Search NASA⌕ Search

SEARCH · Search NASA

Results for “Concentration gradients”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Springtime surface ozone fluctuations at high Arctic latitudes and their possible relationship to atmospheric bromine

At high Arctic stations such as Barrow, Alaska, springtime near-surface ozone amounts fluctuate between the highest and lowest values seen during the course of the year. Episodes when the surface ozone concentration is essentially zero last up to several days during this time of year. In the Arctic Gas and Aerosol Sampling Program (AGASP-I and AGASP-II) in 1983 and 1986, it was found that ozone concentrations often showed a very steep gradient in altitude with very low values near the surface. The cold temperatures, and snow-covered ground make it unlikely that the surface itself would rapidly destroy significant amounts of ozone. The AGASP aircraft measurements that found low ozone concentrations in the lowest layers of the troposphere also found that filterable excess bromine (the amount of bromine in excess of the sea salt component) in samples collected wholly or partially beneath the temperature inversion had higher bromine concentrations than other tropospheric samples. Of the four lowest ozone minimum concentrations, three of them were associated with the highest bromine enrichments. Surface measurements of excess filterable bromine at Barrow show a strong seasonal dependence with values rising dramatically early in March, then declining in May. The concentration of organic bromine gases such as bromoform rise sharply during the winter and then begin to decline after March with winter and early spring values at least three times greater than the summer minimum.

Oltmans, Samuel J.↗

Seasonal Characteristics of the Perennial Ice Cover of the Beaufort Sea

By definition, ice which survives the summer is classified as multiyear ice. Thus the area covered by multiyear ice during the winter should be nearly equivalent to the ice area during the previous summer's minima. This condition provides a reasonable criterion for the evaluation of ice concentration and ice type retrieval algorithms using remote-sensing data sets. From special sensor microwave imager (SSM/I) data the NASA Team algorithm estimates the multiyear, first-year, and total ice concentrations during the winter using combinations of the polarization and spectral gradient ratios. The Team algorithm provides only estimates of ice concentration in the summer. From ERS 1 synthetic aperture radar (SAR) data the remarkably stable contrast between multiyear ice and first-year ice in winter provides consistent estimates of multiyear ice concentrations. In the summer, multiyear ice concentration cannot be estimated from SAR or SSM/I data because free water on the surface effectively masks the backscatter and emissivity signature of this ice type. From SAR data a technique which takes advantage of the high backscatter of wind-roughened open water as a discrimination feature is used to estimate the total ice concentration in the summer. With a year-long (January 1992 to January 1993) data set from the Beaufort Sea we found that the multiyear ice concentration estimates from the SAR data are stable and are nearly equivalent to the ice concentration estimated at the end of the previous summer. We contrast this with the variability of the multiyear ice concentration and ice friction estimates obtained using SSM/I data. The Team algorithm produces ice concentration and multiyear ice estimates which are consistently lower than those from the SAR data. We discuss reasons for these discrepancies and the implications of the higher than previously noted multiyear ice concentrations.

Kwok, R.↗

Trends and Seasonal Variability of Atmospheric NO2 and HNO3 Concentrations Across Three Major African Biomes Inferred from Long-Term Series of Ground-Based and Satellite Measurements

