SEARCH · Search NASA

Results for “DEFLECTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

NASA NTRS1982

A study of model deflection measurement techniques applicable within the national transonic facility

Moire contouring, scanning interferometry, and holographic contouring were examined to determine their practicality and potential to meet performance requirements for a model deflection sensor. The system envisioned is to be nonintrusive, and is to be capable of mapping or contouring the surface of a 1-meter by 1-meter model with a resolution of 50 to 100 points. The available literature was surveyed, and computations and analyses were performed to establish specific performance requirements, as well as the capabilities and limitations of such a sensor within the geometry of the NTF section test section. Of the three systems examined, holographic contouring offers the most promise. Unlike Moire, it is not hampered by limited contour spacing and extraneous fringes. Its transverse resolution can far exceed the limited point sampling resolution of scanning heterodyne interferometry. The availability of the ruby laser as a high power, pulsed, multiple wavelength source makes such a system feasible within the NTF.

Hildebrand, B. P.↗

NASA NTRS1982

Studies with sample conductivity, insertion rates, and particle deflection in a continuous flow electrophoresis system

The continuous flow electrophoresis system makes electrophoresis possible in a free-flowing film of aqueous electrolyte medium. The sample continuously enters the electrolyte at the top of the chamber and is subjected to the action of a lateral dc field. This divides the sample into fractions since each component has a distinctive electrophoretic mobility. Tests were made using monodisperse polystyrene latex microspheres to determine optimum sample conductivity, insertion rates and optimum electric field applications as baseline data for future STS flight experiments. Optimum sample flow rates for the selected samples were determined to be approximately 26 micro-liters/min. Experiments with samples in deionized water yielded best results and voltages in the 20 V/cm to 30 V/cm range were optimum. Deflections of formaldehyde fixed turkey and bovine erythrocytes were determined using the continuous flow electrophoresis system. The effects of particle interactions on sample resolution and migration in the chamber was also evaluated.

Williams, G., Jr.↗

NASA NTRS1983

Experimental results of a deflected thrust V/STOL nozzle research program

Four deflected thrust nozzle concepts, designed to operate at the low pressure ratio typical of high bypass-ratio turbofan engines for medium speed (subsonic) V/STOL aircraft, were studied. Maps of overall performance characteristics and exit velocity distributions are used to highlight similarities and differences between the four concepts. Analytically determined secondary flows at the exit of a 90 deg circular pipe bend are compared with the experimental results from the more complex three dimensional geometries. The relative impact of total-pressure losses and secondary flows on nozzle thrust coefficient is addressed by numerical integration of exit velocity measurements.

Burstadt, P. L.↗

NASA NTRS1983

Experimental results of a deflected thrust V/STOL nozzle research program

Burstadt, P. L.↗

NASA NTRS1984

Flow visualization and interpretation of visualization data for deflected thrust V/STOL nozzles

Flow visualization studies were made for four deflected thrust nozzle models at subsonic speeds. Based on topological rules and the assumption that observed streaks constitute continuous vector fields, available visualization pictures are interpreted and flow patterns on interior surfaces of the nozzles are synthesized. In particular, three dimensional flow structure and separations are discussed. From the synthesized patterns, the overall features of the flow field in a given nozzle can be approximately perceived.

Kao, H. C.↗

NASA NTRS1984

Rotary balance data for a typical single-engine general aviation design for an angle-of-attack range of 20 to 90 deg. 3: Influence of control deflection on predicted model D spin modes

The influence of control deflections on the rotational flow aerodynamics and on predicted spin modes is discussed for a 1/6-scale general aviation airplane model. The model was tested for various control settings at both zero and ten degree sideslip angles. Data were measured, using a rotary balance, over an angle-of-attack range of 30 deg to 90 deg, and for clockwise and counter-clockwise rotations covering an omegab/2V range of 0 to 0.5.

