Search NASA⌕ Search

SEARCH · Search NASA

Results for “thermodynamic equilibrium”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

Ortho-para-hydrogen equilibration on Jupiter

Voyager IRIS observations reveal that the Jovian para-hydrogen fraction is not in thermodynamic equilibrium near the NH3 cloud top, implying that a vertical gradient exists between the high-temperature equilibrium value of 0.25 at depth and the cloud top values. The height-dependent para-hydrogen profile is obtained using an anisotropic multiple-scattering radiative transfer model. A vertical correlation is found to exist between the location of the para-hydrogen gradient and the NH3 cloud, strongly suggesting that paramagnetic conversion on NH3 cloud particle surfaces is the dominant equilibration mechanism. Below the NH3 cloud layer, the para fraction is constant with depth and equal to the high-temperature equilibrium value of 0.25. The degree of cloud-top equilibration appears to depend on the optical depth of the NH3 cloud layer. Belt-zone variations in the para-hydrogen profile seem to be due to differences in the strength of the vertical mixing.

Carlson, Barbara E.↗

Experimental study and improved modeling of high-temperature air radiation

Spectral emission measurements were conducted in an atmospheric pressure air plasma. The thermodynamic state of the plasma was determined to be close to local thermodynamic equilibrium (LTE), and the temperature profile was measured. The spectrum emitted by the plasma over the range 2,000 to 8,000 A was recorded and calibrated. This spectrum comprises the major radiating molecular bands and atomic lines in air, and is therefore proposed as a benchmark to test radiative calculations. A comparison of these results with the predictions of the NEQAIR code induced several modeling improvements in the code. In particular, radiative transition probabilities and spectroscopic constants were updated, and additional band systems of NO (NO Delta, Epsilon, Beta prime and Gamma prime) were included. Since the C state from which the NO Delta transition originates is predissociated, a simplified collision-predissociation model for this state was added to the code. These changes are presented, and their effect discussed.

Laux, Christophe O.↗

Comparing the results of an analytical model of the no-vent fill process with no-vent fill test results for a 4.96 cu m (175 cu ft) tank

NASA-Lewis has been investigating a no-vent fill method for refilling cryogenic storage tanks in low gravity. Analytical modeling based on analyzing the heat transfer of a droplet has successfully represented the process in 0.034 and 0.142 sq m commercial dewars using liquid nitrogen and hydrogen. Recently a large tank (4.96 sq m) was tested with hydrogen. This lightweight tank is representative of spacecraft construction. This paper presents efforts to model the large tank test data. The droplet heat transfer model is found to overpredict the tank pressure level when compared to the large tank data. A new model based on equilibrium thermodynamics has been formulated. This new model is compared to the published large scale tank's test results as well as some additional test runs with the same equipment. The results are shown to match the test results within the measurement uncertainty of the test data except for the initial transient wall cooldown where it is conservative (i.e., overpredicts the initial pressure spike found in this time frame).

Taylor, William J.↗

Numerical Modeling of a Vortex Stabilized Arcjet

Arcjet thrusters are being actively considered for use in Earth orbit maneuvering applications. Experimental studies are currently the chief means of determining an optimal thruster configuration. Earlier numerical studies have failed to include all of the effects found in typical arcjets including complex geometries, viscosity, and swirling flow. Arcjet geometries are large area ratio converging nozzles with centerbodies in the subsonic portion of the nozzle. The nozzle walls serve as the anode while the centerbody functions as the cathode. Viscous effects are important because the Reynolds number, based on the throat radius, is typically less than 1,000. Experimental studies have shown that a swirl or circumferential velocity component stabilizes a constricted arc. This dissertation describes the equations governing flow through a constricted arcjet thruster. An assumption that the flowfield is in local thermodynamic equilibrium leads to a single fluid plasma temperature model. An order of magnitude analysis reveals the governing fluid mechanics equations are uncoupled from the electromagnetic field equations. A numerical method is developed to solve the governing fluid mechanics equations, the Thin Layer Navier-Stokes equations. A coordinate transformation is employed in deriving the governing equations to simplify the application of boundary conditions in complex geometries. An axisymmetric formulation is employed to include the swirl velocity component as well as the axial and radial velocity components. The numerical method is an implicit finite-volume technique and allows for large time steps to reach a converged steady-state solution. The inviscid fluxes are flux-split, and Gauss-Seidel line relaxation is used to accelerate convergence. Converging-diverging nozzles with exit-to-throat area ratios up to 100:1 and annular nozzles were examined. Quantities examined included Mach number and static wall pressure distributions, and oblique shock structures. As the level of swirl and viscosity in the flowfield increased the mass flow rate and thrust decreased. The technique was used to predict the flow through a typical arcjet thruster geometry. Results indicate swirl and viscosity play an important role in the complex geometry of an arcjet.

