Search NASA⌕ Search

SEARCH · Search NASA

Results for “variable coefficients”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Correlation of Preston-tube data with laminar skin friction (Log No. J12984)

Preston tube data within laminar boundary layers obtained on a sharp ten-degree cone in the NASA Ames eleven-foot transonic wind tunnel are correlated with the corresponding values of theoretical skin friction. Data were obtained over a Mach number range of 0.30 to 0.95 and unit Reynolds numbers of 9.84, 13.1, and 16.4 million per meter. The rms scatter of skin friction coefficient about the correlation is of the order of one percent, which is comparable to the reported accuracy for calibrations of Preston tubes in incompressible pipe flows. In contrast to previous works on Preston tube/skin friction correlations, which are based on the physical height of the probe's face, this satisfactory correlation for compressible boundary layer flows is achieved by accounting for the effects of a variable "effective" height of the probe. The coefficients, which appear in the correlation, are dependent on the particular tunnel environment. The general procedure can be used to define correlations for other wind tunnels.

Reed, T. D.↗
NASA NTRS1987

Analysis of eccentric annular incompressible seals. II - Effects of eccentricity on rotordynamic coefficients

A new analysis procedure has been presented which solves for the flow variables of an annular pressure seal in which the rotor has a large static displacement (eccentricity) from the centered position. The present paper incorporates the solutions to investigate the effect of eccentricity on the rotordynamic coefficients. The analysis begins with a set of governing equations based on a turbulent bulk-flow model and Moody's friction factor equation. Perturbations of the flow variables yields a set of zeroth- and first-order equations. After integration of the zeroth-order equations, the resulting zeroth-order flow variables are used as input in the solution of the first-order equations. Further integration of the first order pressures yields the eccentric rotordynamic coefficients. The results from this procedure compare well with available experimental and theoretical data, with accuracy just as good or slightly better than the predictions based on a finite-element model.

Nelson, C. C.↗
NASA NTRS1982

Correlation of Preston-tube data with laminar skin friction

Preston-tube data have been obtained on a sharp ten-degree cone in the NASA Ames Eleven-Foot Transonic Wind Tunnel. Data were obtained over a Mach number range of 0.30 to 0.95 and unit Reynolds numbers of 9.84, 13.1, and 16.4 million per meter. The portions of these data, that were obtained within laminar boundary layers, have been correlated with the corresponding values of theoretical skin friction. The rms scatter of skin-friction coefficient about the correlation is of the order of one percent, which is comparable to the reported accuracy for calibrations of Preston-tubes in incompressible pipe-flows. In contrast to previous works on Preston-tube/skin-friction correlations, which are based on the physical height of the probe's face, this very satisfactory correlation for compressible boundary-layer flows is achieved by accounting for the effects of a variable 'effective' height of the probe. The coefficients, which appear in the correlation, are dependent on the particular tunnel environment. The general procedure can be used to define correlations for other wind tunnels.

Reed, T. D.↗
NASA NTRS2020

Lot-to-lot Variability of BN Grades for Space Electric Propulsion Applications

Historically, several grades of hot pressed hexagonal boron nitride have been used for space electric propulsion applications. This study investigates the material properties of a selection of commercially available boron nitride grades including HP, M26, M, BNXX, and Shapal Hi-M. This work complements data which was presented at JANNAF 2018. The grades selected for this study are of interest because their available billet size is sufficient for space electric propulsion. This research investigates a range of material properties, tailored and focused on enhancing performance, reliability, and economics of electric propulsion thrusters. This work builds upon previous efforts by studying lot-to-lot variability of some of the properties of interest. Coefficient of friction, moisture absorption, moisture sensitivity, hot press directionality, flexural strength, compression strength, elastic modulus, thermal conductivity, thermal emissivity, thermal expansion, density, X-ray diffraction phase, microstructure, and chemical composition were all investigated across two lots of materials to help guide the selection of advanced ceramics. Variability between lots is the critical concern of the study.

