Search NASA⌕ Search

SEARCH · Search NASA

Results for “Computer Terminals”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Method for the calculation of spacecraft umbra and penumbra shadow terminator points

A method for calculating orbital shadow terminator points is presented. The current method employs the use of an iterative process which is used for an accurate determination of shadow points. This calculation methodology is required since orbital perturbation effects can introduce large errors when a spacecraft orbits a planet in a high altitude and/or highly elliptical orbit. To compensate for the required iteration methodology, all reference frame change definitions and calculations are performed with quaternions. Quaternion algebra significantly reduces the computational time required for the accurate determination of shadow terminator points.

Ortizlongo, Carlos R.↗
NASA NTRS1977

Interactive LORAN-C to geographic and geographic-to-LORAN-C computation

The LORAN program is stored in CMS disk files for use by Avionics Engineering Center terminal users. A CMS EXEC file named LORAN controls program operation. The user types LORAN and the program then prompts for data input and produces output on the terminal. The FORTRAN program refers to a disk file of LORAN master data giving station locations, coding delays, repetition rate and station pair identification letters. For Geographic-to-LORAN conversion, no iterative computations are required; the program is a straightforward coordinate conversion based upon the techniques described by the Navy. For LORAN-to-Geographic conversion, the original Navy program required a dead-reckoned position, near the actual unknown fix, to begin computations. No iteration was performed to obtain the LORAN fix, but internal program errors occurred at execution time if the dead-reckoned fix were displaced from the actual fix by more than a few minutes of latitude or longitude. In order to enhance usefulness of the program for the terminal user, an iterative routine was added which allows a single dead-reckoned position to be entered from the master data file for each LORAN chain. The results compare exactly with the LORAN-C navigation chart, and provide adequate benchmark data for general aviation flight planning and data analysis.

Piecuch, L. M.↗
NASA NTRS1993

Design of Center-TRACON Automation System

A system for the automated management and control of terminal area traffic, referred to as the Center-TRACON Automation System (CTAS), is being developed at NASA Ames Research Center. In a cooperative program, NASA and FAA have efforts underway to install and evaluate the system at the Denver area and Dallas/Ft. Worth area air traffic control facilities. This paper will review CTAS architecture, and automation functions as well as the integration of CTAS into the existing operational system. CTAS consists of three types of integrated tools that provide computer-generated advisories for both en-route and terminal area controllers to guide them in managing and controlling arrival traffic efficiently. One tool, the Traffic Management Advisor (TMA), generates runway assignments, landing sequences and landing times for all arriving aircraft, including those originating from nearby feeder airports. TMA also assists in runway configuration control and flow management. Another tool, the Descent Advisor (DA), generates clearances for the en-route controllers handling arrival flows to metering gates. The DA's clearances ensure fuel-efficient and conflict free descents to the metering gates at specified crossing times. In the terminal area, the Final Approach Spacing Tool (FAST) provides heading and speed advisories that help controllers produce an accurately spaced flow of aircraft on the final approach course. Data bases consisting of several hundred aircraft performance models, airline preferred operational procedures, and a three dimensional wind model support the operation of CTAS. The first component of CTAS, the Traffic Management Advisor, is being evaluated at the Denver TRACON and the Denver Air Route Traffic Control Center. The second component, the Final Approach Spacing Tool, will be evaluated in several stages at the Dallas/Fort Worth Airport beginning in October 1993. An initial stage of the Descent Advisor tool is being prepared for testing at the Denver Center in late 1994. Operational evaluations of all three integrated CTAS tools are expected to begin at the two field sites in 1995.

Erzberger, Heinz↗
NASA NTRS1982

An application of distributed processing - In the TDRSS ground communication fault isolation and monitoring system

A computer interface has been designed for the Fault Isolation and Monitoring System, a system providing qualitative and quantitative assessment of the communications between the Tracking and Data Relay Satellite System Ground Segment and NASA's Network Control Center. The functional requirements for the interface and the design philosophy are discussed, as are the methods and protocol used to implement the operator support software required to configure the monitoring system and to display and report the results of the analysis. The system relies on the use of intelligent terminals, with the human interface removed from the host computer.

