Search NASA⌕ Search

SEARCH · Search NASA

Results for “Consequence - Focused Design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Concepts for the development of light-weight composite structures for rotor burst containment

Published results on rotor burst containment with single materials, and on body armor using composite materials were used to establish a set of hypotheses about what variables might control the design of a weight-efficient protective device. Based on modern concepts for the design and analysis of small optimum seeking experiments, a particular experiment for evaluating the hypotheses and materials was designed. The design and methods for the analysis of results are described. The consequence of such hypotheses is that the device should consist of as many as four concentric rings, each to consist of a material uniquely chosen for its position in the penetration sequence.

Holms, A. G.↗

Lateral forces induced by a misaligned roller

The magnitude of the lateral force induced by a roller, misaligned in its direction of travel is considered. Consequences of the induced lateral forces and examples of wheel suspension designs are given.

Mcginness, H.↗

Improved operation of magnetic bearings for flywheel energy storage system

Analysis and operation of prototype 500-Wh flywheel at low speeds have shown that many factors affect the correct functioning of the magnetic bearings. An examination is made of a number of these, including magnetic bearing control system nonlinearities and displacement transducer positioning, and their effects upon the successful operation of the suspension system. It is observed that the bearing control system is extremely sensitive to actuator parameters such as coil inductance. As a consequence of the analysis of bearing relaxation oscillations, the bearing actuator design methodology which has previously been used, where coil parameter selection is based upon static considerations, has been revised. Displacement transducer sensors which overcome the collocation problem are discussed.

Zmood, R. B.↗

Characterization and manufacture of braided composites for large commercial aircraft structures

Braided composite materials has been recognized as a potential cost effective material form for fuselage structural elements. Consequently, there is a strong need for more knowledge in the design, manufacture, test, and analysis of textile structural composites. Advance braided composite technology is advanced towards applications to a large commercial transport fuselage. The mechanics are summarized of materials and manufacturing demonstration results which were obtained in order to acquire an understanding of how braided composites can be applied to a commercial fuselage. Textile composites consisting of 2-D, 2-D triaxial, and 3-D braid patterns with thermoplastic and two resin transfer molding resin systems were studied. The structural performance of braided composites was evaluated through an extensive mechanical test program. Analytical methods were also developed and applied to predict the following: internal fiber architecture; stiffness; fiber stresses; failure mechanisms; notch effects; and the history of failure of the braided composite specimens. The applicability of braided composites to a commercial transport fuselage was further assessed through a manufacturing demonstration.

Fedro, Mark J.↗

Characterization and manufacture of braided composites for large commercial aircraft structures

Braided composite materials, one of the advanced material forms which is under investigation in Boeing's ATCAS program, have been recognized as a potential cost-effective material form for fuselage structural elements. Consequently, there is a strong need for more knowledge in the design, manufacture, test, and analysis of textile structural composites. The overall objective of this work is to advance braided composite technology towards applications to a large commercial transport fuselage. This paper summarizes the mechanics of materials and manufacturing demonstration results which have been obtained in order to acquire an understanding of how braided composites can be applied to a commercial fuselage. Textile composites consisting of 1D, 2D triaxial, and 3D braid patterns with thermoplastic and two RTM resin systems were investigated. The structural performance of braided composites was evaluated through an extensive mechanical test program. Analytical methods were also developed and applied to predict the following: internal fiber architectures, stiffnesses, fiber stresses, failure mechanisms, notch effects, and the entire history of failure of the braided composites specimens. The applicability of braided composites to a commercial transport fuselage was further assessed through a manufacturing demonstration. Three foot fuselage circumferential hoop frames were manufactured to demonstrate the feasibility of consistently producing high quality braided/RTM composite primary structures. The manufacturing issues (tooling requirements, processing requirements, and process/quality control) addressed during the demonstration are summarized. The manufacturing demonstration in conjunction with the mechanical test results and developed analytical methods increased the confidence in the ATCAS approach to the design, manufacture, test, and analysis of braided composites.