Mackey, Jonathan A.↗
NASA NTRS1986

Circulation-Control Variable-Pitch Propeller

Circulation-control variable-pitch propeller has large lift value at moderate blowing coefficients. Based on circulation-control airfoil concept, has no moving parts other than needed for propeller rotation. Substituted for conventional variable-pitch propeller airfoil, lowers manufacturing costs, reduces maintenance, and improves reliability.

Garner, H. D.↗
NASA NTRS1956

An Engineering Approach to the Variable Fluid Property Problem in Free Convection

An analysis is made for the variable fluid property problem for laminar free convection on an isothermal vertical flat plate. For a number of specific cases, solutions of the boundary layer equations appropriate to the variable property situation were carried out for gases and liquid mercury. Utilizing these findings, a simple and accurate shorthand procedure is presented for calculating free convection heat transfer under variable property conditions. This calculation method is well established in the heat transfer field. It involves the use of results which have been derived for constant property fluids, and of a set of rules (called reference temperatures) for extending these constant property results to variable property situations. For gases, the constant property heat transfer results are generalized to the variable property situation by replacing beta (expansion coefficient) by one over T sub infinity and evaluating the other properties at T sub r equals T sub w minus zero point thirty-eight (T sub w minus T sub infinity). For liquid mercury, the generalization may be accomplished by evaluating all the properties (including beta) at this same T sub r. It is worthwhile noting that for these fluids, the film temperature (with beta equals one over T sub infinity for gases) appears to serve as an adequate reference temperature for most applications. Results are also presented for boundary layer thickness and velocity parameters.

Gregg, J. L.↗
NASA NTRS1977

Analysis of torsional spectra of molecules with two internal C3v rotors. II - Far infrared and low frequency Raman spectra of dimethylether isotopes

The torsional far infrared and Raman spectra of gaseous CH3OCH3, CD3OCH3, and CD3OCD3 are presented. They are analyzed using a computer program which is based on the results of an extensive investigation of the isometric groups and of the symmetry groups of the rotation-internal rotation Hamiltonians of a series of semirigid two-top models. Four or more Fourier coefficients of the potential functions in two variables could be determined for each isotope. Strong evidence was found for Fermi-resonance-type interactions with the COC bending mode.

Groner, P.↗
NASA NTRS1976

An efficient procedure for computing partial ionization of a gas in numerical fluid dynamics

A numerical procedure is described that allows efficient solution for the three nonlinear and implicit equations of state relating the equilibrium properties of a partially (and singly) ionized neutral gas. In the computation, the values for the intensive variables, that is pressure, temperature and ionization coefficient, are iteratively obtained with a given accuracy starting from assigned values for energy and volume per unit mass. Iterative computation is performed only when the value for the ionization coefficient lies within the lower and the upper bounds fixed by the required number of significant digits; otherwise the two explicit equations of state for nonionized or for fully ionized gases are employed.

Garribba, S.↗
NASA NTRS1984

Friction and wear behavior of aluminum and composite airplane skins

Friction and wear behavior was determined for small skin specimens under abrasive loading conditions typical of those occurring on the underside of a transport airplane during emergency belly landing. A test apparatus consisting of a standard belt sander provided the sliding surface. Small test specimens constructed of aluminum, standard graphite-epoxy composite, aramid-epoxy composite, and toughened-resin composites were tested undar a range of pressures, belt velocities, and belt-surface textures. The effects of these test variables on the wear rate and the coefficient of friction are discussed and comparisons are made between the composite materials and aluminum. The effect of fiber orientation in the composite materials on wear rate was also investigated. In addition, tests were performed in which thermocouples were imbedded into the various test specimens to obtain temperature-time histories during abrasion.