Pawlas, Gary E.↗

Microgravity combustion of dust suspensions

Unlike the combustion of homogeneous gas mixtures, there are practically no reliable fundamental data (i.e., laminar burning velocity, flammability limits, quenching distance, minimum ignition energy) for the combustion of heterogeneous dust suspensions. Even the equilibrium thermodynamic data such as the constant pressure volume combustion pressure and the constant pressure adiabatic flame temperature are not accurately known for dust mixtures. This is mainly due to the problem of gravity sedimentation. In normal gravity, turbulence, convective flow, electric and acoustic fields are required to maintain a dust in suspension. These external influences have a dominating effect on the combustion processes. Microgravity offers a unique environment where a quiescent dust cloud can in principle be maintained for a sufficiently long duration for almost all combustion experiments (dust suspensions are inherently unstable due to Brownian motion and particle aggregation). Thus, the microgravity duration provided by drop towers, parabolic flights, and the space shuttle, can all be exploited for different kinds of dust combustion experiments. The present paper describes some recent studies on microgravity combustion of dust suspension carried out on the KC-135 and the Caravelle aircraft. The results reported are obtained from three parabolic flight campaigns.

Lee, John H. S.↗

Comparing the results of an analytical model of the no-vent fill process with no-vent fill test results for a 4.96 cubic meters (175 cubic feet) tank

The NASA Lewis Research Center (NASA/LeRC) have been investigating a no-vent fill method for refilling cryogenic storage tanks in low gravity. Analytical modeling based on analyzing the heat transfer of a droplet has successfully represented the process in 0.034 m and 0.142 cubic m commercial dewars using liquid nitrogen and hydrogen. Recently a large tank (4.96 cubic m) was tested with hydrogen. This lightweight tank is representative of spacecraft construction. This paper presents efforts to model the large tank test data. The droplet heat transfer model is found to over predict the tank pressure level when compared to the large tank data. A new model based on equilibrium thermodynamics has been formulated. This new model is compared to the published large scale tank's test results as well as some additional test runs with the same equipment. The results are shown to match the test results within the measurement uncertainty of the test data except for the initial transient wall cooldown where it is conservative (i.e., overpredicts the initial pressure spike found in this time frame).

Taylor, William J.↗

Analysis of the upper atmosphere CO2(nu-2) vibrational temperatures retrieved from ATMOS/Spacelab 3 observations

An analysis of the upper atmospheric (80-116 km) CO2(nu-2) vibrational temperatures retrieved from atmospheric trace molecule spectroscopy (ATMOS) experiment Spacelab 3 spectra by using a nonlocal thermodynamic equilibrium (non-LTE) radiative transfer model is presented. Thermal collisions with atmospheric atomic oxygen keep this vibrational state very close to LTE up to around 100 km. Above this height, the different deviations from LTE retrieved from ATMOS/Spacelab 3 spectra for the Northern and the Southern Hemispheres are explained in terms of this collisional process and in terms of the different kinetic temperature profiles measured at those locations. From these simultaneous observations of the kinetic and CO2(nu-2) vibrational temperatures, a deactivation rate of CO2(nu-2) by O(3P) has been derived which leads to a rate coefficient value between 3 and 6 x 10 exp -12 cu cm/s and favors an independent or negative temperature dependence rate constant for the atmospheric temperature range. Cooling rates induced by the CO2 15-micron fundamental band in the upper mesosphere and lower thermosphere were derived from the simultaneous kinetic temperature, CO2(nu-2) vibrational temperature, and CO2 concentration, as measured by ATMOS/Spacelab 3, and found to be a factor of between 5 and 10 times larger than those generally accepted until very recently.

