SEARCH · Search NASA

Results for “wind tunnel characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Separation bubble behavior for a NACA 23009 airfoil

Results are reported of experiments with smoke-wire flow visualization applied to characterizing the conditions conducive to formation of a separation bubble on an airfoil in low Re flow. An airfoil was used which spanned the test channel of the wind tunnel designed for low turbulence and noise. A wire coated with mineral oil was stretched across the channel upstream of the airfoil and heated. The smoke it gave off was flash-illuminated and photographed with ASA 3000 film. Extending the airfoil over the entire section yielded photographs that gave an essentially two-dimensional perspective. Angles of attack from 0-10 deg were investigated at Re of 33,000, 66,000, 100,000 and 133,000. Sample photographs illustrate the usefulness of the technique and apparatus in the flow regimes examined, particularly when used in conjunction with pressure tap data from the airfoil surface.

Fisher, S. S.↗

NASA NTRS2014

Shake Test Results and Dynamic Calibration Efforts for the Large Rotor Test Apparatus

Prior to the full-scale wind tunnel test of the UH-60A Airloads rotor, a shake test was completed on the Large Rotor Test Apparatus. The goal of the shake test was to characterize the oscillatory response of the test rig and provide a dynamic calibration of the balance to accurately measure vibratory hub loads. This paper provides a summary of the shake test results, including balance, shaft bending gauge, and accelerometer measurements. Sensitivity to hub mass and angle of attack were investigated during the shake test. Hub mass was found to have an important impact on the vibratory forces and moments measured at the balance, especially near the UH-60A 4/rev frequency. Comparisons were made between the accelerometer data and an existing finite-element model, showing agreement on mode shapes, but not on natural frequencies. Finally, the results of a simple dynamic calibration are presented, showing the effects of changes in hub mass. The results show that the shake test data can be used to correct in-plane loads measurements up to 10 Hz and normal loads up to 30 Hz.

Large Rotor Test Apparatus↗

NASA NTRS1997

System Dynamic Analysis of a Wind Tunnel Model with Applications to Improve Aerodynamic Data Quality

The research investigates the effect of wind tunnel model system dynamics on measured aerodynamic data. During wind tunnel tests designed to obtain lift and drag data, the required aerodynamic measurements are the steady-state balance forces and moments, pressures, and model attitude. However, the wind tunnel model system can be subjected to unsteady aerodynamic and inertial loads which result in oscillatory translations and angular rotations. The steady-state force balance and inertial model attitude measurements are obtained by filtering and averaging data taken during conditions of high model vibrations. The main goals of this research are to characterize the effects of model system dynamics on the measured steady-state aerodynamic data and develop a correction technique to compensate for dynamically induced errors. Equations of motion are formulated for the dynamic response of the model system subjected to arbitrary aerodynamic and inertial inputs. The resulting modal model is examined to study the effects of the model system dynamic response on the aerodynamic data. In particular, the equations of motion are used to describe the effect of dynamics on the inertial model attitude, or angle of attack, measurement system that is used routinely at the NASA Langley Research Center and other wind tunnel facilities throughout the world. This activity was prompted by the inertial model attitude sensor response observed during high levels of model vibration while testing in the National Transonic Facility at the NASA Langley Research Center. The inertial attitude sensor cannot distinguish between the gravitational acceleration and centrifugal accelerations associated with wind tunnel model system vibration, which results in a model attitude measurement bias error. Bias errors over an order of magnitude greater than the required device accuracy were found in the inertial model attitude measurements during dynamic testing of two model systems. Based on a theoretical modal approach, a method using measured vibration amplitudes and measured or calculated modal characteristics of the model system is developed to correct for dynamic bias errors in the model attitude measurements. The correction method is verified through dynamic response tests on two model systems and actual wind tunnel test data.