Waddell, R. L., Jr.↗
NASA NTRS1998

Hypergravity exposure decreases gamma-aminobutyric acid immunoreactivity in axon terminals contacting pyramidal cells in the rat somatosensory cortex: a quantitative immunocytochemical image analysis

Quantitative evaluation of gamma-aminobutyric acid immunoreactivity (GABA-IR) in the hindlimb representation of the rat somatosensory cortex after 14 days of exposure to hypergravity (hyper-G) was conducted by using computer-assisted image processing. The area of GABA-IR axosomatic terminals apposed to pyramidal cells of cortical layer V was reduced in rats exposed to hyper-G compared with control rats, which were exposed either to rotation alone or to vivarium conditions. Based on previous immunocytochemical and behavioral studies, we suggest that this reduction is due to changes in sensory feedback information from muscle receptors. Consequently, priorities for muscle recruitment are altered at the cortical level, and a new pattern of muscle activity is thus generated. It is proposed that the reduction observed in GABA-IR of the terminal area around pyramidal neurons is the immunocytochemical expression of changes in the activity of GABAergic cells that participate in reprogramming motor outputs to achieve effective movement control in response to alterations in the afferent information.

Non-NASA Center↗
NASA NTRS1990

An imaging system for PLIF/Mie measurements for a combusting flow

The equipment required to establish an imaging system can be divided into four parts: (1) the light source and beam shaping optics; (2) camera and recording; (3) image acquisition and processing; and (4) computer and output systems. A pulsed, Nd:YAG-pummped, frequency-doubled dye laser which can freeze motion in the flowfield is used for an illumination source. A set of lenses is used to form the laser beam into a sheet. The induced fluorescence is collected by an UV-enhanced lens and passes through an UV-enhanced microchannel plate intensifier which is optically coupled to a gated solid state CCD camera. The output of the camera is simultaneously displayed on a monitor and recorded on either a laser videodisc set of a Super VHS VCR. This videodisc set is controlled by a minicomputer via a connection to the RS-232C interface terminals. The imaging system is connected to the host computer by a bus repeater and can be multiplexed between four video input sources. Sample images from a planar shear layer experiment are presented to show the processing capability of the imaging system with the host computer.

Wey, C. C.↗
NASA NTRS1988

Curvature of blended rolled edge reflectors at the shadow boundary contour

A technique is advanced for computing the radius of curvature of blended rolled edge reflector surfaces at the shadow boundary, in the plane perpendicular to the shadow boundary contour. This curvature must be known in order to compute the spurious endpoint contributions in the physical optics (PO) solution for the scattering from reflectors with rolled edges. The technique is applicable to reflectors with radially-defined rim-shapes and rolled edge terminations. The radius of curvature for several basic reflector systems is computed, and it is shown that this curvature can vary greatly along the shadow boundary contour. Finally, the total PO field in the target zone of a sample compact range system is computed and corrected using the shadow boundary radius of curvature, obtained using the technique. It is shown that the fields obtained are a better approximation to the true scattered fields.

Ellingson, S. W.↗
NASA NTRS1984

Interactive modeling using the PATRAN-G program

PATRAN-G is an interactive finite element generating and graphics display program. The program is currently executable on the VAX or PRIME computers and is compatible with 19 commercially available graphics terminals. The PATRAN program can be used in two modes: generation of a finite element model, or postprocessing of output data from a finite element analysis program. The finite element generating mode is divided into two phases. Phase I is the geometry construction. During this phase, the geometric boundaries of the model are defined and the material properties are input. Mirror imaging, translation and scaling of lines, surfaces, and volumes, and rotation of regions permit the geometry to be described efficiently. Points may be defined in alternate rectangular, cylindrical, or spherical coordinate systems. Also, PATRAN-G can calculate the intersection of lines or surfaces. This capability allows a user to easily model, for example, the intersection of a cylinder which cuts through a sphere at an angle. Once the geometry of the model has been described in terms of points, lines, surfaces, and volumes. Phase II is used to generate the computer finite element model.

Stalnaker, W. A.↗
NASA NTRS1971

Analysis of pilot warning indicator performance in terminal area traffic.

