Search NASA⌕ Search

SEARCH · Search NASA

Results for “D”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Solar photolysis of ozone to singlet D oxygen atoms

The ground-level photolysis frequency of ozone J(O3) to produce metastable singlet D oxygen atoms (O (D-1)) is measured using a novel instrumental technique involving electrical conductivity. The O(D-1) atoms produced react with nitrous oxide (N2O) carrier gas to form higher oxides of nitrogen (NO(x)). These oxides were detected by mixing with methanol and determining the increase in electrical conductivity with a continuous-flow dual conductivity cell. Over 70 days of data were collected under varying sky conditions. The effect of temperature on J(O3) was measured. The results agree with model predictions. The effects of atmospheric aerosols, changes in overhead ozone column, and local cloudiness are discussed.

Blackburn, Thomas E.↗
NASA NTRS1993

A multiple-mode three-dimensional model of VLF propagation in the earth-ionosphere waveguide in the presence of localized D region disturbances

Transient localized D region disturbances, such as those associated with lightning discharges, affect the characteristics of VLF waves propagating in the Earth-ionosphere waveguide. In particular, both phase and amplitude changes in the subionospheric signal can be observed at receiving sites as a result of the wave scattering that takes place in the disturbed region. In the present paper we present a multiple-mode three-dimensional model of VLF propagation in the Earth-ionosphere waveguide in the presence of localized D region disturbances. The model takes into account great circle (GC) propagation paths with realistic ground and ionospheric conductivity changes that result in mode conversion along the path. It is assumed that conductivity changes transverse to the GC paths are negligible except in the vicinity of the D region disturbance and that mode coupling is negligible within the disturbed region. This new model is applied to experimental observations and is found to be in general agreement. The diagnostics potential of the model for characterizing energetic particle precipitation events is discussed.

Poulsen, William L.↗
NASA NTRS1993

Collision cross sections and diffusion parameters for H and D in atomic oxygen

Modeling the behavior of H and D in planetary exospheres requires detailed knowledge of the differential scattering cross sections for all of the important neutral-neutral and ion-neutral collision processes affecting these species over their entire ranges of interaction energies. In the upper atmospheres of Earth, Venus, and other planets as well, the interactions of H and D with atomic oxygen determine the rates of diffusion of escaping hydrogen isotopes through the thermosphere, the velocity distributions of exospheric atoms that encounter the upper thermosphere, the lifetimes of exospheric orbiters with periapsides near the exobase, and the transfer of momentum in collisions with hot O. The nature of H-O and D-O collisions and the derivation of a data base consisting of phase shifts and the differential, total, and momentum transfer cross sections for these interactions in the energy range 0.001 - 10 eV are discussed. Coefficients of mutual diffusion and thermal diffusion factors are calculated for temperatures of planetary interest.

Hodges, R. R., Jr.↗
NASA NTRS1991

A 3-D nonlinear recursive digital filter for video image processing

This paper introduces a recursive 3-D nonlinear digital filter, which is capable of performing noise suppression without degrading important image information such as edges in space or time. It also has the property of unnoticeable bandwidth reduction immediately after a scene change, which makes the filter an attractive preprocessor to many interframe compression algorithms. The filter consists of a nonlinear 2-D spatial subfilter and a 1-D temporal filter. In order to achieve the required computational speed and increase the flexibility of the filter, all of the linear shift-variant filter modules are of the IIR type.

Bauer, P. H.↗
NASA NTRS1990

Depth-viewing-volume increase by collimation of stereo 3-D displays

Typical stereo 3-D displays are produced using a single-image-source, which is time-multiplexed, to present disparate, directly-viewed views (stereo pairs) of the visual scene to each eye. However, current stereoscopic viewing techniques impose severe restrictions in the effective viewing-volume of the stereo 3-D display. Recent experiments at Langley Research Center determined that the effective region of stereopsis cuing, the depth-viewing volume, increased with increasing viewer-to-screen distances. This increase was also accompanied by a decrease in the field-of-view of the system. It was postulated that collimation of the display source would dramatically increase the depth-viewing volume, as the effective accommodation distance would be near infinity, while maintaining the field-of-view at required levels. The goal of this proof-of-concept effort was to investigate whether or not a dramatic increase in depth-viewing volume for stereo 3-D displays would be provided by the application of collimated optics to the stereo display source.

