Search NASA⌕ Search

SEARCH · Search NASA

Results for “CORROSION PREVENTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Root cause analysis of a molten salt pump in FLUSTFA

The primary salt pump installed in the high-temperature FLUoride Salt Test Facility (FLUSTFA) was successfully operated for some time, but later ceased operation. To understand what occurred, a Root Cause Analysis (RCA) was performed. Steps taken to try to get the pump operational include adjusting the shaft position, increasing the heating power of the tape heaters on the pump volute, and manually rotating the pump shaft. While removing the insulation, corrosion was noted on the outside of the pump volute, and decolorization of the insulation and tape heaters was observed. Significant corrosion products were also observed in the pump itself and the piping connected to the pump. The nitrogen cover gas was maintained from before salt was introduced into the loop until the pump was dismounted and continues to be maintained even after the pump was removed. After considering probable scenarios, causes were assigned and corrective actions were developed to prevent those causes. Then, the RCA was presented to an advisory committee for review, the “Review Committee,” consisting of experts in large molten salt systems: Brandon Haugh, David Holcomb, Kevin Robb, and Vicente Rojas. As a result, the advisory committee provided comprehensive feedback, which have been incorporated into a revised RCA. Findings have then been summarized and reported in this publication.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Mechanistic insights into Cr(VI) removal by a combination of zero-valent iron and pyrite

Recent studies have revealed that a combination of zero-valent iron (ZVI) and pyrite (FeS 2 ) can effectively remove (Cr(VI)) from water, but the reasons behind this synergistic effect are still unclear. Our batch experiments showed that dissolved oxygen (DO) is a critical factor in the improved removal of Cr(VI) by ZVI and pyrite. When 0.08 g/L pyrite was combined with 0.5 g/L ZVI in the presence of DO, total Cr was reduced from 10 mg/L to 0.02 mg/L within 6 h. Conversely, in the absence of DO, total Cr was only reduced to 5.6 mg/L. DO oxidation of pyrite produced protons that promote ZVI corrosion, and mixing pyrite with water creates dissolved sulfide, which also contributes to the improved removal of Cr(VI). Here, electron microscopy images and X-ray absorption near edge structure analyses revealed that the presence of dissolved sulfide led to the formation of ferrous sulfide precipitates on the ZVI surface, preventing the formation of a passivating layer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

A New General Paradigm for Understanding and Preventing Li Metal Penetration through Solid Electrolytes

The use of lithium (Li) or sodium (Na) metal anodes together with highly ion-conductive solid electrolytes (SEs) could provide batteries with a step improvement in volumetric and gravimetric energy densities. Unfortunately, these SEs face significant technical challenges, in large part because Li and Na dendrites can penetrate through SEs, leading to short circuits. The ability of such a soft material (Li or Na metal) to penetrate through ceramic is surprising from the point of view of models widely used in the Li-battery field. We introduce a concept, new to the battery field, for preventing penetration of lithium dendrites through SEs by putting the SE surfaces into a state of residual compressive stress. For a sufficiently high compressive stress, cracks have difficulty forming, and cracks that do form are forced to close, inhibiting dendrite penetration. This approach is widely used to solve commercially important stress corrosion cracking problems in metals and static fatigue problems in ceramics and glasses (e.g., Gorilla Glass). However, the technique will not be useful for SEs if the Li-ion transport rate through a SE is substantially reduced when the SE is under compression. Our molecular dynamics calculations for Li-ion transport through a common SE demonstrate that the introduction of even very high residual compressive stresses (~10 GPa) has only a modest effect on Li-ion transport kinetics, suggesting that this approach is viable and capable of providing a new paradigm for developing high-performance and mechanically stable SEs.