In the framework of the INDAAF (International Network to study Deposition and Atmospheric chemistry in AFrica) programme, part of the ACTRIS (Aerosols, Clouds, and Trace gases Research InfraStructure), European Research Infrastructure for the long-term observation of Aerosol, Cloud, and Trace gases, this paper aims to study trends and seasonal variability of surface atmospheric NO2 and HNO3 concentrations, and OMI (Ozone Monitoring Instrument) NO2 over 6 sites in tropical Africa. Sites are located in west and central Africa to represent the major African biomes: dry savanna (Banizoumbou, Niger and Katibougou, Mali), wet savanna (Djougou, Benin and Lamto, Côte d’Ivoire) and forest (Bomassa, Republic of Congo and Zoétélé, Cameroon). Ground-based NO2 and HNO3 concentrations were obtained over the period 1998–2015 using INDAAF passive samplers at a monthly basis, and NO2 Vertical Column Densities (VCDs) from OMI for a 1-degree grid cell around each sites were obtained from 2005 to 2015. Mean annual NO2 concentrations ranged from 2.3 plus or minus 1.2 to 0.9 plus or minus 0.4 parts per billion (ppb) from dry savannas to forests, representing a north-south gradient. In dry savannas, we observe two concentration peaks of NO2 appearing at the beginning and the end of the wet season both for ground-based and satellite measurements, whereas at wet savannas and forest sites, NO2 concentrations are highest in the dry season. The seasonality of surface NO2 observations provide further evidence for a large role of microbial soil NOx emissions in dry savannas and of biomass burning NOx emissions in wet savanna and forest sites. Mean annual HNO3 concentrations ranged from 0.4 to 0.5 ppb in dry and wet savannas to 0.2 to 0.3 ppb in forest. In dry ecosystems, higher HNO3 concentrations are measured in the early wet season, consistent with NO2 results. The analysis of a long-term dataset of surface O3 concentrations indicates that HNO3 production can mainly be explained by the photo-oxidation of NOx. Mann-Kendall and Seasonal Kendall statistical tests showed that NO2 surface concentrations have a significant decreasing seasonal and annual trends at multiple sites (p-value less than 0.05) ranging from -2.96 percent per year (at Zoétélé) to -0.64 percent per year (at Banizoumbou). HNO3 results indicate no trends except at Bomassa (1.07 percent per year). The decreasing NO2 ground-based concentration trends observed in wet savannas sites are correlated with OMI NO2 decreasing trends at these sites. Trends obtained for NO2 concentrations in wet savanna and forest ecosystems are consistent with trends of NOₓ biomass burning emissions.

Trends↗

A Balloon-Borne Cloud Condensation Nuclei Counter

A balloon-borne instrument was constructed for observations of vertical profiles of cloud condensation nucleus (CCN) concentrations, active at 1% supersaturation. Droplet concentration in the static thermal-gradient diffusion chamber is deduced from the amount of scattered laser light detected by a photodetector. The photodetector is calibrated using a video camera and computer system to count the number of droplets produced from NaCl aerosol. Preliminary data are available from nine early morning profiles obtained at Laramie, Wyoming, between June 1995 and January 1997. To complement the CCN measurements, instruments that measure condensation nuclei (CN) and aerosols with diameter greater than 0.30 micrometers (D(sub 0.3) were also included on the balloon package. CCN concentrations exhibited a general decrease from the surface to the top of the boundary layers, were generally uniform through well-mixed layers, and show variability above well-mixed layers. In general, the structure of the CCN profile appears to be closely related to the structure in the CN and D(sub 0.3) profiles. Summer profiles generally have CCN concentration greater than 200/cu cm up to 500 mbar, whereas winter profiles are less than 200/cu cm at all levels.

Delene, David J.↗

Methane and nonmethane hydrocarbon concentrations in the Atlantic marine boundary layer

The reactions of reduced tropospheric trace gases with hydroxyl radicals are thought to play a significant role in global tropospheric photochemistry. Since tropospheric methane and nonmethane hydrocarbon (NMHC) concentrations will affect the tropospheric hydroxyl radical concentrations, accurate measurements of tropospheric CH4 and NMHC concentrations are necessary. Such measurements were, therefore, included in the first leg (from Hamburg, West Germany to Montevideo, Uruguay) of the 1980-1981 Antarctic Expedition. On the basis of the obtained data, a pronounced gradient between northern and southern hemispheric methane concentrations was observed in the marine boundary layer in the region of the intertropical convergence zone. Methane concentrations gradually decreased from about 1.70 ppmv at 40 deg N latitude to about 1.68 ppmv at 14 deg N latitude, then dropped sharply between 14 deg N and 10 deg N latitude to about 1.61 ppmv. NMHC data are also discussed.

Cofer, W. R., III↗

Dynamics of plankton populations in upwelling areas

The author has identified the following significant results. Spectral properties of the upwelled waters off the NW coast of Africa were studied with observations derived from aircraft and Skylab. Results indicate that the two-channel, ratio approach is ineffective in determining surface chlorophyll concentrations. Ocean color boundaries and temperature gradients were found to be directly correlated with each other and also with fishing effort in the upwelling region. Photographic and scanner data derived from Skylab were effective in locating ocean boundaries and mapping temperature distributions.

