Search NASA⌕ Search

SEARCH · Search NASA

Results for “ACOUSTIC MEASUREMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Model helicopter blade slap at low tip speeds - Theoretical and experimental correlations

A novel data acquisition system has been designed which allows a transfer of pressure transducer and hot film data from a rotating frame to a stationary one, while collecting both loading and far field acoustic measurements simultaneously; this permits correlations to be made between experimental and theoretical predictions of blade loads and the resulting far field acoustics. The comparison of predicted acoustic pulse with experimental measurements has verified the assumptions made in the Widnall and Wolf (1980) theory for the case of low speed incompressible flow. The theory is also shown to be very sensitive to the interaction geometry and trajectory of the blade trailing vortex.

Chan, D. C.-L.↗
NASA NTRS1975

Analysis and correction of ground reflection effects in measured narrowband sound spectra using cepstral techniques

Ground reflections generate undesirable effects on acoustic measurements such as those conducted outdoors for jet noise research, aircraft certification, and motor vehicle regulation. Cepstral techniques developed in speech processing are adapted to identify echo delay time and to correct for ground reflection effects. A sample result is presented using an actual narrowband sound pressure level spectrum. The technique can readily be adapted to existing fast Fourier transform type spectrum measurement instrumentation to provide field measurements/of echo time delays.

Miles, J. H.↗
NASA NTRS1975

Analysis and correction of ground reflection effects in measured narrowband sound spectra using cepstral techniques

Ground reflections generate undesirable effects on acoustic measurements such as those conducted outdoors for jet noise research, aircraft certification, and motor vehicle regulation. This paper shows how cepstral techniques developed in speech processing can be adapted to identify the echo delay time and to correct for ground reflection effects. A sample result is presented using an actual narrowband sound pressure level spectrum. The technique can readily be adapted to existing fast Fourier transform type spectrum measurement instrumentation to provide field measurement of echo time delays.

Miles, J. H.↗
NASA NTRS1984

The effect of forward flight on the noise and flow field of inverted profile jets

Noise and flow field measurements are reported for an inverted profile coannular jet (where the annular jet speed exceeds the center jet speed) under simulated flight conditions. The annular and center jets were cold and both were operated subsonically. Forward flight was simulated by placing the coannular jet inside a larger open jet. Acoustic measurements show the effects of inverted profile shape and simulated flight on far field directivity, total radiated power, and spectral content. Measurements of total acoustic power demonstrate that the acoustic efficiency of inverted profile jets is about 3 dB less than the efficiency of 'top hat' profile jets, and that the noise decreases as the seventh power of the relative jet velocity in the limit of small flight velocity. Flow measurements demonstrate that the jet spreading parameter scales the thickness of the outer shear layer and the passage frequencies of the large turbulence scales. Comparisons between the turbulence time scales and the noise spectra suggest that coherent noise sources may become more important in forward flight.

Petersen, R. A.↗
NASA NTRS2015

Noise Measurements of High Aspect Ratio Distributed Exhaust Systems

This paper covers far-field acoustic measurements of a family of rectangular nozzles with aspect ratio 8, in the high subsonic flow regime. Several variations of nozzle geometry, commonly proposed for embedded exhaust systems, are explored, including bevels, slants, single broad chevrons and notches, and internal septae. Far-field acoustic results, presented previously for the simple rectangular nozzle, showed that increasing aspect ratio increases the high frequency noise, especially directed in the plane containing the minor axis of the nozzle. Detailed changes to the nozzle geometry generally made little difference in the noise, and the differences were greatest at low speed. Having an extended lip on one broad side ('bevel') did produce up to 3dB more noise in all directions, while extending the lip on the narrow side ('slant') produced up to 2dB more noise, primarily on the side with the extension. Adding a single, non-intrusive chevron, made no significant change to the noise, while inverting the chevron ('notch') produced up to 2dB increase in the noise. Having internal walls ('septae') within the nozzle, such as would be required for structural support or when multiple fan ducts are aggregated, reduced the noise of the rectangular jet, but could produce a highly directional shedding tone from the septae trailing edges. Finally, a nozzle with both septae and a beveled nozzle, representative of the exhaust system envisioned for a distributed propulsion aircraft with a common rectangular duct, produced almost as much noise as the beveled nozzle, with the septae not contributing much reduction in noise.

