Search NASA⌕ Search

SEARCH · Search NASA

Results for “wing aerodynamics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Effects of wing leading-edge flap deflections on subsonic longitudinal aerodynamic characteristics of a wing-fuselage configuration with a 44 deg swept wing

An investigation was conducted to determine the effects of wing leading-edge flap deflections on the subsonic longitudinal aerodynamic characteristics of a wing-fuselage configuration with a 44 deg swept wing. The tests were conducted at Mach numbers from 0.40 to 0.85, corresponding to Reynolds numbers (based on wing mean geometric chord) of 2.37 x 1,000,000 to 4.59 x 1,000,000 and at angles of attack from -3 deg to 22 deg. The configurations under study included a wing-fuselage configuration and a wing-fuselage-strake configuration. Each configuration had multisegmented, constant-chord leading-edge flaps which could be deflected independently or in various combinations.

Henderson, W. P.↗
NASA NTRS2007

Wind Tunnel Investigation of the Effects of Surface Porosity and Vertical Tail Placement on Slender Wing Vortex Flow Aerodynamics at Supersonic Speeds

A wind tunnel experiment was conducted in the NASA Langley Research Center (LaRC) Unitary Plan Wind Tunnel (UPWT) to determine the effects of passive surface porosity and vertical tail placement on vortex flow development and interactions about a general research fighter configuration at supersonic speeds. Optical flow measurement and flow visualization techniques were used that featured pressure sensitive paint (PSP), laser vapor screen (LVS), and schlieren, These techniques were combined with conventional electronically-scanned pressure (ESP) and six-component force and moment measurements to quantify and to visualize the effects of flow-through porosity applied to a wing leading edge extension (LEX) and the placement of centerline and twin vertical tails on the vortex-dominated flow field of a 65 cropped delta wing model. Test results were obtained at free-stream Mach numbers of 1.6, 1.8, and 2.1 and a Reynolds number per foot of 2.0 million. LEX porosity promoted a wing vortex-dominated flow field as a result of a diffusion and weakening of the LEX vortex. The redistribution of the vortex-induced suction pressures contributed to large nose-down pitching moment increments but did not significantly affect the vortex-induced lift. The trends associated with LEX porosity were unaffected by vertical tail placement. The centerline tail configuration generally provided more stable rolling moments and yawing moments compared to the twin wing-mounted vertical tails. The strength of a complex system of shock waves between the twin tails was reduced by LEX porosity.

Erickson, Gary E.↗
NASA NTRS1958

Aerodynamic Characteristics of a 45 Degree Swept-wing Fighter-Airplane Model and Aerodynamic Loads on Adjacent Stores and Missiles at Mach Numbers of 1.57, 1.87, 2.16, and 2.53

An investigation was performed in the Langley Unitary Plan wind tunnel to determine the aerodynamic characteristics of a model of a 450 swept-wing fighter airplane, and to determine the loads on attached stores and detached missiles in the presence of the model. Also included was a determination of aileron-spoiler effectiveness, aileron hinge moments, and the effects of wing modifications on model aerodynamic characteristics. Tests were performed at Mach numbers of 1.57, 1.87, 2.16, and 2.53. The Reynolds numbers for the tests, based on the mean aerodynamic chord of the wing, varied from about 0.9 x 10(exp 6) to 5 x 10(exp 6). The results are presented with minimum analysis.

Oehman, Waldo I↗
NASA NTRS1972

Aerodynamic characteristics of a large scale lift fan transport model with podded fans forward and lift cruise fans mounted above the wing

The aerodynamic characteristics of a large scale V/STOL transport model powered by tip-turbine driven lift fans were investigated. The model had four fans; the forward fans were mounted in pods forward of the wing at midsemispan. The aft fans were placed in cruise nacelles behind and above the wing. A cascade of variable camber exit louvers was placed behind each of the lift-cruise fans to turn the fan flow in the lift direction for hover and transition to wing supported flight. The wing of the model was mounted above the fuselage, had an aspect ratio of 5.8, sweepback of 35 deg at the quarter chord line and a taper ratio of 0.3. Various configurations of the model were tested to explore the transition speed range. Fan performance, turning effectiveness of the variable camber exit louvers, longitudinal and lateral-directional characteristics with fan operation in crossflow are presented.

Kirk, J. V.↗
NASA NTRS1974

Subsonic roll-damping characteristics of a series of wings

The aerodynamic damping in roll of a series of wings has been investigated in the Langley high-speed 7- by 10-foot tunnel at Mach numbers ranging from 0.2 to 0.8 by use of a forced oscillatory-roll technique. Tests were conducted on wings of aspect ratio 6 with sweep angles of 25, 35, and 45 deg and on 35 deg swept wings of aspect ratios 4 and 5.

Boyden, R. P.↗
NASA NTRS1993

An aerodynamic model for one and two degree of freedom wing rock of slender delta wings

The unsteady aerodynamic effects due to the separated flow around slender delta wings in motion were analyzed. By combining the unsteady flow field solution with the rigid body Euler equations of motion, self-induced wing rock motion is simulated. The aerodynamic model successfully captures the qualitative characteristics of wing rock observed in experiments. For the one degree of freedom in roll case, the model is used to look into the mechanisms of wing rock and to investigate the effects of various parameters, like angle of attack, yaw angle, displacement of the separation point, and wing inertia. To investigate the roll and yaw coupling for the delta wing, an additional degree of freedom is added. However, no limit cycle was observed in the two degree of freedom case. Nonetheless, the model can be used to apply various control laws to actively control wing rock using, for example, the displacement of the leading edge vortex separation point by inboard span wise blowing.