Jackson, K. E.↗
NASA NTRS1985

Friction and wear behavior of aluminum and composite I-beam stiffened airplane skins

Friction and wear behavior was determined for I-beam stiffened skins constructed of aluminum, graphite-epoxy composite, and glass hybrid composite under abrasive loading conditions typical of those occurring on the underside of a transport airplane during an emergency belly landing. A test apparatus was developed to abrade the test specimens on actual runway surface under a range of pressures (2-5 psi) and velocities (16-50 mph). These parameters were chosen to fall within the range of conditions typical of an airframe sliding on a runway surface. The effects of the test variables on the wear rate and the coefficient of friction are discussed and comparisons are made between the composite materials and aluminum. In addition, the test apparatus was equipped to monitor the temperature variations on the backside of the skins during abrasion and these results are presented.

Jackson, K. E.↗
NASA NTRS1986

Direct simulation of typical AOTV entry flows

The direct simulation Monte Carlo method is applied to two flows that are relevant to the projected aeroassisted orbital transfer vehicle. The first is the axially symmetric flow about a 70 degree blunted cone shield with a cylindrical afterbody, and the second is the one-dimensional flow along the stagnation streamline of the first flow. The shock standoff distance for the stagnation streamline study is obtained from the full axially symmetric calculation. Advantage is then taken of the speed of the one-dimensional calculation to study the sensitivity of the stagnation point heat transfer to a number of physical variables. These include the chemical reaction rate coefficients, the surface catalycity, the electric field associated with ambipolar diffusion, and the nonequilibrium thermal radiation from the shock front.

Bird, G. A.↗
NASA NTRS1988

Application of a semianalytical technique for sensitivity analysis of unsteady aerodynamic computations

A semianalytical approach is developed for the sensitivity analysis of linear unsteady aerodynamic loads. The semianalytical approach is easier to implement than the analytical approach. It is also computationally less expensive than the finite difference approach when used with panel methods which require a large number of panels. The semianalytical approach is applied to an isolated airfoil in a two-dimensional flow and rotating propfan blades in three-dimensional flow. Sensitivity coefficients with respect to nonshape-dependent variables are shown for some cases.

Murthy, Durbha V.↗
NASA NTRS1993

Experimental partitioning of Zr, Ti, and Nb between silicate liquid and a complex noble metal alloy and the partitioning of Ti between perovskite and platinum metal

El Goresy et al.'s observation of Nb, Zr, and Ta in refractory platinum metal nuggets (RPMN's) from Ca-Al-rich inclusions (CAI's) in the Allende meteorite led them to propose that these lithophile elements alloyed in the metallic state with noble metals in the early solar nebula. However, Grossman pointed out that the thermodynamic stability of Zr in the oxide phase is vastly greater than metallic Zr at estimated solar nebula conditions. Jones and Burnett suggested this discrepancy may be explained by the very non-ideal behavior of some lithophile transition elements in noble metal solutions and/or intermetallic compounds. Subsequently, Fegley and Kornacki used thermodynamic data taken from the literature to predict the stability of several of these intermetallic compounds at estimated solar nebula conditions. Palme and Schmitt and Treiman et al. conducted experiments to quantify the partitioning behavior of certain lithophile elements between silicate liquid and Pt-metal. Although their results were somewhat variable, they did suggest that Zr partition coefficients were too small to explain the observed 'percent' levels in some RPMN's. Palme and Schmitt also observed large partition coefficients for Nb and Ta. No intermetallic phases were identified. Following the work of Treiman et al., Jurewicz and Jones performed experiments to examine Zr, Nb, and Ti partitioning near solar nebula conditions. Their results showed that Zr, Nb, and Ti all have an affinity for the platinum metal, with Nb and Ti having a very strong preference for the metal. The intermetallic phases (Zr,Fe)Pt3, (Nb,Fe)Pt3, and (Ti,Fe)Pt3 were identified. Curiously, although both experiments and calculations indicate that Ti should partition strongly into Pt-metal (possibly as TiPt3), no Ti has ever been observed in any RPMN's. Fegley and Kornacki also noticed this discrepancy and hypothesized that the Ti was stabilized in perovskite which is a common phase in Allende CAI's.

