Search NASA⌕ Search

SEARCH · Search NASA

Results for “ALUMINUM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

High speed manufacturing of aluminum alloy 7075 tubing by Shear Assisted Processing and Extrusion (ShAPE)

Shear assisted processing and extrusion (ShAPE) was used to extrude aluminum alloy 7075 tubing at speeds up to 12.2 m/min. This is in comparison to 2.0 m/min which is generally the limit for conventionally extruded 7075. The increased speed is primarily attributed to more extensive shear deformation, compared to conventional extrusion, which results in a high density of low angle grain boundaries that facilitate continued deformation and delay the onset of surface tearing. Mechanical testing after heat treating to the T6 condition gave an ultimate tensile strength of 565.3 ± 4.6 MPa, yield strength of 495.7 ± 8.7 MPa, and elongation of 16.8 ± 0.8%. Strength values exceed the ASTM minimum standard and are on par with ASM typical values, while elongation was substantially improved compared to 7 and 11% for the ASTM and ASM values respectively. Finally, it was observed that low temperature extrusion at 341 °C and 40 rpm gave superior material properties in the T6 condition compared to high temperature extrusion at 441 °C and 120 rpm due to variances in nanoscale second phase size and distribution.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Manufacture aluminum alloy tube from powder with a single-step extrusion via ShAPE

Mechanical performance of aluminum in terms of strength, wear and corrosion resistance, especially high-temperature strength has been shown to improve with the addition of transition metal (TM) elements of Fe, Cr, and Ti. However, these feedstock materials occur as powders. As such, the traditional fabrication process is complex and expensive because it requires multiple procedures and consumes considerable energy. This study developed Shear Assisted Processing and Extrusion (ShAPE) as a single-step process that manufactures tubes directly from Al-TM powders obtained via gas atomization. Meter-long Al-TM alloy tubes are extruded from powders with different processing conditions. The ShAPE tubes have very low porosity and the average density is 2.94 kg/cm 3 , which is equal to or higher than parts fabricated by hot extrusion and sintering. The powder-to-tube fabrication process was revealed and discussed by examining the microstructural evolution. The Vickers hardness of ShAPE tubes ranges from 110 to 140 HV through wall thickness and at different extrusion speeds. The variation in hardness was correlated with the extent of refinement of intermetallics and attributed to the shear deformation per unit extrusion length. Energy cost analysis shows that ShAPE save ~60% energy compared to the conventional sintering and extrusion processes. Results indicate ShAPE is a low-cost, high-efficiency manufacturing process for producing tubes from metallic powders.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High performance aluminum-air flow batteries through double-face architecture and laser-modified and friction-stir processed 3D anode

Aluminum-air batteries (AAB) are regarded as one of the most promising beyond-lithium high-energy-density storage candidates. Here, this paper introduces a three-dimensional (3D) Al 7075 anode enabled by femtosecond laser and friction-stir process which, along with a special double-face anode architecture provides world-class performance. Electrochemical characterizations prove that the corrosion resistance of the modified 3D Al 7075 FSP anode was enhanced, and electrochemically active surface area (ECSA) was increased compared with that of normal Al 7075 anode. Friction-stir processing reduced the mean grain size from 30 μm to 3 μm. The discharge performance of 3D Al 7075 FSP anode is shown to be quite stable, and the average values of energy density are significantly increased from 2256 mWh g –1 to 2941 mWh g –1 at 100 mA cm –2 . In a double-face flowing Al-air battery system, the 3D Al 7075 FSP anode exhibited significantly better electrocatalytic performance (discharge voltage of 0.76 V at 400 mA cm –2 , and power density of 337.8 mW cm –2 ) than that of a commercial Al 7075 anode.

