Results for “vertical alignment” — Page 15

NASA NTRS1997

Micro-Mechanical Voltage Tunable Fabry-Perot Filters Formed in (111) Silicon

The MEMS (Micro-Electro-Mechanical-Systems) technology is quickly evolving as a viable means to combine micro-mechanical and micro-optical elements on the same chip. One MEMS technology that has recently gained attention by the research community is the micro-mechanical Fabry-Perot optical filter. A MEMS based Fabry-Perot consists of a vertically integrated structure composed of two mirrors separated by an air gap. Wavelength tuning is achieved by applying a bias between the two mirrors resulting in an attractive electrostatic force which pulls the mirrors closer. In this work, we present a new micro-mechanical Fabry-Perot structure which is simple to fabricate and is integratable with low cost silicon photodetectors and transistors. The structure consists of a movable gold coated oxide cantilever for the top mirror and a stationary Au/Ni plated silicon bottom mirror. The fabrication process is single mask level, self aligned, and requires only one grown or deposited layer. Undercutting of the oxide cantilever is carried out by a combination of RIE and anisotropic KOH etching of the (111) silicon substrate. Metallization of the mirrors is provided by thermal evaporation and electroplating. The optical and electrical characteristics of the fabricated devices were studied and show promissing results. A wavelength shift of 120nm with 53V applied bias was demonstrated by one device geometry using 6.27 micrometer air gap. The finesse of the structure was 2.4. Modulation bandwidths ranging from 91KHz to greater than 920KHz were also observed. Theoretical calculations show that if mirror reflectivity, smoothness, and parallelism are improved, a finesse of 30 is attainable. The predictions also suggest that a reduction of the air gap to 1 micrometer results in an increased wavelength tuning range of 175 nm with a CMOS compatible 4.75V.

Patterson, James D.↗

NASA NTRSDate not supplied

Using DIC for Long Slender Structures

High-strain composite deployable structures have been developed for systems such as solar arrays, camera masts or solar sailing propulsion elements. Composite booms in such applications are often flattened and then rolled into a small footprint for low-packaged volume and are then deployed in space. There is a need to obtain deformation for long, slender composite booms on earth through gravity offloading by suspending them vertically and applying distal end (tip) loads. Three-dimensional digital image correlation (3D-DIC), along with other measurement techniques, were used to obtain strain and displacement along the length of a 7.5 m subscale composite Triangular, Rollable, and Collapsible (TRAC) boom in preparation for full scale testing of a 30 m boom. However, incorporating 3D-DIC as a primary measurement tool on long, slender, high-aspect-ratio boom structures presents significant challenges. Challenges include small correlated area due to high aspect ratio, limited standoff distance due to size of test area, coordinate system alignment of multiple camera systems along the length of the boom, nodal mesh extraction for adequate test/analysis correlation, as well as measurement comparison between DIC and other instrumentation used such as fiber optic strain sensing (FOSS) and laser displacement tracking. The contents of the proposed paper will focus on techniques and methods for overcoming the previously mentioned challenges associated with applying 3D-DIC to long, slender boom structures. Results from subscale test along with lessons learned will be discussed.

Deployable Boom↗

NASA NTRS2017

A Mobile Robot for Locomotion Through a 3D Periodic Lattice Environment

This paper describes a novel class of robots specifically adapted to climb periodic lattices, which we call 'Relative Robots'. These robots use the regularity of the structure to simplify the path planning, align with minimal feedback, and reduce the number of degrees of freedom (DOF) required to locomote. They can perform vital inspection and repair tasks within the structure that larger truss construction robots could not perform without modifying the structure. We detail a specific type of relative robot designed to traverse a cuboctahedral (CubOct) cellular solids lattice, show how the symmetries of the lattice simplify the design, and test these design methodologies with a CubOct relative robot that traverses a 76.2 mm (3 in.) pitch lattice, MOJO (Multi-Objective JOurneying robot). We perform three locomotion tasks with MOJO: vertical climbing, horizontal climbing, and turning, and find that, due to changes in the orientation of the robot relative to the gravity vector, the success rate of vertical and horizontal climbing is significantly different.

