Search NASA⌕ Search

SEARCH · Search NASA

Results for “turbofan”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Measurements and predictions of flyover and static noise of an afterburning turbofan engine in an F-111 airplane

The noise of the TF30 afterburning turbofan engine in an F-111 airplane was determined from static (ground) and flyover tests. Exhaust temperatures and velocity profiles were measured for a range of power settings. Comparisons were made between predicted and measured jet mixing, internal, and shock noise. It was found that the noise produced at static conditions was dominated by jet mixing noise, and was adequately predicted by current methods. The noise produced during flyovers exhibited large contributions from internally generated noise in the forward arc. For flyovers with the engine at nonafterburning power, the internal noise, shock noise, and jet mixing noise were accurately predicted. During flyovers with afterburning power settings, however, additional internal noise believed to be due to the afterburning process was evident; its level was as much as 8 decibels above the nonafterburning internal noise.

Burcham, F. W., Jr.↗
NASA NTRS1979

Effect of flight loads on turbofan engine performance deterioration

A significant percentage of high-bypass-ratio turbofan engine performance deterioration is caused by an increase in operating clearance between fan/compressor and turbine blades and their outer air seals. These increased clearances result from rubs induced by a combination of engine power transients and aircraft flight loads. An analytical technique for predicting the effect of quasi-steady state aircraft flight loads on engine performance deterioration has been developed and is presented. Thrust, aerodynamic and inertia loads are considered. Analytical results are shown and compared to actual engine test experience.

Stakolich, E. G.↗
NASA NTRS1979

Use of a duct-burning turbofan for an earth-to-orbit vehicle booster

The Space Shuttle will soon reduce the cost of transportation to orbit. The resulting traffic growth will lead to economic pressure for a new vehicle. Several vehicles have been studied. A supersonically staged system with twin turbojet boosters may be attractive but the development of a large supersonic turbojet engine would be required. Subsonic staging with a reasonable number of turbojet engines does not provide the desired payload capability with existing engines. The addition of a duct burner to an existing large turbofan engine provides sufficient thrust to allow the design of an attractive system with twin boosters staged subsonically.

Martin, J. A.↗
NASA NTRS1979

Test verification of a turbofan partial swirl afterburner

Flamespreading velocities exceeding conventional turbulent flamespreading values were demonstrated in a strong centrifugal flow field. This centrifugal flow field flamespreading concept was integrated into an F100 turbofan engine afterburner by introducing swirling airflow into the afterburner. Successful tests were conducted on F100 Engine P072 at sea level and at altitude conditions in a test chamber. This paper summarizes the design approach, engine design verification tests and performance data. Engine tests showed the swirl afterburner increased fuel-air capability improving combustion stability at adverse conditions for combustion in the engine flight envelope. No engine performance or durability degradation was observed.

Hanloser, K. J.↗
NASA NTRS1979

Combined pressure and temperature distortion effects on internal flow of a turbofan engine

The flow characteristics obtained experimentally for the compression of a 2-spool TF30-P-3 turbofan engine operating with 180 grad combined pressure and temperature distortion in the inlet flow are presented. The analytical model (Mazzawy and Banks, 1976), 'tuned' during Lewis testing, was used for pretest predictions of the effects that these distortions would have on the engine flow characteristics and the limiting distortion values. The effect of inlet flow distortion on the performance of the engine is discussed, including: (1) the flow between a screen mounted in the inlet duct and the inlet guide vanes; (2) the flow through the compression system; and (3) the effects of the combined distortion and its orientation on the compressor stability limits. It is concluded that the model used in this program was capable of predicting the effects of total pressure, total temperature and combined total pressure-total temperature distortions in terms of flow profiles, inlet flow angles and attenuation of the distortions through the compressor system. It was also capable of predicting the trends of the limiting values experienced with various orientations of the combined distortions.

Braithwaite, W. M.↗
NASA NTRS1979

Multivariable control altitude demonstration on the F100 turbofan engine

The control system designed under the Multivariable Control Synthesis (MVCS) program for the F100 turbofan engine is described. The MVCS program, applied the linear quadratic regulator (LQR) synthesis methods in the design of a multivariable engine control system to obtain enhanced performance from cross-coupled controls, maximum use of engine variable geometry, and a systematic design procedure that can be applied efficiently to new engine systems. Basic components of the control system, a reference value generator for deriving a desired equilibrium state and an approximate control vector, a transition model to produce compatible reference point trajectories during gross transients, gain schedules for producing feedback terms appropriate to the flight condition, and integral switching logic to produce acceptable steady-state performance without engine operating limit exceedance are described and the details of the F100 implementation presented. The engine altitude test phase of the MVCS program, and engine responses in a variety of test operating points and power transitions are presented.

