Search NASA⌕ Search

SEARCH · Search NASA

Results for “thermal oxide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Tuning Fabrication Factors for Reduced Graphene Oxide Forward Osmosis Membranes

Forward osmosis (FO) may serve as a near-zero energy approach for wastewater management and selective chemical enrichment with an appropriate FO membrane. There is a need for novel FO membranes with better physical stability, chemical compatibility, and enhanced reverse flux selectivity. In this work, we have systematically studied a variety of factors for fabricating thermally reduced graphene oxide (RGO) FO filtration membranes and have demonstrated that with a comparable water flux, the RGO membranes have an exceptionally large reverse flux selectivity with 1.5 M sodium sulfate draw solution, about 7 times larger than that of cellulose triacetate membranes under the same testing condition. The interlayer spacing of the membranes can be fine-tuned by varying temperatures, so that the free interlayer spacing is less than 0.7 nm after exposure to water. The RGO-based membranes offer a few advantages with high reverse flux selectivity, mechanical robustness with strong adhesion to nylong support membranes without damage after FO tests and tape peel tests, and enhanced chromate and chlorine resistance. Finally, we have further demonstrated that in the FO processes, one can concentrate waste brine while simultaneously harvesting the osmotic energy as electricity, offering potential applications of forward osmosis-based osmotic batteries for powering electronic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

FWP FEAA149: “Next Generation Environmental Barrier Coatings”

Environmental barrier coatings (EBCs) are required coatings for utilization of SiC/SiC ceramic matrix composite (CMC) components in gas turbines, where the EBC represents the life-limiting factor for such components. EBC/CMC systems have shown success in aero-engine applications with increased turbine inlet temperatures and improved efficiencies, which are achieved through higher temperature stability, lower density, and decreased reliance on cooling air compared to traditional superalloys. While industrial gas turbines (IGTs) do not currently utilize SiC/SiC CMCs, the current shift towards low-carbon or carbon-free fuel sources for power generation could result in a need for EBC/CMC components with higher temperature capabilities. In this work, three tasks were outlined to improve understanding of EBC lifetimes to encourage use in IGTs with carbon-free fuel such as hydrogen: 1. Define the bond coating oxidation kinetics and EBC failure criteria, 2. Measure thermal expansion coefficients of each layered material, and 3. Perform advanced characterization and modeling to assess EBC lifetimes. Cyclic steam oxidation tests were conducted on various EBC/Si/SiC chemistries and EBC/SiC architectures to define substrate oxidation kinetics and EBC failure modes. An open-source code was developed to quantify the undulating thermally grown oxide thickness with thousands of measurements from specimen cross-section images. Bond coating oxidation kinetics were determined and used to develop a kinetic and thermodynamic model for predicting EBC lifetimes. High-temperature Raman spectroscopy was utilized for determining the SiO 2 thermally grown oxide phase transformation as the life-limiting feature for EBCs. Model efforts supported the claim that the SiO 2 phase transformation causes elevated stress during thermal cycling with associated cracking that decreases the adhesion strength of the EBC, eventually resulting in coating spallation. The finite element model subroutine will be made publicly available upon internal review. Further development of an EBC lifetime model for IGTs involves definition of a critical SiO 2 thickness for EBC spallation and must also consider both environmental (gas velocity, pressure, etc.) and specimen (EBC dopants, layer architectures, etc.) effects into predicted bond coating oxidation kinetics for long-lifetime components.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Initial Developments in Modeling Graphite Behavior