Three pilot warning indicator concepts for collision hazard avoidance are analyzed using computer fast-time simulation. A hazard measure is defined based on a 1/2-g maximum horizontal acceleration, a maximum climb or dive angle of 10 deg for each aircraft, and a 20-sec warning time, through escape completion. The traffic model is based on flight tracks recorded in the Atlanta terminal area over an 11 hr period during August 1967. The basic PWI concept studied alarms on range to flashing beacons mounted on intruder aircraft as a function of relative azimuth and elevation. The alarm-hazard epoch ratio is about 17/1 to maintain the missed-alarm rate below 10%. Beacon vignetting or range-rate discrimination are shown to reduce the false-alarm rate by about 75%.

Ruetenik, J. R.↗
NASA NTRS1983

Development and evaluation of a Kalman-filter algorithm for terminal area navigation using sensors of moderate accuracy

Translational state estimation in terminal area operations, using a set of commonly available position, air data, and acceleration sensors, is described. Kalman filtering is applied to obtain maximum estimation accuracy from the sensors but feasibility in real-time computations requires a variety of approximations and devices aimed at minimizing the required computation time with only negligible loss of accuracy. Accuracy behavior throughout the terminal area, its relation to sensor accuracy, its effect on trajectory tracking errors and control activity in an automatic flight control system, and its adequacy in terms of existing criteria for various terminal area operations are examined. The principal investigative tool is a simulation of the system.

Kanning, G.↗
NASA NTRS1983

A Kalman filter algorithm for terminal-area navigation with sensors of moderate accuracy

Translational state estimation in terminal area operations, using a set of commonly available position, air data, nd acceleration sensors, is described. Kalman filtering is applied to obtain maximum estimation occuracy from the sensors but feasibility in real-time computations requires a variety of approximations and devices aimed at minimizing the required computation time with only negligible loss of accuracy. Accuracy behavior throughout the terminal area, its relation to sensor accuracy, its effect on trajectory tracking errors and control activity in an automatic flight control system, and its adequacy in terms of existing criteria for various terminal area operations are examined. The principal investigative tool is a simulation of the system. Previously announced in STAR as N83-29193

Cicolani, L. S.↗
NASA NTRS1999

Wireless Augmented Reality Prototype (WARP)

Initiated in January, 1997, under NASA's Office of Life and Microgravity Sciences and Applications, the Wireless Augmented Reality Prototype (WARP) is a means to leverage recent advances in communications, displays, imaging sensors, biosensors, voice recognition and microelectronics to develop a hands-free, tetherless system capable of real-time personal display and control of computer system resources. Using WARP, an astronaut may efficiently operate and monitor any computer-controllable activity inside or outside the vehicle or station. The WARP concept is a lightweight, unobtrusive heads-up display with a wireless wearable control unit. Connectivity to the external system is achieved through a high-rate radio link from the WARP personal unit to a base station unit installed into any system PC. The radio link has been specially engineered to operate within the high- interference, high-multipath environment of a space shuttle or space station module. Through this virtual terminal, the astronaut will be able to view and manipulate imagery, text or video, using voice commands to control the terminal operations. WARP's hands-free access to computer-based instruction texts, diagrams and checklists replaces juggling manuals and clipboards, and tetherless computer system access allows free motion throughout a cabin while monitoring and operating equipment.

Devereaux, A. S.↗
NASA NTRS2010

Measurement of the Length of an Optical Trap

NASA Glenn has been involved in developing optical trapping and optical micromanipulation techniques in order to develop a tool that can be used to probe, characterize, and assemble nano and microscale materials to create microscale sensors for harsh flight environments. In order to be able to assemble a sensor or probe candidate sensor material, it is useful to know how far an optical trap can reach; that is, the distance beyond/below the stable trapping point through which an object will be drawn into the optical trap. Typically, to measure the distance over which an optical trap would influence matter in a horizontal (perpendicular to beam propagation) direction, it was common to hold an object in one optical trap, place a second optical trap a known distance away, turn off the first optical trap, and note if the object was moved into the second trap when it was turned on. The disadvantage of this technique is that it only gives information of trap influence distance in horizontal (x y) directions. No information about the distance of the influence of the trap is gained in the direction of propagation of the beam (the z direction). A method was developed to use a time-of-flight technique to determine the length along the propagation direction of an optical trap beam over which an object may be drawn into the optical trap. Test objects (polystyrene microspheres) were held in an optical trap in a water-filled sample chamber and raised to a pre-determined position near the top of the sample chamber. Next, the test objects were released by blocking the optical trap beam. The test objects were allowed to fall through the water for predetermined periods of time, at the end of which the trapping beam was unblocked. It was noted whether or not the test object returned to the optical trap or continued to fall. This determination of the length of an optical trap's influence by this manner assumes that the test object falls through the water in the sample chamber at terminal velocity for the duration of its fall, so that the distance of trap influence can be computed simply by: d = VTt, where d is the trap length (or distance of trap reach), VT is the terminal velocity of the test object, and t is the time interval over which the object is allowed to fall.