Buehrle, Ralph David↗

NASA NTRS2009

Ground/Flight Correlation of Aerodynamic Loads with Structural Response

United States Air Force Research Laboratory (AFRL) ground tests at the NASA Transonic Dynamics Tunnel (TDT) and NASA flight tests provide a basis and methodology for in-flight characterization of the aeroelastic performance through the monitoring of the fluid-structure interaction using surface flow sensors. NASA NF-15B flight tests provided a unique opportunity to test the correlation of aerodynamic loads with sectional flow attachment/detachment points, also known as flow bifurcation points (FBPs), as observed in previous wind tunnel tests. The NF-15B tail was instrumented with hot-film sensors and strain gages for measuring root-bending strains. These data were gathered via selected sideslip maneuvers performed at level flight and subsonic speeds. The aerodynamic loads generated by the sideslip maneuver resulted in root-bending strains and hot-film sensor signals near the stagnation region that were highly correlated. For the TDT tests, a flexible wing section developed under the AFRL SensorCraft program was instrumented with strain gages, accelerometers, and hot-film sensors at multiple span stations. The TDT tests provided data showing a gradual phase change between the FBP and the structural mode occurred during a resonant condition as the wings structural modes were excited by the tunnel-generated gusts.

Mangalam, Arun S.↗

NASA NTRS2006

Overview of Dynamic Test Techniques for Flight Dynamics Research at NASA LaRC (Invited)

An overview of dynamic test techniques used at NASA Langley Research Center on scale models to obtain a comprehensive flight dynamics characterization of aerospace vehicles is presented. Dynamic test techniques have been used at Langley Research Center since the 1920s. This paper will provide a partial overview of the current techniques available at Langley Research Center. The paper will discuss the dynamic scaling necessary to address the often hard-to-achieve similitude requirements for these techniques. Dynamic test techniques are categorized as captive, wind tunnel single degree-of-freedom and free-flying, and outside free-flying. The test facilities, technique specifications, data reduction, issues and future work are presented for each technique. The battery of tests conducted using the Blended Wing Body aircraft serves to illustrate how the techniques, when used together, are capable of characterizing the flight dynamics of a vehicle over a large range of critical flight conditions.

Owens, D. Bruce↗

NASA NTRS1985

Fixed gain and adaptive techniques for rotorcraft vibration control

The results of an analysis effort performed to demonstrate the feasibility of employing approximate dynamical models and frequency shaped cost functional control law desgin techniques for helicopter vibration suppression are presented. Both fixed gain and adaptive control designs based on linear second order dynamical models were implemented in a detailed Rotor Systems Research Aircraft (RSRA) simulation to validate these active vibration suppression control laws. Approximate models of fuselage flexibility were included in the RSRA simulation in order to more accurately characterize the structural dynamics. The results for both the fixed gain and adaptive approaches are promising and provide a foundation for pursuing further validation in more extensive simulation studies and in wind tunnel and/or flight tests.

Roy, R. H.↗

NASA NTRS1974

Review of NASA supercritical airfoils

NASA supercritical airfoils are characterized by a substantially reduced curvature of the midcord region of the upper surface together with increased camber near the trailing edge. The basic aerodynamic phenomena associated with the airfoils and representative wind tunnel results are discussed. The results indicate that the drag rise Mach numbers for NASA supercritical airfoils are 0.1 higher than for comparable NACA 6-series airfoils. A recent analytic method for predicting the aerodynamic characteristics of supercritical airfoils is described. The flight demonstration programs of three applications of supercritical airfoils utilizing the F-8, T-2C and F-111 as test beds are summarized.

Whitcomb, R. T.↗

NASA NTRS1977

Subsonic and supersonic aerodynamic characteristics of a supersonic cruise fighter model with a twisted and cambered wing with 74 deg sweep

A wind tunnel investigation has been conducted to determine the longitudinal and lateral aerodynamic characteristics of a model of a supersonic cruise fighter configuration with a design Mach number of 2.60. The configuration is characterized by a highly swept arrow wing twisted and cambered to minimize supersonic drag due to lift, twin wing mounted vertical tails, and an aft mounted integral underslung duel-engine pod. The investigation also included tests of the configuration with larger outboard vertical tails and with small nose strakes.

Morris, O. A.↗

NASA NTRS1979

Low-frequency broadband noise generated by a model rotor

Low-frequency broadband noise generated by model rotors is attributed to the interaction of ingested turbulence with the rotor blades. The influence of free-stream turbulence in the low-frequency broadband noise radiation from model rotors has been experimentally investigated. The turbulence was generated in the M.I.T. anechoic wind tunnel facility with the aid of bipolar grids of various sizes. The spectra and the intensity of the low-frequency broadband noise have been studied as a function of parameters which characterize the turbulence and of helicopter performance parameters. The location of the peak intensity was observed to be strongly dependent on the rotor-tip velocity and on the longitudinal integral scale of turbulence. The size scale of turbulence had negligible effect on the intensity of low-frequency broadband noise. The experimental data show good agreement with an ad hoc model based on unsteady aerodynamics.