25 ENERGY STORAGE↗
DOE OSTI2026

Economic Analysis of Condition-Monitoring-Based Predictive Maintenance in Power Plants under Market Elasticity

Condition-monitoring-based predictive maintenance can increase the power plant availability by preventing forced outages. However, the actual on-stream time depends on market elasticity and dynamics, which are affected by cost and penetration of other power generation technologies. This paper develops a systematic approach for the economic analysis of investment in condition monitoring technologies with due consideration of market elasticity. Focus is on corrosion monitoring in coal-fired power plants (CFFPs) since corrosion in high-temperature coal-fired boilers is a leading cause of equipment failure. Investment in sensor networks for measuring corrosion and operating conditions like metal temperature and concentrations of O 2 and SO 2 is investigated. The unscented Kalman filter is used to estimate corrosion in the waterwall section of the boiler under multiple sensor networks. Electricity produced by CFPPs in the future in the U.S. due to changes in availability under market elasticity is studied. Sensitivity of the incremental net present value to factors like the number, type, and cost of sensors is analyzed.

Electrochemistry↗
DOE OSTI2023

A laboratory-scale process for producing dilithium beryllium tetrafluoride (FLiBe) with dissolved uranium tetrafluoride

Flibe Energy, Incorporated (FEI)'s conceptual Lithium Fluoride Thorium Reactor (LFTR) incorporates a chemical processing facility aimed at recovering uranium and other valuable volatile radionuclides while managing harmful radionuclides from the used fuel. The fuel utilized in this reactor is a combination of dilithium beryllium tetrafluoride (Li 2 BeF 4 or FLiBe) and uranium tetrafluoride (UF 4 ), (FLiBe/U). FEI's plan involves extracting the uranium and other valuable volatile fluoride-forming radionuclides using nitrogen trifluoride (NF 3 ). To facilitate laboratory-scale testing of uranium extraction using NF 3 and address the toxicity and physical hazards associated with beryllium and beryllium fluoride (BeF 2 ), we used a two-step process to prepare the simulated fuel salt. The first step entailed thermally decomposing ammonium beryllium tetrafluoride [(NH 4 ) 2 BeF 4 ] (ABeF) through a nominal 3-step process, combined with appropriate amounts of lithium fluoride (LiF) and UF 4 , resulting in the formation of beryllium fluoride (BeF 2 ). In the second step, the mixture was repeatedly melted and frozen at the melting point of FLiBe to prepare the eutectic FLiBe with dissolved UF 4 . Although the concept appears straightforward, the production of FLiBe/U involved various challenges. These challenges included transporting the gaseous decomposition products of ABeF, hydrogen fluoride (HF) and ammonia (NH 3 ), while preventing the formation of ammonium fluoride (NH 4 F). Additionally, it was necessary to control the reaction between the higher-than-anticipated water content in the commercial ABeF with NH 3 , HF, and the condensed NH 4 F, protect UF 4 from forming an unknown black compound, select suitable structural materials to mitigate fluoride corrosion, address the risks associated with beryllium toxicity through equipment design and operational protocols, and monitor process conditions. This article provides an account of the thermal decomposition chemistry observed in the commercial ABeF, describes the FLiBe/U production apparatus, describes the experiences and process refinements developed to prepare FLiBe/U, and presents our characterizations of prepared FLiBe/U.

Ammonium beryllium fluoride thermal decomposition↗
DOE OSTI2020

Ion irradiation effects on Cr-coated zircaloy-4 surface wettability and pool boiling critical heat flux.