Lopez-Puertas, M.↗

An upwind, kinetic flux-vector splitting method for flows in chemical and thermal non-equilibrium

We have developed new upwind kinetic difference schemes for flows with non-equilibrium thermodynamics and chemistry. These schemes are derived from the Boltzmann equation with the resulting Euler schemes developed as moments of the discretized Boltzmann scheme with a locally Maxwellian velocity distribution. Splitting the velocity distribution at the Boltzmann level is seen to result in a flux-split Euler scheme and is called Kinetic Flux Vector Splitting (KFVS). Extensions to flows with finite-rate chemistry and vibrational relaxation is accomplished utilizing nonequilibrium kinetic theory. Computational examples are presented comparing KFVS with the schemes of Van Leer and Roe for a quasi-one-dimensional flow through a supersonic diffuser, inviscid flow through two-dimensional inlet, and viscous flow over a cone at zero angle-of-attack. Calculations are also shown for the transonic flow over a bump in a channel and the transonic flow over an NACA 0012 airfoil. The results show that even though the KFVS scheme is a Riemann solver at the kinetic level, its behavior at the Euler level is more similar to the existing flux-vector splitting algorithms than to the flux-difference splitting scheme of Roe.

Eppard, W. M.↗

Analysis and design of an ultrahigh temperature hydrogen-fueled MHD generator

A coupled gas dynamics/radiative heat transfer analysis of partially ionized hydrogen, in local thermodynamic equilibrium, flowing through an ultrahigh temperature (10,000-20,000 K) magnetohydrodynamic (MHD) generator is performed. Gas dynamics are modeled by a set of quasi-one-dimensional, nonlinear differential equations which account for friction, convective and radiative heat transfer, and the interaction between the ionized gas and applied magnetic field. Radiative heat transfer is modeled using nongray, absorbing-emitting 2D and 3D P-1 approximations which permit an arbitrary variation of the spectral absorption coefficient with frequency. Gas dynamics and radiative heat transfer are coupled through the energy equation and through the temperature- and density-dependent absorption coefficient. The resulting nonlinear elliptic problem is solved by iterative methods. Design of such MHD generators as onboard, open-cycle, electric power supplies for a particular advanced airbreathing propulsion concept produced an efficient and compact 128-MWe generator characterized by an extraction ratio of 35.5 percent, a power density of 10,500 MWe/cu m, and a specific (extracted) energy of 324 MJe/kg of hydrogen. The maximum wall heat flux and total wall heat load were 453 MW/sq m and 62 MW, respectively.

Moder, Jeffrey P.↗

Ground testing for the no-vent fill of cryogenic tanks - Results of tests for a 71 cubic foot tank

NASA Lewis Research has been investigating the no-vent till method, since it is a promising approach to transfer liquid while handling the problems of low-g venting. This paper reports the results of a test series for filling a 71 cu ft tank with liquid hydrogen without venting. Twenty two tests were conducted, ten with a bottom orifice as the inlet and 12 with a spray bar. Parameters investigated included inlet saturation pressures of approximately 5, 15, and 25 psia; transfer pressures of 20, 30, and 45 psia; and various starting wall temperatures. Of the tests, only the one run at the highest wall temperature (238 R) failed to fill the tank. Test results are compared to a thermodynamic equilibrium model. Overall model-data agreement was good except for the tendency of the model to overshoot during the initial wall cool-down of the higher starting wall temperature fills.

