) are predetermined by the initial surface layer. In particular, the use of Atomic Layer Deposition (ALD) to form a surface layer, followed by solution-based growth processes, has the ability to synthesize architected structures with tunable geometries on complex, nonplanar surfaces. Over the past decade, we have reported a series of studies where surface-directed assembly is used to synthesize ZnO nanowires (NWs) on top of a variety of substrates. In this case, a thin film of ZnO is deposited onto the substrate using ALD, which can guide the NW diameter, spacing, and angular orientation with respect to the substrate by controlling epitaxial relationships. Furthermore, we have shown that by depositing a submonolayer overcoat of a secondary material (e.g., amorphous TiO 2 ), nucleation sites are partially blocked, which can further tune the spacing between nanowires while minimizing changes to their other geometric properties. This approach can be used to generate multilevel hierarchical structures, such as hyperbranched NW arrays with tunable control of each level of hierarchy using ALD. Finally, we have demonstrated that the tunable control of geometric parameters can be scaled-up to curved, nonplanar substrates. This highlights the power of ALD to conformally and uniformly deposit the seed layers on complex substrates with subnanometer precision. To complement these seeded hydrothermal approaches, we expanded this strategy to include conversion chemistry of the initial ALD seed layers. For example, by replacing ZnO with Al 2 O 3 as the seed layer without changing the hydrothermal growth conditions, Al–Zn layered-double hydroxide nanosheets can be formed instead of nanowires. In another example of conversion chemistry, a solution anion-exchange process was used to incorporate sulfur into ALD metal oxide films. In both of these conversion processes, the properties of the initial ALD film enabled tuning of the resulting nanostructure geometry. In this Account, we describe the use of ALD to guide the growth of diverse nanomaterial systems, with tunable control over their geometry and composition. We further show how these approaches can be used to tune functional properties for a range of applications, including superomniphobic surfaces, antibiofouling coatings, and photocatalysis. In conclusion, we conclude with an outlook on how the combination of ALD and solution synthesis can enable future directions in scalable nanomanufacturing to overcome the limitations of traditional top-down and bottom-up approaches.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Synthesis Plugin for Auralization of Rotor Self Noise

This paper describes the development and architecture of a software plugin for the NASA Auralization Framework that synthesizes rotor modulating broadband self noise. A conceptual overview of the synthesis process is reviewed. The architecture description includes use of the plugin within a broader framework to auralize rotorcraft flyovers. Use of the plugin is demonstrated for a six-passenger quadrotor urban air mobility reference vehicle design using collective-pitch control.

Self Noise↗

Electrochemical Li intercalation in b-As y P 1–y alloys: In-situ Raman spectroscopy study

Structural evolution of b-As y P 1-y alloys with varying As concentration, y was studied during Li-intercalation using in-situ Raman spectroscopy. A monotonic redshift of all the vibrational modes corresponding to P-P bonds (A 1 g , A 2 g , B 2g ), As-As bonds (A 1 g , A 2 g , B 2g ), and As-P bonds of all the samples was observed during the initial stages of the intercalation process due to the softening of each mode caused by the intercalation driven donor-type charge-transfer from Li to b-As y P 1-y . The emergence of a new peak identified as the E g mode of gray As, above an intercalation threshold, is indicative of the presence of an intercalation-driven structural phase segregation process. Further, the A 1g mode of gray As emerging after this intercalation threshold lies in close proximity of the A 2 g Raman mode of b-As y P 1-y . All the peaks beyond the intercalation threshold show an upshift due to the co-existence of gray As with b-As y P 1-y alloys causing strain and thus hardening of the phonon modes. In the sample with the highest As concentration phase segregation takes place during the synthesis process. Computational modeling reveals the co-existence of gray As in the b-As y P 1-y alloys with high As concentrations. It also confirms the existence of a local structural segregation taking place at a critical Li concentration during the intercalation process. Furthermore, this work shows the significance of intercalation on structural changes in the search for new phases of b-As y P 1-y alloys.