Aeronautics↗

NASA NTRS2010

The OTOLITH Experiment - Assessment of Otolith Function During Postflight Re-adaption

The ongoing "Otolith" experiment is designed to comprehensively assess the otolith function during the re-adaptation phase after spaceflight. The novel protocol includes unilateral testing of each of the two otolith organs the utricle and the saccule. To assess utricle function, the otolith-ocular response (OOR) and the subjective visual vertical (SVV) are measured during unilateral centrifugation, which permits independent stimulation of the right and left ear. Measurement of the unilateral otolith-ocular response (uOOR) yields information on the response behaviour of the right and left peripheral utricles, whereas the SVV reflects the behaviour of the entire pathway from the peripheral otolith receptors to the vestibular cortex. Thus, by comparative evaluation of the results from the two tests, the degree of peripheral versus central adaptation during the post-flight period can be determined. To assess unilateral saccule function, vestibular evoked myogenic potentials (VEMP) are recorded. Since the saccules are predominantly aligned to gravity, and interplay with the antigravity muscles, it is hypothesised that these potentials shall be altered after spaceflight. To date the study has been conducted with 5 of a planned 8 short-flight Shuttle astronauts. Preliminary results will be discussed together with those from clinical studies of dizziness patients, where the same test protocol is employed. ACKNOWLEDGEMENT This work is supported by the German Aerospace Center (Grant DLR W130729) and is conducted under the auspices of ESA, in cooperation with NASA.

Clarke, A. H.↗

NASA NTRS1993

Giant radiating dyke swarms on Earth and Venus

On Earth, giant radiating dyke swarms are usually preserved as fan-shaped fragments which have been dismembered from their original configuration by subsequent plate tectonic rifting events. Analysis of the largest fragments and consideration of their original configuration has led to the idea that many swarms are plume related, and that dyke swarms radiate away from plume centers. Magellan radar data reveal abundant intact giant radiating swarms on Venus which are similar in scale and pattern to those on Earth. The absence of intense weathering and plate tectonic processes on Venus accounts for the preservation of the primary radiating patterns. It is characteristic of both Earth and Venus that giant radiating dikes are emplaced laterally for distances of at least 2000 km away from plume centers. At distances beyond the influence of the plume on both Earth and Venus, the radiating dyke pattern is often swept into a linear pattern aligned with the regional stress field. There is tremendous potential synergism between the characterization and analysis of terrestrial dyke swarms (where significant erosion has revealed their structure and emplacement directions at depth) and the giant swarms of Venus (where the complete circumferential structure is preserved, and the surface fracture systems above near surface dikes and the nature of the central source regions are revealed). In this study, we report on the characteristics of radial dyke swarms on Earth and Venus and draw some preliminary comparisons from the two perspectives. In summary, on both planets there is evidence for plume-related magmatic centers associated with vertical and lateral injection of magma over considerable distances (up to at least 2000 km). The abundance of very broadly radiating swarms on Venus supports the notion that the swarms on Earth were radiating over broad sectors at the time of intrusion but were dissected by later events. The Venus data show that a swarm can change from radiating (proximal) to regional (distal) subparallel orientations. An implication for Earth is that many regional linear swarms which do not have a radiating pattern may be due to fragmentation of the swarm during later plate tectonic rifting. Completion of the global classification and census of Venus features, comparison to the terrestrial synthesis, and documentation of the mode of emplacement of dikes in these environments (buffered and unbuffered conditions) should lead to additional general insight into mechanisms of formation and evolution and their relation to plumes.

Ernst, Richard E.↗

NASA NTRS2016

Design and Calibration of a Raman Spectrometer for use in a Laser Spectroscopy Instrument Intended to Analyze Martian Surface and Atmospheric Characteristics for NASA