25 ENERGY STORAGE↗
DOE OSTI2021

Extrusion of Unhomogenized Castings of 7075 Aluminum via ShAPE

Extrusion of unhomogenized castings of 7075 aluminum (Al) alloy has been accomplished using shear assisted processing and extrusion (ShAPE). The simultaneous plastic deformation and heat generation during ShAPE rapidly fracture and dissolve interdendritic and intragranular secondary phases of Al-Zn-Mg-Cu, accomplishing homogenization in seconds rather than many hours in a furnace prior to extrusion. ShAPE thereby eliminates the energy-intensive and time-consuming homogenization step required to prepare as-cast microstructures for conventional extrusion. Concurrently, extensive grain refinement occurs due to gradient activation of dynamic recrystallization during ShAPE, which facilitates a threefold increase in extrusion speed compared to the conventional extrusion method. Evident enhancement of the mechanical properties of ShAPE+T6 samples is achieved, compared to the ASTM standard values for conventional extrusion products. The microstructural evolution pathway, involving the processes of grain refinement and secondary particle dissolution, is explained using scanning and transmission electron microscopy.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Surface grain refinement of casting A380 aluminum alloy by ultrasonic-assisted surface mechanical grinding treatment

A novel surface processing technique, ultrasonic-assisted surface mechnical grinding treatment (U-SMGT), was proposed and applied to modify the surface micriostructure of the casting aluminum alloy (A380). Comprehensive post-process chracterization techniques including 3D profilometry, optical microscope, scanning electric microscopy (SEM), and electron backscatter diffraction (EBSD) were carried out to investigate the surface morphology and microstructure of the processed region (PR). It was found that a surface layer of grain refinement with a thickness of about 50 µm was formed. In the as-received base material (BM), large clusters of dendritic eutectic phase with a size of approximately 20 µm were isolated by α-Al matrix. Nano-indentation tests showed that hardness of the eutectic and α-Al in the as-received BM was 2.15 GPa and 1.2 GPa respectively. After U-SMGT, the large dendritic eutectic phase was broken down into much fine particles with an average size of 0.57 µm. These fine particles were uniformly distributed into the α-Al matrix. Nano-indentation measurement exhibited a hardness of 2.27 GPa within the processed region. The overall high hardness in the processed region is a result of the pinning effect of uniformly distributed fine dendrites and grain refinement of Al-matrix.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Epitaxial aluminum layer on antimonide heterostructures for exploring Josephson junction effects

In this study, we present results of our recent work of epitaxially-grown aluminum (epi-Al) on antimonide heterostructures, where the epi-Al thin film is grown at either room temperature or below zero °C. A sharp superconducting transition at T ∼ 1.3 K is observed in these epi-Al films. We further show that supercurrent states are realized in Josephson junctions fabricated in the epi-Al/antimonide heterostructures with mobility μ ∼ 1.0 × 10 6 cm 2 /Vs. These results clearly demonstrate we have achieved growing high-quality epi-Al/antimonide heterostructures, a promising platform for the exploration of Josephson junction effects for quantum information science and microelectronics applications.

Antimonide heterostructures↗
DOE OSTI2023

Strengthening model development and effects of low diffusing solutes to coarsening resistance in aluminum alloys

A modified Orowan strengthening model is proposed to account for finite rod-shaped precipitates with hemispherical caps in aluminum alloy systems. A combined computational and experimental approach is used to study the influences of anisotropic Orowan looping and solute-dislocation interaction on temperature-dependent yield strength. Here, the strengthening model is validated with a dataset containing 297 experimental precipitate geometries, chemistries, temperatures, and strength measurements, and achieves a strong predictive correlation of 0.8713 with experimentally measured yield strengths. Under conditions that are applicable to coarsening, constant particle volume fraction and aspect ratio, the model predicts that short rod precipitates provide far superior strengthening effects compared to plate precipitates. A cast Al-Si-Mg-Cu alloy with rod-shaped Q-phase (Al 3 Cu 2 Mg 9 Si 7 ) precipitates was developed with a novel chemistry exploring the use of low-diffusivity elements (Mn, Ni, V, Zr) to limit precipitate coarsening. The thermodynamic behavior of Mn, Ni, V, and Zr across the Q-phase interface is examined using transmission electron microscopy (TEM), first-principles density-functional theory (DFT) calculations. and atom-probe tomography (APT). DFT calculations utilizing TEM identified Q-phase/Al-matrix interfaces show that Mn, Ni, V, and Zr preferentially segregate to the Q-phase precipitate boundaries which suggests inhibition of precipitate coarsening and higher strengths after temperature exposure. Atom-probe tomography confirms solute atom partitioning/segregation at the Q-phase/Al-matrix interface, found in the modified commercial AS7GU alloy (A356 +0.5%Cu), which supports these observations.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Bayesian automated weighting of aggregated DFT, MD, and experimental data for candidate thermodynamic models of aluminum with uncertainty quantification