Graphite is used in High Temperature Reactor designs as a moderator, reflector and core material responsible for protecting the fuel and maintaining structural stability. From a safety perspective, it is imperative to be able to predict how graphite will behave under reactor operating conditions which may compromise the core’s structural integrity or fuel’s safety performance. The following report summarizes recent modeling work undertaken at Idaho National Laboratory which focuses on graphite degradation behavior. One phenomenon which is explored in this report and can cause significant degradation to graphite properties is oxidation. Oxidation behavior in graphite is highly temperature dependent. At low temperatures, oxygen can fully penetrate a component and cause a homogeneous damage profile. At high temperatures, only the graphite near the surface of a component is affected. Understanding and modeling this temperature dependence is essential to predicting graphite behavior. In this report, three graphite models are discussed. The first model is used to investigate strength loss after low temperature oxidation. It does this by generating an approximate graphite microstructure then determining the required load to cause crack propagation. It has been shown that the model reproduces the quasi brittle stress versus strain relationship observed in graphite. Strength loss results from the model are shown to match experimental values. The second model investigates strength loss under high temperature oxidation conditions. This model is more applicable to full scale graphite components where the oxidation damage is often inhomogeneous throughout a component. The third model computes stresses in graphite under reactor conditions. Specifically, the model incorporates the effect of creep, irradiation dose, thermal strains, and oxidation in order to predict internal stresses in a component. All of these models are implemented in the Multiphysics Object-Oriented Simulation Environment (MOOSE), an open source, parallel finite element framework.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Laser-Induced Thermal Decomposition of Uranium Coordination Compounds with Non-oxidic Ligands to Produce Nitride and Carbide Materials

The production of ceramics from uranium coordination compounds can be achieved through thermal processing if an excess amount of the desired atoms (i.e., C or N), or reactive gaseous products (e.g., methane or nitrogen oxide) is made available to the reactive uranium metal core via decomposition/fragmentation of the surrounding ligand groups. Here, computational thermodynamic approaches were utilized to identify the temperatures necessary to produce uranium metal from some starting compounds—UI 4 (TMEDA) 2 , UCl 4 (TMEDA) 2 , UCl 3 (pyridine) x , and UI 3 (pyridine) 4 . Experimentally, precursors were irradiated by a laser under various gaseous environments (argon, nitrogen, and methane) creating extreme reaction conditions (i.e., fast heating, high temperature profile >2000 °C, and rapid cooling). Despite the fast dynamics associated with laser irradiation, the central uranium atom reacted with the thermal decomposition products of the ligands yielding uranium ceramics. Residual gas analysis identified vaporized products from the laser irradiation, and the final ceramic products were characterized by powder X-ray diffraction. The composition of the uranium precursor as well as the gaseous environment had a direct impact on the production of the final phases.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

In Situ High-Temperature Synchrotron Diffraction Studies of (Fe,Cr,Al) 3 O 4 Spinels

The modeling of a loss-of-coolant-accident scenario involving nuclear fuels with FeCrAl cladding materials in consideration to replace a Zircaloy requires knowledge of the thermodynamics of oxidized structures. At temperatures higher than 1500 degrees C, oxidation of FeCrAl alloys forms (Fe,Cr,Al) 3 O 4 spinels. In situ high-energy X-ray diffraction in a conical nozzle levitator installed at beamline 6-ID-D of the APS was used to study the structural evolution of the oxides as a function of the temperature. Single-phase (spinel) and multiphase (spinel-corundum-FeAlO 3 ) regions are mapped as a function of the temperature for three different compositions of FeCrAl oxidation products. The thermal expansion coefficients and cation distribution in the spinel structure have been refined. The temperature at which complete melting of the fuel cladding is expected has been determined by the liquidus temperatures of the oxidized products to be between 1657 and 1834 degrees C in a 20% O 2 /Ar atmosphere using the cooling trace method. The liquidus temperature increases with increasing Al and Cr content in the spinel phase.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Reduction kinetics of hercynite redox materials for solar thermochemical water splitting

Solar thermochemical water splitting (STWS) using a hercynite redox cycle is a promising technology for producing renewable H 2 . Here, the reduction kinetics of hercynite (FeAl 2 O 4 ) is evaluated using thermogravimetric and XRD analyses. The results indicate that as-prepared hercynite materials undergo reduction via two different reaction mechanisms. The reaction first proceeds by a nucleation and growth mechanism (AE1), followed by a third-order kinetic model (F3). XRD analyses show the occurrence of superstoichiometric oxygen in the spinel structure of FeAl 2 O 4+δ in the second reaction mechanism, which indicates the formation of cationic vacancies. TGA and XRD analyses confirm that hercynite maintains its spinel structure when the materials are thermally reduced and oxidized with steam. Differential scanning calorimetry (DSC) performed on FeAl 2 O 4 particles shows two heats of reaction in agreement with the two observed mechanisms. This is the first kinetics study to report on the thermal reduction of hercynite.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Thermal aging effects on crosslinked polyethylene cable insulation with decabromodiphenyl ether flame retardant alternative