This project's goal is the design of a Raman spectroscopy instrument to be utilized by NASA in an integrated spectroscopy strategy that will include Laser-Induced Breakdown Spectroscopy (LIBS) and Laser-Induced Florescence Spectroscopy (LIFS) for molecule and element identification on Mars Europa, and various asteroids. The instrument is to be down scaled from a dedicated rover mounted instrument into a compact unit with the same capabilities and accuracy as the larger instrument. The focus for this design is a spectrometer that utilizes Raman spectroscopy. The spectrometer has a calculated range of 218 nm wavelength spectrum with a resolution of 1.23 nm. To filter out the laser source wavelength of 532 nm the spectrometer design utilizes a 532 nm wavelength dichroic mirror and a 532 nm wavelength notch filter. The remaining scatter signal is concentrated by a 20 x microscopic objective through a 25-micron vertical slit into a 5mm diameter, 1cm focal length double concave focusing lens. The light is then diffracted by a 1600 Lines per Millimeter (L/mm) dual holographic transmission grating. This spectrum signal is captured by a 1-inch diameter double convex 3 cm focal length capture lens. An Intensified Charge Couple Device (ICCD) is placed within the initial focal cone of the capture lens and the Raman signal captured is to be analyzed through spectroscopy imaging software. This combination allows for accurate Raman spectroscopy to be achieved. The components for the spectrometer have been bench tested in a series of prototype developments based on theoretical calculations, alignment, and scaling strategies. The mounting platform is 2.5 cm wide by 8.8 cm long by 7 cm height. This platform has been tested and calibrated with various sources such as a neon light source and ruby crystal. This platform is intended to be enclosed in a ruggedized enclosure for mounting on a rover platform. The size and functionality of the Raman spectrometer allows for the rover to carry other mission critical devices. This project will be continued at NASA until the requirements are met for the expected initial 2020 launch date.

Lucas, John F.↗

NASA NTRS2011

Impact of Footprint Diameter and Off-Nadir Pointing on the Precision of Canopy Height Estimates from Spaceborne Lidar

A spaceborne lidar mission could serve multiple scientific purposes including remote sensing of ecosystem structure, carbon storage, terrestrial topography and ice sheet monitoring. The measurement requirements of these different goals will require compromises in sensor design. Footprint diameters that would be larger than optimal for vegetation studies have been proposed. Some spaceborne lidar mission designs include the possibility that a lidar sensor would share a platform with another sensor, which might require off-nadir pointing at angles of up to 16 . To resolve multiple mission goals and sensor requirements, detailed knowledge of the sensitivity of sensor performance to these aspects of mission design is required. This research used a radiative transfer model to investigate the sensitivity of forest height estimates to footprint diameter, off-nadir pointing and their interaction over a range of forest canopy properties. An individual-based forest model was used to simulate stands of mixed conifer forest in the Tahoe National Forest (Northern California, USA) and stands of deciduous forests in the Bartlett Experimental Forest (New Hampshire, USA). Waveforms were simulated for stands generated by a forest succession model using footprint diameters of 20 m to 70 m. Off-nadir angles of 0 to 16 were considered for a 25 m diameter footprint diameter. Footprint diameters in the range of 25 m to 30 m were optimal for estimates of maximum forest height (R(sup 2) of 0.95 and RMSE of 3 m). As expected, the contribution of vegetation height to the vertical extent of the waveform decreased with larger footprints, while the contribution of terrain slope increased. Precision of estimates decreased with an increasing off-nadir pointing angle, but off-nadir pointing had less impact on height estimates in deciduous forests than in coniferous forests. When pointing off-nadir, the decrease in precision was dependent on local incidence angle (the angle between the off-nadir beam and a line normal to the terrain surface) which is dependent on the off-nadir pointing angle, terrain slope, and the difference between the laser pointing azimuth and terrain aspect; the effect was larger when the sensor was aligned with the terrain azimuth but when aspect and azimuth are opposed, there was virtually no effect on R2 or RMSE. A second effect of off-nadir pointing is that the laser beam will intersect individual crowns and the canopy as a whole from a different angle which had a distinct effect on the precision of lidar estimates of height, decreasing R2 and increasing RMSE, although the effect was most pronounced for coniferous crowns.

Pang, Yong↗

NASA NTRS1997

Ultima Replicated Optics Research

Designs are reviewed incorporating processes suitable for replication of precision spherical segments of very large (greater than 20 meter diameter) telescopes combining ultra-lightweight and high precision. These designs must be amenable to assembly and alignment after deployment . The methods considered lie outside the present scope of fabrication, deployment and alignment considered to date. Design guidelines for reducing the weight and low frequency resonance in low G environment were given by The Serius Group, Dr. Glenn Zeiders, and are considered baseline for this activity. The goal of a rigid design of 10 Kg/sq M is being persued for the Next Generation Space Telescope (NGST) and is not likely adequate for advanced efforts. Flexures have been considered for maintaining the figure of many lightweight structures by control loop processes. This adds to the complexity and weight to the extent that it becomes difficult to recover the benefits. Two fabrication guidelines lead to a stiffer and concurrently lighter structure. First the use of thin vertical wall triangular structural reinforcements to increase the resistance to bending is preferred over hexagonal or square similar sections. Secondly, the incorporation of a similar back sheet on a cellular structure markedly improves the geometric stiffness. Neither improves the short range stiffness. Also often overlooked is that selected material properties must include high microyield and low hysteresis in addition to high elastic modulus to weight (stiffness). The fabrication steps can easily exceed the strain requirement.