The concept of coating the currently used nuclear fuel cladding (zirconium-based alloy, typically Zircaloy-4 or Zirc-4) with an oxidation preventive layer is a progressing Accident tolerant Fuel (ATF) candidate alloys. The coated Zirc-4-based alloys could be a solution to suppress undesirable fast reaction kinetics with high-temperature steam. Zirc-4 has been the most preferred cladding material in pressurized water reactors (PWRs). Chromium (Cr) based alloys as a coating material provides excellent corrosion protection and good strength and wear resistance. In this paper, we present the surface wettability measurements and pool boiling Critical Heat Flux (CHF) for Cr-coated Zirc-4 claddings pre- and post-exposure to an ion irradiation environment. The wettability measurements, including static contact angle (contact angle, θ) and average surface roughness (surface roughness, Ra), are introduced for samples of different coating thicknesses (5–30 μm thick). The coatings fabricated by the cold spray of Cr-Al particles to 10 mm × 10 mm × 1.95 mm Zirc-4 substrates. Post fabrication, a Pilgering (cold rolling) process, was applied to finalize the coating thickness and resulted in a significant reduction in surface roughness of initially fabricated rough surfaces. The process produced three distinguished samples 5-μm unpolished (as machined), 5-μm, and 30-μm polished (cold rolled). The measurements are presented for the three surfaces and bare Zirc-4 as a baseline surface. The contact angle analyses were implemented in theoretical models from the literature to predict pool boiling CHF. Pool boiling experiments were conducted to measure the pool boiling CHF values and compare them to the predicted values. Scanning Electron Microscope (SEM) images and Energy Dispersive X-ray Spectroscopy (EDS) analysis was performed to characterize the surfaces for better understanding and interpreting the results. The SEM images showed localized surface damage due to ion irradiation. No recognized change in the measured surface roughness due to ion irradiation. The contact angles of irradiated Cr-coated surfaces are consistently higher (10°) than pre-irradiated surfaces. Decreasing the Cr-coating layer thickness resulted in lower contact angle pre- and post- ion irradiation. The predicted pool boiling CHF using the Kandlikar model is in good agreement with the experimentally measured CHF values within ±12% for all samples.

36 MATERIALS SCIENCE↗
NASA NTRS2016

NASA and ESA Collaboration on Alternative to Nitric Acid Passivation: Parameter Optimization of Citric Acid Passivation for Stainless Steel Alloys

National Aeronautics and Space Administration (NASA) Headquarters chartered the Technology Evaluation for Environmental Risk Mitigation Principal Center (TEERM) to coordinate agency activities affecting pollution prevention issues identified during system and component acquisition and sustainment processes. The primary objectives of NASA TEERM are to: Reduce or eliminate the use of hazardous materials or hazardous processes at manufacturing, remanufacturing, and sustainment locations. Avoid duplication of effort in actions required to reduce or eliminate hazardous materials through joint center cooperation and technology sharing. Corrosion is an extensive problem that affects the National Aeronautics and Space Administration (NASA) and the European Space Agency (ESA). The damaging effects of corrosion result in steep costs, asset downtime affecting mission readiness, and safety risks to personnel. Consequently, it is vital to reduce corrosion costs and risks in a sustainable manner. NASA and ESA have numerous structures and equipment that are fabricated from stainless steel. The standard practice for protection of stainless steel is a process called passivation. Passivation is defined by The American Heritage Dictionary of the English Language as to treat or coat (a metal) in order to reduce the chemical reactivity of its surface. Passivation works by forming a shielding outer (metal oxide) layer that reduces the impact of destructive environmental factors such as air or water. Consequently, this process necessitates a final product that is very clean and free of iron and other contaminants. Typical passivation procedures call for the use of nitric acid; however, there are a number of environmental, worker safety, and operational issues associated with its use. Citric acid is an alternative to nitric acid for the passivation of stainless steels. Citric acid offers a variety of benefits including increased safety for personnel, reduced environmental impact, and reduced operational cost. The primary objective of this effort is to qualify citric acid as an environmentally-preferable alternative to nitric acid for the passivation of stainless steel alloys. While citric acid use has become more prominent in industry, there is little evidence that citric acid is a technically sound passivation agent, especially for the unique and critical applications encountered by NASA and ESA.