Decabromodiphenyl ether (decaBDE) has been extensively used as a flame retardant in several applications, including nuclear electrical cable insulation. However, decaBDE has been identified as a persistent, bioaccumulative and toxic (PBT) substance, leading to regulatory scrutiny. The Environmental Protection Agency (EPA) published a regulation on January 6, 2021, aimed at phasing out the manufacturing, processing, and distribution of decaBDE. This rule set a compliance deadline of March 8, 2021, for the manufacture and processing of decaBDE, and an extended deadline of January 6, 2023, for specific applications including wire and cable insulation in nuclear power generation facilities. In response to such regulations, RSCC, a major supplier of safety-related electrical cables and associated products to the U.S. nuclear industry updated the formula of their crosslinked polyethylene (XLPE) insulation to replace the historically used decaBDE flame retardant with an acceptable alternative. This change from the previous decaBDE-containing XLPE prompted interest in comparative performance of the two material formulations, especially with respect to characteristics relevant to safety-related function such as thermal and radiation resistance. RSCC graciously provided samples of wire insulated with the decaBDE-containing XLPE formulation and corresponding wire insulated with XLPE of the new formulation, containing a decaBDE alternative. In this work we compare characteristics of the two formulations and a previously produced commercial version of the RSCC decaBDE-containing XLPE insulation subjected to thermal aging at 150 °C and 165 °C. The comparison was focused on mechanical durability, thermal stability in the oxidative environment, and chemical structures. Briefly, • Tensile elongation at break (EAB) results showed loss of mechanical elasticity with longer aging time, as expected. Aging time dependence of EAB did not differ between the decaBDE-containing and decaBDE-alternative samples. • Subtle differences between the two materials can be detected from Fourier-transform infrared spectroscopy (FTIR) absorbance spectra in the range below 1700 cm -1 , are assumed to be related to decomposition of flame retardant additives during thermal aging. • The oxidation induction time (OIT) data seemed to show that the unaged decaBDE-containing XLPE material is more thermally stable than the unaged decaBDE-alternative material, but the discrepancy in OIT decreased with aging time and the OIT values of the two materials became similar starting with the 4 th day of aging at 165 °C. This thermal aging investigation confirmed that the mechanical durability, a key property monitored for cable qualification, was not significantly affected by the modification of the formulation with a decaBDE alternative flame-retardant system in the investigated thermal aging conditions. Further studies on the same sets of materials exposed to thermal and gamma radiation aging would further inform comparison of the materials safety-related function.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Aluminum-doped U 3 Si 2 composite fuels with enhanced oxidation resistance

Al-doped U 3 Si 2 composite fuels with controlled microstructure were fabricated by spark plasma sintering that display greatly-improved oxidation resistance as compared with monolithic and Al-doped silicides prepared by standard powder metallurgy or arc melting. The effects of Al additives on the thermal-mechanical properties and oxidation resisance of the micron- and nano-sized U 3 Si 2 composites were investigated. Additionally, a minimal addition of 1.8 at% Al is effective to increase the onset oxidation temperature of as-fabricated U 3 Si 2 pellets to 580 °C, which can be further increased to 610 °C by thermal annealing. The Al-doped U 3 Si 2 composite fuels also display simultaneously higher hardness and fracture toughness than un-doped U3Si2. These results highlight an effective strategy by integrating minimal Al additives, microstructure control and post-thermal annealing to design advanced silicide fuels with excellent oxidation resistance, desired thermal-mechanical properties and maintained high fissile element density.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Pathways of Photocatalytic Oxidation of Formic Acid on Dry and Hydrated Anatase TiO 2 Surfaces