Noise↗
NASA NTRS2015

Noise Measurements of High Aspect Ratio Distributed Exhaust Systems

This paper covers far-field acoustic measurements of a family of rectangular nozzles with aspect ratio 8, in the high subsonic flow regime. Several variations of nozzle geometry, commonly found in embedded exhaust systems, are explored, including bevels, slants, single broad chevrons and notches, and internal septae. Far-field acoustic results, presented previously for the simple rectangular nozzle, showed that increasing aspect ratio increases the high frequency noise, especially directed in the plane containing the minor axis of the nozzle. Detailed changes to the nozzle geometry generally made little difference in the noise, and the differences were greatest at low speed. Having an extended lip on one broad side (bevel) did produce up to 3 decibels more noise in all directions, while extending the lip on the narrow side (slant) produced up to 2 decibels more noise, primarily on the side with the extension. Adding a single, non-intrusive chevron, made no significant change to the noise, while inverting the chevron (notch) produced up to 2decibels increase in the noise. Having internal walls (septae) within the nozzle, such as would be required for structural support or when multiple fan ducts are aggregated, reduced the noise of the rectangular jet, but could produce a highly directional shedding tone from the septae trailing edges. Finally, a nozzle with both septae and a beveled nozzle, representative of the exhaust system envisioned for a distributed electric propulsion aircraft with a common rectangular duct, produced almost as much noise as the beveled nozzle, with the septae not contributing much reduction in noise.

Noise↗
NASA NTRS2014

Analysis of Dual Rotating Rake Data from the NASA Glenn Advanced Noise Control Fan Duct with Artificial Sources

The Rotating Rake mode measurement system was designed to measure acoustic duct modes generated by a fan stage. Initially, the mode amplitudes and phases were quantified from a single rake measurement at one axial location. To directly measure the modes propagating in both directions within a duct, a second rake was mounted to the rotating system with an offset in both the axial and the azimuthal directions. The rotating rake data analysis technique was then extended to include the data measured by the second rake. The analysis resulted in a set of circumferential mode levels at each of the two rake microphone locations. Radial basis functions were then least-squares fit to this data to obtain the radial mode amplitudes for the modes propagating in both directions within the duct. Validation experiments have been conducted using artificial acoustic sources. Results are shown for the measurement of the standing waves in the duct from sound generated by one and two acoustic sources that are separated into the component modes propagating in both directions within the duct. Measured reflection coefficients from the open end of the duct are compared to analytical predictions.

Noise↗
NASA NTRS2007

Measurement and Characterization of Helicopter Noise in Steady-State and Maneuvering Flight

A special acoustic flight test program was performed on the Bell 206B helicopter outfitted with an in-flight microphone boom/array attached to the helicopter while simultaneous acoustic measurements were made using a linear ground array of microphones arranged to be perpendicular to the flight path. Air and ground noise measurements were made in steady-state longitudinal and steady turning flight, and during selected dynamic maneuvers. Special instrumentation, including direct measurement of the helicopter s longitudinal tip-path-plane (TPP) angle, Differential Global Positioning System (DGPS) and Inertial Navigation Unit (INU) measurements, and a pursuit guidance display were used to measure important noise controlling parameters and to make the task of flying precise operating conditions and flight track easier for the pilot. Special care was also made to test only in very low winds. The resulting acoustic data is of relatively high quality and shows the value of carefully monitoring and controlling the helicopter s performance state. This paper has shown experimentally, that microphones close to the helicopter can be used to estimate the specific noise sources that radiate to the far field, if the microphones are positioned correctly relative to the noise source. Directivity patterns for steady, turning flight were also developed, for the first time, and connected to the turning performance of the helicopter. Some of the acoustic benefits of combining normally separated flight segments (i.e. an accelerated segment and a descending segment) were also demonstrated.

Schmitz, Fredric H.↗
DOE OSTI2020

Dynamics of Gas Bubbles From a Submarine Hydrocarbon Seep Within the Hydrate Stability Zone

We validate a new model for mass transfer and bubble transport for natural seeps on the continental margins using an integrated observation of a seep at 883 m in the Northern Gulf of Mexico. In the model, mass transfer is assumed to transition from clean to dirty bubble mass transfer rates following a characteristic hydrate formation time that depends on the initial bubble surface area and the hydrate subcooling. We show that buoyancy-induced upwelling is negligible for the bubble stream. We initialize the model using precise data observed at the seafloor and validate the model results to optical and acoustic measurements within the bubble stream. The model accurately predicts the acoustic attenuation of the bubble flare by lateral spreading and bubble shrinkage throughout the water column. In conclusion, the model shows that up to 99.4% by mass of the released gases from this seep dissolves into the ocean within the hydrate stability zone.