Hadaway, James↗

NASA NTRS1999

Experimental Investigation of Pool Boiling Heat Transfer Enhancement in Microgravity in the Presence of Electric Fields

In boiling high heat fluxes are possible driven by relatively small temperature differences, which make its use increasingly attractive in aerospace applications. The objective of the research is to develop ways to overcome specific problems associated with boiling in the low gravity environment by substituting the buoyancy force with the electric force to enhance bubble removal from the heated surface. Previous studies indicate that in terrestrial applications nucleate boiling heat transfer can be increased by a factor of 50, as compared to values obtained for the same system without electric fields. The goal of our research is to experimentally explore the mechanisms responsible for EHD heat transfer enhancement in boiling in low gravity conditions, by visualizing the temperature distributions in the vicinity of the heated surface and around the bubble during boiling using real-time holographic interferometry (HI) combined with high-speed cinematography. In the first phase of the project the influence of the electric field on a single bubble is investigated. Pool boiling is simulated by injecting a single bubble through a nozzle into the subcooled liquid or into the thermal boundary layer developed along the flat heater surface. Since the exact location of bubble formation is known, the optical equipment can be aligned and focused accurately, which is an essential requirement for precision measurements of bubble shape, size and deformation, as well as the visualization of temperature fields by HI. The size of the bubble and the frequency of bubble departure can be controlled by suitable selection of nozzle diameter and mass flow rate of vapor. In this approach effects due to the presence of the electric field can be separated from effects caused by the temperature gradients in the thermal boundary layer. The influence of the thermal boundary layer can be investigated after activating the heater at a later stage of the research. For the visualization experiments a test cell was developed. All four vertical walls of the test cell are transparent, and they allow transillumination with laser light for visualization experiments by HI. The bottom electrode is a copper cylinder, which is electrically grounded. The copper block is heated with a resistive heater and it is equipped with 6 thermocouples that provide reference temperatures for the measurements with HI. The top electrode is a mesh electrode. Bubbles are injected with a syringe into the test cell through the bottom electrode. The working fluids presently used in the interferometric visualization experiments, water and PF 5052, satisfy requirements regarding thermophysical, optical and electrical properties. A 30kV power supply equipped with a voltmeter allows to apply the electric field to the electrodes during the experiments. The magnitude of the applied voltage can be adjusted either manually or through the LabVIEW data acquisition and control system connected to a PC. Temperatures of the heated block are recorded using type-T thermocouples, whose output is read by a data acquisition system. Images of the bubbles are recorded with 35mm photographic and 16mm high-speed cameras, scanned and analyzed using various software packages. Visualized temperature fields HI allows the visualization of temperature fields in the vicinity of bubbles during boiling in the form of fringes. Typical visualized temperature distributions around the air bubbles injected into the thermal boundary layer in PF5052 are shown. The temperature of the heated surface is 35 C. The temperature difference for a pair of fringes is approximately 0.05 C. The heat flux applied to the bottom surface is moderate, and the fringe patterns are regular. In the image a bubble penetrating the thermal boundary layer is visible. Because of the axial symmetry of the problem, simplified reconstruction techniques can be applied to recover the temperature field. The thermal plume developing above the heated surface for more intensive heating is shown. The temperature distribution in the liquid is clearly 3D, and tomographic techniques have to be applied to recover the temperature distribution in such a physical situation. A sequence of interferometric images showing the temperature distribution around the rising bubble, recorded with a high-speed camera is shown. Again, the temperature distribution is 3D, and a more complex approach to the evaluation, the tomographic reconstruction has to be taken. Measurement of the temperature distribution from the fringe pattern temperature distributions that yield important information regarding heat transfer are determined. Two algorithms that allow the quantitative evaluation of interferometric fringe patterns and the reconstruction of temperature fields during boiling have been developed at the Heat Transfer Laboratory of the Johns Hopkins University. In the first algorithm the bubble is assumed to be axially symmetrical, which significantly reduces the computational effort for quantifying the temperature distribution around the bubble. For this purpose the thermal boundary layer around the bubble is divided into equidistant concentric shells, and the refractive index is assumed to be constant in each of the shells. Since large temperature gradients are expected in the vicinity of the bubble during boiling, the deflection of the light beam cannot be neglected in boiling experiments. Since the exit angle of the light beam is known, this allows to account for the deflections and phase shifts outside the boundary layer (in the bulk fluid and in the windows of the test cell). Three dimensional temperature distributions in the vicinity of the bubble are reconstructed using tomographic techniques. In tomography, the measurement volume is sliced into 2D planes. In the present study these planes are parallel to the heated surface. The objective is to determine the values of the field parameter of interest in form of the field function in these 2D planes. The field parameter is the change of the refractive index of the liquid in the measurement volume caused by temperature changes. By superimposing data for many 2D planes recorded at the same time instant, the 3D temperature distribution in the measurement volume is recovered.

