Search NASA⌕ Search

SEARCH · Search NASA

Results for “Deposition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Impact of Changes to the Atmospheric Soluble Iron Deposition Flux on Ocean Biogeochemical Cycles in the Anthropocene

Abstract Iron can be a growth‐limiting nutrient for phytoplankton, modifying rates of net primary production, nitrogen fixation, and carbon export ‐ highlighting the importance of new iron inputs from the atmosphere. The bioavailable iron fraction depends on the emission source and the dissolution during transport. The impacts of anthropogenic combustion and land use change on emissions from industrial, domestic, shipping, desert, and wildfire sources suggest that Northern Hemisphere soluble iron deposition has likely been enhanced between 2% and 68% over the Industrial Era. If policy and climate follow the intermediate Representative Concentration Pathway 4.5 trajectory, then results suggest that Southern Ocean (>30°S) soluble iron deposition would be enhanced between 63% and 95% by 2100. Marine net primary productivity and carbon export within the open ocean are most sensitive to changes in soluble iron deposition in the Southern Hemisphere; this is predominantly driven by fire rather than dust iron sources. Changes in iron deposition cause large perturbations to the marine nitrogen cycle, up to 70% increase in denitrification and 15% increase in nitrogen fixation, but only modestly impacts the carbon cycle and atmospheric CO 2 concentrations (1–3 ppm). Regionally, primary productivity increases due to increased iron deposition are often compensated by offsetting decreases downstream corresponding to equivalent changes in the rate of phytoplankton macronutrient uptake, particularly in the equatorial Pacific. These effects are weaker in the Southern Ocean, suggesting that changes in iron deposition in this region dominates the global carbon cycle and climate response.

Hamilton, Douglas S.↗

A Vertically Resolved Canopy Improves Chemical Transport Model Predictions of Ozone Deposition to North Temperate Forests

Abstract Dry deposition is the second largest tropospheric ozone (O 3 ) sink and occurs through stomatal and nonstomatal pathways. Current O 3 uptake predictions are limited by the simplistic big‐leaf schemes commonly used in chemical transport models (CTMs) to parameterize deposition. Such schemes fail to reproduce observed O 3 fluxes over terrestrial ecosystems, highlighting the need for more realistic treatment of surface‐atmosphere exchange in CTMs. We address this need by linking a resolved canopy model (1D Multi‐Layer Canopy CHemistry and Exchange Model, MLC‐CHEM) to the GEOS‐Chem CTM and use this new framework to simulate O 3 fluxes over three north temperate forests. We compare results with in situ measurements from four field studies and with standalone, observationally constrained MLC‐CHEM runs to test current knowledge of O 3 deposition and its drivers. We show that GEOS‐Chem overpredicts observed O 3 fluxes across all four studies by up to 2×, whereas the resolved‐canopy models capture observed diel profiles of O 3 deposition and in‐canopy concentrations to within 10%. Relative humidity and solar irradiance are strong O 3 flux drivers over these forests, and uncertainties in those fields provide the largest remaining source of model deposition biases. Flux partitioning analysis shows that: (a) nonstomatal loss accounts for 60% of O 3 deposition on average; (b) in‐canopy chemistry makes only a small contribution to total O 3 fluxes; and (c) the CTM big‐leaf treatment overestimates O 3 ‐driven stomatal loss and plant phytotoxicity in these temperate forests by up to 7×. Results motivate the application of fully online vertically explicit canopy schemes in CTMs for improved O 3 predictions.

Vermeuel, Michael P. [Department of Soil, Water, a↗

Formation of late-generation atmospheric compounds inhibited by rapid deposition

Reactive organic carbon species are important fuel for atmospheric chemical reactions, including the formation of secondary organic aerosol. However, in parallel to atmospheric oxidation processes, deposition can remove compounds from the atmosphere and impact downstream environments. To understand the impact of deposition on atmospheric oxidation, we present a framework for predicting and visualizing the fate of a molecule on the basis of the physicochemical properties of compounds (Henry’s law constant, vapour pressure and reaction rate constants), which are used to estimate timescales for oxidation and deposition. Further, by implementing our deposition rates in chemical models, we show that deposition substantially suppresses atmospheric reactivity and aerosol formation by removing early-generation products and preventing the formation of large fractions (up to 90%) of downstream, late-generation compounds. Deposition is frequently missing in the laboratory experiments and detailed chemical modelling, which probably biases our understanding of atmospheric composition.

