Search NASA⌕ Search

SEARCH · Search NASA

Results for “Ballistic Range”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Investigating the relationship between radial pre-stress magnitude and ballistic projectile dwell in heavy confined ceramic targets

A series of bare silicon carbide ceramic armour disks were manufactured with high-strength steel containment to induce varying magnitudes of radial pre-stress. The induced radial stresses, ranging from 0 to 900 MPa, were measured via neutron diffraction and verified by comparison with numerical calculations. Four targets of each configuration, referred to as slip-fit, moderate pre-stress, and high pre-stress, were subject to ballistic testing with hemispherical-nose, tungsten heavy alloy long rod projectiles to determine the interface defeat transition velocity. In-situ diagnostics were unsuccessful in aiding the identification of interface defeat, necessitating a reliance on post-mortem assessment. A transition velocity of approx. 1000 m/s was identified for the unstressed target, increasing to approx. 1200 m/s for the pre-stressed configurations. No performance effect was discernible between the moderate (372 MPa) and high (899 MPa) pre-stress configurations, suggesting that an optimal performance may be achieved for lower pre-stress levels (i.e., <372 MPa). Additionally, the test results were compared with four semi-analytical predictions of interface defeat performance and good agreement was found, albeit with significant range in the model predictions.

42 ENGINEERING↗

Thermal transport properties and some hydrodynamic-like behavior in three-dimensional topological semimetal $\mathrm{ZrTe}_5$

We report hydrodynamic fluidity in condensed matter physics has been experimentally demonstrated only in a limited number of compounds due to the stringent conditions that must be met. Herein, we performed thermal and electrical transport experiments in three-dimensional topological semimetal ZrTe 5 . By measuring the thermal properties in a wide temperature range, two representative experimental evidences of the hydrodynamics are observed in temperature window between the ballistic and diffusive regimes: a faster evolution of the thermal conductivity than in the ballistic regime and the non-monotonic temperature-dependent effective quasiparticle mean-free-path. In addition, magneto-thermal conductivity results indicate that charged quasiparticles, as well as phonons, may also play an important role in this hydrodynamic-like flow in ZrTe 5 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Several preliminary designs for heavy-lift earth-to-orbit transport

Several design concepts are identified for earth-to-orbit delivery of payloads in the 200 Mg range. The concept include winged vehicles which take-off vertically and land horizontally and ballistic shapes similar to the Gemini or Mercury vehicles which take-off and land vertically. Major technology issues include stability problems for the winged vehicle with large base mounted engines and heat shield design problems for the ballistic vehicle, the latter requiring doors in the heat shield for the main engines.

