Search NASA⌕ Search

SEARCH · Search NASA

Results for “Compression Ratio”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Advanced ramjet concepts program

Uniquely advantageous features, on both the performance and weight sides of the ledger, can be achieved through synergistic design integration of airbreathing and rocket technologies in the development of advanced orbital space transport propulsion systems of the combined cycle type. In the context of well understood advanced airbreathing and liquid rocket propulsion principles and practices, this precept of synergism is advanced mainly through six rather specific examples. These range from the detailed component level to the overall vehicle system level as follows: using jet compression; achieving a high area ratio rocket nozzle; ameliorating gas generator cycle rocket system deficiencies; using the in-duct special rocket thrust chamber assembly as the principal scramjet fuel injection operation; using the unstowed, covered fan as a duct closure for effecting high area ratio rocket mode operation; and creating a unique airbreathing rocket system via the onboard, cryogenic hydrogen induced air liquefaction process.

Leingang, J. L.↗
NASA NTRS1992

The elastic and yield behavior of polyethylene tubes subjected to biaxial loadings

The elastic and yield response of extruded thin-walled high-density polyethylene tubes with a density in the range of 0.961 to 0.964 gm/cu cm was investigated. Material properties in the axial and hoop directions were measured, and the tubes were found to be mildly transversely isotropic. The yield response was pressure sensitive, and was well predicted using the pressure-modified Hill criterion using a compressive to tensile yield strength ratio of 1:12.

Tuttle, M. E.↗
NASA NTRS1949

Critical combinations of shear and direct axial stress for curved rectangular panels

A solution is presented for the problem of the buckling of curved rectangular panels subjected to combined shear and direct axial stress. Charts giving theoretical critical combinations of shear and direct axial stress are presented for panels having five different length-width ratios. Because the actual critical compressive stress of rectangular panels having substantial curvature is known to be much lower than the theoretical value, a semiempirical method of analysis of curved panels subjected to combined shear and direct axial stress is presented for use in design. (author

PLATES - STRESSES, SHEARING CURVED↗
NASA NTRS1951

Stability of the cylindrical shell of variable curvature

This report is a first attempt to devise a calculation method for representing the buckling behavior of cylindrical shells of variable curvature. The problem occurs, for instance, in dimensioning wing noses, the stability of which is decisively influenced by the variability of curvature. The calculation is made possible by simplifying the stability equations (permissible for the shell of small curvature) and by assuming that the curvature 1/R as a function of the arc lengths can be represented by a very few Fourier terms. The formulas for the special case of an ellipse-like half oval with an axis ratio 1/3 ?= e ?= 1 under compression in longitudinal direction,shear, and a combination of shear and compression were evaluated. However, the results can also be applied approximately to an unsymmetrical oval-shell segment under compression, shear, and bending so that the numerical values contained in the diagrams 10 to 12 represent directly dimensioning data for the wing nose.

LOADS AND STRESSES, STRUCTURAL - BENDING↗
NASA NTRS1993

Humidity effects on soluble core mechanical and thermal properties (polyvinyl alcohol/microballoon composite) type CG extendospheres, volume 2

This document constitutes the final report for the study of humidity effects and loading rate on soluble core (PVA/MB composite material) mechanical and thermal properties under Contract No. 100345. This report describes test results procedures employed, and any unusual occurrences or specific observations associated with this test program. The primary objective of this work was to determine if cured soluble core filler material regains its tensile and compressive strength after exposure to high humidity conditions and following a drying cycle. Secondary objectives include measurements of tensile and compressive modulus, and Poisson's ratio, and coefficient of thermal expansion (CTE) for various moisture exposure states. A third objective was to compare the mechanical and thermal properties of the composite using 'SG' and 'CG' type extendospheres. The proposed facility for the manufacture of soluble cores at the Yellow Creek site incorporates no capability for the control of humidity. Recent physical property tests performed with the soluble core filler material showed that prolonged exposure to high humidity significantly degradates in strength. The purpose of these tests is to determine if the product, process or facility designs require modification to avoid imparting a high risk condition to the ASRM.

Source record↗
NASA NTRS2005

Characterization of Ice for Return-to-Flight of the Space Shuttle: Soft Ice - Part 2

In support of characterizing ice debris for return-to-flight (RTF) of NASA's space shuttle, we have determined the microstructure, density and compressive strength (at -10 C at approximately 0.3 per second) of porous or soft ice that was produced from both atmospheric water and consolidated snow. The study showed that the atmospheric material was generally composed of a mixture of very fine (0.1 to 0.3 millimeters) and coarser (5 to 10 millimeter) grains, plus air bubbles distributed preferentially within the more finely-grained part of the microstructure. The snow ice was composed of even finer grains (approximately 0.05 millimeters) and contained more pores. Correspondingly, the snow ice was of lower density than the atmospheric ice and both materials were significantly less dense than hard ice. The atmospheric ice was stronger (approximately 3.8 MPa) than the snow ice (approximately 1.9 MPa), but weaker by a factor of 2 to 5 than pore-free hard ice deformed under the same conditions. Zero Values are given for Young's modulus, compressive strength and Poisson's ratio that can be used for modeling soft ice from the external tank (ET).