citric acid passivation↗
DOE OSTI2023

Results of FY 2023 Alloy 617 and Alloy 709 High-Temperature Crack-Growth Testing

This report summarizes the work performed at Idaho National Laboratory under the “Creep, fatigue and creep-fatigue crack growth tests” task of the “Long-Term VHTR Material Qualification – INL” work package. Work was performed this year to validate the crack growth monitoring setup used with the test frames against both continuous crack length monitoring using an optical camera, as well as post-mortem analysis of marker bands on the fracture surface. Delays prevented the use of a gauge to measure load-line displacement for early tests, and so the creep-fatigue crack growth setup was evaluated using the actuator displacement for a load-line displacement setup. While not ideal, this allowed examination of the shortcomings with the current software setup that was originally designed for performing stress corrosion crack growth rate studies. The method for data collection was modified to link the crack growth monitoring software with Instron’s Wave Matrix software. Once the load-line displacement gauge arrived, the crack growth equipment was successfully modified to permit continuous monitoring of both load-line displacement and crack length. This is critical for creep-fatigue and creep crack growth rate studies for ductile material, as it permits the C* and Ct analyses. Test results are shown for Alloy 617 fatigue and creep-fatigue (without the gauge for load-line displacement measurements), as well as creep-fatigue of Alloy 709, which was performed with the completed test setup, allowing for crack length and load-line displacement monitoring.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1983

Low temperature hot corrosion

The reaction of Co-Cr, Ni-Cr, Co-Cr-Al, and Ni-Cr-Al alloys with Na2SO4 in the presence of SO3 at temperatures between 700 and 750 C leads to the formation of liquid CoSO4-Na2SO4 or NiSO4-Na2SO4 deposits on the alloy surface. The formation of Cr2O3 and/or Al2O3 below this deposit results in a locally low P(O2) and a higher P(S2) and P(SO2). It is noted that these conditions can prevent protective oxide formation either by sulfide formation in the alloy, which localizes the Cr and/or Al in discrete particles, or by acid fluxing involving a reaction between Al2O3 or Cr2O3 and SO2 to form a salt-soluble species and subsequent reprecipitation as porous oxides in regions of higher P(O2). These processes may occur simultaneously, although a given alloy generally exhibits features of predominantly one type. Here, the Ni-Cr and Ni-Cr-Al alloys, and to some extent the Co-Cr alloys, exhibit features indicative of the sulfidation mechanism, whereas the morphology for the Co-Cr-Al alloy is more consistent with a predominant acid fluxing mechanism.

Chiang, K. T.↗
DOE OSTI2020

Ammonia Permeation Through Inorganic Membranes

Moisture probes are used in the tritium facility to measure the moisture content of the gas stream. When tritium reacts with nitrogen to form ammonia, the ammonia gas damages the sensitive moisture probe. The gas stream tested during this experiment for moisture probe protection is composed of nitrogen and argon gas in conjunction with ammonia and water vapor. The gas stream is filtered through an inorganic membrane due to the high reactivity of tritium and a residual gas analyzer (RGA) is used to measure the ammonia and water vapor in the gas stream, as well as the permeability of nitrogen and argon through the inorganic membranes. The membranes tested were boron nitride and silver. The permeability was compared for each membrane at different pressures and flow rates. Fourier-transformed infrared spectroscopy (FT-IR) was used to compare the membranes before and after ammonia permeation. Ammonia gas is a byproduct formed from tritium gas reacting with nitrogen in the gas stream, similar to the Haber Process which occurs when hydrogen reacts with nitrogen [2]. The corrosive nature of ammonia damages metals and sensitive instruments such as moisture probes. Moisture probes are essential in various gas and liquid processes for measuring the moisture content of a gas. Membrane research has found that graphene oxide membranes successfully uptake ammonia from the gas stream at a humidity of approximately 30% at which point the pores pin closed, preventing gas permeation. Further research is being conducted to find an inorganic membrane that will prevent ammonia permeation thus circumventing damage to the sensitive moisture probe. The permeation measurements for argon and nitrogen gas and water and ammonia vapor were measured at various pressures of 800, 1000, 1200, 1500, 1800, and 2000 torr. The permeability average (PA) was calculated for each filter using a Barrer calculation. The average permeations for each filter were then compared. The gas composition was measured using the RGA Nitrogen was permeated through the membranes after ammonia permeation and a FT-IR spectrum was obtained. Boron Nitride: As the nitrogen pressure increased, the permeability of the membrane decreased from 800-1200 torr and remained relatively unchanged from 1200-2000 torr. The membrane exhibited a slight decrease in argon permeability from 800-1200 torr and a slight increase from 1500-2000 torr. The boron nitride membrane when permeated with ammonia and nitrogen prevented less ammonia permeation compared to the blank filter. The boron nitride filter demonstrated a decrease in permeability after ammonia permeation. Silver Membrane: When permeated with nitrogen alone, the membrane permeability decreased from 800 torr to 1200 torr. The permeability of the membrane showed little difference as pressure increased from 1200 torr. When permeated with argon, the same phenomenon occurred but on a much smaller scale. When compared to the blank and the boron nitride membranes the silver membrane exhibited significantly lower permeability. This may be in part due to the coating on the silver membrane and differences in pore size of the membranes. During permeation with ammonium hydroxide vapor and nitrogen, the partial pressure of the ammonia increased as compared to the blank membrane. The permeability before and after permeation with ammonia and nitrogen were compared. Permeability values suggested that after being permeated with the ammonia that the permeability for lower pressures increased slightly. There was no significant change in the FT-IR spectrums before and after permeation. Future work: Continue testing various inorganic membranes for ammonia permeation. Further research chemical separation of ammonia from the gas stream, which may prove difficult due to the high reactivity of tritium.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Understanding the role of water-soluble guar gum binder in reducing capacity fading and voltage decay of Li-rich cathode for Li-ion batteries