Jurewicz, Stephen R.↗
NASA NTRS1999

Unsteady Aerodynamic Testing Using the Dynamic Plunge Pitch and Roll Model Mount

A final report on the DyPPiR tests that were run are presented. Essentially it consists of two parts, a description of the data reduction techniques and the results. The data reduction techniques include three methods that were considered: 1) signal processing of wind on - wind off data; 2) using wind on data in conjunction with accelerometer measurements; and 3) using a dynamic model of the sting to predict the sting oscillations and determining the aerodynamic inputs using an optimization process. After trying all three, we ended up using method 1, mainly because of its simplicity and our confidence in its accuracy. The results section consists of time history plots of the input variables (angle of attack, roll angle, and/or plunge position) and the corresponding time histories of the output variables, C(sub L), C(sub D), C(sub m), C(sub l), C(sub m), C(sub n). Also included are some phase plots of one or more of the output variable vs. an input variable. Typically of interest are pitch moment coefficient vs. angle of attack for an oscillatory motion where the hysteresis loops can be observed. These plots are useful to determine the "more interesting" cases. Samples of the data as it appears on the disk are presented at the end of the report. The last maneuver, a rolling pull up, is indicative of the unique capabilities of the DyPPiR, allowing combinations of motions to be exercised at the same time.

Lutze, Frederick H.↗
NASA NTRS2000

Demonstration of the Application of Composite Load Spectra (CLS) and Probabilistic Structural Analysis (PSAM) Codes to SSME Heat Exchanger Turnaround Vane

This report describes a probabilistic structural analysis performed to determine the probabilistic structural response under fluctuating random pressure loads for the Space Shuttle Main Engine (SSME) turnaround vane. It uses a newly developed frequency and distance dependent correlation model that has features to model the decay phenomena along the flow and across the flow with the capability to introduce a phase delay. The analytical results are compared using two computer codes SAFER (Spectral Analysis of Finite Element Responses) and NESSUS (Numerical Evaluation of Stochastic Structures Under Stress) and with experimentally observed strain gage data. The computer code NESSUS with an interface to a sub set of Composite Load Spectra (CLS) code is used for the probabilistic analysis. A Fatigue code was used to calculate fatigue damage due to the random pressure excitation. The random variables modeled include engine system primitive variables that influence the operating conditions, convection velocity coefficient, stress concentration factor, structural damping, and thickness of the inner and outer vanes. The need for an appropriate correlation model in addition to magnitude of the PSD is emphasized. The study demonstrates that correlation characteristics even under random pressure loads are capable of causing resonance like effects for some modes. The study identifies the important variables that contribute to structural alternate stress response and drive the fatigue damage for the new design. Since the alternate stress for the new redesign is less than the endurance limit for the material, the damage due high cycle fatigue is negligible.

Rajagopal, Kadambi R.↗
NASA NTRS2000

A Probabilistic Framework for the Validation and Certification of Computer Simulations

The paper presents a methodology for quantifying, propagating, and managing the uncertainty in the data required to initialize computer simulations of complex phenomena. The purpose of the methodology is to permit the quantitative assessment of a certification level to be associated with the predictions from the simulations, as well as the design of a data acquisition strategy to achieve a target level of certification. The value of a methodology that can address the above issues is obvious, specially in light of the trend in the availability of computational resources, as well as the trend in sensor technology. These two trends make it possible to probe physical phenomena both with physical sensors, as well as with complex models, at previously inconceivable levels. With these new abilities arises the need to develop the knowledge to integrate the information from sensors and computer simulations. This is achieved in the present work by tracing both activities back to a level of abstraction that highlights their commonalities, thus allowing them to be manipulated in a mathematically consistent fashion. In particular, the mathematical theory underlying computer simulations has long been associated with partial differential equations and functional analysis concepts such as Hilbert spares and orthogonal projections. By relying on a probabilistic framework for the modeling of data, a Hilbert space framework emerges that permits the modeling of coefficients in the governing equations as random variables, or equivalently, as elements in a Hilbert space. This permits the development of an approximation theory for probabilistic problems that parallels that of deterministic approximation theory. According to this formalism, the solution of the problem is identified by its projection on a basis in the Hilbert space of random variables, as opposed to more traditional techniques where the solution is approximated by its first or second-order statistics. The present representation, in addition to capturing significantly more information than the traditional approach, facilitates the linkage between different interacting stochastic systems as is typically observed in real-life situations.