Atomic-scale modeling methods such as density functional theory (DFT) and molecular dynamics (MD) can predict the thermodynamic properties of materials at a lower cost than experimental measurements. However, their regular usage in thermodynamic model construction is hampered by the lack of quantitative agreement with experimental measurements and the lack of uncertainty estimates on the data. To make regular usage of this atomistic simulation data, it is important to assess whether the atomistic simulation datasets, by themselves or in combination with experimental measurements, result in the same physics-informed models best supported by experimental measurements alone. Here, models of aluminum thermodynamic properties are discussed using three data sources: atomistic calculations (DFT and MD), experiments, and a combination of atomistic calculations and experiments. The study shows that, after ensuring self-consistency in predicting key invariant points, both experimental measurements and atomistic calculations can significantly contribute to an optimal model.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Commercial aluminum powders, Part I: Particle size characterization and slow heating rate thermal analysis.

We characterized nine commercial aluminum (Al) powders using several methods to measure particle characteristics and thermal analysis, with the goal to understand how these parameters influence energy release. Although it is well-known that lot-to-lot variations in commercial nanoparticles are common, the Al powders were more heterogeneous than anticipated – both with regards to particle size distributions and impurities. Manufacturer specifications – often quoted in the literature without confirmation – were not always accurate for the specific sample lots we investigated. In several cases, different conclusions could be drawn from individual particle size techniques; a combination of multiple techniques provides a clearer picture of the powder properties. Thorough characterization of Al powders is required prior to interpretation of experimental results from a variety of applications. In particular, previous studies have shown contradictory results on the influence of Al on detonation performance, perhaps partially due to insufficient characterization of the Al powders themselves.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Porosity evolution under increasing tension in wire-arc additively manufactured aluminum using in-situ micro-computed tomography and convolutional neural network

Internal defects such as porosities are often formed in additively manufactured metal components. The pores nucleate, grow, and coalesce to form cracks under loads, leading to eventual catastrophic failure. Here, in this paper, the full-field porosity evolution, including pore growth and coalescence in a wire-arc additively manufactured (WAAM) aluminum alloy cylinder under tension is observed with in-situ X-ray micro-computed tomography (μCT). The pore size distribution, density, and tensile stress are calculated from the volumetric images analyzed by a convolutional neural network (CNN) algorithm, which provides rapid analysis of 12,950 slice images from μCT volumetric images at the reference state and 13 tensile strains. The results show the quantitative evolution of the growth and coalescence of macropores under tension. A strong correlation is found between the local pore volume fraction and the true tensile stress when the tensile strain is larger than 5%.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Laser Doppler vibrometry for piezoelectric coefficient ($d_{33}$) measurements in irradiated aluminum nitride

Sensors used for experiments in advanced reactors must survive in harsh environments. Few material systems can be used to construct sensors viable for extreme conditions. Aluminum nitride (AlN) is one such material because it has high thermal stability and radiation resistance and sustains good piezoelectric and dielectric properties at high temperatures. In this work, the piezoelectric coefficient $d_{33}$ of the AlN single-crystal with thermal and irradiation damage was investigated using an indirect method with a laser Doppler vibrometer (LDV). Surface electrodes were deposited on the AlN samples, and the vibration response of the samples to an applied voltage was monitored using the LDV as a function of the excitation frequency. The $d_{33}$ estimation was based on the excitation voltage and the thickness-mode displacement extracted from the LDV measurements. Further, six AlN substrates were irradiated with 8 MeV Al 2+ at three fluences (10 15 , 10 16 , and 10 17 ions/cm 2 ) and two temperatures (300 °C and 500 °C). The $d_{33}$ for the six irradiated samples and one pristine sample were measured, and the measurement uncertainty was estimated based on five repeated tests. All samples were also measured by a commercial piezometer for comparison. The experimental results demonstrate that the piezoelectric coefficients obtained by LDV were about 0.8–1.16 pm/V lower than those obtained by the piezometer. With the compensation of the clamping effect, the corrected LDV values are similar to the piezometer results. Both show similar trends in all samples, which validates the feasibility of the proposed method for $d_{33}$ measurement. Based on the LDV results, the irradiated samples show a 12%–22% decrease in $d_{33}$ compared with the pristine samples. The samples irradiated under the same fluence at a higher temperature (500 °C) demonstrated a lower $d_{33}$ than those at 300 °C. The effect of the retro-reflective tape, sample temperature, and sample size on the $d_{33}$ measurement were also studied.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Understanding the reversible electrodeposition of aluminum in low-cost room-temperature molten salts