The practical application of high-capacity Li-rich cathode materials is hindered by capacity fading and voltage decay. The capacity fading and voltage decay could be effectively overcome by using water-soluble guar gum (GG) binder instead of traditional polyvinylidene fluoride (PVDF). However, the specific role of the GG binder is not clear yet, though the GG binder can significantly improve the electrochemical performance of Li-rich cathode. To understand the effect of GG binder on the morphology, microstructure of electrode and electrode/electrolyte interfaces, ex-situ scanning electron microscope (SEM), transmission electron microscope (TEM), X-ray adsorption near edge spectroscopy (XANES), in-situ electrochemical impedance spectroscopy (EIS) were applied to comparatively study the charge-discharge processes of Li-rich Li 1.2 Ni 0.2 Mn 0.6 O 2 cathode when using GG and PVDF as binders. The results indicate that the GG binder can prevent electrode crack and active material loss, ascribing to the strong mechanical adhesion of GG binder with active material particles and current collector. It has found that the GG binder can also induce the formation of a uniform layer on Li 1.2 Ni 0.2 Mn 0.6 O 2 particles’ surface. As a consequence, both the electrolyte decomposition and the electrode corrosion were significantly inhibited. The strong chelation between Mn 2+ and polar OH group restrain Mn ion dissolution, which contributes to surface structural transformation mitigation. Here, our study reveals the role of water-soluble GG binder in reducing capacity fading and voltage decay of Li-rich material and is of great importance in design functional binders for high-performance Li-rich electrodes.

25 ENERGY STORAGE↗
DOE OSTI2023

LiH formation and its impact on Li batteries revealed by cryogenic electron microscopy

Little is known about how evolved hydrogen affects the cycling of Li batteries. Hypotheses include the formation of LiH in the solid-electrolyte interphase (SEI) and dendritic growth of LiH. Here, we discover that LiH formation in Li batteries likely follows a different pathway: Hydrogen evolved during cycling reacts to nucleate and grow LiH within already deposited Li metal, consuming active Li. We provide the evidence that LiH formed in Li batteries electrically isolates active Li from the current collector that degrades battery capacity. We detect the coexistence of Li metal and LiH also on graphite and silicon anodes, showing that LiH forms in most Li battery anode chemistries. Last, we find that LiH has its own SEI layer that is chemically and structurally distinct from the SEI on Li metal. Our results highlight the formation mechanism and chemical origins of LiH, providing critical insight into how to prevent its formation.