Busquets, Anthony M.↗
NASA NTRS1985

Application of AVHRR vegetation index to study atmosphere-biosphere exchange of CO2: Results from a 3-D tracer transport model

The 'normalized difference vegetation indices' (NVI) derived from AVHRR radiances are combined with field data of soil respiration and a global map of net primary productivity to prescribe, for the globe, the seasonal exchange of CO2 between the atmosphere and the terrestrial biosphere. The monthly fluxes of CO2 thus obtained are used as inputs to a 3-D tracer transport model which uses winds generated by a 3-D atmospheric general circulation model to advect CO2 as an inert constituent. Analysis of the 3-D model results shows reasonable agreement between the simulated and observed annual cycles of atmospheric CO2 at the locations of the remote monitoring stations. The application is shown of atmospheric CO2 distributions to calibrate the NVI in terms of carbon fluxes. The approach suggests that the NVI may be used to provide quantitative information about long term and global scale variations of photosynthetic activity and of atmospheric CO2 concentrations provided that variations in the atmospheric circulation and in atmospheric composition are known.

Fung, Inez Y.↗
NASA NTRS1993

Laser ranging network performance and routine orbit determination at D-PAF

ERS-1 is now about 8 months in orbit and has been tracked by the global laser network from the very beginning of the mission. The German processing and archiving facility for ERS-1 (D-PAF) is coordinating and supporting the network and performing the different routine orbit determination tasks. This paper presents details about the global network status, the communication to D-PAF and the tracking data and orbit processing system at D-PAF. The quality of the preliminary and precise orbits are shown and some problem areas are identified.

Massmann, Franz-Heinrich↗
NASA NTRS1993

Determining the 3-D structure and motion of objects using a scanning laser range sensor

In order for the EVAHR robot to autonomously track and grasp objects, its vision system must be able to determine the 3-D structure and motion of an object from a sequence of sensory images. This task is accomplished by the use of a laser radar range sensor which provides dense range maps of the scene. Unfortunately, the currently available laser radar range cameras use a sequential scanning approach which complicates image analysis. Although many algorithms have been developed for recognizing objects from range images, none are suited for use with single beam, scanning, time-of-flight sensors because all previous algorithms assume instantaneous acquisition of the entire image. This assumption is invalid since the EVAHR robot is equipped with a sequential scanning laser range sensor. If an object is moving while being imaged by the device, the apparent structure of the object can be significantly distorted due to the significant non-zero delay time between sampling each image pixel. If an estimate of the motion of the object can be determined, this distortion can be eliminated; but, this leads to the motion-structure paradox - most existing algorithms for 3-D motion estimation use the structure of objects to parameterize their motions. The goal of this research is to design a rigid-body motion recovery technique which overcomes this limitation. The method being developed is an iterative, linear, feature-based approach which uses the non-zero image acquisition time constraint to accurately recover the motion parameters from the distorted structure of the 3-D range maps. Once the motion parameters are determined, the structural distortion in the range images is corrected.

Nandhakumar, N.↗
NASA NTRS1994

Overview of the NASA balloon R&D program

The catastrophic balloon failure during the first half of the 1980's identified the need for a comprehensive and continuing balloon research and development (R&D) commitment by NASA. Technical understanding was lacking in many of the disciplines and processes associated with scientific ballooning. A comprehensive balloon R&D plan was developed in 1986 and implemented in 1987. The objectives were to develop the understanding of balloon system performance, limitations, and failure mechanisms. The program consisted of five major technical areas: structures, performance and analysis, materials, chemistry and processing, and quality control. Research activitites have been conducted at NASA/Goddard Space Flight Center (GSFC)-Wallops Flight Facility (WFF), other NASA centers and government facilities, universities, and the balloon manufacturers. Several new and increased capabilities and resources have resulted from this activity. The findings, capabilities, and plan of the balloon R&D program are presented.