Aluminum is the most earth-abundant metal, trivalent, and inert in ambient air; it also has a density approximately five times that of lithium at room temperature, making it attractive for cost-effective, long-duration storage in batteries. Here, we investigate structural requirements and physicochemical and transport properties of ionic liquid (IL) electrolytes thought to enable high reversibility of Al battery anodes. We find that intentionally designed, low-cost IL analogs, including ammonium-based molten salts, offer comparable Al anode reversibility to state-of-the-art imidazolium-based IL melts. A critical ratio of solvated Al-ion species is required to balance the effects of Lewis acidity needed to continuously etch native Al 2 O 3 and form a stable solid electrolyte interphase on Al. Our findings open new opportunities for developing simple, cost-effective, room-temperature Al batteries that enable long-duration electrical energy storage.

25 ENERGY STORAGE↗
DOE OSTI2024

Stress-Alteration Enhancement of the Reactivity of Aluminum Nanoparticles in the Catalytic Decomposition of exo -Tetrahydrodicyclopentadiene (JP-10)

High energy density aluminum nanoparticles (AlNP) upon thermal annealing followed by super-quenching results in elevated stress levels in the metallic core and reduced surface energy at the core-shell interface. Isomer-selective vacuum ultraviolet based photoionization mass spectrometry coupled to a high temperature chemical microreactor reveals that these stress-altered (SA) AlNPs exhibit distinctive temperature-dependent reactivities towards catalytic decomposition of the hydrocarbon jet fuel exo-tetrahydrodicyclopentadiene (JP-10, C 10 H 16 ) compared to untreated (UN) AlNPs. SA-AlNPs show a delayed initiation of the decomposition for JP-10 by 200 K relative to the UN-AlNPs, however, the full decomposition is achieved at 100 K lower temperature. Furthermore, there is less oxygenated products that are generated from the alumina surface-induced heterogeneous oxidation process, and a larger fraction of closed and open-shell hydrocarbons. Furthermore, chemical insight bridging the reactivity order of SA-AlNPs at low and high temperatures, simultaneously, is obtained via a detailed examination of the product branching ratios obtained in this study.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Recent Advances in Rechargeable Aluminum-Ion Batteries and Considerations for Their Future Progress

Owing to their high theoretical capacity and reliable operational safety, nonaqueous rechargeable aluminum batteries (RABs) have emerged as a promising class of battery materials and been intensively studied in recent years; however, a lack of suitable, high-performing positive electrode materials, along with the need for air-sensitive and expensive ionic liquid electrolytes, has significantly hindered the practical use of RABs in large-scale applications. Therefore, we sought to carefully analyze positive electrode materials and the associated electrolytes that have been reported in these battery systems in order to stimulate the design of the next generation of high-performance and low-cost RABs. In this review, we have summarized the electrode materials that have been used in both nonaqueous and aqueous RAB systems and provided a rational classification based on the types of materials used and their respective structures. Additionally, we have reviewed electrolytes employed in RABs and have categorized them according to two main types of applications, either for fixed battery systems or for use in portable devices. Here, a systematic account of recent developments on RABs, with a focus on electrode materials, innovative perspectives, and impending research efforts on future RABs, has been included. Finally, a proposed liquid RAB system is discussed with the aim of solving issues regarding fast-charging and long operational lifetimes, followed by insights into solid RABs for use in both portable and multistructural RAB systems.