03 NATURAL GAS↗
NASA NTRS1974

Cascade tests of serrated leading edge blading at high subsonic speeds

Cascade tests of two-dimensional fan rotor blade rows were performed to investigate the effects of leading edge serration on acoustic and aerodynamic performance. The test configurations covered a range of serration tooth geometries. Tests were performed to investigate effects of inlet air angle and velocity on performance. Aerodynamic performance was determined by flow surveys at the mid-span of the blade exit. Acoustic performance was determined by wake turbulence surveys and sound measurements in the semireverberent exhaust chamber. Measured acoustic and aerodynamic performance was comparable and indicated that a serration length of about six percent blade chord yields minimum noise generation and minimum total pressure losses.

Smith, E. G.↗
NASA NTRS1980

Statistical energy analysis of complex structures, phase 2

A method for estimating the structural vibration properties of complex systems in high frequency environments was investigated. The structure analyzed was the Materials Experiment Assembly, (MEA), which is a portion of the OST-2A payload for the space transportation system. Statistical energy analysis (SEA) techniques were used to model the structure and predict the structural element response to acoustic excitation. A comparison of the intial response predictions and measured acoustic test data is presented. The conclusions indicate that: the SEA predicted the response of primary structure to acoustic excitation over a wide range of frequencies; and the contribution of mechanically induced random vibration to the total MEA is not significant.

Trudell, R. W.↗
NASA NTRS1981

Design, fabrication and test of last cut Follower

An optical device for following the cut in mining operations is described, and the results of acceptance testing reported. A measuring accuracy of + or - 1/16 inch was demonstrated. Preliminary results on longwall testing with the device mounted on a shearer are presented. Roof profiles measured during tramming and during cutting are presented. Comparison of acoustic measurements with optical measurement of the roof profiles indicates close agreement.

Ashley, P. R.↗
NASA NTRS1988

Aerodynamic flow quality and acoustic characteristics of the 40- by 80-foot test section circuit of the National Full-Scale Aerodynamic Complex

The 40- by 80-foot wind tunnel circuit of the National Full-Scale Aerodynamic Complex (NFAC) has recently undergone major modifications and subsequently completed final acceptance testing. The initial testing and calibration of the wind tunnel are described and in many cases these results are compared with predictions derived from model tests and theoretical analyses. The wind tunnel meets or exceeds essentially all performance objectives. The facility runs smoothly and routinely at its maximum test-section velocity of 300 knots (Mach number = 0.45). An effective cooling air exchange system enables the wind tunnel to operate indefinitely at this maximum power condition. Throughout the operating envelope of the wind tunnel the test-section dynamic pressure is uniform to within + or - 0.5 deg, and the axial component of turbulence is generally less than 0.5 percent. Acoustic measurements indicate that, due to the low noise fans and acoustic treatment in the wind-tunnel circuit and test section, the background noise level in the test section is comparable to other large-scale acoustic wind tunnels in the United States and abroad.

Olson, Lawrence E.↗
NASA NTRS2003

Novel Engineering and Fabrication Techniques Tested in Low-Noise- Research Fan Blades

A major source of fan noise in commercial turbofan engines is the interaction of the wake from the fan blades with the stationary vanes (stators) directly behind them. The Trailing Edge Blowing (TEB) project team at the NASA Glenn Research Center designed and fabricated new fan blades to study the effects of fan trailing edge blowing as a potential noise-reduction concept. The intent is to fill the rotor wake by supplying air to the rotor blade trailing edge at the proper conditions to minimize the wake deficit, and thus generate less noise. The TEB hardware is designed for the Active Noise Control Fan (ANCF) test rig in Glenn's Aeroacoustic Propulsion Laboratory. For this test, the air is fed from an external supply through the shaft of the rig. It is distributed to the base of each blade through an impeller, where it is forced into a plenum at the core of each blade. In actual engine configuration, air would most likely be bled from the compressor, but only at times when noise is an issue, such as takeoffs and landings. Glenn researchers designed and manufactured the blades in-house, using new techniques and concepts. The skins, which were designed for maximum strength in the directions of highest stress, were molded from multiple layers of carbon fiber. Considerable use was made of rapid prototyping techniques, such as laser sintering. The core was sintered from a lightweight polymer, and the retainer was CNC-machined (computer numerical control machined) from aluminum. All the components were joined with a cold-cure aerospace adhesive. These techniques and processes reduced the overall cost and allowed the new concept to be studied much sooner than would be possible using traditional fabrication methods. Since this test rig did not support the use of blade-monitoring techniques such as strain gauges, extensive bench testing was required to qualify the design. The blades were examined using a variety of methods including holography, pull tests (cyclic and failure), shake tests, rap tests, and nondestructive inspection. Acoustic testing of the ANCF fan using TEB has been ongoing since January of 2001. The fan has completed about 100 hr of testing with no structural, vibrational, or fatigue problems. Far-field acoustic measurements, in-duct mode measurements, precise hot wire surveys, and detailed performance measurements are providing data for evaluating the concept. The far-field noise data show that tone noise was reduced significantly with the initial ANCF TEB fan design. In addition, a significant reduction in unsteady stator loading has been measured, indicating the potential for stator broadband noise reduction. The acoustic benefits will be assessed and important design parameters identified to improve the ability to fully exploit any benefit provided by this technique. On the basis of the success of trailing edge blowing, Glenn plans to continue this research with a higher speed, higher pressure ratio fan operating in an acoustic wind tunnel to simulate flight conditions.