Smith, I. Steve, Jr.↗
NASA NTRS1993

Sounder stimulated D(sub n) resonances in Jupiter's Io plasma torus

On February 8, 1992, the Ulysses spacecraft passed through Jupiter's Io plasma torus, where rich spectra of narrow-band resonances were stimulated by the relaxation sounder of the Ulysses unified radio and plasma wave (URAP) instrument. Since the gyrofrequency f(sub g) is comparable to the plasma frequency f(sub p) in the Io torus, it was predicted that the general classification of stimulated ionospheric D(sub n) resonances, developed for 1 is less than or equal to f(sub p)/f(sub g) is less than or equal to 8 in the Earth's topside ionosphere, should apply in the Io torus as well as the Earth's magnetosphere (Osherovich, 1989). The URAP plasmagrams (sounder spectra) in the portions of the Io torus satisfying these plasma conditions are dominated by the D(sub n) resonances for frequencies below f(sub p). On most of these plasmagrams the f(sub p) resonance is also present, but it is seldom the dominant resonance. Neither upper hybrid nor nf(sub g) resonances have been found on these plasmagrams. The identification of D(sub n) resonances has allowed both the electron density and the magnetic field amplitude to be calculated. The derived densities on the outbound pass agree well with a Voyager model of Bagenal (1992). The derived magnetic field values are close to the Goddard Space Flight Center O(sub 6) magnetic field model.

Osherovich, V. A.↗
NASA NTRS1995

A 3-D Navier-Stokes CFD study of turbojet/ramjet nozzle plume interactions at Mach 3.0 and comparison with data

Advanced airbreathing propulsion systems used in Mach 4-6 mission scenarios, usually consist of a single integrated turboramjet or as in this study, a turbojet housed in an upper bay with a separate ramjet housed in a lower bay. As the engines transition from turbojet to ramjet, there is an operational envelope where both engines operate simultaneously. One nozzle concept under consideration has a common nozzle, where the plumes from the turbojet and ramjet interact with one another as they expand to ambient conditions. In this paper, the two plumes interact at the end of a common 2-D cowl, when they both reach an approximate Mach 3.0 condition and then jointly expand to Mach 3.6 at the common nozzle exit plane. At this condition, the turbojet engine operated at a higher NPR than the ramjet, where the turbojet overpowers the ramjet plume, deflecting it approximately 12 degrees downward and in turn the turbojet plume is deflected 6 degrees upward. In the process, shocks were formed at the deflections and a shear layer formed at the confluence of the two jets. This particular case was experimentally tested and the data used to compare with the PARC3D code with k-kl two equation turbulence model. The 2-D and 3-D centerline CFD solutions are in good agreement, but as the CFD solutions approach the outer sidewall, a slight variance occurs. The outer wall boundary layers are thin and do not present much of an interaction, however, where the confluence interaction shocks interact with the thin boundary layer on the outer wall, strong vortices run down each shock causing substantial disturbances in the boundary layer. These disturbances amplify somewhat as they propagate downstream axially from the confluence point. The nozzle coefficient (CFG) is reduced 1/2 percent as a result of this sidewall interaction, from 0.9850 to 0.9807. This three-dimensional reduction is in better agreement with the experimental value of 0.9790.

