Search NASA⌕ Search

SEARCH · Search NASA

Results for “texture characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

3D Printed Materials Characterization for Rapid Prototyping and Plant Growth

Through KSC IRTD funding in 2022, this project brought a list of 18, 3D printed filaments into formal characterization testing to provide a reference for their behaviors under relevant applications. The project format set up a series of tests to expose 3D printed specimens. A total of 1,989 individual 3D printed test specimens were sent across KSC to be scrutinized by three laboratories to fulfill a multidisciplinary assessment of each material TRL. Testing started with 18 materials. Initially, seed germination assays in the PPA, sample materials were enclosed in petri dishes with lettuce seeds on damp germination paper. No significant impacts on lettuce seed germination were observed in this testing. Next, sample coupons were printed and sent for materials testing to the KSC Analysis/Mechanical and Environmental Testing Laboratory, where they were subjected to 14- and 30-day soak periods in solutions used to provide nutrients to plants or to sanitize hardware before and after use. Following a long soak typical of a 30-day plant growout in Hoagland’s solution, 14 materials gained more than 10% of their own mass. This indicated an increased potential for leaching or providing conditions that are not food safe. Materials that exceeded 15% absorption by mass were eliminated from further testing. Based off this result, the team continued with a core list of nine filaments to fulfill Tensile, Flexural, Biofilm formation, and plant growth testing. Those materials were PLA (Raise3D), ABS (Raise3D), PETG (PolyethyleneTerephthalate Glycol) (Raise3D), ASA (Acrylonitrile Styrene Acrylate) (Raise3D), PC (Polycarbonate) (Raise3D), TPU (Thermoplastic polyurethane)-95 (Raise3D), PLA Copper (Gizmodorks), PP (Polypropylene) (Braskem), and HIPS (High Impact Polystyrene) (Gizmodorks). Testing also quantified the spectral impact of using different color 3D printed surfaces in a growth chamber. The material used for spectral testing was PLA. Printing employed a standard surface texture representative of all materials. It was shown through Tensile Testing (ASTM D638-22) that the breaking force of a 3D printed part greatly varied depending on layer orientation. This is common through all materials, and demonstrates that the strength of a 3D printed component can be maximized by layering the material normal to the primary force on the part. Four-point flexural testing (ASTM D790) provided quantities of interest, Flexural modulus, Flexural strength, Flexural stress, and strain at break within a 5% strain limit from each of nine materials. Biofilm formation testing was conducted in the Molecular and Microbiological Laboratory. Testing completed on specimens from each material showed equal formation on the surface. Additional plant growth testing was conducted in the PPA beyond the initial germination testing. The final assessment documents that three materials (PLA, ABS, and PC) have reached TRL 6 through extensive testing, and ultimate end-to-end applied use in experimental or testing conditions (flight and ground). TRL 5 materials (ASA, TPU-95, PLA Copper, PP, PETG, and HIPS) have all been successfully applied in Research and Development for crop growth applications and are ready to be applied in formal testing. TRL 4 materials Nylon910, PLA Carbon Fiber, PPA CF, PPA Glass Fiber (GF), NinjaFlex, and P-filament 721 are materials that were able to be printed and tested, but have yet to show data meeting applied requirements. TRL 3 NylonX, Flex TPE-185, and Nylon were unable to be reliably printed to fulfill testing. These results provide researchers with reference for materials to use during plant growth experimentation, and also set a standard for future characterization work applying 3D printing and materials to testing, research, and experimentation.

Gioia Massa↗
NASA NTRS2003

Characterization of Al-Cu-Mg-Ag Alloy RX226-T8 Plate

Aluminum-copper-magnesium-silver (Al-Cu-Mg-Ag) alloys that were developed for thermal stability also offer attractive ambient temperature strength-toughness combinations, and therefore, can be considered for a broad range of airframe structural applications. The current study evaluated Al-Cu-Mg-Ag alloy RX226-T8 in plate gages and compared performance with sheet gage alloys of similar composition. Uniaxial tensile properties, plane strain initiation fracture toughness, and plane stress tearing resistance of RX226-T8 were examined at ambient temperature as a function of orientation and thickness location in the plate. Properties were measured near the surface and at the mid-plane of the plate. Tensile strengths were essentially isotropic, with variations in yield and ultimate tensile strengths of less than 2% as a function of orientation and through-thickness location. However, ductility varied by more than 15% with orientation. Fracture toughness was generally higher at the mid-plane and greater for the L-T orientation, although the differences were small near the surface of the plate. Metallurgical analysis indicated that the microstructure was primarily recrystallized with weak texture and was uniform through the plate with the exception of a fine-grained layer near the surface of the plate. Scanning electron microscope analysis revealed Al-Cu-Mg second phase particles which varied in composition and were primarily located on grain boundaries parallel to the rolling direction. Fractography of toughness specimens for both plate locations and orientations revealed that fracture occurred predominantly by transgranular microvoid coalescence. Introduction High-strength, low-density Al-Cu-Mg-Ag alloys were initially developed to replace conventional 2000 (Al-Cu-Mg) and 7000 (Al-Zn-Cu-Mg) series aluminum alloys for aircraft structural applications [1]. During the High Speed Civil Transport (HSCT) program, improvements in thermal stability were demonstrated for candidate aircraft wing and fuselage skin materials through the addition of silver to Al-Cu-Mg alloys based on Al 2519 chemistry [2]. Thermal stability of the resulting Al-Cu-Mg-Ag alloys, C415-T8 and C416-T8, was due to co-precipitation of the thermally stable . (AlCu) and ' (Al2Cu) strengthening phases [1-4]. The strength and toughness behavior was investigated for these alloys produced as 0.090-inch thick rolled sheet in the T8 condition and after various thermal exposures. The mechanical properties were shown to be competitive with conventional aircraft alloys, 2519-T8 and 2618-T8 [2]. During the Integral Airframe Structure (IAS) program, advanced aluminum alloys were examined for use in an integrally stiffened airframe structure where the skin and stiffeners would be machined from plate and extruded frames would be mechanically attached (see Figure 1) [5]. Advantages of integrally stiffened structure include reduced part count, and reduced assembly times compared to conventional built-up airframe structure. The near-surface properties of a thick plate are of significance for a machined integrally stiffened airframe structure since this represents the skin location. Properties measured at the mid-plane of the plate are more representative of the stiffener web. RX226 was developed to exploit strength-toughness improvements and thermal stability benefits of Al-Cu-Mg-Ag alloys in plate gages. This study evaluated the microstructure and properties of three gages of plate produced in the T8 condition.