Ralston, J. N.↗

NASA NTRS1982

KC-135 wing and winglet flight pressure distributions, loads, and wing deflection results with some wind tunnel comparisons

A full-scale winglet flight test on a KC-135 airplane with an upper winglet was conducted. Data were taken at Mach numbers from 0.70 to 0.82 at altitudes from 34,000 feet to 39,000 feet at stabilized flight conditions for wing/winglet configurations of basic wing tip, 15/-4 deg, 15/-2 deg, and 0/-4 deg winglet cant/incidence. An analysis of selected pressure distribution and data showed that with the basic wing tip, the flight and wind tunnel wing pressure distribution data showed good agreement. With winglets installed, the effects on the wing pressure distribution were mainly near the tip. Also, the flight and wind tunnel winglet pressure distributions had some significant differences primarily due to the oilcanning in flight. However, in general, the agreement was good. For the winglet cant and incidence configuration presented, the incidence had the largest effect on the winglet pressure distributions. The incremental flight wing deflection data showed that the semispan wind tunnel model did a reasonable job of simulating the aeroelastic effects at the wing tip. The flight loads data showed good agreement with predictions at the design point and also substantiated the predicted structural penalty (load increase) of the 15 deg cant/-2 deg incidence winglet configuration.

Montoya, L. C.↗

NASA NTRS1984

Flow visualization and interpretation of visualization data for deflected thrust V/STOL nozzles

Kao, H. C.↗

NASA NTRS1985

Large deflections of a cantilever beam under arbitrarily directed tip load

The nonlinear beam equation was integrated numerically in a direct fashion to obtain results for large deflections of cantilevers under tip loads of arbitrary direction. A short BASIC computer program for performing this integration is presented. Results for selected load cases are presented. The numerical process is performed rapidly on a modern microcomputer, and comparisons with results from closed form solutions show that the process is accurate.

Mccomb, H. E., Jr.↗

NASA NTRS1985

Large deflection behavior of quasi-isotropic laminates under low-velocity impact type point loading

Eight-ply quasi-isotropic circular composite plates of Thornel 300 graphite in Narmco 5208 epoxy resin (T300/5208) were analyzed to obtain the large deformation behavior under low-velocity impact type point loads. A simple plate-membrane coupling model was developed. The impact type point loads were replaced by equivalent quasi-static point loads. The plate-membrane coupling model was used to obtain the large deformation shapes for the thin circular composite laminates. The analyses indicated that the large deformation shapes of the composite plates under point loads vary with the center point displacements, and hence are different for different load levels. Quasi-isotropic plates were analyzed by replacing anisotropic bending stiffness components with the equivalent flexural stiffness for the isotropic plates. The plate-membrane coupling model was verified by conducting a series of tests on clamped circular quasi-isotropic laminates. Deflected shapes for the thin composite plates were experimentally obtained. These shapes agreed well with the analytically predicted shapes.

Kelkar, A.↗

NASA NTRS1985

Effect of aileron deflections on the aerodynamic characteristics of a semispan model of a subsonic energy-efficient transport

An investigation was conducted in the Langley 8 Foot Transonic Pressure Tunnel to determine the effect of aileron deflections on the aerodynamic characteristics of a subsonic energy efficient transport (EET) model. The semispan model had an aspect ratio 10 supercritical wing and was configured with a conventionally located set of ailerons (i.e., a high speed aileron located inboard and a low speed aileron located outboard). Data for the model were taken over a Mach number range from 0.30 to 0.90 and an angle of attack range from approximately -2 deg to 10 deg. The Reynolds number was 2.5 million per foot for Mach number = 0.30 and 4 million per foot for the other Mach numbers. Model force and moment data, aileron effectiveness parameters, aileron hinge moment data, otherwise pressure distributions, and spanwise load data are presented.

Jacobs, P. F.↗

NASA NTRS1985

Development of optical diaphragm deflection sensors

The objective of this project was to develop high-temperature pressure sensors using non-metallic components and optical sensing methods. The sensors are to operate over a temperature range from room temperature approx. 20C to 540C, to respond to internal pressure up to 690 kPa, to respond to external pressure up to 690 kPa, and to withstand external overpressure of 2070 kPa. Project tasks include evaluating sensing techniques and sensor systems. These efforts include materials and sensing method selection, sensor design, sensor fabrication, and sensor testing. Sensors are tested as a function of temperature, pressure, overpressure, and vibration. The project results show that high-temperature pressure sensors based on glass components and optical sensing methods are feasible. The microbend optical diaphragm deflection sensor exhibits the required sensitivity and stability for use as a pressure sensor with temperature compensation. for the microbend sensor, the 95% confidence level deviation of input pressure from the pressure calculated from the overall temperature-compensated calibration equation is 3.7% of full scale. The limitations of the sensors evaluated are primarily due to the restricted temperature range of suitable commercially available optical fibers and the problems associated with glass-to-metal pressure sealing over the entire testing temperature range.

