Search NASA⌕ Search

SEARCH · Search NASA

Results for “Aircraft Modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Full-Span Tiltrotor Aeroacoustic Model (TRAM) Overview and 40- by 80-Foot Wind Tunnel Test

Most helicopter data trends cannot be extrapolated to tiltrotors because blade geometry and aerodynamic behavior, as well as rotor and fuselage interactions, are significantly different for tiltrotors. A tiltrotor model has been developed to investigate the aeromechanics of tiltrotors, to develop a comprehensive database for validating tiltrotor analyses, and to provide a research platform for supporting future tiltrotor designs. The Full-Span Tiltrotor Aeroacoustic Model (FS TRAM) is a dual-rotor, powered aircraft model with extensive instrumentation for measurement of structural and aerodynamic loads. This paper will present the Full-Span TRAM test capabilities and the first set of data obtained during a 40- by 80-Foot Wind Tunnel test conducted in late 2000 at NASA Ames Research Center. The Full-Span TRAM is a quarter-scale representation of the V-22 Osprey aircraft, and a heavily instrumented NASA and U.S. Army wind tunnel test stand. Rotor structural loads are monitored and recorded for safety-of-flight and for information on blade loads and dynamics. Left and right rotor balance and fuselage balance loads are monitored for safety-of-flight and for measurement of vehicle and rotor aerodynamic performance. Static pressure taps on the left wing are used to determine rotor/wing interactional effects and rotor blade dynamic pressures measure blade airloads. All of these measurement capabilities make the FS TRAM test stand a unique and valuable asset for validation of computational codes and to aid in future tiltrotor designs. The Full-Span TRAM was tested in the NASA Ames Research Center 40- by 80-Foot Wind Tunnel from October through December 2000. Rotor and vehicle performance measurements were acquired in addition to wing pressures, rotor acoustics, and Laser Light Sheet (LLS) flow visualization data. Hover, forward flight, and airframe (rotors off) aerodynamic runs were performed. Helicopter-mode data were acquired during angle of attack and thrust sweeps for a variety of tunnel speeds. Wake geometry images were acquired using LLS photographs and suggest dual tip vortex formation at low thrust conditions. The full paper will include comparisons to isolated-rotor TRAM data acquired at the Duits-Nederlandse Windtunnel (DNW) in 1998. The FS TRAM has been established as a valuable national asset for tiltrotor research. Data reduction and analysis of the 40- by 80-Foot Wind Tunnel test results are underway. Follow-on testing of the FS TRAM is currently being planned for the NASA Ames 80- by 120-Foot Wind Tunnel in late 2001.

McCluer, Megan S.↗
NASA NTRS1980

Airborne antenna pattern calculations

A procedure for numerically calculating radiation patterns of fuselage-mounted airborne antennas using the Volumetric Pattern Analysis Program is presented. Special attention is given to aircraft modeling. An actual case study involving a large commercial aircraft is included to illustrate the analysis procedure.

Knerr, T. J.↗
NASA NTRS1985

Experimental study of main rotor tip geometry and tail rotor interactions in hover. Volume 1. Text and figures

A model scale hover test was conducted in the Sikorsky Aircraft Model rotor hover Facility to identify and quantify the impact of the tail rotor on the demonstrated advantages of advanced geometry tip configurations. The test was conducted using the Basic Model Test Rig and two scaled main rotor systems, one representing a 1/5.727 scale UH-60A BLACK HAWK and the others a 1/4.71 scale S-76. Eight alternate rotor tip configurations were tested, 3 on the BLACK HAWK rotor and 6 on the S-76 rotor. Four of these tips were then selected for testing in close proximity to an operating tail rotor (operating in both tractor and pusher modes) to determine if the performance advantages that could be obtained from the use of advanced geometry tips in a main rotor only environment would still exist in the more complex flow field involving a tail rotor. The test showed that overall the tail rotor effects on the advanced tip configurations tested are not substantially different from the effects on conventional tips.

Balch, D. T.↗
NASA NTRS1985

Experimental study of main rotor tip geometry and tail rotor interactions in hover. Volume 2: Run log and tabulated data

A model scale hover test was conducted in the Sikorsky Aircraft Model Rotor hover Facility to identify and quantify the impact of the tail rotor on the demonstrated advantages of advanced geometry tip configurations. The existence of mutual interference between hovering main rotor and a tail rotor was acknowledged in the test. The test was conducted using the Basic Model Test Rig and two scaled main rotor systems, one representing a 1/5.727 scale UH-60A BLACK HAWK and the others a 1/4.71 scale S-76. Eight alternate rotor tip configurations were tested, 3 on the BLACK HAWK rotor and 6 on the S-76 rotor. Four of these tips were then selected for testing in close proximity to an operating tail rotor (operating in both tractor and pusher modes) to determine if the performance advantages that could be obtained from the use of advanced geometry tips in a main rotor only environment would still exist in the more complex flow field involving a tail rotor. This volume contains the test run log and tabulated data.