Schulson, Erland M.↗
NASA NTRS1973

Striated nozzle flow with small radius of curvature ratio throats

A theory is presented that makes it possible to apply one-dimensional techniques to compressible striated nozzle flow with small radius of curvature ratio throats. The throat plane solution is shown to approximate the two-dimensional axisymmetric flowfield and can be used for analyzing the throat plane in converging-diverging type nozzles with striated flow for radius of curvature throat ratios down to 0.25.

Norton, D. J.↗
NASA NTRS1933

Strength Tests of Thin-walled Duralumin Cylinders in Pure Bending

This report is the third of a series presenting the results of strengths tests on thin-walled cylinders and truncated cones of circular and elliptic section; it includes the results obtained from pure bending tests on 58 thin-walled duralumin cylinders of circular section with ends clamped to rigid bulkheads. The tests show that the stress on the extreme fiber at failure as calculated by the ordinary theory of bending is from 30 to 80 percent greater than the compressive stress at failure for thin-walled cylinders in compression. The tests also show that length/radius ratio has no consistent effect upon the bending strength and that the size of the wrinkles that form on the compression half of a cylinder in bending is approximately equal to the size of the wrinkles that form in the complete circumference of a cylinder of the same dimensions in compression.

CONES, TRUNCATED - STRENGTH TESTS↗
NASA NTRS2019

Performance Optimization of Plate Airfoils for Martian Rotor Applications Using a Genetic Algorithm

The Mars Helicopter Technology Demonstrator will be flying on the NASA Mars 2020 rover mission scheduled to launch in July of 2020. The goal is to demonstrate the viability and potential of heavier-than-air vehicles in the Martian atmosphere. Research is performed at the Jet Propulsion Laboratory and NASA Ames Research Center to extend these capabilities and develop the Mars Science Helicopter as the next possible step for Martian rotorcraft. The Mars Science Helicopter mass is scaled up to the 5 to 20 kg range, allowing a greater payload (approximately 0.5 to 2.0 kg), and greater range (approximately 3 km). Key to achieving these targets is careful aerodynamic rotor design. The Martian atmosphere’s low density and the small helicopter rotors result in very low chord-based Reynolds number flows, which reduces rotor performance. A continuous genetic algorithm is developed to optimize airfoil shapes at representative conditions for the Martian atmosphere. Previous research indicates that sharp leading edges and plate-like airfoils can out-perform conventional airfoil shapes. The present optimization allows for camber and thickness variation of curved and polygonal thin airfoils with sharp leading edges. The airfoil performance is evaluated at the highest attainable liftto- drag ratio near a moderate lift coefficient at compressible Mach numbers, as expected for Martian rotor application. Increases between 16% and 29% in airfoil lift-to-drag ratio at fixed lift coefficients are observed when compared with the Mars Helicopter Technology Demonstrator airfoils. Improvements in hover figure of merit are estimated to be between 4% and 10%, when applied to the Mars Helicopter Technology Demonstrator.

Koning, Witold J. F.↗
NASA NTRS1948

An Analysis of the Effects of Wing Aspect Ratio and Tail Location on Static Longitudinal Stability Below the Mach Number of Lift Divergence

An analysis is presented of the influence of wing aspect ratio and tail location on the effects of compressibility upon static longitudinal stability. The investigation showed that the use of reduced wing aspect ratios or short tail lengths leads to serious reductions in high-speed stability and the possibility of high-speed instability.

Axelson, John A.↗
NASA NTRS1998

Anomalous Buckling Characteristics of Laminated Metal-Matrix Composite Plates with Central Square Holes

Compressive buckling analysis was performed on metal-matrix composite (MMC) plates with central square holes. The MMC plates have varying aspect ratios and hole sizes and are supported under different boundary conditions. The finite-element structural analysis method was used to study the effects of plate boundary conditions, plate aspect ratio, hole size, and the composite stacking sequence on the compressive buckling strengths of the perforated MMC plates. Studies show that by increasing the hole sizes, compressive buckling strengths of the perforated MMC plates could be considerably increased under certain boundary conditions and aspect ratios ("anomalous" buckling behavior); and that the plate buckling mode could be symmetrical or antisymmetrical, depending on the plate boundary conditions, aspect ratio, and the hole size. For same-sized plates with same-sized holes, the compressive buckling strengths of the perforated MMC plates with [90/0/0/90]2 lamination could be as much as 10 percent higher or lower than those of the [45/- 45/- 45/45]2 laminations, depending on the plate boundary conditions, plate aspect ratios, and the hole size. Clamping the plate edges induces far stronger "anomalous" buckling behavior (enhancing compressive buckling strengths at increasing hole sizes) of the perforated MMC plates than simply supporting the plate edges.