Lach, Cynthia L.↗
NASA NTRS2000

Geology of the Smythii and Marginis Region of the Moon: Using Integrated Remotely Sensed Data

We characterized the diverse and complex geology of the eastern limb region of the Moon using a trio of remote-sensing data sets: Clementine, Lunar Prospector, and Apollo. On the basis of Clementine-derived iron and titanium maps we classify the highlands into low-iron (3-6 wt % FeO) and high-iron (6-9 wt % FeO) units. The association of the latter with basalt deposits west of Smythii basin suggests that the highland chemical variation is the result of mixing between basalt and highland lithologies. Mare Smythii and Mare Marginis soils are compositionally similar, containing moderate iron (15-18 wt % FeO) and titanium (2.5-3.5 wt % TiO2). Smythii basin, in addition to the basalt deposits, contains an older, moderate-albedo plains unit. Our investigation reveals that the dark basin plains unit has a distinct albedo, chemistry, and surface texture and formed as a result of impact-mixing between highland and mare lithologies in approximately equal proportions. Clementine iron and maturity maps show that swirls along the northern margin of Mare Marginis have the same iron composition as the surrounding nonswirl material and indicate that the swirl material is bright because of its low agglutinate content. Gravity data for the eastern limb show high, positive Bouguer gravity anomalies for areas of thin basalt cover (e.g., Smythii basin and complex craters Joliot, Lomonosov, and Neper). We deduce that the uplift of dense mantle material is the primary (and mare basaltic fill the secondary) source for generating the concentration of mass beneath large craters and basins.

Gillis, Jeffrey J.↗
NASA NTRS2015

Examining Volcanic Terrains Using In Situ Geochemical Technologies; Implications for Planetary Field Geology

Regardless of the target destination for the next manned planetary mission, the crew will require technology with which to select samples for return to Earth. The six Apollo lunar surface missions crews had only the tools to enable them to physically pick samples up off the surface or from a boulder and store those samples for return to the Lunar Module and eventually to Earth. Sample characterization was dependent upon visual inspection and relied upon their extensive geology training. In the four decades since Apollo however, great advances have been made in traditionally laboratory-based instrument technologies that enable miniaturization to a field-portable configuration. The implications of these advancements extend past traditional terrestrial field geology and into planetary surface exploration. With tools that will allow for real-time geochemical analysis, an astronaut can better develop a series of working hypotheses that are testable during surface science operations. One such technology is x-ray fluorescence (XRF). Traditionally used in a laboratory configuration, these instruments have now been developed and marketed commercially in a field-portable mode. We examine this technology in the context of geologic sample analysis and discuss current and future plans for instrument deployment. We also discuss the development of the Chromatic Mineral Identification and Surface Texture (CMIST) instrument at the NASA Goddard Space Flight Center (GSFC). Testing is taking place in conjunction with the RIS4E (Remote, In Situ, and Synchrotron Studies for Science and Exploration) SSERVI (Solar System Exploration and Research Virtual Institute) team activities, including field testing at Kilauea Volcano, HI..

Young, K. E.↗
NASA NTRSDate not supplied

A Transmission Electron Microscopy Study of a Refractory Metal Grain from a Calcium-Aluminum-Rich Inclusion in the Leoville CV3 Chondrite