Brien, E. P.↗

Landsat at 45: How it Changed the Way We See the Earth

On October 24, 1946, more than 10 years before the launch of the first artificial satellite Sputnik, scientists at the White Sands Missile Range in New Mexico placed a camera on top of a captured German V-2 ballistic missile. As the rocket flew to an altitude of about 65 miles - just above the generally recognized border of outer space - the 35-millimeter motion picture camera snapped a frame every one and a half seconds. Minutes later, the missile came crashing back down and slammed into the ground at more than 340 mph, but the film survived and gave us our first glimpse of Earth from space. Earth Resources Technology Satellite aka Landsat It was images like those first grainy black and white pictures and later those taken by America's first astronauts in the 1960's that inspired the development of the Earth Resources Technology Satellite (ERTS). From the unique vantage point of space, we could now observe Earth using a variety of different instruments to monitor changes over time. The ERTS-1 satellite, wisely renamed Landsat-1, was launched aboard a Delta rocket on July 23, 1972, into a Sun-synchronous polar orbit at an altitude of about 560 miles. In this unique orbit, Landsat could observe the same point on the Earth every 18 days, always with the same solar illumination, allowing for precise monitoring of changes on the ground over time. Landsat-1, derived from the highly successful Nimbus weather satellites, carried two instruments that allowed it to take images not only in visible light but also in infrared, well-suited to track changes in vegetation over time. Designed to last only one year, Landsat-1 actually operated for nearly three years, by which time it had been joined in space by Landsat-2, a near identical copy of the original. Since then, ever more sophisticated instruments were flown aboard Landsat-3 through -8, with Landsat-9 planned for launch in 2020, acquiring millions of images of Earth over more than four decades. At first, images from Landsat were processed by NASA and hardcopies sold to users for a fee, a somewhat tedious process. Since 2008, images have been made available to all interested users by the US Geological Survey (USGS) at no cost via the Internet in near real time. So, how can Landsat help? In short, Landsat looks. And looks. And proves Yogi right. Space-based images from Landsat and other similar satellites offer a unique and critical capability to observe land use over time by providing repetitive observations of the Earth otherwise unavailable. The data provided by the images can be used by scientists and politicians to inform wise decisions in areas such as agriculture, climate, ecosystems and biodiversity, energy, forest management, human health, fire, natural disasters, urban growth and water management. This overview article doesn't allow for examples from each of these disciplines, but details can be found at the following website: https://landsat.gsfc.nasa.gov/how_landsat_helps/. One third of the US economy is influenced by climate, weather and natural hazards, providing strong economic incentives to sustain a healthy space-based Earth observation program. One example, however, may be illustrative of how Landsat and other space-based observations can be helpful in monitoring and documenting some effects of global climate change. It had been noted since the 1970's that permafrost in subarctic areas like Siberia was melting at an accelerating rate. It also became apparent that this led to the formation of hundreds of melt lakes and the liberation of large quantities of methane, a gas that in the short-term has more potent greenhouse effects than carbon dioxide. The methane turned the water in these lakes blue, making them easy to track over time by satellite. Additionally, the newly released methane has been carbon dated to tens of thousands of years ago, meaning that it had remained frozen since the last Ice Age and therefore hadn't been accounted for in models of the Earth's overall carbon balance. Release of sufficient methane by an increasingly warming climate could actually cause a positive feedback loop in global warming, melting more permafrost and releasing yet more methane. Further monitoring by Landsat and other platforms will reveal whether this process is reversible or whether we've passed the tipping point. In addition to the highly successful Landsat series of satellites, NASA and other agencies such as the National Oceanic and Atmospheric Administration (NOAA) operate a fleet of other Earth observing platforms, many with more specific research goals such as monitoring sea ice levels or atmospheric carbon content. Several instruments aboard the International Space Station also contribute to this overall effort to better understand short- and long-term changes to the Earth. Many of these missions are guided by the 2009 Decadal Survey published by the National Research Council of the National Academy of Sciences. Europe, Russia and China all see the value of space-based Earth observation by deploying their own fleet of satellites.

Uri, John↗

Mechanoresponsive Healing Polymers

Methods are provided to produce new mechanoresponsive healing systems. Additionally, various embodiments provide a two tier self-healing material system concept that provides a non-intrusive method to mitigate impact damage in a structure ranging from low velocity impact damage (e.g., crack damage) to high velocity impact damage (e.g., ballistic damage.) The various embodiments provide the mechanophore linked polymer PBG-BCB-PBG. The various embodiments provide methods for synthesizing PBG-BCB-PBG.

Gordon, Keith L.↗

Ballistic limit regression analysis for Space Station Freedom meteoroid and space debris protection system

Relationships defining the ballistic limit of Space Station Freedom's (SSF) dual wall protection systems have been determined. These functions were regressed from empirical data found in Marshall Space Flight Center's (MSFC) Hypervelocity Impact Testing Summary (HITS) for the velocity range between three and seven kilometers per second. A stepwise linear least squares regression was used to determine the coefficients of several expressions that define a ballistic limit surface. Using statistical significance indicators and graphical comparisons to other limit curves, a final set of expressions is recommended for potential use in Probability of No Critical Flaw (PNCF) calculations for Space Station. The three equations listed below represent the mean curves for normal, 45 degree, and 65 degree obliquity ballistic limits, respectively, for a dual wall protection system consisting of a thin 6061-T6 aluminum bumper spaced 4.0 inches from a .125 inches thick 2219-T87 rear wall with multiple layer thermal insulation installed between the two walls. Normal obliquity is d(sub c) = 1.0514 v(exp 0.2983 t(sub 1)(exp 0.5228). Forty-five degree obliquity is d(sub c) = 0.8591 v(exp 0.0428) t(sub 1)(exp 0.2063). Sixty-five degree obliquity is d(sub c) = 0.2824 v(exp 0.1986) t(sub 1)(exp -0.3874). Plots of these curves are provided. A sensitivity study on the effects of using these new equations in the probability of no critical flaw analysis indicated a negligible increase in the performance of the dual wall protection system for SSF over the current baseline. The magnitude of the increase was 0.17 percent over 25 years on the MB-7 configuration run with the Bumper II program code.