Ko, William L.↗
NASA NTRS1985

Vibrations of circular orthotropic plates in affine space

The vibration of an initially compressed plate having a circular geometry and orthotropy is examined in an affine space. The classical linear plate theory and Hamilton's principle are employed. The equations of motion of the plate are particularly simple in the chosen affine space, permitting a free-vibration study of the entire spectrum of composite materials with polar orthotropy. Approximate but very accurate standing-wave-type mode shapes are used in solving the essentially double eigenvalue problem to determine the effects of midplane forces on the vibration frequencies of the plate. The results indicate that the affine-space frequency increases with increasing stiffness ratio but decreases with increasing midplane compression. It is also discovered that, contrary to the trends observed for rectangular geometry and orthotropy by Oyibo (1981), Brunelle (1982), and Brunelle and Oyibo (1983), the affine-space frequency increases with increasing generalized Poisson's ratio.

Oyibo, G. A.↗
NASA NTRS1972

The earth's bow shock in an oblique interplanetary field.

The pressure, magnetic field, temperature, particle density, and stream velocity throughout the magnetosheath have been calculated in the plane containing the interplanetary field and solar wind velocity vector for various orientations of the interplanetary magnetic field and various assumed ratios of specific heats of the compressed solar wind. Jump conditions at the bow shock gave initial conditions in the shocked plasma from which the appropriate hydromagnetic equations (for blunt bodies in the subsonic region near the subsolar point and for the method of characteristics in the supersonic region back in the tail) were integrated numerically back to the surface of the magnetosphere. Explicit consideration of the magnetic field shows that a net asymmetrical force on the magnetopause produces a side force, or 'lift' in addition to the well-known drag on the magnetosphere.

Shen, W.-W.↗
NASA NTRS1985

Effect of Steady-State Temperature Distortion on Inlet Flow to a High-Bypass-Ratio Turbofan Engine

The effects of circumferential inlet temperature distortion on the flow characteristics between a distortion generator and a high bypass ratio turbofan engine and through its compression system were evaluated to support the effort to generate analytical models. The flow characteristics are defined by the inlet duct, the flow angles, and the total temperature, total pressure, and static pressure profiles in the inlet duct and through the fan and compressor. The effects of Reynolds number, rotor speed, and distortion extent are also considered.

Soeder, R. H.↗
NASA NTRS1989

Injectant mole-fraction imaging in compressible mixing flows using planar laser-induced iodine fluorescence

A technique is described for imaging the injectant mole-fraction distribution in nonreacting compressible mixing flow fields. Planar fluorescence from iodine, seeded into air, is induced by a broadband argon-ion laser and collected using an intensified charge-injection-device array camera. The technique eliminates the thermodynamic dependence of the iodine fluorescence in the compressible flow field by taking the ratio of two images collected with identical thermodynamic flow conditions but different iodine seeding conditions.

Hartfield, Roy J., Jr.↗
NASA NTRS1942

Tensile and pack compressive tests of some sheets of aluminum alloy, 1025 carbon steel, and chromium-nickel steel

Tensile and compressive stress-strain curves, stress-deviation curves, and secant modulus-stress curves are given for longitudinal and transverse specimens of 17S-T, 24S-T, and 24S-RT aluminum-alloy sheet in thicknesses from 0.032 to 0.081 inch, 1025 carbon steel sheet in thicknesses of 0.054 and 0.120 inch, and chromium-nickel steel sheet in thicknesses form 0.020 to 0.0275 inch. Significant differences were found between the tensile and the compressive stress-strain curves, and also the corresponding corollary curves; similarly, differences were found between the curves for the longitudinal and transverse directions. These differences are of particular importance in considering the compressive strength of aircraft structures made of thin sheet. They are explored further for the case of compression by giving tangent modulus-stress curves in longitudinal and transverse compression and dimensionless curves of the ratio of tangent modulus to Young's modulus and of the ratio of reduced modulus for a rectangular section to Young's modulus, both plotted against the ratio of stress to secant yield strength.

Atchison, C S↗
NASA NTRS1994

Low-Noise Rotorcraft Blades

Blades of helicopter rotors, tilt rotors, and like reshaped to reduce noise, according to proposal. Planform features combination of rearward and forward sweep. Forward sweep over large outer portion of blade constitutes primary noise-reduction feature. Relieves some of compressive effect in tip region, with consequent reduction of noise from compressive sources. Performance at high advance ratio improved. Cabin vibration and loading noise reduced by load-averaging effect of double-sweep planform. Aft-swept section provides balancing of aerodynamic and other dynamic forces on blade along 1/4-chord line of straight inboard section and along projection of line to outermost blade radius. Possible for hub-hinge forces and moments to remain within practical bounds. Provides stabilizing blade forces and moments to counteract any instability caused by forward sweep.

Brooks, Thomas F.↗