Search NASA⌕ Search

SEARCH · Search NASA

Results for “ATTITUDE INDICATOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Aerodynamic characteristics of the 140A/B space shuttle orbiter at Mach 10.3

A wind-tunnel investigation was conducted to determine the static longitudinal and lateral-directional characteristics of the 140/B space shuttle orbiter configurations. A 0.010-scale model was tested at angles of attack from 12 deg to 36.5 deg at Reynolds numbers ranging from 0.62 x to 1.33 x based on fuselage reference length. Stability, control, and performance characteristics were obtained for several deflections of the elevons and body flap. Effects of aileron deflection on roll control and longitudinal stability were also measured. The results indicate that the orbiter is neutrally stable at a 20 degs angle of attack with control deflections set at 0 degs and the center of gravity at 65 percent of fuselage length. For a typical entry attitude of 30 degs stable trim resulting in a lift-drag ratio of 1.40 is possible. Increasing the Reynolds number yielded higher values of lift-drag ratio, but only for angles of attack up to 24 degs. The orbiter is directionally unstable with positive dihedral effect. Aileron deflection resulted in adverse yaw to roll control and also caused negative increments in pitching moment over the test angle-of-attack range.

Bernot, P. T.↗
NASA NTRS1980

Flight evaluation of configuration management system concepts during transition to the landing approach for a powered-lift STOL aircraft

Flight experiments were conducted to evaluate two control concepts for configuration management during the transition to landing approach for a powered-lift STOL aircraft. NASA Ames' augmentor wing research aircraft was used in the program. Transitions from nominal level-flight configurations at terminal area pattern speeds were conducted along straight and curved descending flightpaths. Stabilization and command augmentation for attitude and airspeed control were used in conjunction with a three-cue flight director that presented commands for pitch, roll, and throttle controls. A prototype microwave system provided landing guidance. Results of these flight experiments indicate that these configuration management concepts permit the successful performance of transitions and approaches along curved paths by powered-lift STOL aircraft. Flight director guidance was essential to accomplish the task.

Franklin, J. A.↗
NASA NTRS1991

Approximate reasoning-based learning and control for proximity operations and docking in space

A recently proposed hybrid-neutral-network and fuzzy-logic-control architecture is applied to a fuzzy logic controller developed for attitude control of the Space Shuttle. A model using reinforcement learning and learning from past experience for fine-tuning its knowledge base is proposed. Two main components of this approximate reasoning-based intelligent control (ARIC) model - an action-state evaluation network and action selection network are described as well as the Space Shuttle attitude controller. An ARIC model for the controller is presented, and it is noted that the input layer in each network includes three nodes representing the angle error, angle error rate, and bias node. Preliminary results indicate that the controller can hold the pitch rate within its desired deadband and starts to use the jets at about 500 sec in the run.

Berenji, Hamid R.↗
NASA NTRS1953

A Method of Calibrating Airspeed Installations on Airplanes at Transonic and Supersonic Speeds by the Use of Accelerometer and Attitude-Angle Measurements

A method is described for calibrating airspeed installation on airplanes at transonic and supersonic speeds in vertical-plane maneuvers in which use is made of measurements of normal and longitudinal accelerations and attitude angle. In this method all the required instrumentation is carried within the airplane. An analytical study of the effects of various sources of error on the accuracy of an airspeed calibration by the accelerometer method indicated that the required measurements can be made accurately enough to insure a satisfactory calibration.

Zalovick, John A↗
NASA NTRS2016

Options for Staging Orbits in Cis-Lunar Space

NASA has been studying options to conduct missions beyond Low Earth Orbit, but within the Earth‐Moon system, in preparation for deep space exploration including human missions to Mars. Referred to as the Proving Ground, this arena of exploration activities will enable the development of human spaceflight systems and operations to satisfy future exploration objectives beyond the cis‐lunar environment. One option being considered includes the deployment of a habitable element or elements, which could be used as a central location for aggregation of supplies and resources for human missions in cis‐lunar space and beyond. Characterizing candidate orbit locations for this asset and the impacts on system design and mission operations is important in the overall assessment of the options being considered. The orbits described in this paper were initially selected by taking advantage of previous studies conducted by NASA and the work of other authors. In this paper orbits are assessed for their relative attractiveness based on various factors. A set of constraints related to the capability of the combined Orion and SLS system to deliver humans and cargo to and from the orbit are evaluated. Deployed assets intended to spend multiple years in the Proving Ground would ideally require minimal station keeping costs to reduce the mass budget allocated to this function. Additional mission design drivers include eclipse frequency, potential for uninterrupted communication with deployed assets, thermal, attitude control, communications, and other operational implications. Also the ability to support potential lunar surface activities and excursion missions beyond Earth‐Moon space is considered. The results of the characterization and evaluation of the selected orbits indicate a Near Rectilinear Orbit (NRO) is an attractive candidate as an aggregation point or staging location for operations. In this paper, the NRO is further described in terms which balance a number of key attributes that favor a variety of mission classes to meet multiple, sometimes competing, constraints.