Szekielda, K. H.↗

Influence of peroxyacetyl nitrate (PAN) on odd nitrogen in the troposphere and lower stratosphere

Nonmethane hydrocarbon breakdown in the atmosphere produces aldehydes of which a fraction are transferred into peroxyacetyl nitrates (PAN) in the presence of NO and NO2. Since ethane is destroyed photochemically primarily above 1 km, PAN can be introduced into the upper troposphere and lower stratosphere without the need to be transported from the boundary layer where most hydrocarbons are destroyed and where PAN may be lost due to thermal decomposition and heterogeneous loss. Mixing ratios of ethane in the lower troposphere increase by a factor of 4-8 from equatorial to northern mid-latitudes. This difference is directly translatable into a PAN latitude gradient. At mid-latitudes the concentration of PAN below 20 km is 0.1 ppb comparable to and in some instances larger than predicted HO2NO2 mixing ratios. Like HO2NO2 and HNO3, PAN serves as a reservoir for odd nitrogen.

Aikin, A. C.↗

New Techniques for Studying Calcium Gradients

Improved techniques for detecting and manipulating spatial gradients of cytosolic free Ca(2+) concentrations (Ca(2)) sub i and intracellular stores are discussed. Three areas of progress are: (1) development of new fluorescent indicators for Ca(2+) that are the first to be suitable for measuring Ca(2+)) sub i and its inhomogeneities in individual cells; (2) invention of photolabile chelators which shift irreversibly from high to low affinity for Ca(2+) upon illumination, permitting light-controlled jumps in (Ca(2+)) sub i; and (3) fixation methods to trap dynamic intraorganellar Ca stores in a form readily visible by electron microscopy.

Tsien, R. Y.↗

Progress in integrated analysis with adaptive unstructured meshing

Design of lightweight structures and thermal protection systems for hypersonic vehicles depend on accurate prediction of aerothermal loads, structural temperatures and their gradients, and structural deformations and stresses. Concentration is on an alternative meshing technique which generates an entirely new adaptive unstructured mesh based on the solution obtained from the earlier mesh. The technique combined with the finite element method has been shown to significantly improve the efficiency and accuracy of the fluid, thermal, and structural analyses. Current capability of the adaptive unstructured meshing technique for the integrated fluid-thermal-structural analysis is described first. The technique was extended to transient thermal analysis of structures with time-dependent adaptive meshing to capture the detailed temperature response with a minimum number of unknowns and computational cost. Both linear and higher-order finite elements are implemented to demonstrate the generality of the technique and to investigate their solution accuracy. Currently, the adaptive meshing technique is being developed for plane structures that can be modeled with membrane elements and built-up structures modeled with membrane and bending elements. The capability of the technique to these different disciplinary problems is demonstrated by several examples.

Dechaumphai, Pramote↗

STS-78 Flight Day 5

On this fifth day of the STS-78 mission, the flight crew, Cmdr. Terence T. Henricks, Pilot Kevin R. Kregel, Payload Cmdr. Susan J. Helms, Mission Specialists Richard M. Linnehan, Charles E. Brady, Jr., and Payload Specialists Jean-Jacques Favier, Ph.D. and Robert B. Thirsk, M.D., are shown in the Spacelab conducting microgravity research. They concentrate on the use of the gradient furnace and the Bubble Drop Particle Unit to study process of manufacturing materials in microgravity, and on studies of human muscles and balance mechanisms. Also, Brady, Thirsk, Linnehan, and Favier conduct musculoskeletal tests that measure arm and hand-grip strength.

