SEARCH · Search NASA

Results for “tensile behavior”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

DOE OSTI2026

A solid-state extrusion pathway extensible to upcycling aluminum scrap and end-of-life permanent magnets into ductile Al-6061/SmCo 5 structural magnetic composites

Permanent magnets offer strong potential for multifunctional structural components, but their inherent brittleness limits direct integration. Here, SolidStir® Extrusion (SSE) is used to embed SmCo5 powder into AA6061 in the solid state, and the resulting microstructure, interfacial chemistry, mechanical properties, and magnetic response are systematically characterized. SSE fragments the initial SmCo 5 powder into predominantly fine particles dispersed within an ultrafine Al matrix, with a volume fraction of ∼ 4–6 % in this proof-of-concept study. Interfacial reactions form a continuous Al–Co reaction layer, with local atomic-resolution indexing consistent with Al 13 Co 4 , together with Sm–Si-rich reaction products, while the matrix contains Sm–Co–Si-rich precipitates and Mg 2 Si, producing features from nanometers to micrometers. Compared with an Al extrudate, this architecture increases yield strength by ∼ 42 % and tensile strength by ∼ 31 %, while preserving uniform elongation, and it sustains work hardening in compression from 150 to 400 °C. The composite retained hard-magnetic behavior, with axial magnetization of 12.7 A·m 2 kg −1 at 6 T and intrinsic coercivity of 9.6 kOe. These findings demonstrate that SSE can produce Al-based load-bearing magnetic composites while preserving useful SmCo5 functionality.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Bicontinuous nanoporous design induced homogenization of strain localization in metallic glasses

Bicontinuous nanoporous metallic glasses (MG) synergize the outstanding properties of MGs and open-cell nanoporous materials. The low-density and high-specific-surface-area of bicontinuous nanoporous structures have the potential to enhance the applicability of MGs in catalysis, sensors, and lightweight structural designs. In this work, we report molecular dynamics simulations of tensile loading deformation and failure of bicontinuous nanoporous Cu 64 Zr 36 MG with 55% porosity and 4.4 nm ligament size. Results indicate an anomalous mechanical behavior featuring delocalized plastic deformation preceding ductile failure. The deformation follows two mechanisms: i) Necking of ligaments aligned with the loading direction and ii) progressive alignment of randomly oriented ligaments. Failure occurs at 0.16 strain, following massive rupture of ligaments. This work indicates that a bicontinuous nanoporous design is able to effectively delocalize strain localization in a MG due to a combination of size effect on the ductility of MGs resulting in nano ligaments necking and progressive asynchronous alignment of ligaments.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Kink bands promote exceptional fracture resistance in a NbTaTiHf refractory medium-entropy alloy

Single-phase body-centered cubic (bcc) refractory medium- or high-entropy alloys can retain compressive strength at elevated temperatures but suffer from extremely low tensile ductility and fracture toughness. We examined the strength and fracture toughness of a bcc refractory alloy, NbTaTiHf, from 77 to 1473 kelvin. This alloy’s behavior differed from that of comparable systems by having fracture toughness over 253 MPa·m 1/2 , which we attribute to a dynamic competition between screw and edge dislocations in controlling the plasticity at a crack tip. Whereas the glide and intersection of screw and mixed dislocations promotes strain hardening controlling uniform deformation, the coordinated slip of <111> edge dislocations with {110} and {112} glide planes prolongs nonuniform strain through formation of kink bands. These bands suppress strain hardening by reorienting microscale bands of the crystal along directions of higher resolved shear stress and continually nucleate to accommodate localized strain and distribute damage away from a crack tip.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Evaluation of the Mechanical Properties of Cast and Wrought CF8C-Plus Relevant to ASME Code Case Qualification

The mechanical behavior of a cast form of an advanced austenitic stainless steel, CF8C-Plus, is compared with that of its wrought equivalent in terms of both tensile and creep-rupture properties and estimated allowable stress values for pressurized service at temperatures up to about 850°C. A traditional Larson-Miller parametric model is used to analyze the creep-rupture data and to predict long-term lifetimes for comparison of the two alloy types. The cast CF8C-Plus exhibited lower yield and tensile strengths, but higher creep strength compared to its wrought counterpart. Two welding methods, shielded-metal-arc welding (SMAW) and gas-metal-arc welding, met the weld qualification acceptance criteria in ASME BPVC Section IX for the cast CF8C-Plus. However, for the wrought CF8C-Plus, while SMAW and gas-tungsten-arc welding passed the tensile acceptance criteria, they failed the side bend tests due to lack of fusion or weld metal discontinuities.

