Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIRCRAFT CONFIGURATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

A fundamental comparison of canard and conventional configurations

This paper examines the relative efficiency of canard, tandem, and aft-tailed aircraft configurations through analysis of an elementary lifting system. Stability and trim requirements are imposed upon the system and its C sub L(max), drag, and structural weight are studied as its geometry varies over a wide range of possible configurations. During the course of the analysis, two general solutions emerge for minimum induced drag as a function of the geometry and the division of lift between the surfaces of such a system - one for fixed span and the other for fixed weight. The conclusion is that the pre-eminence of the conventional aft-tailed configuration has a sound fundamental basis, but that there may be some room for improvement.

Mcgeer, T.↗
NASA NTRS1988

Effects of symmetric and asymmetric modes on transonic aeroelastic characteristics of full-span wing-body configurations

To accurately study the transonic aeroelastic characteristics, it is important to model the full aircraft configuration, including asymmetry. Recently, an accurate method of computing unsteady transonic flows on full-span wing-body configurations was developed using the transonic potential flow theory. In this work, the method is further developed to account for the aeroelasticity of full-span wing-body configurations. This is accomplished by simultaneously integrating the unsteady aerodynamic forces and modal structural equations of the wing-body configurations. To validate the method, aeroelastic computations are made for a wing-body configuration with a rectangular wing. The aeroelastic responses of this configuration are correlated with the responses of a similar isolated wing. The comparisons are favorable. Aeroelastic computations associated with symmetric and asymmetric modes are also made to study the influence of modal asymmetry on responses. This new development is further illustrated by computing aeroelastic characteristics of a typical fighter aircraft. The results from this study will be useful in accurately computing the transonic flutter boundaries of aircraft, including those associated with asymmetric modes.

Guruswamy, Guru P.↗
NASA NTRS1978

GASP- General Aviation Synthesis Program. Volume 5: Weight

Subroutines for determining the weights of propulsion system related components and the airframe components of an aircraft configuration are presented. Subroutines that deal with design load conditions, aircraft balance, and tail sizing are included. Options for turbine and internal combustion engines are provided.

Hague, D.↗
NASA NTRS1992

Aircraft concept optimization using the global sensitivity approach and parametric multiobjective figures of merit

An extension of our parametric multidisciplinary optimization method to include design results connecting multiple objective functions is presented. New insight into the effect of the figure of merit (objective function) on aircraft configuration size and shape is demonstrated using this technique. An aircraft concept, subject to performance and aerodynamic constraints, is optimized using the global sensitivity equation method for a wide range of objective functions. These figures of merit are described parametrically such that a series of multiobjective optimal solutions can be obtained. Computational speed is facilitated by use of algebraic representations of the system technologies. Using this method, the evolution of an optimum design from one objective function to another is demonstrated. Specifically, combinations of minimum takeoff gross weight, fuel weight, and maximum cruise performance and productivity parameters are used as objective functions.

Malone, Brett↗
NASA NTRS2011

Analysis of Asymmetric Aircraft Aerodynamics Due to an Experimental Wing Glove

Aerodynamic computational fluid dynamics analysis of a wing glove attached to one wing of a business jet is presented and discussed. A wing glove placed on only one wing will produce asymmetric aerodynamic effects that will result in overall changes in the forces and moments acting on the aircraft. These changes, referred to as deltas, need to be determined and quantified to ensure that the wing glove does not have a significant effect on the aircraft flight characteristics. TRANAIR (Calmar Research Corporation, Cato, New York), a nonlinear full potential solver, and Star-CCM+ (CD-adapco, Melville, New York), a finite volume full Reynolds-averaged Navier-Stokes computational fluid dynamics solver, are used to analyze a full aircraft with and without the glove at a variety of flight conditions, aircraft configurations, and angles of attack and sideslip. Changes in the aircraft lift, drag, and side force along with roll, pitch, and yaw are presented. Span lift and moment distributions are also presented for a more detailed look at the effects of the glove on the aircraft. Aerodynamic flow phenomena due to the addition of the glove are discussed. Results show that the glove produces only small changes in the aerodynamic forces and moments acting on the aircraft, most of which are insignificant.

Hartshorn, Fletcher↗
NASA NTRS2014

Aerodynamic Analysis of the Truss-Braced Wing Aircraft Using Vortex-Lattice Superposition Approach

The SUGAR Truss-BracedWing (TBW) aircraft concept is a Boeing-developed N+3 aircraft configuration funded by NASA ARMD FixedWing Project. This future generation transport aircraft concept is designed to be aerodynamically efficient by employing a high aspect ratio wing design. The aspect ratio of the TBW is on the order of 14 which is significantly greater than those of current generation transport aircraft. This paper presents a recent aerodynamic analysis of the TBW aircraft using a conceptual vortex-lattice aerodynamic tool VORLAX and an aerodynamic superposition approach. Based on the underlying linear potential flow theory, the principle of aerodynamic superposition is leveraged to deal with the complex aerodynamic configuration of the TBW. By decomposing the full configuration of the TBW into individual aerodynamic lifting components, the total aerodynamic characteristics of the full configuration can be estimated from the contributions of the individual components. The aerodynamic superposition approach shows excellent agreement with CFD results computed by FUN3D, USM3D, and STAR-CCM+.

vortex lattice method↗
NASA NTRS2016

Imparting Barely Visible Impact Damage to a Stitched Composite Large-Scale Pressure Box

The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) is a concept that was developed by The Boeing Company to address the complex structural design aspects associated with a pressurized hybrid wing body (HWB) aircraft configuration, which has been a focus of the NASA Environmentally Responsible Aviation Project. The NASA-Boeing structural development for the HWB aircraft culminated in testing of the multi-bay box, which is an 80%-scale representation of the pressurized center-body section. This structure was tested in the NASA Langley Research Center Combined Loads Test System facility. As part of this testing, barely visible impact damage was imparted to the interior and exterior of the test article to demonstrate compliance with a condition representative of the requirements for Category 1 damaged composite structure as defined by the Federal Aviation Regulations. Interior impacts were imparted using an existing spring-loaded impactor, while the exterior impacts were imparted using a newly designed, gravity-driven impactor. This paper describes the impacts to the test article, and the design of the gravitydriven guided-weight impactor. The guided-weight impactor proved to be a very reliable method to impart barely visible impact damage in locations which are not easily accessible for a traditional drop-weight impactor, while at the same time having the capability to be highly configurable for use on other aircraft structures.