Cunningham, Cameron C.↗
NASA NTRS2014

Subscale Acoustic Testing: Comparison of ALAT and ASMAT

The liftoff phase induces acoustic loading over a broad frequency range for a launch vehicle. These external acoustic environments are then used in the prediction of internal vibration responses of the vehicle and components which result in the qualification levels. Thus, predicting these liftoff acoustic environments is critical to the design requirements of any launch vehicle. If there is a significant amount of uncertainty in the predictions or if acoustic mitigation options must be implemented, a subscale acoustic test is a feasible pre-launch test option. This paper compares the acoustic measurements of two different subscale tests: the 2% Ares Liftoff Acoustic Test conducted at Stennis Space Center and the 5% Ares I Scale Model Acoustic Test conducted at Marshall Space Flight Center.

Houston, Janice D.↗
NASA NTRSDate not supplied

Evaluation of a Variable Facesheet Liner Configuration in Grazing Incidence for Broadband Noise Reduction

Abstract Tests were conducted in the NASA Langley Grazing Flow Impedance Tube (GFIT) to determine the broadband noise reduction capability of a variable facesheet liner. Three uniform liners were designed to achieve sound absorption over distinct frequency regimes at Mach 0.0. Each liner was fabricated and tested in the GFIT at sound pressure levels of 120 and 140 dB, and at tangential flow velocities up to Mach 0.5. A variable facesheet liner was fabricated to combine the geometries of these three liners, such that the facesheet geometry (hole diameter and porosity) was varied across the liner surface. The Prony method was used to educe the impedance of each sample, and these impedances were input to the CHE (Convected Helmholtz Equation) propagation code to predict the acoustic pressure profiles in the GFIT. Comparisons of predicted and measured acoustic pressure profiles were used to confirm the uniformity of all four liners, and to demonstrate the suitability of the CHE code in analysis of the variable facesheet concept. Results showed good comparison at no flow and Mach 0.3, and acceptable comparison at Mach 0.5. The variable facesheet liner provides enhanced broadband noise reduction at the no-flow condition for which it was designed, but further optimization is needed to target flow conditions.

acoustic↗
NASA NTRSDate not supplied

Evaluation of a Variable Facesheet Liner Configuration in Grazing Incidence for Broadband Noise Reduction

Tests were conducted in the NASA Langley Grazing Flow Impedance Tube (GFIT) to determine the broadband noise reduction capability of a variable facesheet liner. Three uniform liners were designed to achieve sound absorption over distinct frequency regimes at Mach 0.0. Each liner was fabricated and tested in the GFIT at sound pressure levels of 120 and 140 dB, and at tangential flow velocities up to Mach 0.5. A variable facesheet liner was fabricated to combine the geometries of these three liners, such that the facesheet geometry (hole diameter and porosity) was varied across the liner surface. The Prony method was used to educe the impedance of each sample, and these impedances were input to the CHE (Convected Helmholtz Equation) propagation code to predict the acoustic pressure profiles in the GFIT. Comparisons of predicted and measured acoustic pressure profiles were used to confirm the uniformity of all four liners, and to demonstrate the suitability of the CHE code in the analysis of the variable facesheet concept. Results showed good comparison at no flow and at Mach 0.3, and acceptable comparison at Mach 0.5. The variable facesheet liner provided enhanced broadband noise reduction at the no-flow condition for which it was designed, but further optimization is needed to target flow conditions.

acoustic↗