Herman, Cila↗

NASA NTRS2005

Spray Cooling Trajectory Angle Impact Upon Heat Flux Using a Straight Finned Enhanced Surface

Experiments were conducted to study the effects of spray trajectory angles upon heat flux for flat and enhanced surface spray cooling. The surface enhancement consisted of straight fins machined on the top surface of a copper heater block. Spray cooling curves were obtained with the straight fin surface aligned both parallel (axial) and perpendicular (transverse) to the spray axis. Measurements were also obtained on a flat surface heater block for comparison purposes. Each copper block had a cross-sectional area of 2.0 sq cm. A 2x2 nozzle array was used with PF-5060 as the working fluid. Thermal performance data was obtained under nominally degassed (chamber pressure of 41.4 kPa) conditions. Results show that the maximum CHF in all cases was attained for a trajectory angle of 30' from the surface normal. Furthermore, trajectory angles applied to straight finned surfaces can have a critical heat flux (CHF) enhancement as much as 75% (heat flux value of 140 W/sq cm) relative to the vertical spray orientation for the analogous flat surface case under nominally degassed conditions.

Silk, Eric A.↗

NASA NTRS2003

The Highly Robust Electrical Interconnects and Ultrasensitive Biosensors Based on Embedded Carbon Nanotube Arrays

We report on our recent breakthroughs in two different applications using well-aligned carbon nanotube (CNT) arrays on Si chips, including (1) a novel processing solution for highly robust electrical interconnects in integrated circuit manufacturing, and (2) the development of ultrasensitive electrochemical DNA sensors. Both of them rely on the invention of a bottom-up fabrication scheme which includes six steps, including: (a) lithographic patterning, (b) depositing bottom conducting contacts, (c) depositing metal catalysts, (d) CNT growth by plasma enhanced chemical vapor deposition (PECVD), (e) dielectric gap-filling, and (f) chemical mechanical polishing (CMP). Such processes produce a stable planarized surface with only the open end of CNTs exposed, whch can be further processed or modified for different applications. By depositing patterned top contacts, the CNT can serve as vertical interconnects between the two conducting layers. This method is fundamentally different fiom current damascene processes and avoids problems associated with etching and filling of high aspect ratio holes at nanoscales. In addition, multiwalled CNTs (MWCNTs) are highly robust and can carry a current density of 10(exp 9) A/square centimeters without degradation. It has great potential to help extending the current Si technology. The embedded MWCNT array without the top contact layer can be also used as a nanoelectrode array in electrochemical biosensors. The cell time-constant and sensitivity can be dramatically improved. By functionalizing the tube ends with specific oligonucleotide probes, specific DNA targets can be detected with electrochemical methods down to subattomoles.