Introduction: Calcium-aluminum-rich inclusions (CAIs) are an important component of chondritic meteorites. They can contain materials that are thermodynamically predicted and isotopically age dated to be among the first-formed solids in our solar system [1-5]. Observed in some CAIs are micron to sub-micron sized inclusions rich in Fe, Ni, and high-Z elements such as Pt, Os, Ir and W, in the form of refractory metal nuggets (RMNs), fremdlinges, and ‘nugget like objects’ (NLOs) [1,6]. Refractory siderophile elements such as Os, Ir and Ru are thermodynamically predicted to condense at temperatures well in excess of the major CAI phases such as melilite, perovskite, spinel and hibonite [2,7-9]. These refractory metal inclusions in CAIs can therefore serve as probes into the thermodynamic landscape of the early solar protoplanetary disk. Here we report on a refractory grain identified in a CAI of the Leoville CV3 chondrite. This work is part of an ongoing effort to gain insight into the thermochemistry of the early solar system through systematic analyses of the structure and chemistry of various components in CAIs [10-13]. Sample and Analytical Techniques: A fluffy type A CAI (Fig. 1A) was identified in a section of the Leoville, CV3 chondrite (Center for Meteorite Studies, Arizona State University collection, #821_C_3) using a JOEL-JXA 8530F electron microprobe at Arizona State University. Backscattered electron (BSE) imaging and energy-dispersive X-ray spectroscopy (EDS) were used to identify refractory metal grains in the CAI using a Thermo Fisher (formerly FEI) Helios NanoLab 660 G3 focused-ion-beam scanning-electron microscope (FIBSEM) located at the Kuiper Materials Imaging and Characterization Facility (KMICF) at the Lunar and Planetary Laboratory, University of Arizona. The FIB is equipped with an EDAX EDS system. We selected one of the larger (micron-sized) refractory metal grains, designated as ‘Spud’ (Fig. 1B) for further analysis. ‘Spud’ was extracted and thinned to electron transparency (<100 nm) using the FIB-SEM located in KMICF, following methods described by [14- 15]. The FIB section was analyzed using a 200 keV Hitachi HF5000 scanning transmission electron microscope (S/TEM) located at KMICF. The HF5000 is equipped with cold-field emission gun, 3rd-order spherical aberration corrector for STEM imaging, and an Oxford Instruments X-Max N 100 TLE energydispersive spectroscopy (EDS) system with dual 100 mm2 windowless silicon-drift detectors (Ω = 2.0 sr). Selected-area electron-diffraction (SAED) patterns were acquired to aid in determination of crystallinity and phase. Results: The mineralogy, texture, and morphology of the CAI are consistent with that of a fluffy type A (FTA) CAI [16]. BSE imaging at high magnifications revealed grains with high contrast, indicative of compositions rich in elements of higher atomic number relative to surrounding material. These high-Z grains have sizes that range from ∼250 nm to 4 µm. EDS analyses confirm that the bright grains are metal-rich inclusions. A minor fraction of the grains are composed of only Fe and Ni, but the majority (∼60%) of the identified inclusions also contained various refractory siderophiles including Os, Ru, Zr, Ir and Mo. EDS analysis on the FIB-SEM of Spud shows that it contains Fe, Ni, Mo and Ru. High-angle annular dark-field (HAAFD) imaging and EDS mapping in the TEM (Fig. 2) show that Spud occurs in melilite (Ca1.9Al1.99Si1.06O7). Spud contains a subhedral to anhedral morphology and is compositionally heterogenous (polyphasic, Fig. 2). Local spatial correlation occurs among Fe, Ni, and Pt, and also among Os, Ru, and Mo. SAED patterns show that the Fe-Ni-Pt, Fe-Os-Mo-Ru and Fe-Pt regions are crystalline. Discussion: CAIs can contain various types of inclusions rich in Fe, Ni and refractory siderophiles such as Os, Ru, W and Pt [1]. RMNs are micron-sized, single phase alloy grains and can contain Os, Ir, Ru and Rh [1,7,17]. NLOs are also micron-sized inclusions, but contain two phases, a refractory metal, and an oxide [6]. Fremdlinge are the largest of such inclusions (tens of microns in size) and are complex aggregates of Fe-Ni alloy, silicates, oxides, and sulfides [1,17]. While the size of Spud matches previous descriptions of RMNs and NLOs, Spud is neither a single-phase alloy like RMNs, nor does it contain one metal phase and one oxide like NLOs. Spud does not match the above described categories of refractory metal inclusions. The presence of refractory siderophiles such as Mo, Os, Ru, and Pt suggests a high-temperature origin. Thermodynamic modelling by [7] indicates condensation temperatures of 1917 K, 1693 K, 1613 K and 1415 K for Os, Mo, Ru and Pt respectively. These models also show that following the initial condensation of a refractory metal, alloying of solutes such as Fe, Ni and W, occurs in levels proportional to their partial pressures in the surrounding gas. Such alloying occurs at temperatures above the condensation temperatures of common CAI phases such as melilite (1529 K), perovskite (1441 K), spinel (197 K) and forsterite (1354 K) [2]. The polyphasic nature of Spud could be the result of such high-temperature alloying, possibly shortly after the condensation of Mo and Ru at 1693 K and 1613 K respectively. That Spud occurs as an inclusion is consistent with it having formed prior to and at temperature above that of its host melilite in this FTA CAI, which is qualitatively consistent with such prior thermodynamic modeling. Further, the polyphasic nature of Spud is similar to refractory grains from a FTA CAI in the Northwest Africa (NWA) 8323, CV3 chondrite [11-13]. These data suggest that such refractory metal grains could have been widespread in the inner and early solar protoplanetary disk and represent some of the earliest formed solids to have condensed. Acknowledgments: Research and instrumentation supported by NASA grants #NNX12AL47G, #NNX15AJ22G and #80NSSC19K0509, and NSF grants #1531243 and #0619599. Fig 2. STEM data on ‘Spud’. HAADF Image (Top) False-color EDS Maps (Bottom) References: [1] MacPherson G. J. (2014) T. of Geochem. Vol I: Met. And Cosmochem. Processes, 139-179. [2] Lodders K. (2003) ApJ, 591, 1220-1247. [3] Ebel D. S. (2006) Met. & the Early S. Sys. II., 253- 277. [4] Amelin Y. (2002) Science, 297, 1678-1683. [5] Connelly J.N. et.al. (2012) Science, 338, 651-655. [6] Schwander D. et al. (2015) GCA, 18, 70-87. [7] Palme H. and Wlotzka F. (1976) EPSL, 33, 45-60. [8] Berg T. et al. (2009) ApJ, 702, 172-176. [9] Liffman K. et al. (2021) Icarus, 221, 89-105. [10] Zega T.J. et al. (2021) PSJ, 2, 115. [11] Ramprasad T. et al. (2020) LPSC LI, Abstract #2472. [12] Ramprasad T. et al. (2021) Microscopy & Microanalysis, S1, 2792-2794. [13] Ramprasad T. et al. (2021) 84th MetSoc, Abstract #6123. [14] Zega T.J. et al. (2007) MAPS, 42, 1373-1386. [15] Ramprasad T. et al. (2022) MAPS, in revision. [16] Grossman L. (1975), GCA, 39, 433-454. [17] El Goresy A. et al. (1978) LPSC IX, Abstract#1100