Chen, Xiang↗

DOE OSTI2020

Dynamic Tensile Response of a Fe–49Co–2V Alloy at Various Strain Rates and Temperatures

Soft ferromagnetic alloys are often utilized in electromagnetic applications due to their desirable magnetic properties. In support of these applications, the ferromagnetic alloys are also required to bear mechanical load under various loading and environmental conditions. In this study, a Fe–49Co–2V alloy was dynamically characterized in tension with a Kolsky tension bar and a Drop–Hopkinson bar at various strain rates and temperatures. Dynamic tensile stress–strain curves of the Fe–49Co–2V alloy were obtained at strain rates ranging from 40 to 230 s -1 and temperatures from - 100 to 100 °C. All dynamic tensile stress–strain curves exhibited an initial linear elastic response to an upper yield followed by Lüders band response and then a nearly linear work-hardening behavior. The yield strength of this material was found to be sensitive to both strain rate and temperature, whereas the hardening rate was independent of strain rate or temperature. The Fe–49Co–2V alloy exhibited a feature of brittle fracture in tension under dynamic loading with no necking being observed.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Ordering effects on deformation substructures and strain hardening behavior of a CrCoNi based medium entropy alloy

Here, a CrCoNi based medium entropy alloy with small additions of Ti, Al and Nb (denoted as (CrCoNi) 93 Al 4 Ti 2 Nb) in the as-quenched condition, exhibits tensile properties comparable to those of the equiatomic CrCoNi alloy at room temperature. Dark field transmission electron microscopy (TEM), atomic resolution high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) together with atom probe tomography (APT) show that spatially-localized long range ordering (LRO) L1 2 domains exist in this alloy. The evolution of deformation substructure with plastic deformation in this alloy was characterized using electron backscatter diffraction (EBSD), electron channeling contrast imaging (ECCI) and STEM based techniques including the recently developed weak beam dark field STEM imaging. Plastic deformation occurs by the slip of a/2<110>dislocations, which are narrowly dissociated into Shockley partial dislocations on {111} slip planes. Their dissociation distances in the (CrCoNi) 93 Al 4 Ti 2 Nb alloy are much smaller than the widths of the corresponding partials in the equiatomic CrCoNi alloy due to one or more of the minor alloying elements (Al, Ti, Nb). Dislocation slip in this alloy has a pronounced planar character. The leading dislocations in slip bands glide as pairs due to the existence of LRO domains. Multipoles were formed through the slip of dislocations with opposite signs on adjacent {111} slip planes. Those multipoles serve as building blocks for the formation of subgrain structures consisting of fine slip bands. The distances between slip bands were continuously refined during plastic deformation and dynamic refinement of slip bands plays a crucial role in strain hardening. The effects of LRO domains on planar dislocation slip, the deactivation of deformation twinning and strain hardening of this alloy are discussed.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Engineering hybrid textile braids for tendon and ligament repair application

Abstract Challenges involving tendon and ligament repair have motivated the investigation of new strategies to improve clinical outcomes. These have been mainly based on polymer constructs, which may be non‐biodegradable or biodegradable. The former typically fails due to lack of device integration and the latter demands a complex balance between biodegradability and tissue ingrowth, often failing due to insufficient mechanical properties. This work presents the development of hybrid braids based on polyethylene terephthalate (PET) and polylactic acid (PLA) yarns. A textile technique was used to fabricate braids based on 16 multifilament yarns of varying PLA/PET composition. The composition was varied to maximize biodegradability while ensuring mechanical performance. The braids' morphology, physical and mechanical properties were characterized. As production parameters and architecture were maintained, the braids exhibited similar porosity and wicking ability. The breaking force and stiffness decreased significantly as the number of PLA yarns increased, although strain levels remained constant. Braids containing 10 and 12 PET yarns (out of the total 16 yarns) demonstrated good creep and force‐relaxation behavior, as well as resistance to cyclic loading. These compositions were selected for future work, to be assembled into more elaborate structures to mimic the fibrous organization and tensile properties of different tendons/ligaments.