Ghering, W. L.↗

NASA NTRS1987

Protecting a Ball-Bearing-Deflection Monitor

Deflectometer probe monitors deflection of ball-bearing race in liquid oxygen with aid of small window or diaphragm. Diaphragm or window isolates optical deflectometer from liquid oxygen or other fluid in ball bearing. At high pressures, diaphragm integral part of housing preferable to window, since there would be no leakage.

Kuhr, George A.↗

NASA NTRS1986

Static deflection control of flexible beams by piezo-electric actuators

This study deals with the utilization of piezo-electric actuators in controlling the static deformation of flexible beams. An optimum design procedure is presented to enable the selection of the optimal location, thickness and excitation voltage of the piezo-electric actuators in a way that would minimize the deflection of the beam to which these actuators are bonded. Numerical examples are presented to illustrate the application of the developed optimization procedure in minimizing the structural deformation of beams of different materials when subjected to different loading and end conditions using ceramic or polymeric piezo-electric actuators. The results obtained emphasize the importance of the devised rational procedure in designing beam-actuator systems with minimal elastic distortions.

Baz, A. M.↗

NASA NTRS1987

Temperature and deflection data from the asymmetric heating of cross-ply composite tubes

Data generated while heating several cross-ply graphite-epoxy tubes on one side, along their lengths, and cooling them on the other side are presented. This heating arrangement produces a circumferential temperature gradient, and the data show that the gradient can be represented by a cosinusoidal temperature distribution. The thermally induced bending deflections caused by the temperature gradient are also presented.

Hyer, Michael W.↗

NASA NTRS1988

Flexural behavior of the continental lithosphere in Italy - Constraints imposed by gravity and deflection data

This paper presents a simple model that describes the geometry of subducted continental lithosphere as the result of flexural loading of a thin elastic sheet. The method involves a procedure for systematically matching the plate flexure and gravity data to the best-fitting two-dimensional flexural geometry obtained by a thin elastic sheet of specified elastic strength. It is shown that the model can explain both the deflection of the lithosphere and the gravity anomalies observed along four profiles across the Apennine convergent system in Italy. The results of calculations suggest that in subduction systems, like the Apennines, that are characterized by backarc extension, forces acting on subducted lithosphere at depth can be expressed at the surface in the geometry of the foredeep basin that forms adjacent to the subduction zone.

Royden, Leigh↗

NASA NTRS1988

Effect of finite width on deflection and energy release rate of an orthotropic double cantilever specimen

The problem of an orthotropic cantilevered plate subjected to a uniformly distributed end load is solved by the Rayleigh-Ritz energy method. The result is applied to laminated composite, double cantilevered specimens to estimate the effect of crack tip constraint on the transverse curvature, deflection and energy release rate. The solution is also utilized to determined finite width correction factors for fracture energy characterization tests in which neither plane stress nor plane strain conditions apply.

Schapery, R. A.↗

NASA NTRS1989

Scaling effects in the static large deflection response of graphite-epoxy composite beams

Scaling effects in the large deflection response of graphite-epoxy composite beams was investigated. Eight different scale model beams ranging from 1/6 to full-scale were subjected to an eccentric axial compressive load to promote large bending deformations and failures. Beams having laminate stacking sequences including unidirectional, angle ply, cross ply, and quasi-isotropic were tested to examine a wide variety of composite response and failure modes. The model beams were loaded under scaled test conditions until catastrophic failure. Data acquired included load, end displacement, and strain measurements, and qualitative failure measurements. The experimental data is compared to a large rotation beam analysis and a finite element model analysis. Results from the tests indicate that the beam response becomes nonlinear. Failure modes are consistent between scale models within a laminate family, however, a significant scale effect is observed in strength of the scaled beams.

Jackson, Karen E.↗