T. Ramprasad↗
NASA NTRS1984

The Colony meteorite and the possible existence of a new chemical subgroup of CO3 chondrites

The Colony meteorite, found in Oklahoma around 1975, has an unrecrystallized texture and contains heterogeneous olivine and low Ca pyroxene, kamacite with low Ni and Co and high Cr, amoeboid inclusions with low FeO and MnO, and numerous small chondrules with clear pink glass. These characteristics are shared by members of the least metamorphosed subgroup of CO3 chondrites. Colony contains a fine grained matrix that has higher FeO and K2O and lower MgO and Na2O than normal CO3 matrices. Allan Hills A77307 is another unmetamorphosed meteorite that has many petrologic similarities to normal CO chondrites, including matrix abundance, mineral compositions and chondrule size. However, it differs from them in its abundance of magnetite and presence of iron carbides. The olivine and low Ca pyroxene compositional distributions of Colony and A77307 are very similar. The shapes of the thermoluminescence glow curves of Colony and A77307 are very similar, but differ significantly from those of normal CO chondrites. It is suggested that Colony and A77307 represent a distinct chemical subgroup of CO3 chondrites, characterized by low Ni, Co, S, Ca, Mg, Mn and, possibly, high Cd.

Rubin, A. E.↗
NASA NTRS2001

Enhancement of Tropical Land Cover Mapping with Wavelet-Based Fusion and Unsupervised Clustering of SAR and Landsat Image Data

The characterization and the mapping of land cover/land use of forest areas, such as the Central African rainforest, is a very complex task. This complexity is mainly due to the extent of such areas and, as a consequence, to the lack of full and continuous cloud-free coverage of those large regions by one single remote sensing instrument, In order to provide improved vegetation maps of Central Africa and to develop forest monitoring techniques for applications at the local and regional scales, we propose to utilize multi-sensor remote sensing observations coupled with in-situ data. Fusion and clustering of multi-sensor data are the first steps towards the development of such a forest monitoring system. In this paper, we will describe some preliminary experiments involving the fusion of SAR and Landsat image data of the Lope Reserve in Gabon. Similarly to previous fusion studies, our fusion method is wavelet-based. The fusion provides a new image data set which contains more detailed texture features and preserves the large homogeneous regions that are observed by the Thematic Mapper sensor. The fusion step is followed by unsupervised clustering and provides a vegetation map of the area.

LeMoigne, Jacqueline↗
NASA NTRSDate not supplied

Mineralogical Variation of the C1 Lithologies in the Kaidun Meteorite

The Kaidun meteorite is a polymict microbreccia, characterized by the presence of numerous clasts of various chondritic and achondritic materials. Chondritic clasts are C1, C2, CM1, CM2, CV3, EH3-5, EL3, and ordinary chondrite-related materials [1,2]. There is significant evidence that aqueous alteration in the carbonaceous chondrite clasts in Kaidun occurred primarily in their parent bodies prior to accumulation to the Kaidun body. Thus, the observation of highly aqueously altered materials (C1 clasts) can provide quantitative constraints on the geologic history of the asteroidal parent bodies. Additionally, the lack of petrological features complicates the classification of C1 materials, but recent studies of new meteorite falls and Ryugu samples continue to emphasize the diversity of C1 materials [e.g., 3,4]. Considering the unprecedentedly diverse origin of clasts in Kaidun, it is expected to contain unknown C1 materials, including ungrouped C1, which will further increase the diversity of those materials. Therefore, this study aims to systematically understand C1 materials by comparing Kaidun C1 with known C1s such as CI1, CM1 and CR1. Since textural observations and chemical composition analyses of carbonates, sulfides, and phyllosilicates in C1 materials in Kaidun have not yet been adequately performed, this study focuses mainly on such analyses.