Chato, David J.↗

Improved fabrication techniques for infrared bolometers

Techniques are described for producing improved infrared bolometers from doped germanium. Ion implantation and sputter metalization have been used to make ohmic electrical contacts to Ge:Ga chips. This method results in a high yield of small monolithic bolometers with very little low-frequency noise. When one of these chips is used as the thermometric element of a composite bolometer, it must be bonded to a dielectric substrate. The thermal resistance of the conventional epoxy bond has been measured and found to be undesirably large. A procedure for soldering the chip to a metalized portion of the substrate is described which reduced this resistance. The contribution of the metal film absorber to the heat capacity of a composite bolometer has been measured. The heat capacity of a NiCr absorber at 1.3 K can dominate the bolometer performance. A Bi absorber has significantly lower heat capacity. A low temperature blackbody calibrator has been built to measure the optical responsivity of bolometers. A composite bolometer system with a throughput of approx. 0.1 sr sq cm was constructed using the new techniques. In negligible background it has an optical NEP of 3.6 10((exp -15) W/sq root of Hz at 1.0 K with a time constant of 20 ms. The noise in this bolometer is white above 2.5 Hz and is somewhat below the value predicted by thermodynamic equilibrium theory. It is in agreement with calculations based on a recent nonequilibrium theory.

Lange, A. E.↗

The Gaseous Explosive Reaction : The Effect of Inert Gases

Attention is called in this report to previous investigations of gaseous explosive reactions carried out under constant volume conditions, where the effect of inert gases on the thermodynamic equilibrium was determined. The advantage of constant pressure methods over those of constant volume as applied to studies of the gaseous explosive reaction is pointed out and the possibility of realizing for this purpose a constant pressure bomb mentioned. The application of constant pressure methods to the study of gaseous explosive reactions, made possible by the use of a constant pressure bomb, led to the discovery of an important kinetic relation connecting the rate of propagation of the zone of explosive reaction within the active gases, with the initial concentrations of those gases: s = K(sub 1)(A)(sup n1)(B)(sup n2)(C)(sup n3)------. By a method analogous to that followed in determining the effect of inert gases on the equilibrium constant K, the present paper records an attempt to determine their kinetic effect upon the expression given above.

Stevens, F W↗

Program Computes Performances Of Scramjets

SRGULL, a scramjet-cycle-analysis computer code, engineer's software tool capable of nose-to-tail simulation of hydrogen-fueled, scramjet engine integrated with air-frame. Simulated flow that of real gas with equilibrium thermodynamic properties. Program facilities initial estimates of performance of scramjet cycle by linking code for two-dimensional forebody, inlet, and nozzle with code for one-dimensional combustor. Five computer codes (SCRAM, SEAGUL, INLET, Program HUD, and GASH) integrated in program to provide capability for analysis of changing flow conditions. Written in FORTRAN 77.

Walton, J. T.↗

The thermodynamic case for a water-rich Mars

The geologic evidence for a water-rich Mars has been reviewed, and it has been concluded that it is consistent with an outgassed inventory of H2O equivalent to global ocean 0.5-1 km deep. The most persuasive support for this conclusion comes from the martian outflow channels, whose distribution, size, and range of ages, suggests that a significant body of ground water was present on Mars throughout much of its geologic history. In this abstract, the thermodynamic implications of the outflow channels are considered. The results of this analysis suggest that if the outflow channels were carved by the discharge of ground water in diffusive and thermodynamic equilibrium with the overlying frozen crust, it implies a minimum planetary inventory of water in excess of 300 m. However, if the global inventory of ground water on Mars at the time of outflow channel formation was as high as the 500 m estimate of other researchers, then the total inventory of water on Mars could well exceed 750 m.