25 ENERGY STORAGE↗
NASA NTRS2008

John F. Kennedy Space Center's Technology Development and Application 2006-2007 Report

Topics covered include: Reversible Chemochromic Hydrogen Detectors; Determining Trajectory of Triboelectrically Charged Particles, Using Discrete Element Modeling; Using Indium Tin Oxide To Mitigate Dust on Viewing Ports; High-Performance Polyimide Powder Coatings; Controlled-Release Microcapsules for Smart Coatings for Corrosion Applications; Aerocoat 7 Replacement Coatings; Photocatalytic Coatings for Exploration and Spaceport Design; New Materials for the Repair of Polyimide Electrical Wire Insulation; Commodity-Free Calibration; Novel Ice Mitigation Methods; Crack Offset Measurement With the Projected Laser Target Device; New Materials for Structural Composites and Protective Coatings; Fire Chemistry Testing of Spray-On Foam Insulation (SOFI); Using Aerogel-Based Insulation Material To Prevent Foam Loss on the Liquid-Hydrogen Intertank; Particle Ejection and Levitation Technology (PELT); Electrostatic Characterization of Lunar Dust; Numerical Analysis of Rocket Exhaust Cratering; RESOLVE Projects: Lunar Water Resource Demonstration and Regolith Volatile Characterization; Tribocharging Lunar Soil for Electrostatic Beneficiation; Numerically Modeling the Erosion of Lunar Soil by Rocket Exhaust Plumes; Trajectory Model of Lunar Dust Particles; Using Lunar Module Shadows To Scale the Effects of Rocket Exhaust Plumes; Predicting the Acoustic Environment Induced by the Launch of the Ares I Vehicle; Measuring Ultrasonic Acoustic Velocity in a Thin Sheet of Graphite Epoxy Composite; Hail Size Distribution Mapping; Launch Pad 39 Hail Monitor Array System; Autonomous Flight Safety System - Phase III; The Photogrammetry Cube; Bird Vision System; Automating Range Surveillance Through Radio Interferometry and Field Strength Mapping Techniques; Next-Generation Telemetry Workstation; GPS Metric Tracking Unit; and Space-Based Range.

Source record↗
NASA NTRS2024

Land Use Control Implementation Plan

This Land Use Control Implementation Plan (LUCIP) has been prepared to inform current and potential future users of the Corrosion Atmospheric Exposure Facility (CAEF) of institutional controls that have been implemented at the site. 1 Although most areas at CAEF do not pose current unacceptable risks to human health or the environment, areas of arsenic-impacted soil exceeding the Florida Department of Environmental Protection (Florida DEP) residential soil cleanup target levels (SCTLs) have been identified. Institutional land use controls (LUCs) are necessary to prevent contact with surface and subsurface soils at the site. Controls will include periodic inspection, condition certification, and agency notification.

soil↗
NASA NTRS2000

Asbestos Free Insulation Development for the Space Shuttle Solid Propellant Rocket Motor (RSRM)

Asbestos has been used for many years as an ablation inhibitor in insulating materials. It has been a constituent of the AS/NBR insulation used to protect the steel case of the RSRM (Reusable Solid Rocket Motor) since its inception. This paper discusses the development of a potential replacement RSRM insulation design, several of the numerous design issues that were worked and processing problems that were resolved. The earlier design demonstration on FSM-5 (Flight Support Motor) of the selected 7% and 11% Kevlar(registered) filled EPDM (KF/EPDM) candidate materials was expanded. Full-scale process simulation articles were built and FSM-8 was manufactured using multiple Asbestos Free (AF) components and materials. Two major problems had to be overcome in developing the AF design. First, bondline corrosion, which occurred in the double-cured region of the aft dome, had to be eliminated. Second, KF/EPDM creates high levels of electrostatic energy (ESE), which does not readily dissipate from the insulation surface. An uncontrolled electrostatic discharge (ESD) of this surface energy during many phases of production could create serious safety hazards. Numerous processing changes were implemented and a conductive paint was developed to prevent exposed external insulation surfaces from generating ESE/ESD. Additionally, special internal instrumentation was incorporated into FSM-8 to record real-time internal motor environment data. These data included inhibitor insulation erosion rates and internal thermal environments. The FSM-8 static test was successfully conducted in February 2000 and much valuable data were obtained to characterize the AF insulation design.