Jolly, William H.↗

Longitudinal Aerodynamic Characteristics and Effect of Rocket Jet on Drag of Models of the Hermes A-3A and A-3B Missiles in Free Flight at Mach Numbers From 0.6 to 2.0

A free-flight investigation over a Mach number range from 0.6 to 2.0 has been conducted to determine the longitudinal aerodynamic characteristics and effect of rocket jet on zero-lift drag of 1/5-scale models of two ballistic-type missiles, the Hermes A-3A and A-3B. Models of both types of missiles exhibited very nearly linear normal forces and pitching moments over the angle-of-attack range of 8 deg to -4 deg and Mach number range tested. The centers of pressure for both missiles were not appreciably affected by Mach number over the subsonic range; however, between a Mach number of 1.02 and 1.50 the center of pressure for the A-3A model moved forward 0.34 caliber with increasing Mach number. At a trim angle-of-attack of approximately 30 deg, the A-3A model indicated a total drag coefficient 30% higher than the power-off zero-lift drag over the subsonic Mach number range and 10% higher over the supersonic range. Under the conditions of the present test, and excluding the effect of the jet on base drag, there was no indicated effect of the propulsive jet on the total drag of the A-3A model. The propulsive jet operating at a jet pressure ratio p(sub j)/p(sub o) of 0.8 caused approximately 100% increase in base drag over the Mach number range M = 0.6 to 1.0. This increase in base drag amounts to 15% of the total drag. An underexpanded jet operating at jet pressure ratios corresponding approximately to those of the full-scale missile caused a 22% reduction in base drag at M = 1.55 (p(sub j)/p(sub o) = 1.76) but indicated no change at M = 1.30 (p(sub j)/p(sub o) = 1.43). At M = 1.1 and p(sub j)/p(sub o) = 1.55, the jet caused a 50% increase in base drag.

Jackson, H. Herbert↗

Longitudinal dynamic stability of a shuttle vehicle.

Analytical study of the longitudinal dynamic stability of a nonrolling, lifting vehicle gliding at hypersonic speeds. The analysis applies to shuttle vehicles designed for operating up to the rim of a planetary atmosphere. A general nondimensional time transformation is introduced to derive a unified second-order linear differential equation for the angle of attack, valid for all types of reentry of a general type of vehicle. The stability of motion is discussed for two fundamental regimes of flight that are based on widely different assumptions. For near ballistic entry along a straight line trajectory, the equation reduces to a confluent hypergeometric equation, the solution of which can be expressed in terms of Whittaker's function. Using a theorem in the theory of stability of differential equations, criteria for damped oscillations are derived. It is shown that the aerodynamic criteria for stability are the same as for the case of ballistic entry. In addition, for each vehicle configuration, and specified planetary atmosphere, there exists an altitude range where the angle of attack frequency is nearly equal to the orbital frequency causing instability in pitch. This resonance instability is due to the ellipticity of the orbit. Criteria for eccentricity instability are derived.

Vinh, N. X.↗

Longitudinal control effectiveness and entry dynamics of a single-stage-to-orbit vehicle

The classical theory of flight dynamics for airplane longitudinal stability and control analysis was extended to the case of a hypervelocity reentry vehicle. This includes the elements inherent in supersonic and hypersonic flight such as the influence of the Mach number on aerodynamic characteristics, and the effect of the reaction control system and aerodynamic controls on the trim condition through a wide range of speed. Phugoid motion and angle of attack oscillation for typical cases of cruising flight, ballistic entry, and glide entry are investigated. In each case, closed form solutions for the variations in altitude, flight path angle, speed and angle of attack are obtained. The solutions explicitly display the influence of different regions design parameters and trajectory variables on the stability of the motion.

Vinh, N. X.↗

Solution of the Angles-Only Satellite Tracking Problem

A single observation station, located at an arbitrary point on the surface of the Earth, can determine only the azimuth and elevation angles of a satellite or ballistic vehicle, and the time at which these observations occur. No information is available about the range or the range-rate of the target. It is shown that five observations of either the elevation or the azimuth, and the time of either set of observations, determine the complete set of orbital elements of the target. The implementation of the theory presented here could provide a great reduction in the hardware costs associated with satellite and reentry vehicle tracking.