Clifford, Stephen M.↗

Ground testing for the no-vent fill of cryogenic tanks: Results of tests for a 71 cubic foot tank

NASA Lewis Research has been investigating the no-vent fill method, since it is a promising approach to transfer liquid while handling the problems of low-g venting. This paper reports the results of a test series for filling a 71 cu ft tank with liquid hydrogen without venting. 22 tests were conducted, 10 with a bottom orifice as the inlet and 12 with a spray bar. Parameters investigated included inlet saturation pressures of approximately 5, 15, and 25 psia, transfer pressures of 20, 30, and 45 psia, and various starting wall temperatures. Of the tests, only the one run at the highest wall temperature (238 R) failed to fill the tank. Test results are compared to a thermodynamic equilibrium model. Overall model-data agreement was good except for the tendency of the model to overshoot during the initial wall cool down of the higher starting wall temperature fills.

Chato, David J.↗

Effects of physical aging on long-term behavior of composites

The HSCT plane, envisioned to have a lifetime of over 60,000 flight hours and to travel at speeds in excess of Mach 2, is the source of intensive study at NASA. In particular, polymer matrix composites are being strongly considered for use in primary and secondary structures due to their high strength to weight ratio and the options of property tailoring. However, an added difficulty in the use of polymer based materials is that their properties change significantly over time, especially at the elevated temperatures that will be experienced during flight, and prediction of properties based on irregular thermal and mechanical loading is extremely difficult. This study focused on one aspect of long-term polymer composite behavior: physical aging. When a polymer is cooled to below its glass transition temperature, the material is not in thermodynamic equilibrium and the free volume and enthalpy evolve over time to approach their equilibrium values. During this time, the mechanical properties change significantly and this change is termed physical aging. This work begins with a review of the concepts of physical aging on a pure polymer system. The effective time theory, which can be used to predict long term behavior based on short term data, is mathematically formalized. The effects of aging to equilibrium are proven and discussed. The theory developed for polymers is then applied first to a unidirectional composite, then to a general laminate. Comparison to experimental data is excellent. It is shown that the effects of aging on the long-term properties of composites can be counter-intuitive, stressing the importance of the development and use of a predictive theory to analyze structures.

Brinson, L. Catherine↗

Proposed law of nature linking impacts, plume volcanism, and Milankovitch cycles to terrestrial vertebrate mass extinctions via greenhouse-embryo death coupling

A greenhouse-physiological coupling killing mechanism active among mammals, birds, and reptiles has been identified. Operating via environmental thermal effects upon the maternal core-skin blood flow critical to the survival and development of embryos, it reduces the flow of blood to the uterine tract. Today, during hot summers, this phenomena kills embryos on a vast, global scale. Because of sensitivity of many mammals to modern heat, a major modern greenhouse could reduce population numbers on a global scale, and potentially trigger population collapses in the more vulnerable parts of the world. In the geological past, the killing mechanism has likely been triggered into action by greenhouse warming via impact events, plume volcanism, and Earth orbital variations (Milankovitch cycles). Earth's biosphere is maintained and molded by the flow of energy from the solar energy source to Earth and on to the space energy sink (SES). This SES energy flow maintains Earth's biosphere and its living components, as open, intermediate, dissipative, nonequilibrium systems whose states are dependent upon the rate of energy flowing through them. Greenhouse gases such as CO2 in the atmosphere influence the SES energy flow rate. Steady-state flow is necessary for global ecological stability (autopoiesis). Natural fluctuations of the C cycle such as rapid releases of CO2 from the mantle, or oceans, disrupt steady-state SES flow. These fluctuations constantly challenge the biosphere; slowdown of SES energy flow drives it toward thermodynamical equilibrium and stagnation. Fluctuations induced by impact event, mantle plume volcanism, and Milankovitch cycles can grow into structure-breaking waves triggering major perturbations of Earth's C cycle and mass extinctions. A major C cycle perturbation involves readjustment of the outer physiochemical spheres of the Earth: the atmosphere, hydrosphere, and lithosphere; and by necessity, the biosphere. A greenhouse, one manifestation of a major C cycle perturbation, is the most dangerous natural phenomenon that life on Earth can experience. Greenhouse conditions existed during the KT mass extinctions of 65 m.y. ago, and the Pleistocene-Holocene (P-H) mammalian extinctions of 10,000-12,000 yr ago. Coupling climatology to reproductive physiology via effects of ambient air temperature upon uterine blood flow to developing embryos accounts for the extinctions via established physiological principles.