K. Ogiya↗
NASA NTRS1990

Requirements for long-life operation of inert gas hollow cathodes: Preliminary report

An experimental investigation was initiated to establish conditioning procedures for reliable hollow cathode operation via the characterization of critical parameters in a representative cathode test facility. From vacuum pumpdown rates, it was found that approximately 1.5 hours were required to achieve pressure levels within 5 percent of the lowest attainable pressure for this facility, depending on the purge conditions. The facility atmosphere was determined by a residual gas analyzer to be composed of primarily air and water vapor. The effects of vacuum pumping and inert gas purging were evaluated. A maximum effective leakage rate of 2.0 x 10(exp -3)sccm was observed and its probable causes were examined. An extended test of a 0.64 cm diameter Mo-Re hollow cathode was successfully completed. This test ran for 504 hours at an emission current of 23.0 amperes and a xenon flow rate of 6.1 sccm. Discharge voltage rose continuously from 15 to 21 volts over the course of the test. The temperature of the cathode body during the test was relatively stable at 1160 C. Post-test examination revealed ion-bombardment texturing of the orifice plate to be the only detectable sign of wear on the hollow cathode.

Verhey, Timothy R.↗
NASA NTRS1990

Requirements for long-life operation of inert gas hollow cathodes - Preliminary results

An experimental investigation was initiated to establish conditioning procedures for reliable hollow cathode operation via the characterization of critical parameters in a representative cathode test facility. From vacuum pumpdown rates, it was found that approximately 1.5 hours were required to achieve pressure levels within 5 percent of the lowest attainable pressure for this facility, depending on the purge conditions. The facility atmosphere was determined by a residual gas analyzer to be composed of primarily air and water vapor. The effects of vacuum pumping and inert gas purging were evaluated. A maximum effective leakage rate of 2.0 x 10 (exp -3) sccm was observed and its probable causes were examined. An extended test of a 0.64 cm diameter Mo-Re hollow cathode was successfully completed. This test ran for 504 hours at an emission current of 23.0 amperes and a xenon flow rate of 6.1 sccm. Discharge voltage rose continuously from 15 to 21 volts over the course of the test. The temperature of the cathode body during the test was relatively stable at 1160 C. Post-test examination revealed ion-bombardment texturing of the orifice plate to be the only detectable sign of wear on the hollow cathode.

Verhey, Timothy R.↗
NASA NTRS1983

Seventh Foray - Whitlockite-rich lithologies, a diopside-bearing troctolitic anorthosite, ferroan anorthosites, and KREEP

Seventeen nonmare samples, most of them pristine, are characterized, and implications of the new data are discussed. Five pristine samples are from Apollo 14, near the center of the KREEP-rich zone in the moon's western hemisphere. Three of them are alkali anorthosites rich in Ca-phosphate (whitlockite), which apparently crystallized from magmas with REE contents roughly 6 x those of high-K KREEP. The alkali anorthosites probably formed from Mg-rich magmas that assimilated large amounts of urKREEP, but some might have formed by metasomatism of ferroan anorthosite by urKREEP. The gabbronorite/norite classification scheme is not well suited to western hemisphere lithologies, probably due mainly to the overriding effects of longitude-petrochemistry correlations. A diopside-bearing Mg-rich lithology indicates that a low degree of melting was not a prerequisite for producing gabbroic (high-Ca pyroxene-rich) Mg-rich magmas, and suggests that some source regions of Mg-rich magmas were relatively Ca-rich. Several pristine KREEP fragments from Apollo 15 station 2 are texturally and compositionally much like other pristine KREEP, and thus reinforce the evidence that KREEP is highly uniform. The pristine anorthosites, on the other hand, demonstrate further that lunar anorthosites are diverse.

Warren, P. H.↗
NASA NTRS2008

Small-Body Extensions for the Satellite Orbit Analysis Program (SOAP)

An extension to the SOAP software allows users to work with tri-axial ellipsoid-based representations of planetary bodies, primarily for working with small, natural satellites, asteroids, and comets. SOAP is a widely used tool for the visualization and analysis of space missions. The small body extension provides the same visualization and analysis constructs for use with small bodies. These constructs allow the user to characterize satellite path and instrument cover information for small bodies in both 3D display and numerical output formats. Tri-axial ellipsoids are geometric shapes the diameters of which are different in each of three principal x, y, and z dimensions. This construct provides a better approximation than using spheres or oblate spheroids (ellipsoids comprising two common equatorial diameters as a distinct polar diameter). However, the tri-axial ellipsoid is considerably more difficult to work with from a modeling perspective. In addition, the SOAP small-body extensions allow the user to actually employ a plate model for highly irregular surfaces. Both tri-axial ellipsoids and plate models can be assigned to coordinate frames, thus allowing for the modeling of arbitrary changes to body orientation. A variety of features have been extended to support tri-axial ellipsoids, including the computation and display of the spacecraft sub-orbital point, ground trace, instrument footprints, and swathes. Displays of 3D instrument volumes can be shown interacting with the ellipsoids. Longitude/latitude grids, contour plots, and texture maps can be displayed on the ellipsoids using a variety of projections. The distance along an arbitrary line of sight can be computed between the spacecraft and the ellipsoid, and the coordinates of that intersection can be plotted as a function of time. The small-body extension supports the same visual and analytical constructs that are supported for spheres and oblate spheroids in SOAP making the implementation of the more complex algorithms largely transparent to the user.