Peixoto, Tânia↗

DOE OSTI2023

Polyester-based epoxy vitrimer integrating spent coffee ground as a natural filler

Coffee is a widely consumed beverage, but approximately 80% mass of coffee cherry is discarded as waste. Here, in this study, spent coffee grounds (SCG) were recycled and used as a natural filler in a polyester-based epoxy matrix made from reactions of diglycidyl ethers of Bisphenol A and polyethylene glycol with methyl nadic anhydride. The properties of SCG/epoxy composites with various SCG contents up to 40% w/w were evaluated using various techniques such as FT-IR spectroscopy, tensile testing, optical microscopy, differential scanning calorimetry, and rheology. The SCG filled polyester-based epoxy matrix demonstrated excellent dimensional stability and retained a permanently crosslinked network, but re-shaping was possible at ~150 °C through transesterification, which occurred due to a dynamic chain exchange reaction between the ester group of the epoxy matrix and the hydroxyl group of the SCG fillers. The transesterification also improved the interfacial adhesion between the matrix and SCG fillers, resulting in tensile strength of over 20 MPa and a modulus of around 2.5 GPa, even with high SCG contents up to 40% w/w. While neat, cured epoxy shows thermoset behavior, filling the matrix with SCG enables reforming and origami-inspired spontaneous change in shape.

42 ENGINEERING↗

DOE OSTI2022

In-situ neutron diffraction investigation of two-stage martensitic transformation in a 13%Mn steel with serrated deformation

Two stage austenite →ε-martensite →α-martensite phase transformation, phase-specific lattice strain evolution and load sharing during tensile deformation of a 13%Mn hot-rolled austenitic steel are revealed by in-situ neutron diffraction. In conclusion, direct evidence is provided that serrated deformation behavior is attributed to discontinuous martensitic transformation.

Austenitic steel↗

DOE OSTI2024

Impact of anisotropy on TRISO fuel performance

Manufacturing of tristructural isotropic (TRISO) particles involves the deposition of pyrolytic carbon (PyC) and silicon carbide (SiC) layers using the fluidized bed chemical vapor deposition (CVD) process. The CVD process is known to generate polycrystalline layers with crystallographic textures, which imparts anisotropic thermophysical properties to the layers. Past studies have shown the risk for particle failure increases with an increase in anisotropy. The limit beyond which the anisotropy of PyC layers becomes unacceptable due to failure risk has been identified as a high-priority knowledge gap. This work presents a first systematic study on the effects of anisotropic thermal and mechanical properties on TRISO fuel performance. This computational study, performed using the fuel performance code BISON, investigates how the anisotropy in elasticity and thermal properties affect the stresses, temperature, and failure of a TRISO particle. The influence of other factors, such as operating temperature and particle geometry on the anisotropy effects, also has been analyzed. The studies utilize the recently published anisotropic elasticity and thermal behavior models for TRISO PyC and SiC layers implemented using tensors with full anisotropic capability. The spherical TRISO particles with anisotropic properties were found to have greater maximum tensile stress and significantly higher failure probability than the spherical particles with isotropic properties. In conclusion, the fuel performance predicted using these recently developed models was found to be comparable with the performance obtained using the historical models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Assessment of four strain energy decomposition methods for phase field fracture models using quasi-static and dynamic benchmark cases

Abstract Strain energy decomposition methods in phase field fracture models separate strain energy that contributes to fracture from that which does not. However, various decomposition methods have been proposed in the literature, and it can be difficult to determine an appropriate method for a given problem. The goal of this work is to facilitate the choice of strain decomposition method by assessing the performance of three existing methods (spectral decomposition of the stress or the strain and deviatoric decomposition of the strain) and one new method (deviatoric decomposition of the stress) with several benchmark problems. In each benchmark problem, we compare the performance of the four methods using both qualitative and quantitative metrics. In the first benchmark, we compare the predicted mechanical behavior of cracked material. We then use four quasi-static benchmark cases: a single edge notched tension test, a single edge notched shear test, a three-point bending test, and a L-shaped panel test. Finally, we use two dynamic benchmark cases: a dynamic tensile fracture test and a dynamic shear fracture test. All four methods perform well in tension, the two spectral methods perform better in compression and with mixed mode (though the stress spectral method performs the best), and all the methods show minor issues in at least one of the shear cases. In general, whether the strain or the stress is decomposed does not have a significant impact on the predicted behavior.