Chang, Ing↗
NASA NTRS1995

Panoramic, large-screen, 3-D flight display system design

The report documents and summarizes the results of the required evaluations specified in the SOW and the design specifications for the selected display system hardware. Also included are the proposed development plan and schedule as well as the estimated rough order of magnitude (ROM) cost to design, fabricate, and demonstrate a flyable prototype research flight display system. The thrust of the effort was development of a complete understanding of the user/system requirements for a panoramic, collimated, 3-D flyable avionic display system and the translation of the requirements into an acceptable system design for fabrication and demonstration of a prototype display in the early 1997 time frame. Eleven display system design concepts were presented to NASA LaRC during the program, one of which was down-selected to a preferred display system concept. A set of preliminary display requirements was formulated. The state of the art in image source technology, 3-D methods, collimation methods, and interaction methods for a panoramic, 3-D flight display system were reviewed in depth and evaluated. Display technology improvements and risk reductions associated with maturity of the technologies for the preferred display system design concept were identified.

Franklin, Henry↗
NASA NTRS1996

(Re)inventing Government-Industry R and D Collaboration

This paper describes the lessons learned in developing and operating a large-scale strategic alliance whose organization and coordination is U.S. Government-led using new means for R&D collaboration. Consortia in the United States counter a century of 1884 Sherman Anti-Trust Law-based governmental and legal policy and a longstanding business tradition of unfettered competition. Success in public-private collaboration in America requires compelling vision and motivation by both partners to reinvent our ways of doing business. The foundations for reinventing government and alliance building were laid in 1994 with Vice President Al Gore's mandates for Federal Lab Reviews and other examinations of the roles and missions for the nation's more than 700 government labs. In addition, the 1984 National Cooperative Research Act (NCRA) set in motion the abilities for U.S. companies to collaborate in pre-competitive technology development. The budget realities of the 1990's for NASA and other government agencies demand that government discover the means to accomplish its mission by leveraging resources through streamlining as well as alliances. Federal R&D investments can be significantly leveraged for greater national benefit through strategic alliances with industry and university partners. This paper presents early results from one of NASA's first large-scale public/private joint R&D ventures.

Holmes, Bruce J.↗
NASA NTRS1998

Onset on Ice Stream D, West Antarctica

Surface flow in a 10,000 sq km area of the onset area of ice stream D was measured by repeat, precise GPS (Global Positioning System) surveys over a one-year interval. The pattern of velocity and strain rate illustrates the development of ice stream D. The major flow into D originates south of Byrd Station. Using flow parameters derived by assuming ice at Byrd is not sliding, the deformation component of velocity at all grid locations was calculated using the local ice thickness and a surface slope averaged over 40 km (-20 ice thicknesses). The results imply that ice entering the grid from its upstream boundary is already sliding. However, calculation of the relationship between the driving stress, the ice thickness and the velocity shows that the developing ice stream is very different from ice at Byrd Station, possibly due to warmer effective ice temperatures or a different rheology.

Bindschadlar, Robert↗
NASA NTRS1998

3-D Modeling of Directional Solidification of a Non-Dilute Alloy with Temperature and Concentration Fields Coupling via Materials Properties Dependence and via Double Diffusive Convection

Numerical simulation of the HgCdTe growth by the vertical Bridgman method was performed using FIDAP finite element code. Double-diffusive melt convection is analyzed, as the primary factor at controls inhomogeneity of the solidified material. Temperature and concentration fields in the model are also coupled via material properties, such as thermal and solutal expansion coefficients with the dependence on both temperature and concentration, and melting temperature evaluation from pseudobinary CdTe-HgTe phase diagram. Experimental measurements were used to obtain temperature boundary conditions. Parametric study of the melt convection dependence on the gravity conditions was undertaken. It was found, that the maximum convection velocity in the melt can be reduced under certain conditions. Optimal conditions to obtain a near flat solidified interface are discussed. The predicted interface shape is in agreement with one obtained experimentally by quenching. The results of 3-D calculations are compared with previous 2- D findings. A video film featuring 3-D melt convection will be presented.