Carnright, Robert↗
NASA NTRS2011

Multi-Scale Hydrometeorological Modeling, Land Data Assimilation and Parameter Estimation with the Land Information System

The Land Information System (LIS; http://lis.gsfc.nasa.gov) is a flexible land surface modeling framework that has been developed with the goal of integrating satellite-and ground-based observational data products and advanced land surface modeling techniques to produce optimal fields of land surface states and fluxes. As such, LIS represents a step towards the next generation land component of an integrated Earth system model. In recognition of LIS object-oriented software design, use and impact in the land surface and hydrometeorological modeling community, the LIS software was selected as a co-winner of NASA?s 2005 Software of the Year award.LIS facilitates the integration of observations from Earth-observing systems and predictions and forecasts from Earth System and Earth science models into the decision-making processes of partnering agency and national organizations. Due to its flexible software design, LIS can serve both as a Problem Solving Environment (PSE) for hydrologic research to enable accurate global water and energy cycle predictions, and as a Decision Support System (DSS) to generate useful information for application areas including disaster management, water resources management, agricultural management, numerical weather prediction, air quality and military mobility assessment. LIS has e volved from two earlier efforts -- North American Land Data Assimilation System (NLDAS) and Global Land Data Assimilation System (GLDAS) that focused primarily on improving numerical weather prediction skills by improving the characterization of the land surface conditions. Both of GLDAS and NLDAS now use specific configurations of the LIS software in their current implementations.In addition, LIS was recently transitioned into operations at the US Air Force Weather Agency (AFWA) to ultimately replace their Agricultural Meteorology (AGRMET) system, and is also used routinely by NOAA's National Centers for Environmental Prediction (NCEP)/Environmental Modeling Center (EMC) for their land data assimilation systems to support weather and climate modeling. LIS not only consolidates the capabilities of these two systems, but also enables a much larger variety of configurations with respect to horizontal spatial resolution, input datasets and choice of land surface model through "plugins". LIS has been coupled to the Weather Research and Forecasting (WRF) model to support studies of land-atmosphere coupling be enabling ensembles of land surface states to be tested against multiple representations of the atmospheric boundary layer. LIS has also been demonstrated for parameter estimation, who showed that the use of sequential remotely sensed soil moisture products can be used to derive soil hydraulic and texture properties given a sufficient dynamic range in the soil moisture retrievals and accurate precipitation inputs.LIS has also recently been demonstrated for multi-model data assimilation using an Ensemble Kalman Filter for sequential assimilation of soil moisture, snow, and temperature.Ongoing work has demonstrated the value of bias correction as part of the filter, and also that of joint calibration and assimilation.Examples and case studies demonstrating the capabilities and impacts of LIS for hydrometeorological modeling, assimilation and parameter estimation will be presented as advancements towards the next generation of integrated observation and modeling systems

Peters-Lidard, Christa D.↗
NASA NTRS2001

Characterization of Surface Features in Detached Grown GeSi Crystals

The growth of detached crystals by the Bridgman technique, in which the growing crystal is not in contact with the crucible wall, has been observed both on earth and in microgravity conditions. At present, the mechanisms contributing to the detachment are not completely understood and until recently detachment has not been reproducibly obtained. It is commonly understood that the main factors that promote the occurrence of detached growth include: high contact angle between the melt and the crucible material, high growth angle, and a pressure difference between the annular gap around the solid below the melt and the volume above the melt along the meniscus. These parameters were varied in Bridgman growth experiments to determine the conditions required to achieve detached growth terrestrially in Ge and GeSi alloys. These experiments are in preparation for experiments on the International Space Station (ISS). The detailed objectives of the flight experiments and a description of the growth methods employed are the subject of another presentation at this Congress. Detached crystals were achieved repeatedly in pyrolytic boron nitride ampoules when a pressure difference was employed. All crystals, except for those grown in fused silica ampoules, were easily removed from their containers; however, this fact alone is not sufficient to infer detached growth. Detachment was verified by comparing profilometer measurements of the radius of the samples with observations of the sample surfaces using optical and electron microscopy. The surfaces of the attached areas of the crystals had the same shape and surface texture as the interior crucible wall. Regions of detached growth contained many unique features and crystal facets could usually be observed. Several of these surface features have been correlated with mechanisms of detachment or free surface growth in general and others to processing events or conditions. These results will be compared with observations of surface features on detached regions of microgravity grown crystals.