Ghanem, Roger↗
NASA NTRS2006

Uncertainty Analysis for a Jet Flap Airfoil

An analysis of variance (ANOVA) study was performed to quantify the potential uncertainties of lift and pitching moment coefficient calculations from a computational fluid dynamics code, relative to an experiment, for a jet flap airfoil configuration. Uncertainties due to a number of factors including grid density, angle of attack and jet flap blowing coefficient were examined. The ANOVA software produced a numerical model of the input coefficient data, as functions of the selected factors, to a user-specified order (linear, 2-factor interference, quadratic, or cubic). Residuals between the model and actual data were also produced at each of the input conditions, and uncertainty confidence intervals (in the form of Least Significant Differences or LSD) for experimental, computational, and combined experimental / computational data sets were computed. The LSD bars indicate the smallest resolvable differences in the functional values (lift or pitching moment coefficient) attributable solely to changes in independent variable, given just the input data points from selected data sets. The software also provided a collection of diagnostics which evaluate the suitability of the input data set for use within the ANOVA process, and which examine the behavior of the resultant data, possibly suggesting transformations which should be applied to the data to reduce the LSD. The results illustrate some of the key features of, and results from, the uncertainty analysis studies, including the use of both numerical (continuous) and categorical (discrete) factors, the effects of the number and range of the input data points, and the effects of the number of factors considered simultaneously.

Green, Lawrence L.↗
NASA NTRS2019

Analyzing Machine Learning Predictions of Passive Microwave Brightness Temperature Spectral Difference Over Snow-Covered Terrain in High Mountain Asia

Snow is an important component of the terrestrial freshwater budget in high mountainAsia (HMA) and contributes to the runoff in Himalayan rivers through snowmelt. Despitethe importance of snow in HMA, considerable spatiotemporal uncertainty exists across the different estimates of snow water equivalent for this region. In order to better estimate snow water equivalent, radiative transfer models are often used in conjunction with microwave brightness temperature measurements. In this study, the efficacy of support vector machines (SVMs), a machine learning technique, to predict passive microwave brightness temperature spectral difference (1Tb) as a function of geophysical variables (snow water equivalent, snow depth, snow temperature, and snow density) is explored through a sensitivity analysis. The use of machine learning (as opposed to radiative transfer models) is a relatively new and novel approach for improving snow water equivalent estimates. The Noah-MP land surface model within the NASALand Information System framework is used to simulate the hydrologic cycle over HMA and model geophysical variables that are then used for SVM training. The SVMsserve as a nonlinear map between the geophysical space (modeled in Noah-MP) andthe observation space (1Tb as measured by the radiometer). Advanced MicrowaveScanning Radiometer-Earth Observing System measured passive microwave brightness temperatures over snow-covered locations in the HMA region are used as training data during the SVM training phase. Sensitivity of well-trained SVMs to each Noah-MP modeled state variable is assessed by computing normalized sensitivity coefficients. Sensitivity analysis results generally conform with the known first-order physics. Input states that increase volume scattering of microwave radiation, such as snow density and snow water equivalent, exhibit a plurality of positive normalized sensitivity coefficients. In general, snow temperature was the most sensitive input to the SVM predictions. The sensitivity of each state is location and time dependent. The signs of normalized sensitivity coefficients that indicate physical irrationality are ascribed to significant cross-correlation between Noah-MP simulated states and decreased SVM prediction capability at specific locations due to insufficient training data. SVM prediction pitfalls do exist that serve to highlight the limitations of this particular machine learning algorithm.

high mountain Asia↗