Lovejoy, Andrew E.↗
NASA NTRS1996

Utilization of an agility assessment module in analysis and optimization of preliminary fighter configuration

A study has been conducted to develop and to analyze a FORTRAN computer code for performing agility analysis on fighter aircraft configurations. This program is one of the modules of the NASA Ames ACSYNT (AirCraft SYNThesis) design code. The background of the agility research in the aircraft industry and a survey of a few agility metrics are discussed. The methodology, techniques, and models developed for the code are presented. The validity of the existing code was evaluated by comparing with existing flight test data. A FORTRAN program was developed for a specific metric, PM (Pointing Margin), as part of the agility module. Example trade studies using the agility module along with ACSYNT were conducted using a McDonnell Douglas F/A-18 Hornet aircraft model. Tile sensitivity of thrust loading, wing loading, and thrust vectoring on agility criteria were investigated. The module can compare the agility potential between different configurations and has capability to optimize agility performance in the preliminary design process. This research provides a new and useful design tool for analyzing fighter performance during air combat engagements in the preliminary design.

Ngan, Angelen↗
NASA NTRS1975

An investigation of airflow over the aft portions of a variable sweep fighter configuration

An investigation of air flow over the aft portions of a variable sweep fighter aircraft configuration was made. Tests conducted in the unitary plan wind tunnel at Mach number 2.16 included measurements of forces, moments, and local static pressures as well as visual recordings of the air flow. An aerodynamic analytical prediction method was evaluated when used in data comparison at angles of attack of 0, 5, and 15 degrees. The results indicate that in supersonic flow the typical outboard located twin vertical tail arrangement tends to provide a more positive increment in normal-force on the afterbody fuselage and the horizontal tail than a single center-mounted vertical tail of similar planform shape. In addition, the results indicate that a method for aerodynamic analysis of wing-body-tail configurations currently available can provide reasonable estimates of pressure coefficient distributions on configurations in regions of complex supersonic flow. At this time, however, the available analytical method cannot adequately replace experimental wind tunnel tests for determining the supersonic flow environment of a given configuration.

Graves, E. B.↗
NASA NTRS1981

Numerical and classical analysis of V/STOL aircraft using selected propulsion systems

The development needed for the evolution of selected V/STOL research vehicles into optimized antisubmarine warfare (ASW) aircraft configurations, using numerical procedures and traditional analytical methods, has been examined. Three propulsion systems, which represent state-of-the-art development aimed at solving the thrust-vectoring and attitude-control problems of V/STOL aircraft, are analyzed. The use of NASA computer programs for aircraft synthesis (ACSYNT), and for optimizing configurations (COMMIN), coupled with contractor-supplied propulsion system data provides for accurate performance prediction of the selected ASW configurations. Particular emphasis on the transition phase between the research vehicle and the optimized configuration demonstrates the strengths and weaknesses of using generic research aircraft instead of building prototypes to demonstrate new technology

Wilson, S. B., III↗
NASA NTRS1977

FCAP - A new tool for the performance and structural analysis for complex flexible aircraft with active control

A very general formulation has been developed for the analysis of complex flexible-aircraft configurations in presence of active control. The formulation is incorporated into a computer program, Flight Control Analysis Program (FCAP), which is designed in a modular fashion to incorporate aircraft dynamics and aerodynamics for complex configurations, as well as sensor, actuator and control logic element dynamics. Formulation of the total aircraft dynamic system is accomplished in matrix form by casting equations in state vector format. The system stability and performance are determined in either the frequency or time domain using classical analysis techniques. Fully unsteady aerodynamics is used for the evaluation of the flutter characteristics as well as the gust response of the aircraft.

Morino, L.↗
NASA NTRS1974

Conceptual design studies of 1985 commercial VTOL transports that utilized rotors, Volume 1

Results of conceptual design studies of commercial rotary wing transport aircraft for the 1985 time period are presented. Two aircraft configurations, a tandem helicopter and a tilt rotor, were designed for a 200 nautical mile short haul mission with an upper limit of 100 passengers. In addition to the baseline aircraft two further designs of each configuration are included to assess the impact of external noise design criteria on the aircraft size, weight, and cost.

Magee, J. P.↗
NASA NTRS1978

Study of aerodynamic technology for VSTOL fighter attack aircraft

Vertical short takeoff aircraft capability, supersonic dash capability, and transonic agility were investigated for the development of Fighter/attack aircraft to be accommodated on ships smaller than present aircraft carriers. Topics covered include: (1) description of viable V/STOL fighter/attack configuration (a high wing, close-coupled canard, twin-engine, control configured aircraft) which meets or exceeds specified levels of vehicle performance; (2) estimates of vehicle aerodynamic characteristics and the methodology utilized to generate them; (3) description of propulsion system characteristics and vehicle mass properties; (4) identification of areas of aerodynamic uncertainty; and (5) a test program to investigate the areas of aerodynamic uncertainty in the conventional flight mode.

Burhans, W., Jr.↗