Balch, D. T.↗
NASA NTRS1991

Model representation in the PANCOR wall interference assessment code

An investigation into the aircraft model description requirements of a wall interference assessment and correction code known as PANCOR was conducted. The accuracy necessary in specifying various elements of the model description were defined. It was found that the specified lift coefficient is the most important model parameter in the wind tunnel simulation. An accurate specification of the model volume was also found to be important. Also developed was a partially automated technique for generating wing lift distributions that are required as input to PANCOR. An existing three dimensional transonic small disturbance code was modified to provide the necessary information. A group of auxiliary computer programs and procedures was developed to help generate the required input for PANCOR.

Al-Saadi, Jassim A.↗
NASA NTRS1985

A.I.-based real-time support for high performance aircraft operations

Artificial intelligence (AI) based software and hardware concepts are applied to the handling system malfunctions during flight tests. A representation of malfunction procedure logic using Boolean normal forms are presented. The representation facilitates the automation of malfunction procedures and provides easy testing for the embedded rules. It also forms a potential basis for a parallel implementation in logic hardware. The extraction of logic control rules, from dynamic simulation and their adaptive revision after partial failure are examined. It uses a simplified 2-dimensional aircraft model with a controller that adaptively extracts control rules for directional thrust that satisfies a navigational goal without exceeding pre-established position and velocity limits. Failure recovery (rule adjusting) is examined after partial actuator failure. While this experiment was performed with primitive aircraft and mission models, it illustrates an important paradigm and provided complexity extrapolations for the proposed extraction of expertise from simulation, as discussed. The use of relaxation and inexact reasoning in expert systems was also investigated.

Vidal, J. J.↗
NASA NTRS2009

A Comparative Study of a 1/4-Scale Gulfstream G550 Aircraft Nose Gear Model

A series of fluid dynamic and aeroacoustic wind tunnel experiments are performed at the University of Florida Aeroacoustic Flow Facility and the NASA-Langley Basic Aerodynamic Research Tunnel Facility on a high-fidelity -scale model of Gulfstream G550 aircraft nose gear. The primary objectives of this study are to obtain a comprehensive aeroacoustic dataset for a nose landing gear and to provide a clearer understanding of landing gear contributions to overall airframe noise of commercial aircraft during landing configurations. Data measurement and analysis consist of mean and fluctuating model surface pressure, noise source localization maps using a large-aperture microphone directional array, and the determination of far field noise level spectra using a linear array of free field microphones. A total of 24 test runs are performed, consisting of four model assembly configurations, each of which is subjected to three test section speeds, in two different test section orientations. The different model assembly configurations vary in complexity from a fully-dressed to a partially-dressed geometry. The two model orientations provide flyover and sideline views from the perspective of a phased acoustic array for noise source localization via beamforming. Results show that the torque arm section of the model exhibits the highest rms pressures for all model configurations, which is also evidenced in the sideline view noise source maps for the partially-dressed model geometries. Analysis of acoustic spectra data from the linear array microphones shows a slight decrease in sound pressure levels at mid to high frequencies for the partially-dressed cavity open model configuration. In addition, far field sound pressure level spectra scale approximately with the 6th power of velocity and do not exhibit traditional Strouhal number scaling behavior.

Khorrami, Mehdi R.↗
NASA NTRS1990

A description and evaluation of TIMER: A time-based terminal flow-control concept

A description of a time-based ATC concept called TIMER (Traffic Intelligence for the Management of Efficient Runway-scheduling) and the results of a fast time and real time computer evaluation are presented. The concept was designed to improve the efficiency of extended terminal area operations (en route approach, transition, and terminal flight to the runway). TIMER integrates en route metering, fuel efficient cruise and profile descents, terminal sequencing and spacing together with computer-generated controller aids, in order to fully use runway capacity and improve efficiency of delay absorption. The concept, by using simplified aircraft models, accommodates both 4-D and non 4-D equipped aircraft and is designed for integration into the manual, voice linked ATC system in an evolutionary manner and still be able to accommodate proposed system upgrade features such as data link and further ground automation. Fast time and real time computer simulation results identify and show the effects and interactions of such key variables as horizon of control, metering fix and final approach delivery time errors, aircraft separation requirements, delay discounting, wind, flight technical error, and knowledge of aircraft final approach speed. The current ATC system has a runway interarrival-error standard deviation of approx. 26 seconds. Simulation results indicate that, with computer aiding, the runway interarrival-error standard deviation for non 4-D equipped traffic can be reduced to the region of 8 to 12 seconds if expected final approach speed is known; however, the reduction is only in the region of 16 to 20 seconds if expected final approach speed is unknown. Another major finding is that en route metering fix delivery-error standard deviation should be kept to less than a number somewhere between 35 to 45 seconds to achieve full runway capacity. This requirement implies the need for either airborne automation or assistance to the controller since the current manual performance in today's en route metering environment is in the order of 1.5 minutes.