Zhang, Shuaifang↗

DOE OSTI2025

Bacterial-Retted Hemp Fiber/PLA Composites

The push for sustainability in all facets of manufacturing has led to an increased interest in biomass as an alternative to non-renewable materials. Hemp bast fiber mats were produced from a bacterial retting process, named BFM, as the fiber reinforcement. The objective of this study was to evaluate the feasibility of laminating BFM with polylactic acid (PLA) for a composite panel product. Since both BFM and PLA are biodegradable, the resulting BFM-PLA composites will be 100% biodegradable. PLA pallets were processed into thin polymer sheets which served as the matrix. The BFM and PLA plates were laminated in five layers and compression-molded into composite panels. Experiments were conducted on the three BFM-to-PLA ratios (35/65, 45/55, and 50/50). Mechanical properties (tensile and bending properties) and physical properties (thickness swell and water absorption) were tested and compared to the currently commercial sheet molding compound (SMC) from fiber glass. The thermal behavior of the BFM/PLA composites was characterized using dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC). The developed BFM/PLA composite product is a sustainable alternative to existing synthetical fiber-reinforced polymer (FRP) that is biodegradable in landfill at the end of life.

Smith, Lee M. (ORCID:0000000264390357)↗

DOE OSTI2022

Mechanical Behavior of Additively Manufactured Molybdenum and Fabrication of Microtextured Composites

Refractory metals are a class of high-melting-temperature materials suitable for use in extreme environment applications. Interestingly, during additive manufacturing many pure refractory metals exhibit a switch from (001) to (111) build direction fiber preference with increasing surface energy density. Here we exploit this solidification physics to fabricate material with “mesoscale composite” engineered structures consisting of features with contrasting (001) and (111) build direction microtextures. Separately, elevated temperature tensile testing of EBM fabricated material with a randomized distribution of mixed (001)/(111)-fiber grains is shown to exhibit excellent properties. These results are utilized to build a crystal plasticity model for evaluating the local inelastic response of the composite mesoscale structures. Analysis of printed microstructures and microstructure-scale simulations indicate that both macro-scale and localized material behavior may be tailored. This strategy can be potentially used to synthesize materials with optimized performance for high-temperature applications.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Bio‐based glycerol plasticizers for flexible poly(vinyl chloride) blends

Abstract A series of glycerol‐based compounds were investigated for their application as plasticizers for flexible poly(vinyl chloride) (PVC) blends. The effect of plasticizer chemical structure on the performance, migration behavior, and blend morphology were evaluated and compared to blends produced using the commercial plasticizer dioctyl terephthalate (DOTP). Blends containing 40 phr (parts per hundred rubber) of glycerol‐based plasticizer showed a considerable reduction (between 54 to 86°C) in glass transition temperature ( T g ) relative to neat PVC ( T g ~ 80°C). Tensile testing of samples prepared with the glycerol analogs demonstrated higher ductility (elongation at break values of up to 97%) than DOTP (elongation at break value of 75%) at identical plasticizer loadings. The surface morphologies showed excellent incorporation of the glycerol plasticizers functionalized with alkyl chains longer than four carbons in length into the PVC matrix, whereas droplet formation was observed in blends with shorter chain glycerol derivatives. Leaching behavior of the plasticized samples were evaluated into different media and showed that plasticizers comprised of branched, or longer alkyl chains produced 2‐ to 4‐fold lower migration rates compared to those with shorter alkyl chains into polar solutions.

Halloran, Matthew W.↗

DOE OSTI2024

3D printed lignin/polymer composite with enhanced mechanical and anti-thermal-aging performance

Lignin is the most abundant natural aromatic polymer globally but is still underutilized as a renewable material, even with its versatile properties. One approach to using lignin is to incorporate it in polymer composites, but this application is often limited by the poor mechanical performance of the resultant composite due to the poor interfacial adhesion. Following the structure–property relationship, stronger interactions were designed to be enhanced by alternating the functional groups of lignin. Here, this study applied a demethylation method to hardwood lignin (Ori-Lig) to introduce more phenolic hydroxyl groups. Research studies with rheology behavior and molecular simulations demonstrated that an increased phenolic hydroxyl content could improve the adhesion between the modified lignin (OH-Lig) and the polymer matrix at the interface. The tensile performance of the samples from the fused depositional modeling (FDM) 3D printing technique was also improved due to the improved interfacial adhesion. Specifically, by adding 10 wt% of the modified lignin, the tensile strength of the 3D printed samples could reach 46.1 MPa (40.2 MPa of Polyamide 12, PA12), and Young’s Modulus could be improved to 1.73 GPa (1.48 GPa of PA12). OH-Lig also improved anti-aging performance so that the tensile strength of the OH-Lig composite after thermo-aging (100 h at 140 °C) remained ~48MPa. The enhanced mechanical performance with anti-aging properties indicated that the OH-Lig composite may replace PA12 to reduce the use of petrol-based materials. This work showed the method of purposefully designing and modifying lignin structures to fulfill the interaction requirements between lignin and polymer matrix. The as-prepared lignin could be used to prepare functional composites to achieve improved mechanical performance and targeted functions at the same time.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