Li, Jun↗

NASA NTRSDate not supplied

Assimilation of Active MW and Radar Observations in the NWP Models

Passive instruments lack the ability to provide vertically resolved measurements of clouds and precipitation, which can be obtained by active radar instruments. However, incorporating these active measurements into data assimilation systems presents challenges due to the absence of fast forward radiative transfer models and difficulties in error modeling. This talk focuses on the development, evaluation, and sensitivity analysis of a forward radar model integrated into CRTM. The forward radar model utilizes scattering properties obtained from hydrometeor lookup tables generated using the discrete dipole approximation. By utilizing CRTM instrument-specific coefficients, the model can calculate both reflectivity and attenuated reflectivity for any given radar instrument and zenith angles. Evaluation using CloudSat measurements demonstrates a strong agreement between simulations and observations when the input profiles of hydrometeors align with the measured reflectivity profiles.

Isaac Moradi↗

NASA NTRS2008

Lessons Learned from Previous Space-Borne Sounders as a Guide to Future Sounder Development

Space-borne radio sounding is considered to be the gold standard for electron-density (N(sub e)) measurements compared to other techniques even under low-density conditions, such as N(sub e) < 1/cu cm, when other techniques are known to experience difficulties. These reliable measurements are not restricted to in-situ N(sub e) determinations since a spaceborne sounder can provide vertical N(sub e) profiles (N(sub e)(h)) from the spacecraft altitude to the altitude of maximum N(sub e). Near-conjunction studies involving the International Satellites for Ionospheric Studies (ISIS) satellites in the topside ionosphere and Dynamics Explorer 2 (DE 2) near the altitude of the F-region peak density have verified that, even at the greatest distance from the sounder, the ISIS-derived N(sub e)(h) profiles agree with the DE-2 Langmuir-probe measurements to within about 30% over a density range of more than two decades. Space-borne sounders can also provide N(sub e) profiles along the magnetic-field B, by inverting echoes that are ducted along field-aligned irregularities (FAI), and can provide information about the terrain beneath the satellite by examining surface reflections in the frequency range above the ionospheric penetration frequency. Many nations have launched rocket and satellite radio sounders in geospace over more than 4 decades and there have been sounders on space-probes and in orbit around other planets. Here we will summarize some of the lessons learned from these accomplishments by analyzing data from radio sounders on the Alouette and ISIS satellites and the OEDIPUS and other rockets in the terrestrial ionosphere, the IMAGE satellite in the terrestrial magnetosphere, the Ulysses space probe in Jupiter's 10 plasma torus and the MARSIS satellite in orbit around Mars. The emphasis will be on information deduced concerning (1) fundamental plasma processes and gradients in N, and B in the vicinity of the sounders from sounder-stimulated plasma resonances and short-range echoes involving ion as well as electron motions, (2) the importance of the antenna orientation relative to B for the detection of different plasma resonances, (3) sounder-stimulated plasma phenomena, including FAI, when special plasma conditions are satisfied, (4) the minimum power required for long-range echoes, as indicated by echoes from frequency components of the transmitted pulse and by multiple ducted echoes, and (5) the terrain beneath the satellite from surface reflections. Knowledge of these results should enable the optimum design of a future sounder to satisfy specific science requirements with minimal spacecraft resources.

Benson, Robert F.↗

NASA NTRSDate not supplied

Enhancing Radiative Transfer Models for Optimized Assimilation of Microwave and Radar Observations

Radiative transfer models are extensively used for the assimilation of satellite observations into NWP models as well as retrieving geophysical products from satellite measurements. The Community Radiative Transfer Model (CRTM) is a community model developed by NOAA JCSDA and widely used for different purposes requiring RT calculations. CRTM requires bulk optical properties of hydrometeors in the form of lookup tables in order to perform all-sky RT calculations. However, the current cloud scattering lookup tables in CRTM assume spherical shapes for all frozen hydrometeors, whereas actual clouds contain frozen particles with diverse shapes. The first part of this talk presents the implementation and validation of a comprehensive Discrete Dipole Approximation (DDA) cloud scattering database into CRTM, specifically targeting microwave frequencies. The DDA technique proves effective in simulating the optical properties of non-spherical hydrometeors in the microwave region. The original DDA database assumes total random orientation in calculating single scattering properties. To generate the required mass scattering parameters for CRTM, the single scattering properties and water content dependent particle size distributions are used. The evaluation of results involved a collocated dataset comprising short-term forecasts from the Integrated Forecast System of the European Center for Medium-Range Weather Forecasts and satellite microwave data. The findings demonstrate that the DDA lookup tables significantly reduce discrepancies between simulated and observed values when compared to the Mie tables. Passive instruments lack the ability to provide vertically resolved measurements of clouds and precipitation, which can be obtained by active radar instruments. However, incorporating these active measurements into data assimilation systems presents challenges due to the absence of fast forward radiative transfer models and difficulties in error modeling. The second part of the talk focuses on the development, evaluation, and sensitivity analysis of a forward radar model integrated into CRTM. The forward radar model utilizes scattering properties obtained from hydrometeor lookup tables generated using the discrete dipole approximation. By utilizing CRTM instrument-specific coefficients, the model can calculate both reflectivity and attenuated reflectivity for any given radar instrument and zenith angles. Evaluation using CloudSat measurements demonstrates a strong agreement between simulations and observations when the input profiles of hydrometeors align with the measured reflectivity profiles.