Fedro, Mark J.↗

The DAO Retrospective Data Assimilation System

The fixed-lag Kalman smoother of Cohn et al. (1994), or a version of a more computationally feasible approximation of it developed by Todling et al. (1998), is under implementation at the Data Assimilation Office (DAO) to build a retrospective data assimilation system (RDAS). The initial version of the RDAS uses the physical-space statistical analysis system and a modification of the incremental analysis update (IAU) procedure of Bloom et al. (1996); a follow up version of the RDAS Nill require the use of the adjoint of the DAO general circulation model (developed by Y. Yang and M Navon). The retrospective procedure is designed to produce improved analyses as well as improved assimilated fields consequently providing an improved climate representation through data assimilation.

Todling, Richardo↗

Partial Wave Analysis of Coupled Photonic Structures

The very high quality factors sustained by microcavity optical resonators are relevant to applications in wavelength filtering, routing, switching, modulation, and multiplexing/demultiplexing. Increases in the density of photonic elements require that attention be paid to how electromagnetic (EM) coupling modifies their optical properties. This is especially true when cavity resonances are involved, in which case, their characteristics may be fundamentally altered. Understanding the optical properties of microcavities that are near or in contact with photonic elements---such as other microcavities, nanostructures, couplers, and substrates---can be expected to advance our understanding of the roles that these structures may play in VLSI photonics, biosensors and similar device technologies. Wc present results from recent theoretical studies of the effects of inter- and intracavity coupling on optical resonances in compound spherical particles. Concentrically stratified spheres and bispheres constituted from homogeneous and stratified spheres are subjects of this investigation. A new formulation is introduced for the absorption of light in an arbitrary layer of a multilayered sphere, which is based on multiple reflections of the spherical partial waves of the Lorenz-Mie solution for scattering by a sphere. Absorption efficiencies, which can be used to profile cavity resonances and to infer fluorescence yields or the onset of nonlinear optical processes in the microcavities, are presented. Splitting of resonances in these multisphere systems is paid particular attention, and consequences for photonic device development and possible performance enhancements through carefully designed architectures that exploit EM coupling are considered.

Fuller, Kirk A.↗

The NASA Cold Land Processes Pathfinder Mission (CLPP)

The Cold Land Processes Pathfinder (CLPP) mission concept has been developed to measure hydrologic properties of the Cryosphere. The science driver for the mission is to understand the variability of global water cycling and its consequences for local water resources and climate. The CLPP mission is designed to reduce uncertainty of cold-region precipitation, storage, controls, and feedbacks to the land, atmosphere, and ocean, which in turn will improve prediction of future changes in water cycle dynamics. It will provide the first high-resolution global measurements of Earth's changing snow conditions to: 1) quantify the variability of processes in cold regions, 2) improve understanding of past changes, and 3) enable breakthroughs in prediction of future water resources, weather, and climate. The CLPP concept consists of active (C- and Ku-band) and passive (K- and Ka-band) microwave sensors (with high and moderate spatial resolution respectively) to observe snow water equivalent and snow wetness at local process scales. The CLPP global sampling framework provides necessary capability to relate observed local scale snow characteristics to atmospheric forcings, improve predictive models operating at multiple scales, and to tie the short-term CLPP record to the long-term low-resolution remote sensing climate record of global snow properties.