54 ENVIRONMENTAL SCIENCES↗

An Improved Energy Deposition Model in MPACT and Explicit Heat Generation Coupling with CTF

The default energy deposition model in the CASL neutronics code MPACT assumes all fission energy is deposited locally in fuel rods. Furthermore, equilibrium delayed energy release is assumed for both steady-state and transient calculations. These approximations limit the accurate representation of the heat generation distribution in space and its variations over time, which are essential for power distribution and thermal-hydraulic coupling calculations. In this paper, an improved energy deposition model is presented in both the spatial and time domains. Spatially, the energy deposition through fission, neutron capture, and slowing-down reactions are explicitly modeled to account for the heat generation from all regions of a reactor core, and a gamma smearing scheme is developed that utilizes the gamma sources from neutron fission and capture. In the time domain, the delayed energy release is modeled by solving an additional equation of delayed heat emitters, similar to the equation of delayed neutron precursors.To allow the explicit heat generation coupling, the interfaces between MPACT and CTF were updated to transfer separate heat sources for different material regions (fuel, clad, moderator and guide tube). The results show that the distributions of the energy deposition between MPACT and MCNP agree very well for various 2-D assembly and quarter-core problems without TH feedback. The MPACT/CTF coupled calculation for the hot full power quarter-core case exhibited a reduced peak pin power by 2.3% and a reduced peak fuel centerline temperature by 17 K when using the explicit energy deposition and heat transfer. The new model also shows a maximum 100 pcm keff effect on assembly depletion problems and an increased overall energy release by 7% in a PWR reactivity-initiated accident (RIA) problem.

Liu, Yuxuan↗

Statistical Uncertainty of Inhalation Dose Coefficients: Impact of Particle Deposition in ICRP 66 Human Respiratory Tract Model

Inhaled radioactive materials can pose a long-term health concern, as the material can be incorporated into the body’s metabolic pathways and remain in organs and tissues for extended durations. During the retention period, the radioactive material may localize in a source organ and irradiate adjacent target organs and tissues. Distribution of these materials changes over time, requiring biokinetic modeling to evaluate their movement through various tissues and organs. The evolving distribution depends on multiple inputs characterizing the inhaled material, such as particle size and size distribution, particle density, aspect ratio, specific radionuclide, the chemical form, and solubility. In addition, biological parameters such as breathing rate, breathing type (nasal or nasal/oral), respiratory system morphometry, tidal volume, functional residual capacity, and anatomical dead space all influence material transport. These aerosol properties and physiological characteristics of the respiratory tract jointly define a range of initial conditions that influence the time-dependent distribution of radioactive material. To evaluate both uncertainty in the initial conditions of inhalation exposure and the final output (committed effective dose) from biokinetic models, a Python-based software tool, Radiological Exposure Dose Calculator (REDCAL), was developed to propagate uncertainty within the human respiratory tract model. Focusing on deposition fraction uncertainty, the primary objective was to characterize the initial activity distribution across respiratory regions as a function of anticipated particle sizes and distributions. The impact of the deposition fraction uncertainty was propagated to committed effective dose coefficients for selected radionuclides in a companion publication. For each particle size, a lognormal distribution, characterized by its geometric mean as defined within ICRP Publication 66, serves as the basis for introducing uncertainty into the physical processes governing deposition in various lung regions. Finally, this study addresses the deposition process and examines how uncertainty in deposition mechanisms affects activity distribution in the airways, ultimately presenting the expected range and standard deviation of deposited activity as a function of particle size.