Martinez, Roland↗
NASA NTRS1972

Constrained optimal ascent-flyback shuttle trajectories.

An optimal Space Shuttle ascent-flyback trajectory shaping capability is presented which is based on the accelerated gradient parameter optimization technique. A typical atmospheric flight branched optimization problem is analyzed which required the determination of 31 parameters. This parameter set includes the description of the vehicle attitude control angles for three branches of Shuttle flight: first stage ascent, second stage ascent, and first stage flyback. The important in-flight inequality constraints required to maintain the integrity of the vehicle are considered. Results indicate that for a launch into a 55 deg inclined ellipse, a 13% increase in payload can be realized by using optimal control in the first-stage ascent rather than the conventional gravity-turn steering.

Kamm, J. L.↗
NASA NTRS1988

Control Of Flexible Structures-2 (COFS-2) flight control, structure and gimbal system interaction study

The second Control Of Flexible Structures Flight Experiment (COFS-2) includes a long mast as in the first flight experiment, but with the Langley 15-m hoop column antenna attached via a gimbal system to the top of the mast. The mast is to be mounted in the Space Shuttle cargo bay. The servo-driven gimbal system could be used to point the antenna relative to the mast. The dynamic interaction of the Shuttle Orbiter/COFS-2 system with the Orbiter on-orbit Flight Control System (FCS) and the gimbal pointing control system has been studied using analysis and simulation. The Orbiter pointing requirements have been assessed for their impact on allowable free drift time for COFS experiments. Three fixed antenna configurations were investigated. Also simulated was Orbiter attitude control behavior with active vernier jets during antenna slewing. The effect of experiment mast dampers was included. Control system stability and performance and loads on various portions of the COFS-2 structure were investigated. The study indicates possible undesirable interaction between the Orbiter FCS and the flexible, articulated COFS-2 mast/antenna system, even when restricted to vernier reaction jets.

Fay, Stanley↗
NASA NTRS2003

Comparisons of the Impact Responses of a 1/5-Scale Model and a Full-Scale Crashworthy Composite Fuselage Section

A 25-fps vertical drop test of a 1/5-scale model composite fuselage section was conducted to replicate a previous test of a full-scale fuselage section. The purpose of the test was to obtain experimental data characterizing the impact response of the 1/5-scale model fuselage section for comparison with the corresponding full-scale data. This comparison is performed to assess the scaling procedures and to determine if scaling effects are present. For the drop test, the 1/5-scale model fuselage section was configured in a similar manner as the full-scale section, with lead masses attached to the floor through simulated seat rails. Scaled acceleration and velocity responses are compared and a general assessment of structural damage is made. To further quantify the data correlation, comparisons of the average acceleration data are made as a function of floor location and longitudinal position. Also, the percentage differences in the velocity change (area under the acceleration curve) and the velocity change squared (proportional to kinetic energy) are compared as a function of floor location. Finally, correlation coefficients are calculated for corresponding 1/5- and full-scale data channels and these values are plotted versus floor location. From a scaling perspective, the differences between the 1/5- and full-scale tests are relatively small, indicating that appropriate scaling procedures were used in fabricating the test specimens and in conducting the experiments. The small differences in the scaled test data are attributed to minor scaling anomalies in mass, potential energy, and impact attitude.

Jackson, Karen E.↗
NASA NTRS1971

Attitude control of an orbiting space vehicle.

Study of the normal and clamped modes of operation and dynamic response characteristics of the gimbaled control moment gyro (CMG) designed to fulfill the stringent pointing requirements of the Skylab telescope mount when the spacecraft is under the influence of both external and internal torques. The results indicate that the clamped mode of operation provides a feasible approach for significantly improving the system characteristics.