Cline, D.↗

Influence of Combined Whole-Body Vibration Plus G-Loading on Visual Performance

Recent engineering analyses of the integrated Ares-Orion stack show that vibration levels for Orion crews have the potential to be much higher than those experienced in Gemini, Apollo, and Shuttle vehicles. Of particular concern to the Constellation Program (CxP) is the 12 Hz thrust oscillation (TO) that the Ares-I rocket develops during the final ~20 seconds preceding first-stage separation, at maximum G-loading. While the structural-dynamic mitigations being considered can assure that vibration due to TO is reduced to below the CxP crew health limit, it remains to be determined how far below this limit vibration must be reduced to enable effective crew performance during launch. Moreover, this "performance" vibration limit will inform the operations concepts (and crew-system interface designs) for this critical phase of flight. While Gemini and Apollo studies provide preliminary guidance, the data supporting the historical limits were obtained using less advanced interface technologies and very different operations concepts. In this study, supported by the Exploration Systems Mission Directorate (ESMD) Human Research Program, we investigated display readability-a fundamental prerequisite for any interaction with electronic crew-vehicle interfaces-while observers were subjected to 12 Hz vibration superimposed on the 3.8 G loading expected for the TO period of ascent. Two age-matched groups of participants (16 general population and 13 Crew Office) performed a numerical display reading task while undergoing sustained 3.8 G loading and whole-body vibration at 0, 0.15, 0.3, 0.5, and 0.7 g in the eyeballs in/out (x-axis) direction. The time-constrained reading task used an Orion-like display with 10- and 14-pt non-proportional sans-serif fonts, and was designed to emulate the visual acquisition and processing essential for crew system monitoring. Compared to the no-vibration baseline, we found no significant effect of vibration at 0.15 and 0.3 g on task error rates (ER) or response times (RT). Significant degradations in both ER and RT, however, were observed at 0.5 and 0.7 g for 10-pt, and at 0.7 g for 14-pt font displays. These objective performance measures were mirrored by participants' subjective ratings. Interestingly, we found that the impact of vibration on ER increased with distance from the center of the display, but only for vertical displacements. Furthermore, no significant ER or RT aftereffects were detected immediately following vibration, regardless of amplitude. Lastly, given that our reading task required no specialized spaceflight expertise, our finding that effects were not statistically distinct between our two groups is not surprising. The results from this empirical study provide initial guidance for evaluating the display readability trade-space between text-font size and vibration amplitude. However, the outcome of this work should be considered preliminary in nature for a number of reasons: 1. The single 12 Hz x-axis vibration employed was based on earlier load-cycle models of the induced TO environment at the end of Ares-I first stage flight. Recent analyses of TO mitigation designs suggest that significant concurrent off-axis vibration may also occur. 2. The shirtsleeve environment in which we tested fails to capture the full kinematic and dynamic complexity of the physical interface between crewmember and the still-to-bematured helmet-suit-seat designs, and the impact these will have for vibration transmission and consequent performance. 3. By examining performance in this reading and number processing task, we are only assessing readability, a first and necessary step that in itself does not directly address the performance of more sophisticated operational tasks such as vehicle-health monitoring or manual control of the vehicle.

readability↗

Analysis of the Accuracy of Actuation Electronics in the Laser Interferometer Space Antenna Pathfinder

The Laser Interferometer Space Antenna Pathfinder (LPF) main observable, labelled∆g, is the differential force per unit mass acting on the two test masses in free fall condition, after the contribution of all non-gravitational forces have been compensated. At low frequencies the differential force is compensated by an applied electrostatic actuation force,which then must be subtracted from the measured acceleration to obtain∆g. Any inaccuracy in the actuation force contaminates the residual acceleration. This study investigates the accuracy of the electrostatic actuation system and its impact on the LPF main observable. It is shown that the inaccuracy is mainly caused by the rounding errors in the waveform processing and also by the random error caused by the analog to digital converter (ADC) random noise in the control loop. Both errors are one order of magnitude smaller than the resolution of the commanded voltages. We developed a simulator based on the LPF design to compute the close-to-reality actuation voltages and consequently, the resulting actuation forces. The simulator is applied in post-processing the LPF data.

M. Armano↗

NASA Environmental Control and Life Support Technology Development for Exploration: 2021 to 2022 Overview

Over the past year, significant progress has occurred in technology development, ground testing, and ISS technology demonstrations within the NASA Environmental Control and Life Support (ECLSS) community. This paper provides a technology development update in the following capability areas: life support, environmental monitoring, fire safety, and logistics. Technologies for exploration missions must be reliable in their operation which support crewed mission phases. However, they also need to be put into a reduced use or dormant states to support uncrewed mission phases and then successfully and reliably returned to a nominal state to support crew. Multi-year demonstration of systems operation across this range of conditions are essential to mission success. Project overviews will include how the current activity supports the goal of multi-year demonstrations, planned follow-on activities, and what type of exploration mission elements are targeted for infusion. Technologies must be demonstrated and validated early enough to inform early exploration element milestone reviews (mission concept reviews, systems requirement reviews and no later than preliminary design reviews) so that supporting vehicle systems can also be matured. Consequently, for low technology readiness activities, it is important to also identify which mission elements they might infuse into and how they may offer potential operational, dormancy, or mass benefits. While low TRL technology timelines may not support initial mission needs, early infusion is still reasonable with sufficient testing to validate performance and reliability.