A constitutive model for elastomers tailored by ionic bonds and entanglements

Over the past decade or two, the concept has emerged of using multiple types of weak interactions simultaneously to enhance the mechanical properties of elastomers. These weak interactions include physical entanglements, hydrogen bonds, metal-coordination bonds, dynamic covalent bonds, and ionic bonds. The combination of entanglements and ionic bonding has been minimally explored and is particularly exciting because of the broad application space for polyelectrolytes. In this work, a constitutive model framework is developed to describe the response of elastomers with both ionic bonds and entanglements. Here we formulate a micromechanical model that couples together chain stretching, ionic bond slipping, and entanglement evolution. The ionic bonds provide toughness by enabling plastic deformation in comparison to covalently crosslinked material and add strength compared to a linear polymer. Evolution of the entanglement density is taken as a key mechanism that can govern stiffness, toughness, and self-recovery in elastomers. The model is used to match bulk polyelectrolytes with different fractions of ionic components under a variety of loading histories. The variations in material parameters are then used to help understand the relative importance of different governing mechanisms in the bulk polymers. We show that the theoretical framework can explain our experimental uniaxial tensile experimental results for polyelectrolytes. This model can help to design better material with high stiffness and toughness. We expect that our model can be extended to explain the mechanical behavior of other polyelectrolytes and other soft materials with a wide range of dynamic bonds.

42 ENGINEERING↗

DOE OSTI2023

Stress and Curvature Effects in Layered 2D Ferroelectric CuInP 2 S 6

Nanoscale ferroelectric 2D materials offer the opportunity to investigate curvature and strain effects on materials functionalities. Among these, CuInP 2 S 6 (CIPS) has attracted tremendous research interest in recent years due to combination of room temperature ferroelectricity, scalability to a few layers thickness, and ferrielectric properties due to coexistence of 2 polar sublattices. Here, we explore the local curvature and strain effect on polarization in CIPS via piezoresponse force microscopy and spectroscopy. To explain the observed behaviors and decouple the curvature and strain effects in 2D CIPS, we introduce the finite element Landau–Ginzburg–Devonshire model, revealing strong changes in hysteresis characteristics in regions subjected to tensile and compressive strain. The piezoresponse force microscopy (PFM) results show that bending induces ferrielectric domains in CIPS, and the polarization-voltage hysteresis loops differ in bending and nonbending regions. Furthermore, these studies offer insights into the fabrication of curvature-engineered nanoelectronic devices.

2D materials↗

DOE OSTI2025

Understanding the limitations and potential of micro tensile testing of tungsten and needs for crystal plasticity modelling

Tungsten is the leading plasma facing material candidate due to its exceptional properties. Understanding the response to neutron irradiation is crucial for the lifetime evaluation of tungsten. The limited space in nuclear reactors and the high levels of radioactivity of the specimens after irradiation are significant barriers to accurately measuring the mechanical properties after neutron irradiation. Testing of micro tensile specimens is one approach to reduce the total amount of irradiated material needed for a set of mechanical testing experiments. However, micro samples are not necessarily measuring the bulk material properties, as size effects produce higher measured mechanical properties than is observed in engineering size counterparts. Determining the minimal sample size for reliable bulk property measurement, combined with modeling efforts, is essential. We conducted room temperature tensile tests on tungsten micro tensile specimens fabricated with focused ion beam, plasma focused ion beam and femto-second laser ablation system to dimension of 2×2×7?µm³, 7×7×18?µm³, and 80×100×233?µm³ (width×thickness×gauge-length), respectively. Elevated tensile testing was performed up to 475°C on 5×5×18?µm³ specimens fabricated with focused ion beam. The smallest specimens exhibited a high degree of ductility and strength, whereas the largest specimens demonstrated behavior akin to bulk tungsten. To investigate the effects introduced by the micro specimen fabrication processes and to obtain the necessary bulk dislocation density for the crystal plasticity model, we employed X-ray diffraction depth profiling. This measurement was performed using different X-ray sources with varying penetration depths. Finally, the potential and limitations of micro mechanical tests for tungsten will be discussed.

36 - MATERIALS SCIENCE↗