Mclean, D. M.↗

Explosions of infalling comets in Jupiter's atmosphere

In view of the expected collision of comet Shoemaker-Levy 9 (1993e) with Jupiter in 1994 July, we calculate basic properties of the initial interaction for a simplified Jovian atmosphere. The comet is expected to impact Jupiter at 60 km/sec and at an angle of 45 deg to the zenith. The shock wave generated by the bolide should be optically thick once it has penetrated to an atmospheric density approximately 10(exp -6) gr/cm(exp 3), and we calculate the post-shock conditions assuming local thermodynamic equilibrium (LTE) for shock velocities v(sub sh) in the range 10 to 60 km/sec and preshock densities rho(sub a) = 10(exp -6) to 10(exp -2) gr/cm(exp 3). Our shock calculations include molecular hydrogen, atomic hydrogen, ionized hydrogen, neutral helium, and singly ionized helium. Even at the highest shock velocity, the gas is only partially ionized and the postshock temperature rises with preshock density in order to maintain the ionization. The value of the effective shock adiabatic index gamma(sub sh) varies from 1.17 (at low v(sub sh) and rho(sub a) to 1.40 (at high v(sub sh) and rho(sub a). The ablation rate is limited by the radiative flux that reaches the bolide surface. We argue that the ablated gas does not efficiently transfer its kinetic energy to the atmosphere, and it ultimately slows in a similar fashion to the comet material. As the bolide initially falls through the atmosphere, the character of the shock emission changes. At rho(sub a) approximately 10(exp -8) gr/cm (exp 3), the gas is optically thin and we expect line emission; in the optical spectrum, Balmer emission is expected from the shocked atmosphere and low-ionization metal lines from ablated cometary material. At rho(sub a) approximately 10(exp -6) gr/m(exp 3), the shocked gas is optically thick and the shock front near the bolide produces a blackbody spectrum. The temperature is favorable for ultraviolet (1000 to 3000 A) emission and the luminosity may be approximately 5 x 10(exp 23) ergs/sec for approximately 0.6 sec for a bolide 1 km in radius. At rho(sub a) approximately 10(exp -4) gr/cm(exp 3), the bolide has passed below the ultraviolet photosphere. The shock front emits considerable ionizing radiation, but it is absorbed in a narrow preshock region. The bolometric correction for the optical luminosity is large and we expect a 3000 to 8000 A luminosity of approximately 3 x 10(exp 23) ergs/sec for approximately 1 sec. The optical emission is strongly peaked in the vicinity of the bolide. The bolide does have a somewhat less luminous, optically thick trail extending greater than or equal to 10 km, but the radiation is characterized by a temperature of 4000 to 5000 K. From the fragmentation model of Chyba, Thomas, & Zahnle (1993), the bolide deposits most of its kinetic energy at rho(sub a) approximately 10(exp -3) gr/cm(exp 3) and this is the effective explosion site. The shock wave from such an explosion can move up about one density scale height. We examine the breakout of the shock front from the Jovian atmosphere and find that the shock acceleration in the decreasing density region is slow, so that the energy flux in the shock front is small. Higher velocities might be generated by shock acceleration along the channel left by the bolide if the shock motion can occur before the channel closes off as a result of radiative cooling. Hot gas created by the explosion ultimately rises due to buoyancy on a timescale of a minute. The luminosity is highest when the bubble first rises into the optically thin part of the atmosphere and may be approximately 1 x 10(exp 25) ergs/sec in the near-infrared. Roughly 1% of the initial bolide energy may be radiated in this way; the rest of the energy is lost to sound waves from the initial explosion and to work done by the bubble on the surrounding atmosphere.

Chevalier, Roger A.↗