Life Support↗

Understanding Fundamental Mechanisms Behind Anomalous Segregation Behavior at Grain Boundaries during Diffusional Creep

Recent experimental studies in a nickel (Ni)-rhenium (Re) alloy demonstrated anisotropic elemental segregation around grain boundaries (GBs) while under tensile strain. Some GBs showed Re enrichment, while others showed Re depletion. We hypothesize that differing vacancy fluxes to GBs, caused by the anisotropic elastic stresses generated within the polycrystal, results in anisotropic creep-induced segregation (CIS) and grain growth. Using molecular dynamics simulations, we developed a mechanistic understanding of CIS and determined the contribution of elastic stresses and grain growth in Ni-Re alloys. We find that the stress state of the GB significantly changes the segregation energy profile for Re atoms, leading to significant Re redistribution. Further, as the GB migrates, the segregation/desegregation tendency of Re leads to bands of Re enrichment/depletion. Our results have important consequences for the quantitative predictions of diffusion creep and for the design of high-temperature creep-resistant Ni alloys.

36 - MATERIALS SCIENCE↗

Solvated Electrons Have Multiple Personalities in Molten Salts

P-Crosscut: Solvated Electrons Have Multiple Personalities in Molten Salts [EFRC – MSEE] Alejandro Ramos-Ballesteros;1 Hung H. Nguyen;2 Kazuhiro Iwamatsu;3 Santanu Roy;4 Vyacheslav Bryantsev;4 Michael E. Woods;1 Ruchi Gakhar;1 Phillip Halstenberg;4 Bobby Layne;5 Jay A. LaVerne;6 Claudio J. Margulis:2* and James F. Wishart5* 1Idaho National Laboratory; 2The University of Iowa; 3Hunter College; 4Oak Ridge National Laboratory; 5Brookhaven National Laboratory; 6University of Notre Dame Abstract: The solvated (eS–) is a powerful reducing agent and one of the primary products of molten salt radiolysis. In these extreme high-temperature environments, the eS– can initiate cascades of redox processes that significantly alter the physical and chemical properties of a molten salt, posing challenges for molten salt reactor (MSR) performance and longevity. Consequently, mastering the fundamental behavior of the eS– could enable the design of specific molten salt mixtures with tailored Lewis acidities for controlling the speciation and chemical reactivity of the eS–, thereby mitigating its overall impact on MSR technologies. Here, we use time-resolved electron pulse radiolysis techniques for determining chemical kinetics and transient absorption spectra, combined with ab initio molecular dynamics simulations to explore the influence of multivalent metal cations on the fundamental speciation and distribution of eS– coordination environments.

38 - RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCL↗

Design and Test of Mixed-flow Impellers IV : Experimental Results for Impeller Models MFI-1 and MFI-2 with Changes in Blade Height

Modifications A and B of impeller model MFI-1 and A, B, and C of impeller model MFI-2 were investigated experimentally in an attempt to determine what allowance in blade height should be made for boundary layer and viscous losses in an impeller designed for isentropic compressible flow. A gradual increase in blade height was arbitrarily made from inlet to outlet in anticipation of a gradual build-up of boundary layer. Apparently there was a rapid build-up of boundary layer near the inlet in the experimental case rather than a gradual one. Therefore, the proper allowance for boundary layer cannot be described from the data obtained. Decreasing the pressure gradient along the shroud by reducing the blade height allowance apparently did little to increase the overall efficiency. At the design speed of 1400 feet per second, the overall adiabatic efficiency was increased from 0.83 for the MFI-1A to 0.85 for the MFI-1B with reduction in height; however, it is indicated from the theoretical velocity distribution and outlet surveys that the increase was due to a change from decelerating to accelerating flow along the hub rather than from any change along the shroud. It is further indicated that the consequences of a thickened or separated boundary layer depend not only on the design velocity gradients but also on the shape of the passage.

Hamrick, Joseph T↗

Antenna Beam Coverage Concepts

The strawman Personal Access Satellite System (PASS) design calls for the use of a CONUS beam for transmission between the supplier and the satellite and for fixed beams for transmission between the basic personal terminal and the satellite. The satellite uses a 3 m main reflector for transmission at 20 GHz and a 2 m main reflector for reception at 30 GHz. There are several types of spot beams under consideration for the PASS system besides fixed beams. The beam pattern of a CONUS coverage switched beam is shown along with that of a scanning beam. A switched beam refers to one in which the signal from the satellite is connected alternatively to various feed horns. Scanning beams are taken to mean beams whose footprints are moved between contiguous regions in the beam's coverage area. The advantages and disadvantages of switched and/or scanning beams relative to fixed beams. The consequences of using switched/scanning in lieu of fixed beams in the PASS design and attempts are made to evaluate the listed advantages and disadvantages. Two uses of switched/scanning beams are examined. To illustrate the implications of switched beams use on PASS system design, operation at two beam scan rates is explored.