Cobb, S. D.↗
NASA NTRS2002

Characterization of Surface Features in Detached Grown GeSi Crystals

The growth of detached crystals by the Bridgman technique, in which the growing crystal is not in contact with the crucible wall, has been observed both on earth and in microgravity conditions. At present, the mechanisms contributing to the detachment are not completely understood and until recently detachment has not been reproducibly obtained. It is commonly understood that the main factors that promote the occurrence of detached growth include: high contact angle between the melt and the crucible material, high growth angle, and a pressure difference between the annular gap around the solid below the melt and the volume above the melt along the meniscus. These parameters were varied in Bridgman growth experiments to determine the conditions required to achieve detached growth terrestrially in Ge and GeSi alloys. These experiments are in preparation for experiments on the International Space Station (ISS). The detailed objectives of the flight experiments and a description of the growth methods employed are the subject of another presentation at this Conference. Detached crystals were achieved repeatedly in pyrolytic boron nitride ampoules when a pressure difference was employed. All crystals, except for those grown in fused silica ampoules, were easily removed from their containers, however, this fact alone is not sufficient to infer detached growth. Detachment was verified by comparing profilometer measurements of the radius of the samples with observations of the sample surfaces using optical and electron microscopy. The surfaces of the attached areas of the crystals had the same shape and surface texture as the interior crucible wall. Regions of detached growth contained many unique features and crystal facets could usually be observed. Several of these surface features have been correlated with mechanisms of detachment or free-surface growth and others to processing events or conditions.

Cobb, S. D.↗
NASA NTRS1997

NASA-UVA Light Aerospace Alloy and Structures Technology Program (LA2ST)

This report documents the progress achieved over the past 6 to 12 months on four graduate student projects conducted within the NASA-UVA Light Aerospace Alloy and Structures Technology Program. These studies were aimed specifically at light metallic alloy issues relevant to the High Speed Civil Transport. Research on Hydrogen-Enhanced Fracture of High-Strength Titanium Alloy Sheet refined successfully the high resolution R-curve method necessary to characterize initiation and growth fracture toughnesses. For solution treated and aged Low Cost Beta without hydrogen precharging, fracture is by ductile transgranular processes at 25 C, but standardized initiation toughnesses are somewhat low and crack extension is resolved at still lower K-levels. This fracture resistance is degraded substantially, by between 700 and 1000 wppm of dissolved hydrogen, and a fracture mode change is affected. The surface oxide on P-titanium alloys hinders hydrogen uptake and complicates the electrochemical introduction of low hydrogen concentrations that are critical to applications of these alloys. Ti-15-3 sheet was obtained for study during the next reporting period. Research on Mechanisms of deformation and Fracture in High-Strength Titanium Alloys is examining the microstructure and fatigue resistance of very thin sheet. Aging experiments on 0. 14 mm thick (0.0055 inch) foil show microstructural agility that may be used to enhance fatigue performance. Fatigue testing of Ti-15-3 sheet has begun. The effects of various thermo-mechanical processing regimens on mechanical properties will be examined and deformation modes identified. Research on the Effect of Texture and Precipitates on Mechanical Property Anisotropy of Al-Cu-Mg-X and Al-Cu alloys demonstrated that models predict a minor influence of stress-induced alignment of Phi, caused by the application of a tensile stress during aging, on the yield stress anisotropy of both modified AA2519 and a model Al-Cu binary alloy. This project is no longer included in the NASA-UVA LAST program. Research on the Creep Behavior and Microstructural stability of Al-Cu-Mg-Ag and Al-Cu-Li-Mg-Ag showed that the creep resistance of three candidate aluminum alloys (C415, C416 and ML377) was much superior compared to that of the current Concorde alloy, AA2618. Creep induced change in precipitates at grain boundaries was observed in the alloy which exhibits the highest creep strain of the three examined. The other two alloys developed no detectable microstructural changes at grain boundaries under the creep conditions tested.

Gangloff, Richard P.↗
NASA NTRSDate not supplied

Spaceborne Passive-Microwave and Visible/IR Observations of Severe Weather: Leveraging Multiple Perspectives for Detection, Validation, and Climatologies

Severe weather phenomena not only are responsible for damages to property, infrastructure, and agriculture, they are also difficult to measure in-situ and have been associated with large errors and uncertainties in precipitation estimation that pose challenges to establishing the current climatology of severe storms and their future trend in a changing Earth system. Severe convection exhibits distinct signatures in remote-sensing datasets, where it is manifested as textured or overshooting cloud tops in visible/IR imagery, or resulting a prominent brightness temperature depression in passive-microwave imagery. These distinct deep convective signatures in spaceborne datasets have been leveraged to analyze severe thunderstorms, create climatologies, improve prediction, and provide a method of detection around the globe where traditional ground-based data may be inconsistent or unavailable. Visible/IR and passive-microwave instruments are powerful tools for detecting severe thunderstorms, however, these datasets exhibit key limitations when examined individually: passive-microwave channels have large footprint and exhibit non-uniform beam filling. The visible/IR instruments have fine horizontal resolution but are limited by their insensitivity to processes occurring below cloud top. We investigate the nearly simultaneous and colocated MODIS (visible/IR) and AMSR-E (passive-microwave) onboard the Aqua satellite to leverage both datasets together and assess the extent to which these datasets can be combined to improve severe thunderstorm detection. We pair passive microwave, IR, and visible signatures of severe convection with ground-based weather radar, severe weather reports, and environmental parameters defined by the MERRA-2 reanalysis to characterize potentially severe convective storms observed by Aqua MODIS and AMSR-E. We will discuss how MODIS and AMSR-E signatures may be used together to diagnose storm properties and processes, and how the interrelationships between the signatures varies seasonally and geographically.

