Search NASA⌕ Search

SEARCH · Search NASA

Results for “CADMIUM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Multi-channel front-end ASIC for a 3D position-sensitive detector

Arrays of 3D position-sensitive detectors (3DPSD), operating at room temperature and using cadmium zinc telluride (CZT) and thallium bromide (TIBr) sensors, are suitable for gamma-ray spectrometry in many applications. One detector configuration, the 3D position-sensitive Virtual Frisch-Grid detector (VFG), is particularly advantageous for integrating into large area arrays. The signals generated inside each detector of the array are captured with the anode, cathode and four pads that enable the reconstruction of the position and energy of the ionizing interaction by measurements of amplitude and timing of the signals. For these applications, a low-noise front-end ASIC has been developed, capable of processing bipolar signals (needed because of AC-coupling of certain electrodes). The ASIC can be coupled to an ADC in order to form a compound “waveform digitizer” capable of post-processing the analog signals and determining amplitude and timing information. This paper describes a 32-channel front-end ASIC that is suitable for reading out a 3 × 3 or 4 × 4 element matrix in the VFG configuration. Each channel is composed of a low-noise charge amplifier with an adaptive continuous reset feedback circuit suitable for both positive and negative charge, a first order shaper and a single-to-differential converter output stage. Voltage and current references are all internally generated by 10-bit DACs and the chip is fully controllable with the I 2 C communication protocol. The readout channel response has been verified using the implemented injection circuit. Linear behavior up to ~75 ke ± with the gain of ~80 mV/fC, and up to ~200 ke ± with the gain of ~30 mV/fC was demonstrated. In conclusion, the first test result waveforms using a 137 Cs radioactive source on a 5 × 5 × 12 mm 3 TIBr crystal are reported.

47 OTHER INSTRUMENTATION↗
DOE OSTI2026

Resilience of High-Efficiency CdSeTe:As and CdSeTe:Cu Solar Cells to Proton Irradiation

Power generation in space is currently dominated by expensive III-V multi-junction photovoltaic (PV) devices and cheap crystalline silicon (c-Si) PV devices. Both of these technologies degrade rapidly in proton-radiation-rich space environments, such as the Van Allen belt. The present study of cadmium selenide telluride- (CdSeTe-) based PV devices exposed to 150-to-1500 keV proton irradiation with fluences up to 9 x 1013 cm-2 reveal a more radiation-hard alternative to III-V and c-Si PV technologies. We report on measurement and analysis of current density vs voltage (JV), external quantum efficiency (EQE), external radiative efficiency, and capacitance vs voltage (CV) characteristics. JV characteristics of As-doped CdSeTe devices show 80% remaining power conversion efficiency (PCE) relative to unexposed controls when exposed to 650 keV protons at a fluence of 1012 cm-2. Under these same irradiation conditions, Cu-doped CdSeTe devices demonstrate an even better 95% PCE retention compared with unirradiated control devices. Evidence of radiation-induced absorber p-type doping compensation is observed in the glass-side EQE at 0 V and CV characteristics of most of the irradiated CdSeTe:As devices, but clear compensation is evident only for the most heavily irradiated CdSeTe:Cu devices. Elevated blue-green photocurrent in the film-side 0 V EQE suggests a buried junction in the most heavily irradiated CdSeTe:As devices. Although CdSeTe:Cu devices are the more resilient of the CdSeTe structures, both CdSeTe-based technologies are radiation-hard when compared to c-Si and III-V multi-junction PV.

14 SOLAR ENERGY↗
DOE OSTI2021

Neutron-Resonance Transmission Analysis with a Compact Deuterium-Tritium Neutron Generator

Neutron Resonance Transmission Analysis (NRTA) is a spectroscopic technique which uses the resonant absorption of neutrons in the epithermal range to infer the isotopic composition of an object. This spectroscopic technique has relevance in many traditional fields of science and nuclear security. NRTA in the past made use of large, expensive accelerator facilities to achieve precise neutron beams, significantly limiting its applicability. Here, we describe a series of NRTA experiments where we use a compact, low-cost deuterium-tritium (DT) neutron generator to produce short neutron beams (2.6 m) along with a 6 Li-glass neutron detector. The time-of-flight spectral data from five elements – silver, cadmium, tungsten, indium, and 238 U – clearly show the corresponding absorption lines in the 1-30 eV range. The experiments show the applicability of NRTA in this simplified configuration, and prove the feasibility of this compact and low-cost approach. This could significantly broaden the applicability of NRTA, and make it practical and applicable in many fields, such as material science, nuclear engineering, and arms control.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Charge Transport and Space-Charge Formation in Cd 1 - x Zn x Te 1 - y Se y Radiation Detectors