2D Materials↗

Structural stability and mutual transformations of molybdenum carbide, nitride and phosphide

Graphical abstract: Both Mo{sub 2}C and Mo{sub 2}N can be transformed to MoP, whereas the reverse changes are inviable, which is used to develop a promising and practical pathway for preparing MoP nanoparticles. Highlights: {yields} Mo carbide, nitride and phosphide are prepared. {yields} The structural stability increases in the order of Mo{sub 2}N < Mo{sub 2}C < MoP. {yields} Both Mo{sub 2}C and Mo{sub 2}N can be transformed to MoP, whereas the reverse changes are inviable. {yields} This study develops a promising and practical pathway for preparing MoP nanoparticles. -- Abstract: The structural stability and transformations of Mo carbide, nitride and phosphide were investigated under various atmosphere conditions by X-ray diffraction (XRD). The results indicated that the order of structural stability of these Mo-based compounds was as follows: Mo{sub 2}N < Mo{sub 2}C < MoP. Both Mo{sub 2}C and Mo{sub 2}N can be transformed to MoP, whereas the reverse transformations did not occur. Noticeably, compared with those Mo sources containing oxygen, the use of Mo{sub 2}C/Mo{sub 2}N as Mo-source can produce finely dispersed MoP nanoparticles by the temperature-programmed reaction (TPR) method. The result was probably due to the fact that lower-levels H{sub 2}O generated during synthesis process can avoid strong hydrothermal sintering. The influence of formation energy had been considered and was found to relate to the structural stability and transformations of these Mo-based compounds.

36 MATERIALS SCIENCE↗

Ternary and Quaternary Nickel-Iron-Oxide-Based Thin Films as Oxygen Evolution Reaction Catalysts in Alkaline Media

Alkaline water electrolyzers are a promising technology for energy storage and conversion through the electrochemical production of hydrogen, however the slow kinetics of the oxygen evolution reaction (OER) pose a major challenge. The alkaline environment enables the use of non-Pt-group metals as OER catalysts, in particular NiFe-based materials. In this study, Mn and/or Cr were elementally mixed with NiFe to further improve the OER catalyst properties through a controlled, systematic synthesis process involving thin films prepared by electron beam-induced physical vapor deposition (PVD). By exploring both simultaneous co-deposition and serial deposition of the different metals, the OER performance was investigated as a function of both the location of Mn or Cr in the multi-metal NiFe-based catalysts and the difference between surface versus bulk mixing. The distinct differences in the redox dynamics, surface oxidation, and stability of the seven studied catalysts reveal metal Cr- and/or Mn-overlayers as a promising synthesis approach for fine-tuning of catalyst properties and improving the OER performance.

Alkaline Water Electrolysis↗

A Synthesis Plugin for Auralization of Rotor Self Noise

This paper describes the development and architecture of a software plugin for the NASA Auralization Framework that synthesizes rotor modulating broadband self noise. A conceptual overview of the synthesis process is reviewed. The architecture description includes use of the plugin within a broader framework to auralize rotorcraft flyovers. Use of the plugin is demonstrated for a six-passenger quadrotor urban air mobility reference vehicle design using collective-pitch control.

Auralization↗

Advancing the Performance of Lithium-Rich Oxides in Concert with Inherent Complexities: Domain-Selective Substitutions

Historically, modifications to Li- and Mn-rich (LMR) cathodes have been studied in relation to their efficacy in solving challenges such as oxygen loss and voltage fade, which are inherent to the activation process of these electrodes. However, even in the presence of these phenomena, well-optimized LMR cathodes show considerable promise as earth-abundant options, particularly if other barriers to implementation can be overcome or mitigated. As the complex mechanisms of LMR electrodes are known to stem from the local, chemical inhomogeneities that define the nanocomposite domain nature of these oxides, strategies aimed at manipulating the performance of activated electrodes, irrespective of voltage fade, through domain-selective modifications, could prove instructive. In this work, we use a novel synthesis process aimed at influencing the site occupancy of substituted Sn 4+ , as an example 4+ cation, into a Co-free Li 1.13 Mn 0.57(1–x) Sn 0.57x Ni 0.3 O 2 LMR oxide. We show that Sn 4+ can be selectively substituted into Li-rich environments. The consequences are revealed to be both chemical and morphological, and the domain-selective doping strategy provides a knob for directed control of the low state-of-charge impedance behavior. In conclusion, these results reveal new clues and insights with respect to further advancing the practical relevance of LMR cathode particles and electrodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of calcination temperature on the photocatalytic activity of TiO{sub 2} powders prepared by co-precipitation of TiCl{sub 3}