Hong, John↗
NASA NTRS2019

Experimental Aerodynamic Simulation of Scallop Ice Accretion on a Swept Wing

Understanding the aerodynamic impact of swept-wing ice accretions is a crucial component of the design of modern aircraft. Computer-simulation tools are commonly used to approximate ice shapes, so the necessary level of detail or fidelity of those simulated ice shapes must be understood relative to high-fidelity representations of the ice. Previous tests were performed in the NASA Icing Research Tunnel to acquire high-fidelity ice shapes. From this database, full-span artificial ice shapes were designed and manufactured for both an 8.9%-scale and 13.3%-scale semispan wing model of the CRM65 which has been established as the full-scale baseline for this swept-wing project. These models were tested in the Walter H. Beech wind tunnel at Wichita State University and at the ONERA F1 facility, respectively. The data collected in the Wichita St. University wind tunnel provided a low-Reynolds number baseline study while the pressurized F1 facility produced data over a wide range of Reynolds and Mach numbers with the highest Reynolds number studied being approximately Re=11.9x106. Past work focused on only three different fidelity variations for ice shapes based on multiple icing conditions. This work presents a more detailed investigation into several fidelity representations of a single highly three-dimensional scallop ice accretion. Sensitivity to roughness size and application technique on a low-fidelity smooth ice shape is described. The data indicate that the aerodynamic performance is not especially sensitive to the grit variations. An ice accretion code was also used to generate ice shapes for aerodynamic testing and comparisons. These ice shapes have a general appearance like the low-fidelity smooth ice shapes, but in this case, the computer-generated ice shape is significantly smaller. As such, the impact of that ice shape on the aerodynamic performance of the wing is reduced compared to the smooth ice shape based on the icing experiment for those same conditions. Spanwise discontinuities were also introduced to a low-fidelity ice shape in an attempt to quantify the impact of those variation in the high-fidelity ice shape. While the lift data indicate good agreement between the high-fidelity ice shapes and the low-fidelity ice shapes and the low-fidelity ice shapes with spanwise discontinuities, a closer investigation of the data suggests potential, significant differences in the flowfield. These results were similar at both facilities over the wide range of test conditions utilized.

Woodard, Brian↗
NASA NTRS1973

Calculation of unsteady transonic aerodynamics for oscillating wings with thickness.

An analytical approach is presented to account for some of the nonlinear characteristics of the transonic flow equation for finite thickness wings undergoing harmonic oscillation at sonic flight speed in an inviscid, shock-free fluid. The thickness effect is accounted for in the analysis through use of the steady local Mach number distribution over the wing at its mean position by employing the local linearization concept and a coordinate transformation. Computed results are compared with that of the linearized theory and experiments. Application to a flutter problem is shown.

Ruo, S. Y.↗
NASA NTRS1974

Calculation of unsteady transonic aerodynamics for oscillating wings with thickness (computer program)

A computer program has been developed to account approximately for the effects of finite wing thickness in the transonic potential flow over an oscillating wing of finite span. The program is based on the original sonic-box program of Rodemich and Andrew, and accounts for the nonuniform flow caused by finite thickness by application of the local linearization concept. A brief description of each subroutine is given, and the method of input is shown in detail. A sample problem as well as a complete listing of the computer program are presented.

Ruo, S. Y.↗
NASA NTRS1975

Calculation of unsteady transonic aerodynamics for oscillating wings with thickness

An analytical approach is presented to account for some of the nonlinear characteristics of the transonic flow equation for finite thickness wings undergoing harmonic oscillation at sonic flight speed in an inviscid, shock-free fluid. The thickness effect is accounted for in the analysis through use of the steady local Mach number distribution over the wing at its mean position by employing the local linearization concept and a coordinate transformation. Computed results are compared with that of the linearized theory and experiments. Based on the local linearization concept, an alternate formulation avoiding the limitations of the coordinate transformation method is presented.

Ruo, S. Y.↗
NASA NTRS1981

Prediction of aerodynamic characteristics for wings with extensive separations

The development of a simple yet effective technique for modelling the effects of trailing edge separation is discussed. The model encloses the low energy region with free vortex sheets coupled with a potential flow panel method. The technique includes an interation cycle between viscous and potential flow routines and its development from the two dimensional case to the three dimensional case is discussed. A description of the potential flow panel method, which is based on an internal Dirichlet boundary condition, is included.

Maskew, B.↗
NASA NTRS1984

A study of prediction methods for the high angle-of-attack aerodynamics of straight wings and fighter aircraft

Work is described dealing with two areas which are dominated by the nonlinear effects of vortex flows. The first area concerns the stall/spin characteristics of a general aviation wing with a modified leading edge. The second area concerns the high-angle-of-attack characteristics of high performance military aircraft. For each area, the governing phenomena are described as identified with the aid of existing experimental data. Existing analytical methods are reviewed, and the most promising method for each area used to perform some preliminary calculations. Based on these results, the strengths and weaknesses of the methods are defined, and research programs recommended to improve the methods as a result of better understanding of the flow mechanisms involved.

Mcmillan, O. J.↗