The electron- and hole-transport properties in cadmium zinc telluride selenide (CZTS) crystals are studied using a laser-induced transient-current technique with pulsed and dc bias. The internal electric field profile and velocity of surface recombination are determined by Monte Carlo simulations of electron and hole transient currents combined with a numerical solution of the drift-diffusion equation coupled with Poisson’s equation. Electron and hole drift mobilities of μe = 830 cm 2 /Vs and μh = 40 cm 2 /Vs, respectively, are determined. We also develop a simple technique for evaluating surface recombination directly from measured current waveforms without the need for numerical simulation. The good quality of the prepared detector at pulsed bias, with electron- and hole-mobility-lifetime products of (μτ)e = 1.9 × 10 -3 cm 2 /V and (μτ)h = 1.4 × 10 -4 cm 2 /V, respectively, are observed. The formation of a positive space charge, originating from hole injection combined with a recombination level, is found. We observe a significant position dependence of the lifetime of electrons and holes in dc bias due to hole injection. The experiment is successfully fitted by a simple model dominated by a single deep recombination level with an energy of E t =E C -0.73eV; concentration of 7.3 × 10 11 cm -3 ; and electron- and hole-capture cross sections of 3.5 × 10 -14 cm 2 and 6.5 × 10 -14 cm 2 , respectively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Light-Induced Decoupling of Electronic and Magnetic Properties in Manganites

The strongly correlated material La 0.7 ⁢Sr 0.3 ⁢Mn⁢O 3 (LSMO) exhibits metal-to-insulator and magnetic transition near room temperature. Although the physical properties of LSMO can be manipulated by strain, chemical doping, temperature, or magnetic field, they often require large external stimuli. Further, to include additional flexibility and tunability, we developed a hybrid optoelectronic heterostructure that uses photocarrier injection from cadmium sulfide (Cd⁢ S) to an LSMO layer to change its electrical conductivity. LSMO exhibits no significant optical response; however, the Cd ⁢S/LSMO heterostructures show an enhanced conductivity, with a resistance drop of about 37%, at the transition temperature under light stimuli. This enhanced conductivity in response to light is comparable to the effect of a 9 T magnetic field in pure LSMO. Surprisingly, the optical and magnetic responses of Cd⁢ S/LSMO heterostructures are decoupled and exhibit different effects when both stimuli are applied. This unexpected behavior shows that heterostructuring strongly correlated oxides may require a new understanding of the coupling of physical properties across the transitions and provide the means to implement new functionalities.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Direct link between disorder and magnetoresistance in topological semimetals

The extent to which disorder influences the properties of topological semimetals is relevant to the understanding of topological states and their use in practical applications. Using molecular beam epitaxy, we achieve systematic control of point defect concentrations in the prototypical Dirac semimetal Cd 3 As 2 to gain insight into the role of disorder on electron transport behavior. Using the guiding center diffusion model for linear magnetoresistance, we extract point defect densities as a function of deposition conditions. We find that reducing cadmium defect concentrations by an order of magnitude results in an 2x increase in the magnetoresistance from 450% to 900%. This finding yields important information in the quest to identify the origin of linear magnetoresistance in a wider range of materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Coupling strongly correlated electron systems to a tunable electronic reservoir

Here, we study the effect of coupling an electronic reservoir to a Hubbard model and to a dimer Hubbard model. This is motivated by recent experiments on the effect of illumination on the insulator-metal transition in a vanadium oxides and photoconductive cadmium sulfide heterostructure. We model the system as an electronic reservoir hybridized to the correlated system. We assume that the light intensity controls the hybridization coupling strength. We find that the light intensity acts similarly as the temperature in the weak interaction regime. This is consistent with the role played by electronic reservoirs in out-of-equilibrium systems. In contrast, qualitative differences appear at strong coupling. We show that modeling the V 2 ⁢O 3 compound with a Hubbard model, our results describe qualitatively well the observed illumination-driven suppression of the insulator-metal transition. In contrast, in the DHM results fail to capture the mild suppression observed in the case of VO 2 . This indicates that the lattice may play an important role in this case.