The adsorption of basic dye methylene blue (MB) onto titanium dioxide (titania) powder that were prepared by coprecipitation method of TiCl{sub 3} and NH{sub 4}OH as iniatial material with different calcination temperature was studied to examine the photocatalytic activity. Synthesis process carried out by the solution pH was adjusted to be 8. Effect of calcination temperature on the titania powder were characterized with Differential Scanning Calorimetry/Thermogravimetry (DSC/TG), X-ray diffraction (XRD), and Scanning Electron Microscopy (SEM). The result of TG and XRD showed that the NH{sub 4}Cl decomposed between 235-372°C. The XRD result showed that the anatase TiO{sub 2} only contained a single phase when the calcination temperature of the precursor at 800°C, and over which it began to grow rutile phase. The influence of synthesis condition on the photocatalytic activity of TiO{sub 2} powder was determined by the photodegradation of MB dye under UV light.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

In situ analysis of elemental depth distributions in thin films by combined evaluation of synchrotron x-ray fluorescence and diffraction

In this work we present a method for the in situ analysis of elemental depth distributions in thin films using a combined evaluation of synchrotron x-ray fluorescence and energy-dispersive x-ray diffraction signals. We recorded diffraction and fluorescence signals simultaneously during the reactive annealing of thin films. By means of the observed diffraction signals, the time evolution of phases in the thin films during the annealing processes can be determined. We utilized this phase information to parameterize the depth distributions of the elements in the films. The time-dependent fluorescence signals were then taken to determine the parameters representing the parameterized depth distributions. For this latter step, we numerically calculated the fluorescence intensities for a given set of depth distributions. These calculations handle polychromatic excitation and arbitrary functions of depth distributions and take into account primary and secondary fluorescence. Influences of lateral non-uniformities of the films, as well as the accuracy limits of the method, are investigated. We apply the introduced method to analyze the evolution of elemental depth distributions and to quantify the kinetic parameters during a synthesis process of CuInS{sub 2} thin films via the reactive annealing of Cu-In precursors in a sulfur atmosphere.

36 MATERIALS SCIENCE↗

Mechanism of Synthesis of Ultra-Long Single Wall Carbon Nanotubes in Arc Discharge Plasma

In this project fundamental issues related to synthesis of single wall carbon nanotubes (SWNTs), which is relationship between plasma parameters and SWNT characteristics were investigated. Given that among plasma-based techniques arc discharge stands out as very advantageous in several ways (fewer defects, high flexibility, longer lifetime) this techniques warrants attention from the plasma physics and plasma technology standpoint. Both experimental and theoretical investigations of the plasma and SWNTs synthesis were conducted. Experimental efforts focused on plasma diagnostics, measurements of nanostructures parameters, and nanoparticle characterization. Theoretical efforts focused to focus on multi-dimensional modeling of the arc discharge and single wall nanotube synthesis in arc plasmas. It was demonstrated in experiment and theoretically that controlling plasma parameters can affect nanostucture synthesis altering SWNT properties (length and diameter) and leading to synthesis of new structures such as a few-layer graphene. Among clearly identified parameters affecting synthesis are magnetic and electric fields. Knowledge of the plasma parameters and discharge characteristics is crucial for ability to control synthesis process by virtue of both magnetic and electric fields. New graduate course on plasma engineering was introduced into curriculum. 3 undergraduate students were attracted to the project and 3 graduate students (two are female) were involved in the project. Undergraduate student from Historically Black University was attracted and participated in the project during Summer 2010.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Novel Attrition-Resistant Fischer Tropsch Catalyst

There is a strong national interest in the Fischer-Tropsch synthesis process because it offers the possibility of making liquid hydrocarbon fuels from reformed natural gas or coal and biomass gasification products. This project explored a new approach that had been developed to produce active, attrition-resistant Fischer-Tropsch catalysts that are based on glass-ceramic materials and technology. This novel approach represented a promising solution to the problem of reducing or eliminating catalyst attrition and maximizing catalytic activity, thus reducing costs. The technical objective of the Phase I work was to demonstrate that glass-ceramic based catalytic materials for Fischer-Tropsch synthesis have resistance to catalytic deactivation and reduction of particle size superior to traditional supported Fischer-Tropsch catalyst materials. Additionally, these novel glass-ceramic-based materials were expected to exhibit catalytic activity similar to the traditional materials. If successfully developed, the attrition-resistant Fischer-Tropsch catalyst materials would be expected to result in significant technical, economic, and social benefits for both producers and public consumers of Fischer-Tropsch products such as liquid fuels from coal or biomass gasification. This program demonstrated the anticipated high attrition resistance of the glass-ceramic materials. However, the observed catalytic activity of the materials was not sufficient to justify further development at this time. Additional testing documented that a lack of pore volume in the glass-ceramic materials limited the amount of surface area available for catalysis and consequently limited catalytic activity. However, previous work on glass-ceramic catalysts to promote other reactions demonstrated that commercial levels of activity can be achieved, at least for those reactions. Therefore, we recommend that glass-ceramic materials be considered again as potential Fischer-Tropsch catalysts if it can be demonstrated that materials with adequate pore volume can be produced. During the attrition resistance tests, it was learned that the glass-ceramic materials are very abrasive. Attention should be paid in any further developmental efforts to the potential for these hard, abrasive materials to damage reactors.