The photocatalytic oxidation of formic acid (FA), which is one of the most abundant volatile organic compounds, is a promising air remediation technology inspired by nature. However, the detailed mechanism of this photocatalytic reaction on the surface of TiO 2 , a typical photocatalyst, is not yet well-understood. In this work, we present a computational mechanistic study of the thermal vs photocatalytic oxidation of FA on dry and hydrated anatase TiO 2 (101) surfaces, based on periodic hybrid density functional theory (DFT) calculations, in which the photooxidation is treated as an excited-state process in a constrained triplet spin state. We first compare the adsorption modes of FA on the anatase (101) surface in the ground and excited states, followed by identification of the corresponding reaction intermediates that lead to the formation of CO 2 . We unveil the pivotal role of photogenerated holes localized at surface under-coordinated oxygen sites in mediating the C−H bond cleavage, thereby promoting CO 2 formation through a highly stable intermediate and an exergonic reaction step. Further investigation of the effect of coadsorbed water molecules shows that hydrogen bonding with water stabilizes FA in a monodentate configuration. This is favored over the unreactive bidentate structure that is the most stable under dry conditions, thus providing insight into the experimentally observed increase of the reaction rate in the presence of water.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

MURR LEU structural and thermal hydraulics analyses: Part II – Impacts of irradiation thermo-mechanical behavior on thermal hydraulics safety analyses

A series of structural analyses have been performed to support the conversion of the University of Missouri Research Reactor (MURR) from the use of highly enriched uranium (HEU; ≥20 wt% U-235) to low-enriched uranium (LEU; <20 wt% U-235) fuel. The irradiation thermo-mechanical analysis evaluated the effects of fuel swelling, irradiation creep, thermal expansion, as well as thermal resistance from the oxide layer growth for the MURR LEU element in prototypic thermal and irradiation conditions as presented in Part I of this article. Overall, this irradiation thermo-mechanical analysis predicts smaller gap thickness reductions in previously limiting regions, and larger reductions in the middle of the outermost end channels where power density is not typically a maximum. Due to substantial differences between the channel gap reductions assumed for the previous safety analyses and those predicted by the irradiation thermo-mechanical analysis, a need to evaluate their impact on the thermal hydraulics safety analyses arose. This article presents the results from the steady-state safety analysis for normal operation as well as the two most limiting accident scenarios. The calculation models were revised in order to account for the spatial and temporal variation of the channel gap thicknesses. The results show that sufficient safety margins are still maintained for normal operation as well as during the postulated accident transients. This work provides a methodology of incorporating the irradiation thermo-mechanical behavior of plate-type fuel into the thermal hydraulics safety analyses.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2025

Large-scale experimental validation of thermochemical water-splitting oxides discovered by defect graph neural networks

Thermochemical water-splitting (TCH) based on 2-step thermal redox cycles in metal oxides is a promising approach to generating H 2 , but state-of-the-art (SOTA) CeO 2 has several practical limitations, which has motivated continued materials discovery efforts in this field. Here, in this study, we improve upon a SOTA defect graph neural network (dGNN) surrogate model's oxygen vacancy predictions and combine them with materials project phase diagrams to down-select and discover structurally diverse, experimentally known metal oxides whose TCH performance was previously unknown. Amongst twelve candidates selected based on our high-throughput screening and down-selection criteria, we achieved ∼80% accuracy in identifying materials with stable redox cycling and hydrogen production in stagnation flow reactor water-splitting experiments. Closer to 100% accuracy can be achieved if higher-accuracy, hybrid DFT-predicted vacancy formation energies were computed and used in lieu of the most uncertain dGNN-based screening predictions, as they correct false positives to true negatives. Notably, two discovered candidates, Sr 3 PrMn 2 O 8 and Ba 2 Fe 2 O 5 , display hydrogen yields greater than CeO 2 under specific redox conditions. In conclusion, these results demonstrate our ability to computationally predict and experimentally validate promising candidate TCH materials that have the potential to compete with CeO 2 .

08 HYDROGEN↗
DOE OSTI2020

NH 4 OH Looping with Membrane CO 2 Absorber and Distributed Stripper for Enhanced Algae Growth