Isaac Moradi↗

NASA NTRSDate not supplied

Optimizing Assimilation of Microwave and Radar Observations in the NWP Models

Radiative transfer models are extensively used for the assimilation of satellite observations into NWP models as well as retrieving geophysical products from satellite measurements. The Community Radiative Transfer Model (CRTM) is a community model developed by NOAA JCSDA and widely used for different purposes requiring RT calculations. CRTM requires bulk optical properties of hydrometeors in the form of lookup tables in order to perform all-sky RT calculations. However, the current cloud scattering lookup tables in CRTM assume spherical shapes for all frozen hydrometeors, whereas actual clouds contain frozen particles with diverse shapes. The first part of this talk presents the implementation and validation of a comprehensive Discrete Dipole Approximation (DDA) cloud scattering database into CRTM, specifically targeting microwave frequencies. The DDA technique proves effective in simulating the optical properties of non-spherical hydrometeors in the microwave region. The original DDA database assumes total random orientation in calculating single scattering properties. To generate the required mass scattering parameters for CRTM, the single scattering properties and water content dependent particle size distributions are used. The evaluation of results involved a collocated dataset comprising short-term forecasts from the Integrated Forecast System of the European Center for Medium-Range Weather Forecasts and satellite microwave data. The findings demonstrate that the DDA lookup tables significantly reduce discrepancies between simulated and observed values when compared to the Mie tables. Passive instruments lack the ability to provide vertically resolved measurements of clouds and precipitation, which can be obtained by active radar instruments. However, incorporating these active measurements into data assimilation systems presents challenges due to the absence of fast forward radiative transfer models and difficulties in error modeling. The second part of the talk focuses on the development, evaluation, and sensitivity analysis of a forward radar model integrated into CRTM. The forward radar model utilizes scattering properties obtained from hydrometeor lookup tables generated using the discrete dipole approximation. By utilizing CRTM instrument-specific coefficients, the model can calculate both reflectivity and attenuated reflectivity for any given radar instrument and zenith angles. Evaluation using CloudSat measurements demonstrates a strong agreement between simulations and observations when the input profiles of hydrometeors align with the measured reflectivity profiles.

Isaac Moradi↗

NASA NTRSDate not supplied

Assimilation of Spaceborne Microwave and Radar Observations

Radiative transfer models are extensively used for the assimilation of satellite observations into NWP models as well as retrieving geophysical products from satellite measurements. The Community Radiative Transfer Model (CRTM) is a community model developed by NOAA JCSDA and widely used for different purposes requiring RT calculations. CRTM requires bulk optical properties of hydrometeors in the form of lookup tables in order to perform all-sky RT calculations. However, the current cloud scattering lookup tables in CRTM assume spherical shapes for all frozen hydrometeors, whereas actual clouds contain frozen particles with diverse shapes. The first part of this talk presents the implementation and validation of a comprehensive Discrete Dipole Approximation (DDA) cloud scattering database into CRTM, specifically targeting microwave frequencies. The DDA technique proves effective in simulating the optical properties of non-spherical hydrometeors in the microwave region. The original DDA database assumes total random orientation in calculating single scattering properties. To generate the required mass scattering parameters for CRTM, the single scattering properties and water content dependent particle size distributions are used. The evaluation of results involved a collocated dataset comprising short-term forecasts from the Integrated Forecast System of the European Center for Medium-Range Weather Forecasts and satellite microwave data. The findings demonstrate that the DDA lookup tables significantly reduce discrepancies between simulated and observed values when compared to the Mie tables. Passive instruments lack the ability to provide vertically resolved measurements of clouds and precipitation, which can be obtained by active radar instruments. However, incorporating these active measurements into data assimilation systems presents challenges due to the absence of fast forward radiative transfer models and difficulties in error modeling. The second part of the talk focuses on the development, evaluation, and sensitivity analysis of a forward radar model integrated into CRTM. The forward radar model utilizes scattering properties obtained from hydrometeor lookup tables generated using the discrete dipole approximation. By utilizing CRTM instrument-specific coefficients, the model can calculate both reflectivity and attenuated reflectivity for any given radar instrument and zenith angles. Evaluation using CloudSat measurements demonstrates a strong agreement between simulations and observations when the input profiles of hydrometeors align with the measured reflectivity profiles.