Materials Science↗
DOE OSTI2024

Improved limits on n → n ' transformation from the Spallation Neutron Source

Conversions between neutrons n and dark matter candidate sterile neutrons n' have been proposed as a mechanism for baryon number $\mathscr{B}$ violation. In the case that there is a small mass difference Δ⁢m between the n and the n' states, oscillations can be induced by compensating for Δ⁢m with a magnetic field. A search for such neutron oscillations was performed at the Spallation Neutron Source by looking for anomalous neutron transmission through a strongly absorbing cadmium wafer inside of a 6.6 T magnet. The approach described here saw no regenerated neutrons above background, which provides an improved limit for neutron–sterile neutron transformations for a range of Δ⁢m between 0.1 and 1000 neV.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Stimulated Rayleigh Scattering Enhanced by a Longitudinal Plasma Mode in a Periodically Driven Dirac Semimetal Cd 3 As 2

Using broadband (12–45 THz) multi-terahertz spectroscopy, we show that stimulated Rayleigh scattering dominates the transient optical conductivity of cadmium arsenide, a Dirac semimetal, under an optical driving field at 30 THz. Here, the characteristic dispersive line shape with net optical gain is accounted for by optical transitions between light-induced Floquet subbands, strikingly enhanced by the longitudinal plasma mode. Stimulated Rayleigh scattering with an unprecedentedly large refractive index change may pave the way for slow light generation in conductive solids at room temperature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Top-Performing Photovoltaic Cells Compared to the Shockley–Queisser Limit

Top-performing single-junction and two-terminal tandem devices that include at least one polycrystalline cell are compared with each other and their ideal limits. The parameters of open-circuit voltage, short-circuit current, and fill-factor are individually compared to the Shockley–Queisser limit to investigate where different technologies have room to improve. Technologies, such as silicon and cadmium telluride have the most room for improvement in open-circuit voltage currently utilizing 87% and 81% of their maxima, respectively. Detailed diode and fill-factor loss analysis is presented for single-junction devices to give further insight on how they compare and where efficiency is lost. Single-crystal technologies demonstrate a fill-factor closer to the Shockley–Queisser limit than polycrystalline devices. The high diode quality factor of polycrystalline devices is the leading cause of the decreased fill-factor. Similar analysis on tandem cells with at least one thin-film cell shows that although their efficiency exceeds that of the single-junction cells, the fraction of their ideal efficiency is smaller. Here, by comparing parameters to the Shockley–Queisser limit, it becomes clearer where certain technologies have the potential for improvement.

High efficiency↗
DOE OSTI2020

Doping of CdTe Using CuCl2 Solution for Highly Efficient Photovoltaic Devices

Here, we report doping of cadmium telluride (CdTe) thin film solar cells using copper (II) chloride (CuCl 2 ) solution in deionized water. The CdTe thin films were immersed in 0.1 mmol CuCl 2 solution in water and annealed in the temperature range of 180-240 degrees C for various time durations. The devices were completed using thermally evaporated gold (Au) and measured under simulated AM1.5G spectrum. The average device efficiency of CuCl 2 treated CdTe devices increased to 13.7 % (best cell reaching 14.0%) with significant improvement on open-circuit voltage (VOC ) as compared with 12.4% (best cell 12.7%) for thermally evaporated Cu doped CdTe devices. For CuCl 2 treated CdTe devices, we found higher photoluminescence (PL) intensity and longer carrier life time at room temperature indicating solution based doping offers better control of Cu doping density as compared with evaporated Cu.