Source record↗

A Study of Oxidation of Hydrogen Based on Flashback of Hydrogen-Oxygen-Nitrogen Burner Flames

The flashback of hydrogen-oxygen-nitrogen flames was studied as a function of pressure, burner diameter, equivalence ratio, and oxidant strength. The results were treated on the assumption that the product of the critical boundary velocity gradient for flashback and the initial concentration of that reactant which is not in excess is proportional to a mean reaction rate associated with the flame zone. It was further assumed that this reaction rate can be expressed in terms of initial concentrations and flame temperature. Measurements at constant flame temperature yield orders of reaction with respect to hydrogen and oxygen. These do not vary with flame temperature. Measurements in which pressure is varied for several values of oxidant strength at constant equivalence ratio yield a total order of reaction and a function describing the dependence of the mean reaction rate on flame temperature. The total reaction order is independent of flame temperature and equal to the sum of the orders for hydrogen and oxygen. The dependence of the reaction rate on flame temperature cannot be described by a constant activation energy. The activation energy obtained apparently increases with flame temperature. Flashback results can be described by a single rate constant which is independent of equivalence ratio. Values were estimated for this rate constant as a function of flame temperature.

Fine, Burton D.↗

Navier-Stokes Aerodynamic Simulation of the V-22 Osprey on the Intel Paragon MPP

The paper will describe the Development of a general three-dimensional multiple grid zone Navier-Stokes flowfield simulation program (ENS3D-MPP) designed for efficient execution on the Intel Paragon Massively Parallel Processor (MPP) supercomputer, and the subsequent application of this method to the prediction of the viscous flowfield about the V-22 Osprey tiltrotor vehicle. The flowfield simulation code solves the thin Layer or full Navier-Stoke's equation - for viscous flow modeling, or the Euler equations for inviscid flow modeling on a structured multi-zone mesh. In the present paper only viscous simulations will be shown. The governing difference equations are solved using a time marching implicit approximate factorization method with either TVD upwind or central differencing used for the convective terms and central differencing used for the viscous diffusion terms. Steady state or Lime accurate solutions can be calculated. The present paper will focus on steady state applications, although time accurate solution analysis is the ultimate goal of this effort. Laminar viscosity is calculated using Sutherland's law and the Baldwin-Lomax two layer algebraic turbulence model is used to compute the eddy viscosity. The Simulation method uses an arbitrary block, curvilinear grid topology. An automatic grid adaption scheme is incorporated which concentrates grid points in high density gradient regions. A variety of user-specified boundary conditions are available. This paper will present the application of the scalable and superscalable versions to the steady state viscous flow analysis of the V-22 Osprey using a multiple zone global mesh. The mesh consists of a series of sheared cartesian grid blocks with polar grids embedded within to better simulate the wing tip mounted nacelle. MPP solutions will be shown in comparison to equivalent Cray C-90 results and also in comparison to experimental data. Discussions on meshing considerations, wall clock execution time, load balancing, and scalability will be provided.

Vadyak, Joseph↗

Pulmonary function in microgravity

We report the successful collection of a large quantity of human resting pulmonary function data on the SLS-1 mission. Preliminary analysis suggests that cardiac stroke volumes are high on orbit, and that an adaptive reduction takes at least several days, and in fact may still be in progress after 9 days on orbit. It also suggests that pulmonary capillary blood volumes are high, and remain high on orbit, but that the pulmonary interstitium is not significantly impacted. The data further suggest that the known large gravitational gradients of lung function have only a modest influence on single breath tests such as the SBN washout. They account for only approximately 25% of the phase III slope of nitrogen, on vital capacity SBN washouts. These gradients are only a moderate source of the cardiogenic oscillations seen in argon (bolus gas) and nitrogen (resident gas), on such tests. They may have a greater role in generating the normal CO2 oscillations, as here the phase relationship to argon and nitrogen reverses in microgravity, at least at mid exhalation in those subjects studied to date. Microgravity may become a useful tool in establishing the nature of the non-gravitational mechanisms that can now be seen to play such a large part in the generation of intra-breath gradients and oscillations of expired gas concentration. Analysis of microgravity multibreath nitrogen washouts, single breath washouts from more physiological pre-inspiratory volumes, both using our existing SLS-1 data, and data from the upcoming D-2 and SLS-2 missions, should be very fruitful in this regard.(ABSTRACT TRUNCATED AT 250 WORDS).

manned↗

Siderophilic Cyanobacteria: Implications for Early Earth.