Burnes, R. E.↗

Lunar Return Reentry Thermal Analysis of a Generic Crew Exploration Vehicle Wall Structures

Thermostructural analysis was performed on generic crew exploration vehicle (GCEV) heat shielded wall structures subjected to reentry heating rates based on five potential lunar return reentry trajectories. The GCEV windward outer wall is fabricated with a graphite/epoxy composite honeycomb sandwich panel and the inner wall with an aluminum honeycomb sandwich panel. The outer wall is protected with an ablative Avcoat-5026-39H/CG thermal protection system (TPS). A virtual ablation method (a graphical approximation) developed earlier was further extended, and was used to estimate the ablation periods, ablation heat loads, and the TPS recession layer depths. It was found that up to 83 95 percent of the total reentry heat load was dissipated in the TPS ablation process, leaving a small amount (3-15 percent) of the remaining total reentry heat load to heat the virgin TPS and maintain the TPS surface at the ablation temperature, 1,200 F. The GCEV stagnation point TPS recession layer depths were estimated to be in the range of 0.280-0.910 in, and the allowable minimum stagnation point TPS thicknesses that could maintain the substructural composite sandwich wall at the limit temperature of 300 F were found to be in the range of 0.767-1.538 in. Based on results from the present analyses, the lunar return abort ballistic reentry was found to be quite attractive because it required less TPS weight than the lunar return direct, the lunar return skipping, or the low Earth orbit guided reentry, and only 11.6 percent more TPS weight than the low Earth orbit ballistic reentry that will encounter a considerable weight penalty to obtain the Earth orbit. The analysis also showed that the TPS weight required for the lunar return skipping reentry was much more than the TPS weight necessary for any of the other reentry trajectories considered.

Ko, William L.↗

Tracking Seismic Velocity Perturbations at Ridgecrest Using Ballistic Correlation Functions

Abstract We present results based on data of a dense nodal array composed of 147 stations, deployed in 2022 near the epicenter of the 2019 Mw 7.1 Ridgecrest earthquake to investigate characteristics of the seismic wavefields. Through array analyses, we identified two primary components. First, we observed far-field P waves dominating the 0.5–1.2 Hz frequency range, which are likely primarily generated by wind-driven oceanic swell activity. Second, we detected near-field body waves resulting from anthropogenic activities in the frequency range 2–8 Hz. We examined noise correlation functions derived from data of the dense deployment and regional stations to explore fault-zone seismic velocity changes using ballistic arrivals, with a focus on velocity perturbation shortly before and after the Ridgecrest earthquake sequence. Our findings exhibit distinct behavior compared to results obtained through standard coda-wave interferometry. Particularly, we observed a decrease in P-wave travel time on certain station pairs prior to the 2019 earthquake sequence. Supported by detailed investigation of the local seismic wavefields, we interpret the decreasing P-wave travel time as likely caused by a velocity increase away from the fault, possibly related to fluid migration. However, additional information is necessary to verify this hypothesis.

Geochemistry & Geophysics↗

External control of the Saturn kilometric radiation by the solar wind - Comparison between Voyager 1 and 2 observations

The long-term modulation of Saturn's nonthermal radio emission in the kilometric wavelength range has been studied based upon data obtained by Voyagers 1 and 2. A comparison of the ballistic and hydrodynamic propagation of solar wind features from the spacecraft to Saturn allows the uncertainty inherent in the projection to be determined. The results confirm the previous suggestion that momentum, ram pressure, and kinetic energy flux are the primary solar wind parameters that drive the nonthermal radio emission. It is suggested that, under certain conditions and for limited periods of time, the magnetic properties and time derivatives of the solar wind have increased importance.

Rucker, H. O.↗

Video camera system for locating bullet holes in targets at a ballistics tunnel

A system consisting of a single charge coupled device (CCD) video camera, computer controlled video digitizer, and software to automate the measurement was developed to measure the location of bullet holes in targets at the International Shooters Development Fund (ISDF)/NASA Ballistics Tunnel. The camera/digitizer system is a crucial component of a highly instrumented indoor 50 meter rifle range which is being constructed to support development of wind resistant, ultra match ammunition. The system was designed to take data rapidly (10 sec between shoots) and automatically with little operator intervention. The system description, measurement concept, and procedure are presented along with laboratory tests of repeatability and bias error. The long term (1 hour) repeatability of the system was found to be 4 microns (one standard deviation) at the target and the bias error was found to be less than 50 microns. An analysis of potential errors and a technique for calibration of the system are presented.