The University of Kentucky Center for Applied Energy (UK CAER) has devised a unique, integrated CO2 capture and utilization technology. CO2 from coal-fired power generation flue gas is first captured at half the operating cost of a typical aqueous CO2 capture system (CCS), distributed in an aqueous stream and then fixed by algae in bioreactors where the algae production is increased by 50% over that with a typical intermittent nutrient feeding system. Lower CCS operating cost is achieved by eliminating the flue gas pretreatment step for cooling and SO2 removal, eliminating steam extraction from the power generation steam cycle for solvent regeneration, and eliminating CO2 compression. Higher algae production is achieved by continuous, just-in-time nutrient feed to the bioreactors directly from a distributed solvent regenerator, which maintains the bioreactor pH for optimum growth. The process starts with a uniquely configured membrane absorber, where the flue gas is indirectly contacted with an ammonium hydroxide (NH4OH) solvent. Dissolved NH3 is attractive for both CO2 capture and as an algae nutrient. For CO2 capture it is inexpensive, has a low regeneration energy, is thermally- and oxidatively-stable and has a viscosity near that of water, which makes is easy to transport. Numerous studies have shown that the scrubbing capacity of NH3 is approximately 0.9-1.2 kg of CO2/kg of NH3, with a CO2 removal efficiency of ~99% and half the solvent regeneration energy than that of 30 wt% MEA[1, 2, 3]. NH3 is attractive as an algae nutrient due to its low cost. The rich NH4OH solvent is pumped to a set of distributed regenerators which are co-located with the algae bioreactors. Solvent pumping, transport and distribution reduces the balance of plant (BOP) cost compared to a typical aqueous CCS related to the flue gas duct and boost fan required to transport the flue gas. The energy required for the distributed solvent regeneration is supplied by solar-thermal panels eliminating the need for steam extraction from the power generation steam cycle. After solvent regeneration, the product stream contains both the CO2 captured from the flue gas and volatized NH3 from the solvent. This product stream is fed directly to the bioreactors, eliminating the need for compression of the CO2 stream. The relative amounts of CO2 and NH3 in the product stream are adjusted and controlled by a controlling the regeneration conditions (pressure and temperature). The continuous feed of the right ratio of nutrients overcomes the typical inhibition of algae growth resulting from frequent pH swings in the bioreactor due to unbalanced (intermittent) feeding systems for CO2 and N. Also, because the regenerators will operate at pressure and be located in close proximity to the bioreactors, there is no worry about pressure drop when sparging the gas into the algae. Sparging produces small bubbles which is beneficial for mass transfer efficiency. One known challenge when using an NH4OH solvent is high NH3 emission. Hydrophobic membranes are used for CO2 capture using an aqueous NH3 solution[4, 5] without the direct contact between flue gas and aqueous solution. Additionally, UK CAER CO2 capture and utilization process manages NH3 slip in three extra measures. First, NH3 slip is minimized by working with minimal species partial pressure, which is proportional to the concentration in the liquid. Hence, lowering the capture solvent concentration will lower the NH3 partial pressure. Second, UK CAER’s previous work has demonstrated that the addition of Zn2+ into NH3 solutions to chelate the NH3 can reduce NH3 volatility. Third, the configuration of the membrane CO2 absorber utilizes condensed water from the flue gas to continually wash the gas-side of the membrane to reduce fouling and recapture NH3 slip. Additional details about the UK CAER unique, integrated CO2 capture and utilization technology will be presented along with technology development plans. Diao, N., Q. Li, and Z. Fang. 2004. Heat transfer in ground heat exchangers with groundwater advection. International Journal of Thermal Sciences. 43: 1203-1211, He, Q., M. Chen, L. Meng, K. Liu, and W. Pan. 2004. Study on Carbon Dioxide Removal from Flue Gas by Absorption of Aqueous Ammonia. Western Kentucky University. Yeh, A.C., and H. Bai. 1999. Comparison of ammonia and monoethanolamine solvents to reduce CO2 greenhouse gas emissions. The Science of the Total Environment. 228: 121-133, Villeneuve, K., D. Roizard, J.C. Remigy, M. Iacono, and S. Rode. 2018. CO2 capture by aqueous ammonia with hollow fiber membrane contactors: Gas phase reactions and performance stability. Separation and Purification Technology, 199: 189-197, Toro Molina, C., and C. Bouallou. 2016. Carbon dioxide absorption by ammonia intensified with membrane contactors. Clean Techn Environ Policy 18, 2133–2146 (2016)

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2026

Assessment of multi-stage telescopic control rods in a pebble bed reactor. Part II: corrosion and wear performance

To support High-Temperature Gas-Cooled Reactor designs, the effects of corrosion and wear on a SS316L telescopic control rod prototype were investigated in helium at 775 °C with up to 5 ppm oxygen for durations up to 500 h. Three deployment conditions were tested to assess their impact on wear and oxide formation: severe cycles, daily cycles, and gravity-driven deployments. Here, a chromium-rich oxide layer developed on regions exposed to the helium flow, reaching up to 2 µm in the most affected areas. No carburization or decarburization was observed. Oxide breakthrough occurred mainly at grooves and contact points during severe cycling of the telescopic rod, while in the other tests it was limited to contact points. Friction forces increased due to oxide growth and thermal expansion, the latter being the dominant factor, but never enough to hinder rod deployment significantly. Coaxial misalignment of stages was identified as the main potential risk to reliable operation under normal conditions.