Of all extant environs, iron-depositing hot springs (IDHS) may exhibit the greatest similarity to late Precambrian shallow warm oceans in regards to temperature, O2 gradients and dissolved iron and H2S concentrations. Despite the insights into the ecology, evolutionary biology, paleogeobiochemistry, and astrobiology examination of IDHS could potentially provide, very few studies dedicated to the physiology and diversity of cyanobacteria (CB) inhabiting IDHS have been conducted. Results. Here we describe the phylogeny, physiology, ultrastructure and biogeochemical activity of several recent CB isolates from two different greater Yellowstone area IDHS, LaDuke and Chocolate Pots. Phylogenetic analysis of 16S rRNA genes indicated that 6 of 12 new isolates examined couldn't be placed within established CB genera. Some of the isolates exhibited pronounced requirements for elevated iron concentrations, with maximum growth rates observed when 0.4-1 mM Fe(3+) was present in the media. In light of "typical" CB iron requirements, our results indicate that elevated iron likely represents a salient factor selecting for "siderophilicM CB species in IDHS. A universal feature of our new isolates is their ability to produce thick EPS layers in which iron accumulates resulting in the generation of well preserved signatures. In parallel, siderophilic CB show enhanced ability to etch the analogs of iron-rich lunar regolith minerals and impact glasses. Despite that iron deposition by CB is not well understood mechanistically, we recently obtained evidence that the PS I:PS II ratio is higher in one of our isolates than for other CB. Although still preliminary, this finding is in direct support of the Y. Cohen hypothesis that PSI can directly oxidize Fe(2+). Conclusion. Our results may have implications for factors driving CB evolutionary relationships and biogeochemical processes on early Earth and probably Mars.

Brown, I. I.↗

Brazing of Carbon Carbon Composites to Cu-clad Molybdenum for Thermal Management Applications

Advanced carbon carbon composites were joined to copper-clad molybdenum (Cu/Mo) using four active metal brazes containing Ti (Cu ABA, Cusin-1 ABA, Ticuni, and Ticusil) for potential use in thermal management applications. The brazed joints were characterized using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and Knoop microhardness measurements across the joint region. Metallurgically sound C-C/Cu/Mo joints, devoid of interfacial cracks formed in all cases. The joint interfaces were preferentially enriched in Ti, with Cu ABA joints exhibiting the largest interfacial Ti concentrations. The microhardness measurements revealed hardness gradients across the joint region, with a peak hardness of 300-350 KHN in Cusin-1 ABA and Ticusil joints and 200-250 KHN in Cu ABA and Ticuni joints, respectively.

Singh, M.↗

Analysis and Design of Crew Sleep Station for ISS

This paper details the analysis and design of the Temporary Sleep Station (TeSS) environmental control system for International Space Station (ISS). The TeSS will provide crewmembers with a private and personal space, to accommodate sleeping, donning and doffing of clothing, personal communication and performance of recreational activities. The need for privacy to accommodate these activities requires adequate ventilation inside the TeSS. This study considers whether temperature, carbon dioxide, and humidity within the TeSS remain within crew comfort and safety levels for various expected operating scenarios. Evaluation of these scenarios required the use and integration of various simulation codes. An approach was adapted for this study, whereby results from a particular code were integrated with other codes when necessary. Computational Fluid Dynamics (CFD) methods were used to evaluate the flow field inside the TeSS, from which local gradients for temperature, velocity, and species concentration such as CO (sub 2) could be determined. A model of the TeSS, containing a human, as well as equipment such as a laptop computer, was developed in FLUENT, a finite-volume code. Other factors, such as detailed analysis of the heat transfer through the structure, radiation, and air circulation from the TeSS to the US Laboratory Aisle, where the TeSS is housed, were considered in the model. A complementary model was developed in G189A, a code which has been used by NASA/JSC for environmental control systems analyses since the Apollo program. Boundary conditions were exchanged between the FLUENT and G189A TeSS models. G189A provides human respiration rates to the FLUENT model, while the FLUENT model provides local convective heat transfer coefficients to G189A model. An additional benefit from using an approach with both a systems simulation and CFD model, is the capability to verify the results of each model by comparison to the results of the other model. The G189A and FLUENT models were used to evaluate various ventilation designs for the TeSS over a range of operating conditions with varying crew metabolic load, equipment operating modes, ventilation flow rates, and with the TeSS doors open and closed. Results from the study were instrumental in the optimization of a design for the TeSS ventilation hardware. A special case was considered where failure of the TeSS ventilation system occurred. In this case, a study was conducted in order to determine the time required for the CO (sub 2) concentration inside the TeSS to increase to ISS limit values under transient conditions. A lumped-capacitance code, SINDA-FLUINT was used in this case to provide accurate predictions of the human reaction to the TeSS cabin conditions including core and skin temperatures and body heat storage. A simple two-dimensional CFD model of a crewmember inside the TeSS was developed in FLUENT in order to determine the volume envelope of the respired air from the human, which maintained a minimum velocity profile. This volume was then used in the SINDA-FLUINT model to facilitate the calculations of CO (sub 2) concentrations, dry bulb temperatures and humidity levels inside the TeSS.