International Commission on Radiological Protectio↗

Radio-frequency magnetron sputter deposition of ultrathick boron carbide films

The deposition of thick B 4 C films with low residual stress by conventional direct-current magnetron sputtering is accompanied by the formation of dust particulates contaminating the target, chamber, and substrates and leading to the formation of nodular defects in films. Here, we demonstrate that the formation of particulates is greatly reduced during radio-frequency magnetron sputtering (RFMS). We systematically study properties of B 4 C films deposited by RFMS with a substrate temperature of 330 °C, a target-to-substrate distance of 10 cm, Ar working gas pressure in the range of 4.5–12.0 mTorr (0.6–1.6 Pa), and substrate tilt angles of 0°–80°. All films are x-ray amorphous. A columnar structure develops with increasing either Ar pressure or substrate tilt. For columnar films, the column tilt angle decreases with increasing Ar pressure, which we attribute to a corresponding increase in the width of the distribution of impact angles of deposition flux. In contrast to the Keller–Simmons rule, the deposition rate increases with increasing Ar pressure, which suggests a better coupling of the RF energy to the plasma processes that lead to target sputtering at higher pressures. There is a critical substrate tilt angle above which the total residual stress is close to zero. This critical substrate tilt angle is ~0° for an Ar pressure of 12 mTorr (1.6 Pa). The lower residual stress state, necessary for depositing ultrathick films, is characterized by a larger concentration of nanoscale inhomogeneities and decreased mechanical properties. Based on these results, RFMS deposition of 60-μm-thick B 4 C films is demonstrated.

36 MATERIALS SCIENCE↗

Microbial ecology of acidic, biogenic gypsum: community structure and distribution of extremophiles on freshly formed and relict sulfate deposits in a hydrogen sulfide-rich cave

Sulfate minerals are abundant on the Martian surface, and many of these evaporite deposits are thought to have precipitated from acidic fluids. On Earth, gypsum (CaSO 4 •2H 2 O) and other sulfates sometimes form under acidic conditions, so exploring the extremophilic life that occurs in these mineral environments can help evaluate the astrobiological potential of acid sulfate depositional settings. Here, we characterized the microbial communities associated with acidic gypsum deposits in a sulfuric acid cave, where sulfate precipitation is driven by sulfide-oxidizing bacteria and archaea. We used 16S rRNA gene sequencing and cell counts to characterize gypsum-associated microorganisms in freshly formed and relict deposits throughout the cave, to test how microbial community composition and abundance would vary with distance from the sulfidic water table and with the concentration of H 2 S(g) and other gases in the cave atmosphere. We found that actively forming gypsum in the lower cave levels was colonized by low-diversity communities that have few cells compared to other environments in the cave. The most abundant taxa were Acidithiobacillus, Metallibacterium, Mycobacteria, and three different Thermoplasmatales-group archaea, which occupied distinct niches based on proximity to sulfidic streams and the concentration of gases in the cave air. By contrast, deposits in older cave levels had more diverse communities that were distinct from those associated with freshly formed gypsum and likely represent a community reliant on different energy resources. These findings show that acidic sulfate deposits serve as habitats for extremophilic microorganisms and broaden our knowledge of the life associated with terrestrial sulfates.

58 GEOSCIENCES↗

Adsorption Processes during Electrochemical Atomic Layer Deposition of Gold

Electrochemical atomic layer deposition (e-ALD) technique offers a simple and effective "wet chemistry" approach enabling high-precision monolayer-by-monolayer deposition of metal films. The process of e-ALD of Au involves lead underpotential deposition (PbUPD) followed by its redox replacement by a Au monolayer. The time evolution of the deposit mass during "one-pot" Au e-ALD is known to exhibit a unique three-stage response that is presently not well understood. In this work, we probe this response using voltammetry, electrochemical quartz crystal microgravimetry (e-QCM), and chronoamperometry to unravel the underlying mechanistic events during Au e-ALD. Furthermore, the presence of adsorbed Au +3 -ligand complex(es) (Au-L) on the Au surface is established. In stage I of e-ALD, this Au-L adsorbed layer is reduced to Au while a Pb UPD adlayer is formed. In stage II, the Pb UPD adlayer undergoes spontaneous surface-limited redox replacement by nobler Au under open-circuit conditions. Finally, in stage III, re-adsorption of the Au-L occurs on the newly deposited Au. Quantitative analysis of the deposit mass transients obtained under a variety of conditions provides an estimate of the Au-L mass and its molecular weight.