Control rod↗
DOE OSTI2021

Direct Optical Lithography of Colloidal Metal Oxide Nanomaterials for Diffractive Optical Elements with 2π Phase Control

Spatially patterned dielectric materials are ubiquitous in electronic, photonic, and optoelectronic devices. These patterns are typically made by subtractive or additive approaches utilizing vapor-phase reagents. On the other hand, recent advances in solution-phase synthesis of oxide nanomaterials have unlocked a materials library with greater compositional, microstructural, and interfacial tunability. However, methods to pattern and integrate these nanomaterials in real-world devices are less established. In this work, we directly optically pattern oxide nanoparticles (NPs) by mixing them with photosensitive diazo-2-naphthol-4-sulfonic acid and irradiating with widely available 405 nm light. We demonstrate the direct optical lithography of ZrO 2 , TiO 2 , HfO 2 , and ITO NPs and investigate the chemical and physical changes responsible for this photoinduced decrease in solubility. Micron-thick layers of amorphous ZrO 2 NPs were patterned with micron resolution and shown to allow 2 pi phase control of visible light. We also show multilayer patterning and use it to fabricate features with different thicknesses and distinct structural colors. Upon annealing at 400 degrees C, the deposited ZrO 2 structures have excellent optical transparency across a wide wavelength range (0.3-10 mu m), a high refractive index (n = 1.84 at 633 nm), and are optically smooth. We then fabricate diffractive optical elements, such as binary phase diffraction gratings, that show efficient diffractive behavior and good thermal stability. Different oxide NPs can also be mixed prior to patterning, providing a high level of material tunability. This work demonstrates a general patterning approach that harnesses the processability and diversity of colloidal oxide nanomaterials for use in photonic applications.

2𝜋 phase shift↗
DOE OSTI2023

Investigating the Electronic Structure of Prospective Water-Splitting Oxide BaCe 0.25 Mn 0.75 O 3-δ before and after Thermal Reduction

BaCe 0.25 Mn 0.75 O 3-δ (BCM), a non-stoichiometric oxide with a layered perovskite-like crystal structure, has recently emerged as a prospective contender for application in renewable energy harvesting by solar thermochemical hydrogen generation. Using solar-thermal energy and a reducing environment, oxygen vacancies can be created in high-temperature BCM, and the reduced crystal so obtained can, in turn, produce H 2 by stripping oxygen from H 2 O. Therefore, a first step toward understanding the working mechanism and optimizing the performance of BCM is a thorough and comparative analysis of the electronic structure of the pristine and the reduced material. In this paper, we probe the electronic structure of BCM using the combined effort of first-principles calculations and experimental O K-edge X-ray absorption spectroscopy (XAS). The computed projected density of states (PDOS) and orbital plots are used to propose a simplified model for orbital mixing between the oxygen and metal atoms. With the help of state-of-the-art simulations, we are able to find the origins of the XAS peaks and categorize them on the basis of contribution from Ce and Mn. For the reduced crystal, the calculations show that the change in electron density resulting from the reduction is strongly localized around the oxygen vacancy. Experimental measurements reveal a marked lowering of the first O K-edge peak in the reduced crystal. Using theoretical analysis, this is shown to result from lifting of spin degeneracy in the absorption peaks as well as from a diminished O 2p contribution to the frontier unoccupied orbitals, in accordance with the tight binding scheme. The simulated results serve as a reference for the extent of spectral change as a function of the percentage of oxygen vacancies in the reduced crystal. Here, our study paves the way for the investigation of the working mechanism of BCM and for computational and experimental efforts aimed at design and discovery of efficient water-splitting oxides.

08 HYDROGEN↗