14 SOLAR ENERGY↗
DOE OSTI2023

A composite electrodynamic mechanism to reconcile spatiotemporally resolved exciton transport in quantum dot superlattices

Quantum dot (QD) solids are promising optoelectronic materials; further advancing their device functionality requires understanding their energy transport mechanisms. The commonly invoked near-field Förster resonance energy transfer (FRET) theory often underestimates the exciton hopping rate in QD solids, yet no consensus exists on the underlying cause. In response, we use time-resolved ultrafast stimulated emission depletion (STED) microscopy, an ultrafast transformation of STED to spatiotemporally resolve exciton diffusion in tellurium-doped cadmium selenide–core/cadmium sulfide–shell QD superlattices. We measure the concomitant time-resolved exciton energy decay due to excitons sampling a heterogeneous energetic landscape within the superlattice. The heterogeneity is quantified by single-particle emission spectroscopy. This powerful multimodal set of observables provides sufficient constraints on a kinetic Monte Carlo simulation of exciton transport to elucidate a composite transport mechanism that includes both near-field FRET and previously neglected far-field emission/reabsorption contributions. Uncovering this mechanism offers a much-needed unified framework in which to characterize transport in QD solids and additional principles for device design.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Chiral edge state control of thermoelectric effects

Thermoelectric responses in two-dimensional electron gases subjected to magnetic fields have the potential to provide unique information about quasiparticle statistics. In this study, we show that chiral edge states play a key role in thermoelectric Hall bar measurements by completely controlling the direction of the internal thermal gradient. To this end, we perform measurements of the magnetothermoelectric responses of cadmium arsenide quantum wells. The magnetothermoelectric responses in the quantum Hall regime agree with theoretical predictions if one considers the role of chiral edge states, which flow in opposite directions on either side of the Hall bar and establish an internal temperature gradient that is perpendicular to the externally applied thermal gradient. We show that the results are self-consistent within this picture under different measurement conditions. We discuss potential applications of the findings, such as in nanoscale control of local temperature gradients and thermoelectric effects along with the characterization of other topological systems with chiral edges states.

Science & Technology - Other Topics↗
DOE OSTI2021

Classification of Semiconductors Using Photoluminescence Spectroscopy and Machine Learning

Photoluminescence spectroscopy is a nondestructive optical method that is widely used to characterize semiconductors. In the photoluminescence process, a substance absorbs photons and emits light with longer wavelengths via electronic transitions. This paper discusses a method for identifying substances from their photoluminescence spectra using machine learning, a technique that is efficient in making classifications. Neural networks were constructed by taking simulated photoluminescence spectra as the input and the identity of the substance as the output. Here, six different semiconductors were chosen as categories: gallium oxide (Ga 2 O 3 ), zinc oxide (ZnO), gallium nitride (GaN), cadmium sulfide (CdS), tungsten disulfide (WS 2 ), and cesium lead bromide (CsPbBr 3 ). The developed algorithm has a high accuracy (>90%) for assigning a substance to one of these six categories from its photoluminescence spectrum and correctly identified a mixed Ga 2 O 3 /ZnO sample.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Standoff Detection of Oil and Powder Mixtures at 12 Meters Using a Tunable Quantum Cascade Laser-Based System with a Close Focus Telescope and Uncooled Infrared Detector

We have designed and demonstrated a quantum cascade laser (QCL) based standoff system that utilizes an uncooled mercury cadmium telluride (MCT) detector with lock-in signal processing for chemical identification at a distance of 12.5 meters in indoor ambient light conditions. In the system, a tunable quad-QCL operating (1 MHz) in quasi-continuous wave mode between 8.45 and 10.03 μm (~1182 to 1000 cm –1 ) serves as the active mid-infrared source for remotely interrogating mineral, powder, and thin film oil samples including powder mixtures (6, 12.5, 25, and 50%) of crystalline quartz (SiO 2 ) in KBr. Light as reflected from a given sample is collected using a 10-inch (25.4 cm) Dall Kirkham telescope and coupled with ZnSe optics to an uncooled MCT detector. Furthermore, the mixture dependence of the highly transparent KBr and strongly absorbing quartz was found to fit a modified version of the Schatz reflectance model for compacted powder mixtures. All reflectance spectra reported are relative to an Au-coated diffuse reflector. A NIST traceable polystyrene standard reflector was also used to determine the QCL wavelength tuning range and calibration.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Modest functional diversity decline and pronounced composition shifts of microbial communities in a mixed waste-contaminated aquifer