Sutherlin, D. W.↗
NASA NTRS1976

Accident investigation: Analysis of aircraft motions from ATC radar recordings

A technique was developed for deriving time histories of an aircraft's motion from air traffic control (ATC) radar records. This technique uses the radar range and azimuth data, along with the downlinked altitude data (from an onboard Mode-C transponder), to derive an expanded set of data which includes airspeed, lift, thrust-drag, attitude angles (pitch, roll, and heading), etc. This method of analyzing aircraft motions was evaluated through flight experiments which used the CV-990 research aircraft and recordings from both the enroute and terminal ATC radar systems. The results indicate that the values derived from the ATC radar records are for the most part in good agreement with the corresponding values obtained from airborne measurements. In an actual accident, this analysis of ATC radar records can complement the flight-data recorders, now onboard airliners, and provide a source of recorded information for other types of aircraft that are equipped with Mode-C transponders but not with onboard recorders.

Wingrove, R. C.↗
NASA NTRS2003

Light Detection and Ranging-Based Terrain Navigation: A Concept Exploration

This paper discusses the use of Airborne Light Detection And Ranging (LiDAR) equipment for terrain navigation. Airborne LiDAR is a relatively new technology used primarily by the geo-spatial mapping community to produce highly accurate and dense terrain elevation maps. In this paper, the term LiDAR refers to a scanning laser ranger rigidly mounted to an aircraft, as opposed to an integrated sensor system that consists of a scanning laser ranger integrated with Global Positioning System (GPS) and Inertial Measurement Unit (IMU) data. Data from the laser range scanner and IMU will be integrated with a terrain database to estimate the aircraft position and data from the laser range scanner will be integrated with GPS to estimate the aircraft attitude. LiDAR data was collected using NASA Dryden's DC-8 flying laboratory in Reno, NV and was used to test the proposed terrain navigation system. The results of LiDAR-based terrain navigation shown in this paper indicate that airborne LiDAR is a viable technology enabler for fully autonomous aircraft navigation. The navigation performance is highly dependent on the quality of the terrain databases used for positioning and therefore high-resolution (2 m post-spacing) data was used as the terrain reference.

Campbell, Jacob↗
NASA NTRS2009

NASA Tech Briefs, September 2009

opics covered include: Filtering Water by Use of Ultrasonically Vibrated Nanotubes; Computer Code for Nanostructure Simulation; Functionalizing CNTs for Making Epoxy/CNT Composites; Improvements in Production of Single-Walled Carbon Nanotubes; Progress Toward Sequestering Carbon Nanotubes in PmPV; Two-Stage Variable Sample-Rate Conversion System; Estimating Transmitted-Signal Phase Variations for Uplink Array Antennas; Board Saver for Use with Developmental FPGAs; Circuit for Driving Piezoelectric Transducers; Digital Synchronizer without Metastability; Compact, Low-Overhead, MIL-STD-1553B Controller; Parallel-Processing CMOS Circuitry for M-QAM and 8PSK TCM; Differential InP HEMT MMIC Amplifiers Embedded in Waveguides; Improved Aerogel Vacuum Thermal Insulation; Fluoroester Co-Solvents for Low-Temperature Li+ Cells; Using Volcanic Ash to Remove Dissolved Uranium and Lead; High-Efficiency Artificial Photosynthesis Using a Novel Alkaline Membrane Cell; Silicon Wafer-Scale Substrate for Microshutters and Detector Arrays; Micro-Horn Arrays for Ultrasonic Impedance Matching; Improved Controller for a Three-Axis Piezoelectric Stage; Nano-Pervaporation Membrane with Heat Exchanger Generates Medical-Grade Water; Micro-Organ Devices; Nonlinear Thermal Compensators for WGM Resonators; Dynamic Self-Locking of an OEO Containing a VCSEL; Internal Water Vapor Photoacoustic Calibration; Mid-Infrared Reflectance Imaging of Thermal-Barrier Coatings; Improving the Visible and Infrared Contrast Ratio of Microshutter Arrays; Improved Scanners for Microscopic Hyperspectral Imaging; Rate-Compatible LDPC Codes with Linear Minimum Distance; PrimeSupplier Cross-Program Impact Analysis and Supplier Stability Indicator Simulation Model; Integrated Planning for Telepresence With Time Delays; Minimizing Input-to-Output Latency in Virtual Environment; Battery Cell Voltage Sensing and Balancing Using Addressable Transformers; Gaussian and Lognormal Models of Hurricane Gust Factors; Simulation of Attitude and Trajectory Dynamics and Control of Multiple Spacecraft; Integrated Modeling of Spacecraft Touch-and-Go Sampling; Spacecraft Station-Keeping Trajectory and Mission Design Tools; Efficient Model-Based Diagnosis Engine; and DSN Simulator.