Aravamudan, K. S.↗

NASA NTRS2019

Measurement and Analysis of Terminal Shock Oscillation and Buffet Forcing Functions on a Launch Vehicle Payload Fairing

The buffet loads on a launch vehicle payload shroud can be impacted by the unsteadiness associated with a terminal shock at high subsonic speeds. At these conditions, flow accelerates to supersonic speeds on the nose of the payload fairing and is terminated by a normal shock on the cylindrical section downstream of the nose cone/cylinder shoulder. The location of the terminal shock and associated separated boundary layer is affected by the freestream Mach number, Reynolds number, and the pitch/yaw of the launch vehicle. Furthermore, even when the freestream conditions and vehicle attitude are constant, this terminal shock oscillates on the surface of the vehicle. The time-varying surface pressure associated with the terminal shock results in unsteady aerodynamic loads that may interact with vehicle structural dynamic modes and the guidance and control of the vehicle. Buffet testing of a 3-percent scale rigid buffet model of a launch vehicle cargo configuration with a tangent-ogive payload shroud was conducted in 2012 and in 2016. Initial buffet forcing functions (BFFs) utilized a coarse pressure sensor distribution on the vehicle surface in which a single longitudinal station with eight sensors observed the terminal shock environment at Mach 0.90. An examination of these circumferential pressures reveal large impulse-like pressure fluctuations and an asymmetry in pressure when the vehicle is at a nonzeroangle of attack that result in high BFFs. Revisions to the shock integration region were made based on computational fluid dynamics and shadowgraph video of shock motion to better represent the BFFs and reduce the high loads resulting from this environment. To more clearly understand this terminal shock environment, a second wind tunnel test was conducted with a dense distribution of 256 sensors at the terminal shock location. These sensor arrays presents a unique opportunity to observe the unsteady terminal shock environment and to characterize the impact of various integration schemes on the BFFs. This paper presents a summary of the development of BFFs for this terminal shock and a detailed analyses of shock region pressure coefficients, coherence, BFFs, shock location time histories, and power spectral density to help guide development of BFFs for other launch vehicle test and analysis programs.

Piatak, David J.↗

NASA NTRS1991

Meeting Review: Airborne Aerosol Inlet Workshop

Proceedings from the Airborne Aerosol Inlet Workshop are presented. The two central topics of discussion were the role of aerosols in atmospheric processes and the difficulties in characterizing aerosols. The following topics were discussed during the working sessions: airborne observations to date; identification of inlet design issues; inlet modeling needs and directions; objectives for aircraft experiments; and future laboratory and wind tunnel studies.

Baumgardner, Darrel↗

NASA NTRS2015

Additive Manufacturing of Ultem Polymers and Composites

The objective of this project was to conduct additive manufacturing to produce aircraft engine components by Fused Deposition Modeling (FDM), using commercially available polyetherimdes Ultem 9085 and experimental Ultem 1000 filled with 10 chopped carbon fiber. A property comparison between FDM-printed and injection molded coupons for Ultem 9085, Ultem 1000 resin and the fiber-filled composite Ultem 1000 was carried out. Furthermore, an acoustic liner was printed from Ultem 9085 simulating conventional honeycomb structured liners and tested in a wind tunnel. Composite compressor inlet guide vanes were also printed using fiber-filled Ultem 1000 filaments and tested in a cascade rig. The fiber-filled Ultem 1000 filaments and composite vanes were characterized by scanning electron microscope (SEM) and acid digestion to determine the porosity of FDM-printed articles which ranged from 25-31. Coupons of Ultem 9085, experimental Ultem 1000 composites and XH6050 resin were tested at room temperature and 400F to evaluate their corresponding mechanical properties.

Polymer↗

NASA NTRS2020

Effects of Resistive Windscreens and Foam Inserts on The Acoustic Response of an In-Flow Phased Microphone Array

The effects of varying windscreen resistance and cavity foam treatments on the acoustic response of an in-flow phased microphone array have been characterized by recent experiments at ARC, GRC, and LaRC using common array and calibration source designs. New correction models have been developed and validated with results from recent impedance tube, anechoic chamber, and wind tunnel tests.