Keener, John F.↗

Investigations on the Anthropogenic Reversal of the Natural Ozone Gradient Between Northern and Southern Midlatitudes

Our quantitative understanding of natural tropospheric ozone concentrations is limited by the paucity of reliable measurements before the 1980s. We utilize the existing measurements to compare the long-term ozone changes that occurred within the marine boundary layer at northern and southern midlatitudes. Since 1950 ozone concentrations have increased by a factor of 2.1 ± 0.2 in the Northern Hemisphere (NH) and are presently larger than in the Southern Hemisphere (SH), where only a much smaller increase has occurred. These changes are attributed to increased ozone production driven by anthropogenic emissions of photochemical ozone precursors that increased with industrial development. The greater ozone concentrations and increases in the NH are consistent with the predominant location of anthropogenic emission sources in that hemisphere. The available measurements indicate that this interhemispheric gradient was much smaller and was likely reversed in the pre-industrial troposphere with higher concentrations in the SH. Six Earth system model (ESM) simulations indicate similar total NH increases (1.9 with a standard deviation of 0.3), but they occurred more slowly over a longer time period, and the ESMs do not find higher pre-industrial ozone in the SH. Several uncertainties in the ESMs may cause these model–measurement disagreements: the assumed natural nitrogen oxide emissions may be too large, the relatively greater fraction of ozone injected by stratosphere–troposphere exchange to the NH may be overestimated, ozone surface deposition to ocean and land surfaces may not be accurately simulated, and model treatment of emissions of biogenic hydrocarbons and their photochemistry may not be adequate.

natural tropospheric ozone concentrations↗

Performance model of a recirculating stack nickel hydrogen cell

A theoretical model of the nickel hydrogen battery cell has been utilized to describe the chemical and physical changes during charge and overcharge in a recirculating stack nickel hydrogen cell. In particular, the movement of gas and electrolyte have been examined as a function of the amount of electrolyte put into the cell stack during cell activation, and as a function of flooding in regions of the gas screen in this cell design. Additionally, a two-dimensional variation on this model has been utilized to describe the effects of non-uniform loading in the nickel-electrode on the movement of gas and electrolyte within the recirculating stack nickel hydrogen cell. The type of nonuniform loading that has been examined here is that associated with higher than average loading near the surface of the sintered nickel electrode, a condition present to some degree in many nickel electrodes made by electrochemical impregnation methods. The effects of high surface loading were examined primarily under conditions of overcharge, since the movement of gas and electrolyte in the overcharging condition was typically where the greatest effects of non-uniform loading were found. The results indicate that significant changes in the capillary forces between cell components occur as the percentage of free volume in the stack filled by electrolyte becomes very high. These changes create large gradients in gas-filled space and oxygen concentrations near the boundary between the separator and the hydrogen electrode when the electrolyte fill is much greater than about 95 percent of the stack free volume. At lower electrolyte fill levels, these gaseous and electrolyte gradients become less extreme, and shift through the separator towards the nickel electrode. Similarly, flooding of areas in the gas screen cause higher concentrations of oxygen gas to approach the platinum/hydrogen electrode that is opposite the back side of the nickel electrode. These results illustrate the need for appropriate pore size distributions, and the maintenance of both convective electrolyte and gas flow paths through the stack, if the recirculating stack nickel hydrogen cell design is to work properly.

Zimmerman, Albert H.↗