Lehtinen, B.↗
NASA NTRS1978

A simplified gross thrust computing technique for an afterburning turbofan engine

A simplified gross thrust computing technique extended to the F100-PW-100 afterburning turbofan engine is described. The technique uses measured total and static pressures in the engine tailpipe and ambient static pressure to compute gross thrust. Empirically evaluated calibration factors account for three-dimensional effects, the effects of friction and mass transfer, and the effects of simplifying assumptions for solving the equations. Instrumentation requirements and the sensitivity of computed thrust to transducer errors are presented. NASA altitude facility tests on F100 engines (computed thrust versus measured thrust) are presented, and calibration factors obtained on one engine are shown to be applicable to the second engine by comparing the computed gross thrust. It is concluded that this thrust method is potentially suitable for flight test application and engine maintenance on production engines with a minimum amount of instrumentation.

Hamer, M. J.↗
NASA NTRS1976

Aero-acoustic tests of duct-burning turbofan exhaust nozzles

The acoustic and aerodynamic characteristics of several exhaust systems suitable for duct burning turbofan engines are evaluated. Scale models representing unsuppressed coannular exhaust systems are examined statically under varying exhaust conditions. Ejectors with both hardwall and acoustically treated inserts are investigated.

Kozlowski, H.↗
NASA NTRS1979

Static test-stand performance of the YF-102 turbofan engine with several exhaust configurations for the Quiet Short-Haul Research Aircraft (QSRA)

The performance of a YF-102 turbofan engine was measured in an outdoor test stand with a bellmouth inlet and seven exhaust-system configurations. The configurations consisted of three separate-flow systems of various fan and core nozzle sizes and four confluent-flow systems of various nozzle sizes and shapes. A computer program provided good estimates of the engine performance and of thrust at maximum rating for each exhaust configuration. The internal performance of two different-shaped core nozzles for confluent-flow configurations was determined to be satisfactory. Pressure and temperature surveys were made with a traversing probe in the exhaust-nozzle flow for some confluent-flow configurations. The survey data at the mixing plane, plus the measured flow rates, were used to calculate the static-pressure variation along the exhaust nozzle length. The computed pressures compared well with experimental wall static-pressure data. External-flow surveys were made, for some confluent-flow configurations, with a large fixed rake at various locations in the exhaust plume.

Mcardle, J. G.↗
NASA NTRS1980

Computation of three-dimensional flow in turbofan mixers and comparison with experimental data

A three dimensional, viscous computer code was used to calculate the mixing downstream of a typical turbofan mixer geometry. Experimental data obtained using pressure and temperature rakes at the lobe and nozzle exit stations were used to validate the computer results. The relative importance of turbulence in the mixing phenomenon as compared with the streamwise vorticity set up by the secondary flows was determined. The observations suggest that the generation of streamwise vorticity plays a significant role in determining the temperature distribution at the nozzle exit plane.

Povinelli, L. A.↗
NASA NTRS1980

Core noise investigation of the CF6-50 turbofan engine

Acoustic data obtained during the running of the CF6-50 turbofan engine on an outdoor test stand are presented. The test was conducted to acquire simultaneous internal and far-field measurements to determine the influence of internally generated noise on the far-field measurements. The data includes internal and far-field narrowband and one-third octave band pressure spectra.

Doyle, V. L.↗
NASA NTRS1980

Method and apparatus for rapid thrust increases in a turbofan engine

Upon a landing approach, the normal compressor stator schedule of a fan speed controlled turbofan engine is temporarily varied to substantially close the stators to thereby increase the fuel flow and compressor speed in order to maintain fan speed and thrust. This running of the compressor at an off-design speed substantially reduces the time required to subsequently advance the engine speed to the takeoff thrust level by advancing the throttle and opening the compressor stators.