01 COAL, LIGNITE, AND PEAT↗

Supercritical preparation of doped (111) facetted nickel oxide for the oxygen evolution reaction

Green hydrogen is of great interest as a replacement for traditional fossil fuels in a variety of energy applications. However, due to the poor kinetics present in the oxygen evolution reaction (OER) half-reaction, nanostructured catalysts are needed to reduce the reaction overpotential. Nickel oxide has previously been shown to be a promising alternative to expensive Pt-group based catalysts for the OER in alkaline media. Herein, facetted NiO nanosheets have been doped with Fe, Mn, or Co to reduce its catalytic overpotential for the OER. A supercritical synthesis process was used to promote the mass transport of the reactants while preserving catalytic surface area. Microscopy, diffraction, spectroscopy, and adsorption techniques were used to understand the morphological changes resulting from the inclusion of each dopant, as well as characterize the surface chemistry presented by the doped (111) facet. The pH was found to affect the properties of mixing due to difference in hydrolysis rates and catalysis of the hydrolysis/condensation. The dopants exhibited distinct effects on OER activity: Mn increased the overpotential to 742 mV vs. RHE, while Co and Fe reduced it to 502 mV and 457 mV, respectively. In summary, a straightforward and novel synthesis method is presented to prepare doped NiO(111) nanosheets, and their surface characteristics are explored to understand their varied electrochemical performances.

08 HYDROGEN↗

Multiscale Computational Model for Particle Size Evolution during Coprecipitation of Li-Ion Battery Cathode Precursors

Next generation lithium ion batteries require higher energy and power density, which can be achieved by tailoring the cathode particle morphology, such as particle size, size distribution, and internal porosity. All these morphological features are determined during the cathode synthesis process, which consists of two steps, (i) coprecipitation and (ii) calcination. Transition metal hydroxide precursors are synthesized during the coprecipitation process, whereas their oxidation and lithiation occur during calcination. The size and size distribution of crystalline primary and aggregated secondary particles and their internal porosity are determined during coprecipitation. Operating conditions of the chemical reactor, such as solution pH, ammonia concentration, and stirring speed control the final morphological features. Here, a multiscale computational model has been developed to capture the nucleation and growth of crystalline primary particles and their aggregation into secondary transition metal hydroxide precursor particles. The simulations indicate that increasing solution pH and decreasing ammonia concentration lead to smaller sizes of the secondary particles. Finally, a phase map has been developed that can help identify the synthesis conditions needed for a specified particle size and size distribution.

25 ENERGY STORAGE↗

Synthesis and characterization of nanocrystalline Ni-YSZ cermet anode for SOFC

Ni-YSZ cermet anode has been synthesized in one step using a simple and cost effective combustion synthesis process. The processed powder of NiO-YSZ is found to be nanocrystalline with crystallite sizes of 29 and 22 nm for NiO and YSZ respectively by X-ray diffraction and transmission electron microscopy analysis. X-ray diffraction analysis also shows that the precursor salts are converted to highly crystalline phases of NiO and YSZ (8 mol% Y{sub 2}O{sub 3}) without any intermediate calcination step and no undesirable phases are present. Comparison with the X-ray diffraction pattern of a commercial YSZ sample shows that the process is also effective in maintaining a close compositional control. The microstructure of the sintered and reduced sample shows a well defined network of pores which is necessary for the effective functioning of the anode. The electrical conductivity as a function of temperature shows metallic behavior.

36 MATERIALS SCIENCE↗