Wrbanek, Susan Y.↗
NASA NTRS1980

Microcomputer software development facilities

A more efficient and cost effective method for developing microcomputer software is to utilize a host computer with high-speed peripheral support. Application programs such as cross assemblers, loaders, and simulators are implemented in the host computer for each of the microcomputers for which software development is a requirement. The host computer is configured to operate in a time share mode for multiusers. The remote terminals, printers, and down loading capabilities provided are based on user requirements. With this configuration a user, either local or remote, can use the host computer for microcomputer software development. Once the software is developed (through the code and modular debug stage) it can be downloaded to the development system or emulator in a test area where hardware/software integration functions can proceed. The microcomputer software program sources reside in the host computer and can be edited, assembled, loaded, and then downloaded as required until the software development project has been completed.

Gorman, J. S.↗
NASA NTRS1972

Constructing and manipulating color imagery from digital data

The development of a multispectral scanner data analysis console is reported that incorporates a wideband tape unit, a teletypewriter, a digital computer, and color display as well as numeric display terminals. The device is able to digitize infrared scanner images and displays color differences according to signal differences between analog channels.

Davis, J. E.↗
NASA NTRS1979

Airborne East Coast/Midwest urban survey at 121.5/243 MHz

Results of an airborne RF interference measurement survey of the emergency-distress, Search and Rescue frequency bands at 121.5 and 243 MHz at an altitude of 25,000 ft over the U.S. East Coast and Midwest urban areas are presented. Included are a series of minutely median profile plots of antenna-noise temperature computed from RF interference power measurements at the output terminal of a quarter-wavelength monopole antenna, for both daytime and nighttime observations. The greatest value, 450,000 K, of minutely median temperature was recorded over New York City at 121.5 MHz during the day. East Coast urban areas exhibited a day-night effect at 121.5 MHz, where nighttime observations had a median value of 8.6-dB below daytime values; Midwest counterparts did not exhibit a significant day-night effect at 121.5 MHz.

Taylor, R. E.↗
NASA NTRS1982

Ensemble averaging of acoustic data

A computer program called Ensemble Averaging of Acoustic Data is documented. The program samples analog data, analyzes the data, and displays them in the time and frequency domains. Hard copies of the displays are the program's output. The documentation includes a description of the program and detailed user instructions for the program. This software was developed for use on the Ames 40- by 80-Foot Wind Tunnel's Dynamic Analysis System consisting of a PDP-11/45 computer, two RK05 disk drives, a tektronix 611 keyboard/display terminal, and FPE-4 Fourier Processing Element, and an analog-to-digital converter.

Stefanski, P. K.↗
NASA NTRS1983

ADAM: An Axisymmetric Duct Aeroacoustic Modeling system

An interconnected system of computer programs for analyzing the propagation and attenuation of sound in aeroengine ducts containing realistic compressible subsonic mean flows, ADAM was developed primarily for research directed towards the reduction of noise emitted from turbofan aircraft engines. The two basic components are a streamtube curvature program for determination of the mean flow, and a finite element code for solution of the acoustic propagation problem. The system, which has been specifically tailored for ease of use, is presently installed at NASA Langley Reseach Center on a Control Data Cyber 175 Computer under the NOS Operating system employing a Tektronix terminal for interactive graphics. The scope and organization of the ADAM system is described. A users guide, examples of input data, and results for selected cases are included.

Abrahamson, A. L.↗