25 ENERGY STORAGE↗
DOE OSTI2020

Synergistically Chemical and Thermal Coupling between Graphene Oxide and Graphene Fluoride for Enhancing Aluminum Combustion

Metal combustion reaction is highly exothermic and is used in energetic applications, such as propulsion, pyrotechnics, powering micro- and nano-devices, and nanomaterials synthesis. Aluminum (Al) is attracting great interest in those applications because of its high energy density, earth abundance, and low toxicity. Nevertheless, Al combustion is hard to initiate and progresses slowly and incompletely. On the other hand, ultrathin carbon nanomaterials, such as graphene, graphene oxide (GO), and graphene fluoride (GF), can also undergo exothermic reactions. Herein, we demonstrate that the mixture of GO and GF significantly improves the performance of Al combustion as interactions between GO and GF provide heat and radicals to accelerate Al oxidation. Overall, our experiments and reactive molecular dynamics simulation reveal that GO and GF have strong chemical and thermal couplings through radical reactions and heat released from their oxidation reactions. GO facilitates the dissociation of GF, and GF accelerates the disproportionation and oxidation of GO. When the mixture of GO and GF is added to micron-sized Al particles, their synergistic couplings generate reactive oxidative species, such as CF x and CF x O y , and heat, which greatly accelerates Al combustion. This work demonstrates a new area of using synergistic couplings between ultrathin carbon nanomaterials to accelerate metal combustion and potentially oxidation reactions of other materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Electroprecipitation Mechanism Enabling Silica and Hardness Removal through Aluminum-Based Electrocoagulation

We evaluate the effectiveness of an aluminum-based electrocoagulation pretreatment system to remove dissolved silica and hardness. Silica and hardness limit water recovery during membrane-based desalination applications when silica and hardness exceed the solubility limit and generate scale on the membrane surface. We show that simultaneous removal of nearly all silica (95 ± 4%) and a significant amount of hardness (40–60%) occurs with a hydraulic residence time of 2 h and a charge loading between 0 and 1200 C/L. Increasing the residence time maximized the hardness removal (58 ± 8%) via the formation of larger flocs, which allowed for more constituent removal by gravity settling. We highlight the trade-offs between improved energy efficiency at lower charge loadings and an improved removal rate at a higher charge loading. We further compare the percentage of silica and hardness removed in multicomponent solutions and compare this to single component feed solution. We discuss the implications that operational considerations have in terms of cost and treatment capacity. Finally, a cost–benefit analysis comparing chemical coagulation with electrocoagulation indicates that electrocoagulation could be half the cost of chemical coagulation and could produce more stable effluent pH and conductivity.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Molecular dynamics study of hydrogen Cottrell atmosphere in aluminum: Influence of solute-solute interactions in the dislocation core

Cottrell atmospheres form when solute atoms segregate to dislocations, and is one of the most basic processes by which solutes alter mechanical properties of materials. In the case of hydrogen, Cottrell atmospheres are believed to contribute to hydrogen embrittlement. Here, in this study, we use direct molecular dynamics simulations to study the formation of hydrogen Cottrell atmospheres around edge dislocations in aluminum. Using coarse-graining techniques, we resolve the temporal and spatial evolution of the hydrogen concentration field. By comparing our results with theories of Cottrell atmosphere formation and thermodynamics, we show that a repulsive, concentration-dependent H-H interaction reduces the peak atmosphere concentration at the dislocation core. Furthermore, this interaction differs significantly from the H-H interaction that is experienced in the bulk away from a dislocation.

Aluminum↗
DOE OSTI2020

Ferroelectric C-Axis Textured Aluminum Scandium Nitride Thin Films of 100 nm Thickness

We report on the properties of Aluminum Scandium Nitride (AlScN) thin films deposited by pulsed-DC co-sputtering. We present the impact of the nitrogen-to-argon gas ratio on the crystal growth orientation, film stress, surface roughness, scandium concentration, and deposition rate of 760-860 nm thick AlScN thin films on Ti/Pt (111). We utilize the optimized process conditions from this study to deposit thin layers of AlScN and to explore the nucleation and orientation of thin AlScN layers on Ti/Pt (111). We report on the ferroelectric properties of 100 nm thick AlScN materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