Source record↗
NASA NTRS1985

Controller design and parameter identifiability studies for a large space antenna

The problem of control systems synthesis and parameter identifiability are considered for a large, space-based antenna. Two methods are considered for control system synthesis, the first of which uses torque actuators and collocated attitude and rate sensors, and the second method is based on the linear-quadratic-Gaussian (LQG) control theory. The predicted performance obtained by computing variances of pointing, surface and feed misalignment errors in the presence of sensor noise indicates that the LQG-based controller yields superior results. Since controller design requires the knowledge of the system parameters, the identifiability of the structural parameters is investigated by obtaining Cramer-Rao lower bounds. The modal frequencies are found to have the best identifiability, followed by damping ratios, and mode-slopes.

Joshi, S. M.↗
NASA NTRS1987

A piloted simulation of helicopter air combat to investigate effects of variations in selected performance and control response characteristics

A piloted simulation study investigating handling qualities and flight characteristics required for helicopter air to air combat is presented. The Helicopter Air Combat system was used to investigate this role for Army rotorcraft. Experimental variables were the maneuver envelope size (load factor and sideslip), directional axis handling qualities, and pitch and roll control-response type. Over 450 simulated, low altitude, one-on-one engagements were conducted. Results from the experiment indicate that a well damped directional response, low sideforce caused by sideslip, and some effective dihedral are all desirable for weapon system performance, good handling qualities, and low pilot workload. An angular rate command system was favored over the attitude type pitch and roll response for most applications, and an enhanced maneuver envelope size over that of current generation aircraft was found to be advantageous. Pilot technique, background, and experience are additional factors which had a significant effect on performance in the air combat tasks investigated. The implication of these results on design requirements for future helicopters is presented.

Lewis, Michael S.↗
NASA NTRS1961

Predicted Performance of On-Off Systems for Precise Satellite Attitude Control

An investigation has been made of the use of on-off reaction jets for precision attitude control of a satellite. Since a symmetrical vehicle is assumed, only single-axis control needs to be considered. The responses to initial disturbances and also limit-cycle characteristics for several systems have been evaluated. Calculated results indicate that realistic values of settling time and fuel consumption for the example considered can be obtained. The performance of a given system depends on the characteristics of the error detector used. In cases where the detector output was saturated for a relatively low error input, the settling time deteriorated when a lead network was used to provide damping. This deterioration could be eliminated if a separate rate signal to produce vehicle rate limiting were available. As an alternate approach, two systems were investigated which used a timed sequence of torques and could operate with a detector output of very small linear range. Although the performance of these systems was poorer than that of the lead network system without detector saturation, the performance was better than that of the lead network system with low values of detector saturation. The effects on limit-cycle characteristics of hysteresis, lead network constants, dead zone, and thrust time delays were also investigated.

Brown, Stuart C.↗
NASA NTRS1978

A ram-air-spoiler roll stabilization device for forward control cruciform missiles

An experimental investigation has been made at supersonic Mach numbers to determine the feasibility of using a ram-air-spoiler roll control device on a typical canard control missile configuration. As a basis for roll control comparisons, conventional aileron controls on the tail fins were also tested. Results are presented which indicate that the addition of nacelles on the missile tail fins resulted in satisfactory roll control effectiveness and only small changes in basic missile stability. The ram-air-spoiler roll control effectiveness is relatively constant over the range of vehicle attitudes and Mach numbers investigated.

Blair, A. B., Jr.↗
NASA NTRS1980

Improved definition of crustal anomalies for Magsat data

Ongoing efforts to define and model external magnetic field activities are summarized. Data were obtained and plotted for the five international quiet days of each month Magsat was in orbit. The values of the magnetic field at midnight were also plotted for each of the quiet days. Results show that the zero level of the field fluctuates over the time interval considered. Statistical studies were made for the Kp and Ap indices and more sunspot numbers were obtained for the Magsat period. Satellite data are being thinned and reformatted to make them more amenable to testing the Dst and Sq corrections. The software for processing Magsat tapes is being tested with intermediate attitude data.

Source record↗
NASA NTRS1987

A simulator investigation of parameters affecting helicopter handling qualities in air combat (HAC II)

The Helicopter Air Combat system was used to conduct a pilot simulation study investigating the handling qualities and flight characteristics required for helicopter air-to-air combat. Results indicate that a well-damped directional response, low sideforce caused by sideslip, and some effective dihedral are all desirable for weapon system performance, good handling qualities, and low pilot workload. An angular rate command system was favored over the attitude-type pitch and roll response for most applications, and an enhanced maneuver envelope size over that of current generation aircraft was found to be of advantage.

Lewis, Michael S.↗