Sarah D. Bang↗
NASA NTRSDate not supplied

Zircon, Baddeleyite, and Reidite Found in Ries Crater Suevite

Introduction: Impact events can generate superheated impact melts and even vapor [1]. In the past decade, evidence of the high temperatures and high pressures of the impact process has been found in the impact melt from terrestrial craters (e.g., Mistastin Lake [2], Meteor Crater [3]) and even on the Moon [4–5]. Often, these studies involve zircon or zirconium-bearing phases. Zircon is a particularly useful mineral, due to its robustness and durability against weathering. It is used principally for chronology, but it has a multitude of geologic applications, including geothermometry and fingerprinting magma sources. Here we focus on its capability of recording impact conditions. Grains of zircon (ZrSiO4) are converted at high temperature and/or pressure during an impact event to reidite (a high-pressure polymorph of ZrSiO4) or to tetragonal-ZrO2 + SiO2 [6]. Reidite and tertragonal-ZrO2 leave identifying relicts in the rocks, markers of the high pressures and/or temperatures these rocks underwent. Ries Crater is a 26-km-diameter peak ring crater in southern Germany that formed approximately 15 Ma [7–9]. Ries is the type locality of the polymict impact breccia known as suevite. Here, we report a microanalytical study of suevite from the Ries impact structure. These analyses are used to inform our understanding of the pressure and temperature conditions involved in creating a polymict impact breccia such as suevite in a peak ring crater. Sample Description: The sample, denoted 16RS08, originates from Otting Quarry, at 48.8777° N, 10.7921° E, approximately 17 km from the center of the Ries Crater in Germany (approximately 4 km outside the crater rim). The material recorded in sample 16RS08 is therefore considered an outer suevite. The outer suevite is a discontinuous layer of polymict impact breccia that occurs outside the central ring of Ries, up to 22 km from the center of the crater [9]. Lithic clasts in the outer suevite consist primarily of crystalline basement rocks (gneiss, granite, amphibolite), with less than 5% of lithic clasts being overlying sedimentary rocks (limestone, sandstone, shale) [9]. The thin section studied contains variably shocked lithic and mineral clasts, impact glass, and interstitial minerals that make up the matrix of the breccia (Fig. 1) [9]. Methods: We used a Cameca SX100 electron probe microanalyzer (EPMA) located in the Kuiper Materials Imaging and Characterization Facility (KMICF) at the University of Arizona to obtain 15 elemental X-ray maps of 16RS08. We next used the JEOL 7900F SEM at the Astromaterials Research & Exploration Science (ARES) at NASA Johnson Space Center (JSC) to obtain electron backscatter diffraction (EBSD) maps and energy dispersive X-ray spectroscopy (EDS) maps of select portions of the section. The EBSD data were collected under beam conditions of 20 kV, and ~9 μA, with step sizes varying from 0.05 to 2 μm. Following EBSD data collection, we processed the data using AZtecCrystal and MTEX, a free MATLAB toolbox. Results: We used the elemental X-ray maps to identify the areas of interest in the section, particularly phosphates and Zr-bearing grains. These areas of interest were then targeted for follow up EBSD and EDS analyses. We have identified, through combined EBSD and EDS analysis, the presence of zircon, reidite, and monoclinic-ZrO2 (baddeleyite) in 16RS08. In 16RS08, we have found singular grains of zircon, zircon with a vermicular baddeleyite halo (Fig. 2a), and granular zircon with reidite (Fig. 2b). The different Zr-rich phases and their corresponding textures signifies that this sample underwent a broad spectrum of pressure and temperature conditions during the impact event. For example, zircons surrounded by a vermicular baddeleyite and SiO2 intergrowth (i.e., Fig. 2a) have been shown to preserve evidence of the extremely high temperatures of impact melt, upwards of 2370 °C [2, 6]. Similarly, reidite and granular zircon (i.e., Fig. 2b) have been shown to preserve evidence of high pressure, as the transition to reidite occurs >30 GPa [3, 6]. Future Work: Next, we will process the EBSD and EDS data for these Zr-rich grains, specifically looking for indicators of cubic- or tetragonal-ZrO2 in the baddeleyite remnants and of shock-precursors to the reidite. To further inform our work, we will also obtain BSE images of these grains using a Hitachi S-4800 SEM in KMICF at the University of Arizona, as well as geochemical spot analyses via EPMA. The data collected will be used to constrain the formation conditions of the Ries Crater outer suevite. Acknowledgments: We thank Ken Domanik and Jerry Chang for their support with data collection. This work was supported by a University of Arizona RII Core Facilities Pilot Program grant and start-up funds to JJB. TME thanks A. Cavosie and N. Timms for assistance during field sampling. We acknowledge support from NASA’s Planetary Science Research program for analysis performed at JSC. References: [1] Melosh H. J. (1989) Oxf. U. Press. [2] Timms et al. (2017) EPSL 477, 52–58. [3] Cavosie et al. (2016) Geology 44:9, 703–706. [4] White et al. (2020) Nature Astr. 4, 974–978. [5] Crow C. A. et al. (2017) GCA 202, 264–284. [6] Timms et al. (2017) Earth-Sci. Rev. 165, 185–202. [7] Schmieder M. et al. (2018) GCA 220, 146–157. [8] Schwarz W. H. et al. (2020) M&PS 55:2, 312–325. [9] Stöffler et al. (2013) M&PS 43:4, 515–589.

Zircon↗