Credeur, Leonard↗
NASA NTRS2019

Motion Cueing for Stall Recovery Training in Commercial Transport Simulators

Starting in 2019, airline pilots will be required to perform full stall recovery training in flight simulators. Historically, training simulators weren't required to provide training at conditions outside their normal flight envelope. Post-stall aircraft models are generally required to be implemented to simulate the aircraft response after the stall point. In addition, motion cues need to adequately represent this response to ensure the skills learned in simulator training are directly usable in real flight. This paper provides and overview of six simulator experiments conducted at NASA Ames Research Center to develop a motion cueing strategies for stall recovery training in commercial transport simulators. One of the experiments verified an enhanced motion cueing strategy for stall recovery training on a level-D-certified full flight simulator. This study showed that the enhanced motion results in lower maximum roll angles in the stall maneuver, lower minimum load factors in the recovery, lower numbers of secondary stick shakers in the stall recovery, and a lower maximum airspeed in the recovery. These results indicate that relatively minor enhancements to the motion logic of heritage commercial transport simulators can significantly improve pilot performance in simulated stall recoveries, and potentially improve stall recovery training.

stall recovery↗
NASA NTRS2019

Motion Cueing for Stall Recovery Training in Commercial Transport Simulators

Starting in 2019, airline pilots will be required to perform full stall recovery training in flight simulators. Historically, training simulators weren't required to provide training at conditions outside their normal flight envelope. Post-stall aircraft models are generally required to be implemented to simulate the aircraft response after the stall point. In addition, motion cues need to adequately represent this response to ensure the skills learned in simulator training are directly usable in real flight. This paper provides and overview of six simulator experiments conducted at NASA Ames Research Center to develop a motion cueing strategies for stall recovery training in commercial transport simulators. One of the experiments verified an enhanced motion cueing strategy for stall recovery training on a level-D-certified full flight simulator. This study showed that the enhanced motion results in lower maximum roll angles in the stall maneuver, lower minimum load factors in the recovery, lower numbers of secondary stick shakers in the stall recovery, and a lower maximum airspeed in the recovery. These results indicate that relatively minor enhancements to the motion logic of heritage commercial transport simulators can significantly improve pilot performance in simulated stall recoveries, and potentially improve stall recovery training.

stall recovery↗
NASA NTRS2021

PEM Fuel Cell MODEL for Conceptual Design of Hydrogen eVTOL Aircraft

A model and software for design and analysis of a Proton Exchange Membrane fuel cell (PEMFC) system are developed for hydrogen eVTOL aircraft. Examples are provided of stacks designed for 80 kWe and 500 kWe net electrical power. Examples are provided of eVTOL designed for 250 and 400 lb payload. The trade-offs included stack characteristics, hydrogen storage characteristics, and aircraft payload and range. The objectives were to identify the key technology drivers of a hydrogen rotorcraft, establish technology targets for a viable aircraft, and recommend research to address the fundamental pre-competitive barriers. The current U.S. infrastructure on hydrogen informed the targets and recommendations. The key conclusion is that the advances made in cell electrochemical power density over the last decade might allow a PEMFC system to meet, or even beat, piston engine powered light-utility rotorcraft. The development must focus on the key drivers of a hydrogen eVTOL. The drivers are ultra-light stack cooling and short-term hydrogen storage. A stack system of net electrical power 100−150 kWe with specific power 1.1 kWe/kg including air, cooling, and electrical subsystems, and a tank storage of 15% weight fraction hydrogen are the minimum targets to meet the performance of a modern piston-engine rotorcraft, with a range of 180 nautical miles, payload of 400 lb, and gross weight of about 1400 lb. This is defined as the objective aircraft. If only one target is met, an aircraft of half the range could be produced, with a 30% greater gross take-off weight. This is defined as an intermediate aircraft. Because definitive conclusions are premature without weights and loads data on a flight-worthy stack system, it is recommended that a fuel cell powered hydrogen eVTOL demonstrator be built and flown. The existing hydrogen infrastructure for cars provide ample opportunity to create a pilot program. About 12 metric tons of retail hydrogen are available for cars every day in California, which is less than 0.05% of the yearly hydrogen production in the U.S.. A hypothetical fleet of 100 aircraft, operating 3 flights a day, would increase the demand by 2.25 tons per day and require 140 MWh of renewable electricity for green hydrogen.

PEM↗