Isaac Moradi↗

NASA NTRS1997

Topography of the Moon from the Clementine Lidar

Range measurements from the lidar instrument carried aboard the Clementine spacecraft have been used to produce an accurate global topographic model of the Moon. This paper discusses the function of the lidar; the acquisition, processing, and filtering of observations to produce a global topographic model; and the determination of parameters that define the fundamental shape of the Moon. Our topographic model: a 72nd degree and order spherical harmonic expansion of lunar radii, is designated Goddard Lunar Topography Model 2 (GLTM 2). This topographic field has an absolute vertical accuracy of approximately 100 m and a spatial resolution of 2.5 deg. The field shows that the Moon can be described as a sphere with maximum positive and negative deviations of approx. 8 km, both occurring on the farside, in the areas of the Korolev and South Pole-Aitken (S.P.-Aitken) basins. The amplitude spectrum of the topography shows more power at longer wavelengths as compared to previous models, owing to more complete sampling of the surface, particularly the farside. A comparison of elevations derived from the Clementine lidar to control point elevations from the Apollo laser altimeters indicates that measured relative topographic heights generally agree to within approx. 200 in over the maria. While the major axis of the lunar gravity field is aligned in the Earth-Moon direction, the major axis of topography is displaced from this line by approximately 10 deg to the cast and intersects the farside 24 deg north of the equator. The magnitude of impact basin topography is greater than the lunar flattening (approx. 2 km) and equatorial ellipticity (approx. 800 m), which imposes a significant challenge to interpreting the lunar figure. The floors of mare basins are shown to lie close to an equipotential surface, while the floors of unflooded large basins, except for S.P.-Aitken, lie above this equipotential. The radii of basin floors are thus consistent with a hydrostatic mechanism for the absence of significant farside maria except for S.P.-Aitken, whose depth and lack of mare require significant internal compositional and/or thermal heterogeneity. A macroscale surface roughness map shows that roughness at length scales of 10(exp 1) - 10(exp 2) km correlates with elevation and surface age.

Smith, David E.↗

NASA NTRS2012

Evidence for Two Separate but Interlaced Components of the Chromospheric Magnetic Field

Chromospheric fibrils are generally thought to trace out horizontal magnetic fields that fan out from flux concentrations in the photosphere. A high-resolution (0.2") image taken in the core of the Ca IJ854.2 nm line shows the dark fibrils within an active region remnant as fine, loop-like features that are aligned parallel to each other and have lengths on the order of a supergranular diameter (approx.30 Mm). Comparison with a line-of-sight magnetogram confirms that the fibrils are centered above intranetwork areas, with one end rooted just inside the neighboring plage or strong unipolar network but the other endpoint less clearly defined. Focusing on a particular arcade-like structure lying entirely on one side of a filament channel (large-scale polarity inversion), we find that the total amount of positive-polarity flux underlying this "fibril arcade' is 50 times greater than the total amount of negative-polarity flux. Thus, if the fibrils represent closed loops, they must consist of very weak fields (in terms of flux density), which are interpenetrated by a more vertical field that contains most of the flux. This surprising result suggests that the fibrils in unipolar regions connect the network to the nearby intranetwork flux, while the bulk of the network flux is diverted upward into the corona and connects to remote regions of the opposite polarity. We conclude that the chromospheric field near the edge of the network has an interlaced structure resembling that in sunspot penumbrae, with the fibrils representing the low-lying horizontal flux that remains trapped within the highly nonpotential chromospheric layer.

Muglach, K.↗