Wind tunnel aeroacoustics research↗

NASA NTRS1990

Aeolian removal of dust from radiator surfaces on Mars

Simulated radiator surfaces made of arc-textured Cu and Nb-1 percent-Zr and ion beam textured graphite and C-C composite were fabricated and their integrated spectral emittance characterized from 300 to 3000 K. A thin layer of aluminum oxide, basalt, or iron (III) oxide dust was then deposited on them, and they were subjected to low pressure winds in the Martian Surface Wind Tunnel. It was found that dust deposited on simulated radiator surfaces may or may not seriously lower their integrated spectral emittance, depending upon the characteristics of the dust. With Al2O3 there is no appreciable degradation of emittance on a dusted sample, with basaltic dust there is a 10 to 20 percent degradation, and with Fe2O3 a 20 to 40 percent degradation. It was also found that very high winds on dusted highly textured surfaces can result in their abrasion. Degradation in emittance due to abrasion was found to vary with radiator material. Arc-textured Cu and Nb-1 percent Zr was found to be more susceptible to emittance degradation than graphite or C-C composite. The most abrasion occurred at low angles, peaking at the 22.5 deg test samples.

Gaier, James R.↗

NASA NTRS1992

Experimental research of the aerodynamics of nozzles and plumes at hypersonic speeds

The purpose was to experimentally characterize the flow field created by the interaction of a single expansion ramp nozzle (SERN) flow with a hypersonic external stream. Data were obtained from a generic nozzle/afterbody model in the 3.5 Foot Hypersonic Wind Tunnel of the NASA Ames Research Center. The model design and test planning were performed in close cooperation with members of the National Aero-Space Plane (NASP) computational fluid dynamics (SFD) team, so that the measurements could be used in CFD code validation studies. Presented here is a description of the experiment, the extent of the measurements obtained, and the experimental results.

Keener, Earl R.↗

NASA NTRS1932

Problems concerning the stability and maneuverability of airplanes

The stability of an airplane can be easily determined by wind-tunnel tests, especially by simple tests with models mounted wind-vane fashion. However, each stability curve plotted by this method is valid only for a certain setting of the corresponding control surface, i.e., it characterizes the stability of the airplane with the control stick in a given position. The problems thus defined are studied from the point of view of longitudinal and transverse stability. Directional stability is not included in this study.

Biche, Jean↗

NASA NTRS2011

Instrumentation Development for Large Scale Hypersonic Inflatable Aerodynamic Decelerator Characterization

Hypersonic Inflatable Aerodynamic Decelerator (HIAD) technology is currently being considered for multiple atmospheric entry applications as the limitations of traditional entry vehicles have been reached. The Inflatable Re-entry Vehicle Experiment (IRVE) has successfully demonstrated this technology as a viable candidate with a 3.0 m diameter vehicle sub-orbital flight. To further this technology, large scale HIADs (6.0 8.5 m) must be developed and tested. To characterize the performance of large scale HIAD technology new instrumentation concepts must be developed to accommodate the flexible nature inflatable aeroshell. Many of the concepts that are under consideration for the HIAD FY12 subsonic wind tunnel test series are discussed below.

Swanson, Gregory T.↗

NASA NTRSDate not supplied

Spatially-Resolved Freestream Velocity Measurements at the NASA Langley 31-Inch Mach 10 Air Tunnel Using FLEET

Freestream velocity measurements in the NASA Langley 31-inch Mach 10 wind tunnel are reported in this paper using Femtosecond Laser Electronic Excitation Tagging (FLEET). The freestream measurements acquired during the January 2023 test campaign were the first direct measurement of freestream velocity in this hypersonic wind tunnel facility. Spatial distributions of time-averaged and instantaneous velocity measurements were obtained at all three typical wind tunnel freestream unit Reynolds number conditions of Re∞/L = 1.8∙106 m-1, 3.6∙106 m-1, and 6.4∙106 m-1, though the current paper focuses on centerline measurements for the three Re∞/L and spatial distributions for one Re∞/L. Measured values for time-averaged velocity and mean of the instantaneous velocity at the wind tunnel centerline agree within 5 m/s or 0.4% of the calculated velocity from the facility data acquisition system. Measurements acquired at locations away from the wind tunnel centerline reveal the spatial extent of the core flow of the hypersonic facility.

FLEET↗