Cornett, J. E.↗
NASA NTRS1980

Avco Lycoming quiet clean general aviation turbofan engine

A fan module was developed using an existing turboshaft engine. The fan was designed using the latest in large engine noise control technology. A mixer was added to reduce the already low exhaust gas velocity. A nacelle incorporating sound treatment was provided for the test engine. A noise prediction model was used through the design process to evaluate the various design alternatives. Acoustic tests were then made to verify the prediction and identify the noise characteristics of the fan, core, jet, and sound treatment. Analysis of the recorded data yielded close agreement with the expected results. Core noise, as was expected, was the predominant source of noise for the quiet clean general aviation turbofan (QCGAT) engine. Flyover noise predictions were made which indicated that the Avco Lycoming QCGAT engine would meet the goals set for the QCGAT program.

Wilson, C. A.↗
NASA NTRS1979

Analytical study of the effects of wind tunnel turbulence on turbofan rotor noise

The influence of tunnel turbulence on turbofan rotor noise was carried out to evaluate the effectiveness of the NASA Ames 40 by 80 foot tunnel in simulating flight levels of fan noise. A previously developed theory for predicting rotor/turbulence interaction noise was refined and extended to include first-order effects of inlet turbulence anisotropy. This theory was then verified by carrying out extensive data/theory comparisons. The resulting model computer program was then employed to carry out a parametric study of the effects of fan size, blade number, and operating line on rotor/turbulence noise for outdoor test stand. NASA Ames wind tunnel, and flight inlet turbulence conditions. A major result of this study is that although wind tunnel rotor/turbulence noise levels are not as low as flight levels they are substantially lower than the outdoor test stand levels and do not mask other sources of fan noise.

Gliebe, P. R.↗
NASA NTRS1980

Advanced component technologies for energy-efficient turbofan engines

A cooperative government-industry effort, the Energy Efficient Engine Project, to develop the advanced technology base for future commercial development of a new generation of more fuel conservative turbofan engines for airline use is described. Engine configurations that are dependent upon technology advances in each major engine component are defined and current design and development of the advanced components are included.

Saunders, N. T.↗
NASA NTRS1980

Design, evaluation and test of an electronic, multivariable control for the F100 turbofan engine

A digital, multivariable control design procedure for the F100 turbofan engine is described. The controller is based on locally linear synthesis techniques using linear, quadratic regulator design methods. The control structure uses an explicit model reference form with proportional and integral feedback near a nominal trajectory. Modeling issues, design procedures for the control law and the estimation of poorly measured variables are presented.

Skira, C. A.↗
NASA NTRS1980

Influence of pressure driven secondary flows on the behavior of turbofan forced mixers

A finite difference procedure was developed to analyze the three dimensional subsonic turbulent flows in turbofan forced mixer nozzles. The method is based on a decomposition of the velocity field into primary and secondary flow components which are determined by solution of the equations governing primary momentum, secondary vorticity, thermal energy, and continuity. Experimentally, a strong secondary flow pattern was identified which is associated with the radial inflow and outflow characteristics of the core and fan streams and forms a very strong vortex system aligned with the radial interface between the core and fan regions. A procedure was developed to generate a similar generic secondary flow pattern in terms of two constants representing the average radial outflow or inflow in the core and fan streams as a percentage of the local streamwise velocity. This description of the initial secondary flow gave excellent agreement with experimental data. By identifying the nature of large scale secondary flow structure and associating it with characteristic mixer nozzle behavior, it is felt that the cause and effect relationship between lobe design and nozzle performance can be understood.

Anderson, B.↗
NASA NTRS1980

Investigation of performance deterioration of the CF6/JT9D, high-bypass ratio turbofan engines

The aircraft energy efficiency program within NASA is developing technology required to improve the fuel efficiency of commercial subsonic transport aricraft. One segment of this program includes engine diagnostics which is directed toward determining the sources and causes of performance deterioration in the Pratt and Whitney Aircraft JT9D and General Electric CF6 high-bypass ratio turbofan engines and developing technology for minimizing the performance losses. Results of engine performance deterioration investigations based on historical data, special engine tests, and specific tests to define the influence of flight loads and component clearances on performance are presented. The results of analysis of several damage mechanisms that contribute to performance deterioration such as blade tip rubs, airfoil surface roughness and erosion, and thermal distortion are also included. The significance of these damage mechanisms on component and overall engine performance is discussed.

Ziemianski, J. A.↗