Burner, A. W.↗

Combined Structural and Trajectory Control of Variable-Geometry Planetary Entry Systems

Some of the key challenges of planetary entry are to dissipate the large kinetic energy of the entry vehicle and to land with precision. Past missions to Mars were based on unguided entry, where entry vehicles carried payloads of less than 0.6 T and landed within 100 km of the designated target. The Mars Science Laboratory (MSL) is expected to carry a mass of almost 1 T to within 20 km of the target site. Guided lifting entry is needed to meet these higher deceleration and targeting demands. If the aerodynamic characteristics of the decelerator are variable during flight, more trajectory options are possible, and can be tailored to specific mission requirements. In addition to the entry trajectory modulation, having variable aerodynamic properties will also favor maneuvering of the vehicle prior to descent. For proper supersonic parachute deployment, the vehicle needs to turn to a lower angle of attack. One approach to entry trajectory improvement and angle of attack control is to embed a variable geometry decelerator in the design of the vehicle. Variation in geometry enables the vehicle to adjust its aerodynamic performance continuously without additional fuel cost because only electric power is needed for actuating the mechanisms that control the shape change. Novel structural and control concepts have been developed that enable the decelerator to undergo variation in geometry. Changing the aerodynamic characteristics of a flight vehicle by active means can potentially provide a mechanically simple, affordable, and enabling solution for entry, descent, and landing across a wide range of mission types, sample capture and return, and reentry to Earth, Titan, Venus, or Mars. Unguided ballistic entry is not sufficient to meet this more stringent deceleration, heating, and targeting demands. Two structural concepts for implementing the cone angle variation, a segmented shell, and a corrugated shell, have been presented.

Quadrelli, Marco B.↗

HVI Ballistic Limit Characterization of Fused Silica Thermal Panes

Fused silica window systems are used heavily on crewed reentry vehicles, and they are currently being used on the next generation of US crewed spacecraft, Orion. These systems improve crew situational awareness and comfort, as well as, insulating the reentry critical components of a spacecraft against the intense thermal environments of atmospheric reentry. Additionally, these materials are highly exposed to space environment hazards like solid particle impacts. This paper discusses impact studies up to 10 km/s on a fused silica window system proposed for the Orion spacecraft. A ballistic limit equation that describes the threshold of perforation of a fuse silica pane over a broad range of impact velocities, obliquities and projectile materials is discussed here.

Miller, J. E.↗

Supersonic Retropropulsion on Robotic Mars Landers: Selected Design Trades

Many concepts for future robotic Mars lander missions require landing heavier payloads than those landed to date. Mars lander architectures to date have relied on a parachute to help slow the lander; however the effectiveness of a parachute in the thin Martian atmosphere is diminished with heavier payloads unless the diameter of the parachute is increased or it is deployed at a higher Mach number, both of which are significant technical challenges. In addition the parachute can be successfully deployed only within a specific Mach number and dynamic pressure range. Targeting the entry trajectory to hit this “Mach-Q box” imposes constraints on the entry ballistic coefficient, limiting it to ~ 150-200 kg/m^2. Eliminating the parachute from the design requires descent engine ignition at supersonic speeds (Supersonic Retropropulsion, or SRP). SRP increases the propellant requirement, but also allows entry ballistic coefficients of ~600 kg/m^2 or more, with the consequence of significantly increased entry mass and landed payload mass.

Lorenz, Christopher G.↗

A Fixed-Base-Simulator Study of the Ability of a Pilot to Establish Close Orbits Around the Moon

A study was made on a six-degree-of-freedom fixed-base simulator of the ability of human pilots to modify ballistic trajectories of a 5 space vehicle approaching the moon to establish a circular orbit about 50 miles above the lunar surface. The unmodified ballistic trajectories had miss distances from the lunar surface of from 40 to 80 miles, and a velocity range of from 8,200 to 8,700 feet per second at closest approach. The pilot was given control of the thrust (along the vehicle longitudinal axis) and torques about all three body axes. The information display given to the pilot was a hodograph of the vehicle rate of descent and circumferential velocity, an altimeter, and vehicle attitude and rate meters.

Queijo, M. J.↗