Background: Microbial taxonomic diversity declines with increased environmental stress. Yet, few studies have explored whether phylogenetic and functional diversities track taxonomic diversity along the stress gradient. Here, we investigated microbial communities within an aquifer in Oak Ridge, Tennessee, USA, which is characterized by a broad spectrum of stressors, including extremely high levels of nitrate, heavy metals like cadmium and chromium, radionuclides such as uranium, and extremely low pH (< 3). Results: Both taxonomic and phylogenetic α-diversities were reduced in the most impacted wells, while the decline in functional α-diversity was modest and statistically insignificant, indicating a more robust buffering capacity to environmental stress. Differences in functional gene composition (i.e., functional β-diversity) were pronounced in highly contaminated wells, while convergent functional gene composition was observed in uncontaminated wells. The relative abundances of most carbon degradation genes were decreased in contaminated wells, but genes associated with denitrification, adenylylsulfate reduction, and sulfite reduction were increased. Compared to taxonomic and phylogenetic compositions, environmental variables played a more significant role in shaping functional gene composition, suggesting that niche selection could be more closely related to microbial functionality than taxonomy. Conclusions: Overall, we demonstrated that despite a reduced taxonomic α-diversity, microbial communities under stress maintained functionality underpinned by environmental selection.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

The Safe Urban Harvests Study: A Community-Driven Cross-Sectional Assessment of Metals in Soil, Irrigation Water, and Produce from Urban Farms and Gardens in Baltimore, Maryland

BACKGROUND: Emerging evidence suggests social, health, environmental, and economic benefits of urban agriculture (UA). However, limited work has characterized the risks from metal contaminant exposures faced by urban growers and consumers of urban-grown produce. OBJECTIVES: We aimed to answer community-driven questions about the safety of UA and the consumption of urban-grown produce by measuring concentrations of nine metals in the soil, irrigation water, and urban-grown produce across urban farms and gardens in Baltimore, Maryland. METHODS: We measured concentrations of 6 nonessential [arsenic (As), barium (Ba), cadmium (Cd), chromium (Cr), lead (Pb), nickel (Ni)] and three essential [copper (Cu), manganese (Mn), zinc (Zn)] metals in soil, irrigation water, and 13 types of urban-grown produce collected from 104 UA sites. We compared measured concentrations to existing public health guidelines and analyzed relationships between urban soil and produce concentrations. In the absence of guidelines for metals in produce, we compared metals concentrations in urban-grown produce with those in produce purchased from farmers markets and grocery stores (both conventionally grown and U.S. Department of Agriculture–certified organic). RESULTS: Mean concentrations of all measured metals in irrigation water were below public health guidelines. Mean concentrations of nonessential metals in growing area soils were below public health guidelines for Ba, Cd, Pb, and Ni and at or below background for As and Cr. Though we observed a few statistically significant differences in concentrations between urban and nonurban produce items for some combinations, no consistent or discernable patterns emerged. DISCUSSION: Screening soils for heavy metals is a critical best practice for urban growers. Given limitations in existing public health guidelines for metals in soil, irrigation water, and produce, additional exposure assessment is necessary to quantify potential human health risks associated with exposure to nonessential metals when engaging in UA and consuming urban-grown produce. Conversely, the potential health benefits of consuming essential metals in urban-grown produce also merit further research. https://doi.org/10.1289/EHP9431

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Hemicellulose and starch citrate chitosan foam adsorbents for removal of arsenic and other heavy metals from contaminated water

Arsenic and other heavy metal contaminants in water are a significant global health threat. In this study, low-cost, sulfur-free, sustainable, water-insoluble materials with heavy metal remediation properties were produced from renewable resources such as starch, xylan, citric acid, and chitosan. Synthesized starch citrate-chitosan (SCC) foam and xylan citrate-chitosan (XCC) foam were flexible, porous, and elastic. The foams’ arsenic uptake in water was significantly greater than five different commercial metal remediating agents. The mercury and lead uptakes with the synthesized foams were similar to the performance of a commercial sulfur-based product, SorbaTech 450 (ST450). However, the cadmium and selenium uptakes were comparatively lower. The complexation of arsenic with oxygen and nitrogen of the SCC foam was shown with time-of-flight secondary ion mass spectrometry (TOF-SIMS). The XCC foam was also shown to adsorb potassium iodide (KI) at a similar rate to sodium chloride. This may be used to remediate water contaminated with radioactive materials, such as iodine 131.

Materials Science↗