Estabrook, Polly↗

Rover technology for manned Mars missions

A set of roving vehicle design requirements were postulated, corresponding to an idealized Mars transport vehicle operational scenario which could serve as a reference for a manned Mars mission. The ability of conventional vehicles to satisfy these requirements were examined. The study indicated that no conventional vehicle could satisfy all of the requirements, as the vehicles are presently configured. Consequently, the requirements have to either be relaxed and/or an alternative, less conventional vehicle design will have to be developed. A possible unconventional vehicle design which has received considerable attention for DARPA and the Army is the walker vehicle. The design issues associated with this vehicle are presented, along with a comparison of the performance capabilities of this technology vs. conventional vehicle technology.

Gail Klein↗

Refinement of the Transition-edge Sensor Design for ATHENA X-IFU

The X-ray Integral Field Unit (X-IFU) instrument on the Advanced Telescope for High ENergy Astrophysics (ATHENA) is baselined to have 2376 transition-edge sensor (TES) microcalorimeter pixels in a single array. The required performance for X-IFU has been demonstrated on a kilo-pixel array of square TES’s with 50 m side length, and this is considered the baseline pixel design. However, over the last few years we have explored small modifications to this design in search of a globally optimized instrument performance. We have previously reported on investigations of extending the length of the TES’s and variations in the number of X-ray absorber support stems. Here we report on investigations of TES designs with a length of 50 m but narrower width. We will discuss the consequence of this on magnetic field sensitivity, resistive transition parameters, spectral performance, and ease of multiplexing. We will also discuss how the number and position of the absorber attachments influences the vibrational modes of the pixels, and the impact this may have on performance. Finally, we will present measurements of more substantial change options of our TES design, including more extreme TES geometries, the use of metal islands or etched holes in the silicon nitride membranes, and the position of wiring to minimize current-induced magnetic field effects. The exploration of all these changes to the design are not only useful for optimizing performance on X-IFU, but also guide our fundamental understanding of the key physics of TES microcalorimeters.

Nick Wakeham↗

ILAW Container Cost Reduction and Optimization Study

This study, performed on behalf of Washington River Protection Solutions (WRPS), examines the potential for making cost savings for the Immobilized Low Active Waste (ILAW) containers over the mission life of the Waste Treatment and Immobilization Plant (WTP). it builds on earlier study assessments 24590-LAW-RPT-M-01-001 Rev 0 ILAW Product Container Specifications Optimization Study and DOE/ORP-2013-02 Rev 0 Decision Analysis of Low-Active Waste Container Finishing Handling System Alternatives. The WTP design and installed equipment has evolved over an extended period ~20 years. Consequently, some of the existing requirements relating the ILAW containers may no longer be applicable under current mission plans where the glass filled containers are placed into the Integrated Disposal Facility (IDF) rather than stacked in an engineered purpose-built ventilated store as originally envisioned. The study team reviewed available WTP project reference documents to establish the functions the container must perform and assign requirements against each of these functions. With the assumptions that some of the existing WTP contract restrictions would not necessarily apply to the subsequent facility operations contract the container requirements were reviewed to identify those which were ‘hard constraints‘, imposed by regulatory requirements. Initially each of these hard constraints were reviewed, evaluated and documented to see if they precluded the use of an alternate less expensive material of construction, carbon steel, to the existing 304 L stainless steel in the current container specification. That review did not generate any fatal flaws for a change in material of construction to carbon steel allowing the study team to examine the impacts of material cost savings, potential changes to the design and requirements and impacts on interfaces of the containers with the existing WTP process equipment from container receipt, transfers, glass filling, cooling and export. In addition, a change in container target fill level was evaluated and qualitative, and quantitative where feasible, impacts to the container fabrication process assessed. Lastly, additional follow on development or testing activities to support the use of carbon steel were assessed and a recommended path forward with a ROM cost and timescale developed.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