Allred, Larry D.↗
DOE OSTI2025

A Novel Approach for Microencapsulating Salt Hydrate-Based Phase Change Materials

Energy storage technologies, particularly those utilizing phase change materials (PCMs), have gained attention for their high energy density and efficient thermal management. PCMs, which store energy through solid-liquid phase transitions, can efficiently capture and release thermal energy, but face the challenge of leakage during the phase change process. Inorganic PCMs, such as salt hydrates, offer high energy storage capacity, but are difficult to encapsulate due to their corrosive nature. Conventional encapsulation techniques for inorganic PCMs are limited, particularly for scalable applications. In this work, we present an innovative method for the encapsulation of salt hydrate-based inorganic PCMs (CaCl 2 ·6H 2 O) using co-axial electrospinning. The process involves the creation of co-axial fibers, with salt hydrate as the core and polymer (e.g., PVP) as the outer shell, effectively preventing leakage and improving the stability of the PCM. This approach demonstrates the potential for scalable microencapsulation of inorganic PCMs, marking the first report of using co-axial electrospinning for this purpose. This novel technique could contribute to enhancing the performance and applicability of PCMs in thermal energy storage systems and other energy efficiency applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Water-Fed Hydroxide Exchange Membrane Electrolyzer Enabled by a Fluoride-Incorporated Nickel–Iron Oxyhydroxide Oxygen Evolution Electrode

Here, we have developed a dissolved oxygen and galvanic corrosion method to synthesize vertically aligned fluoride-incorporated nickel–iron oxyhydroxide nanosheet arrays on a compressed Ni foam as an efficient self-supported oxygen evolution electrode. It is integrated with poly(aryl piperidinium) hydroxide exchange membrane and ionomers with high ion exchange capacity into a hydroxide exchange membrane electrolyzer fed with pure water, which achieves a performance of 1020 mA cm –2 at 1.8 V and prevents the detachment of catalysts during continuous operation (>160 h at 200 mA cm –2 ). Furthermore, this work provides a potential pathway for massively producing low-cost hydrogen using intermittent renewable energy sources.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1997

Oxidation Resistance and Critical Sulfur Content of Single-Crystal Superalloys

The high-temperature components of a jet turbine engine are made from nickel-base superalloys. These components must be able to withstand high stresses, fatigue, and corrosive reactions with high-temperature gases. Such oxidation resistance is associated with slow-growing Al2O3 scales that remain adherent to superalloy components after many thermal cycles. Historically, good oxidation resistance has been obtained by coating these components with Ni-Cr-Al-Y coatings, where small additions of yttrium (Y) were necessary for scale adhesion. Subsequently, it was found that the Y aids scale adhesion by preventing sulfur from segregating to the scale metal interface and thus preventing the sulfur from weakening the oxide-metal bonds. Y is a difficult element to incorporate in single-crystal superalloy castings, but it was shown in early work at the NASA Lewis Research Center that good adhesion could be obtained for low-sulfur, uncoated, singlecrystal superalloys, without Y additions. Low sulfur contents for these uncoated superalloys were achieved in the laboratory by a high-temperature hydrogen annealing process. This process allows segregation and surface cleaning of sulfur monolayers in a reducing environment. Another approach is to remove sulfur from the alloy in the melting process. The present study was designed to establish a guideline for the minimum level of desulfurization needed to achieve maximum performance. Coupons of various thicknesses of the superalloy PWA 1480 were hydrogen annealed at various times (8 to 100 hr) and temperatures (1000 to 1300 C), resulting in coupons with sulfur contents ranging from about 0.05 to 5 ppm. Cyclic oxidation tests at 1100 C were then used to assess adhesion and spalling. The weight change of one set of 20-mil (0.5-mm) samples, annealed for 20 hr at 1000, 1100, 1200, and 1300 C, is shown in the following figure. Clearly, the effect of the annealing temperature is quite dramatic in that the higher temperatures produced scales that spalled very little, whereas the lower temperatures resulted in severe weight losses comparable to those for the as-received, unannealed sample.

Smialek, James L.↗