Bune, Andris V.↗
NASA NTRS1999

NASA Ames Research Center R and D Services Directorate Biomedical Systems Development

The Ames Research Center R&D Services Directorate teams with NASA, other government agencies and/or industry investigators for the development, design, fabrication, manufacturing and qualification testing of space-flight and ground-based experiment hardware for biomedical and general aerospace applications. In recent years, biomedical research hardware and software has been developed to support space-flight and ground-based experiment needs including the E 132 Biotelemetry system for the Research Animal Holding Facility (RAHF), E 100 Neurolab neuro-vestibular investigation systems, the Autogenic Feedback Systems, and the Standard Interface Glove Box (SIGB) experiment workstation module. Centrifuges, motion simulators, habitat design, environmental control systems, and other unique experiment modules and fixtures have also been developed. A discussion of engineered systems and capabilities will be provided to promote understanding of possibilities for future system designs in biomedical applications. In addition, an overview of existing engineered products will be shown. Examples of hardware and literature that demonstrate the organization's capabilities will be displayed. The Ames Research Center R&D Services Directorate is available to support the development of new hardware and software systems or adaptation of existing systems to meet the needs of academic, commercial/industrial, and government research requirements. The Ames R&D Services Directorate can provide specialized support for: System concept definition and feasibility Mathematical modeling and simulation of system performance Prototype hardware development Hardware and software design Data acquisition systems Graphical user interface development Motion control design Hardware fabrication and high-fidelity machining Composite materials development and application design Electronic/electrical system design and fabrication System performance verification testing and qualification.

Pollitt, J.↗
NASA NTRS2000

Acoustic Receptivity of a Blasius Boundary Layer with 2-D and Oblique Surface Waviness

An experimental investigation was conducted to examine acoustic receptivity and subsequent boundary-layer instability evolution for a Blasius boundary layer formed on a flat plate in the presence of two-dimensional (2-D) and oblique (3-D) surface waviness. The effect of the non-localized surface roughness geometry and acoustic wave amplitude on the receptivity process was explored. The surface roughness had a well defined wavenumber spectrum with fundamental wavenumber k (sub w). A planar downstream traveling acoustic wave was created to temporally excite the flow near the resonance frequency of an unstable eigenmode corresponding to k (sub ts) = k (sub w). The range of acoustic forcing levels, epsilon, and roughness heights, DELTA h, examined resulted in a linear dependence of receptivity coefficients; however, the larger values of the forcing combination epsilon dot DELTA h resulted in subsequent nonlinear development of the Tollmien-Schlichting (T-S) wave. This study provided the first experimental evidence of a marked increase in the receptivity coefficient with increasing obliqueness of the surface waviness in excellent agreement with theory. Detuning of the 2-D and oblique disturbances was investigated by varying the streamwise wall-roughness wavenumber a,, and measuring the T-S response. For the configuration where laminar-to-turbulent breakdown occurred, the breakdown process was found to be dominated by energy at the fundamental and harmonic frequencies, indicative of K-type breakdown.

King, Rudolph A.↗
NASA NTRS1999

Integrated Avionics System (IAS), Integrating 3-D Technology On A Spacecraft Panel

As spacecraft designs converge toward miniaturization, and with the volumetric and mass challenges placed on avionics, programs will continue to advance the "state of the art" in spacecraft system development with new challenges to reduce power, mass and volume. Traditionally, the trend is to focus on high-density 3-D packaging technologies. Industry has made significant progress in 3-D technologies, and other related internal and external interconnection schemes. Although new technologies have improved packaging densities, a system packaging architecture is required that not only reduces spacecraft volume and mass budgets, but increase integration efficiencies, provide modularity and flexibility to accommodate multiple missions while maintaining a low recurring cost. With these challenges in mind, a novel system packaging approach incorporates solutions that provide broader environmental applications, more flexible system interconnectivity, scalability, and simplified assembly test and integration schemes. The Integrated Avionics System (IAS) provides for a low-mass, modular distributed or centralized packaging architecture which combines ridged-flex technologies, high-density COTS hardware and a new 3-D mechanical packaging approach, Horizontal Mounted Cube (HMC). This paper will describe the fundamental elements of the IAS, HMC hardware design, system integration and environmental test results.

Hunter, Don J.↗