36 MATERIALS SCIENCE↗

Comparative analysis of energy deposition modes available in Serpent 2 within the framework of the supercritical water reactor - Fuel qualification test reactor physics benchmark

A joint European Canadian Chinese development of a supercritical water-cooled small modular reactor (SCW-SMR) technology is in progress since September 2020 in the framework of a Horizon 2020 project called ECC-SMART. As a main purpose of the project, proper estimates of energy deposition and its spatial distribution are prerequisites for the accurate analysis of safety related parameters of the SCW-SMR concept under development. A supercritical water reactor fuel computational benchmark model, provided by Canadian Nuclear Laboratories, was applied for detailed comparison of different energy deposition calculation options available in the Serpent 2 Monte Carlo code. The effect of energy deposition options on the normalization of the results as well as on the spatial distribution of the energy deposition are discussed. Consistent energy deposition calculation methods are presented between three Monte Carlo codes, viz., Serpent 2, MCNP6 and OpenMC. Although resource-intensive, the use of the coupled neutron-photon transport mode of Serpent 2 is recommended for accurate spatial and quantitative characterization of energy deposition in the SCW-SMR fuel assemblies, accounting for both neutron and photon heating of all the materials. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

From Deposition to Encapsulation: Roll-to-roll manufacturing of organic light emitting devices for lighting (Final Report)

Organic light emitting devices (OLEDs) are promising solid state light sources due to their high efficiency, high color quality and flexible form factors. The key to enable low cost OLED lighting, is to rapidly fabricate thin film organic layers on a continuous flexible roll, called R2R processing. This project aims to investigate the feasibility of mass production of OLED lighting using the R2R process, from deposition to encapsulation. A high efficiency white OLED is fabricated on 10 cm-wide substrate rolls in a pilot R2R tool comprising of two different organic deposition: vacuum thermal evaporation (VTE) and organic vapor phase deposition (OVPD). A high quality encapsulation process to package OLEDs is demonstrated using an atomic layer deposition tool integrated to the R2R system without air exposure. The method to achieve ultrahigh deposition rates required by R2R processing is demonstrated by OVPD. Uniform organic semiconductor thin films grown by OVPD at rates as high as 50 Å/s are achieved. A comprehensive numerical model that is capable of simulating complex, multilayer WOLED structures is developed to provide an alternative to experimental iterations of OLED design and tests. A cost estimate on the R2R production of WOLEDs for lighting is developed. Assuming a WOLED luminance of 10 klm/m 2 , the cost of a WOLED light engine is anticipated to be $\$ 12.5$ /klm. With incremental reduction in material and driver costs and improved luminance, the cost of WOLED lighting can be reduced to $\$ 6.3$ /klm in the near term. These findings suggest OLED lighting can be volume manufactured by R2R vapor deposition methods with much reduced costs compared to current batch processing methods, potentially positioning WOLEDs for use in numerous premium lighting applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Facies Analysis and Depositional Environments of the Upper Cambrian Eau Claire Formation in Central and Northern Illinois

The Cambrian Eau Claire Formation is a confining unit for geologic carbon dioxide (CO2) storage, and potentially a confining unit for hydrogen storage, within the underlying Mount Simon Sandstone in the Central and Northern Illinois Basin. However, extensive regional studies on lateral continuity, environment of deposition, and depositional fabric of the Eau Claire Formation in the Illinois Basin are minimal compared to studies of the underlying Mount Simon Sandstone. This study presents an integrated facies analysis using sedimentological, stratigraphic, ichnological, and mineralogical data to interpret the depositional environments of the Eau Claire Formation, emphasizing the dynamic nature of sedimentary systems. By combining core analyses, thin-section analysis, facies interpretation from geophysical logs, and regional stratigraphic framework interpretation, this work provides insights into the integrated depositional framework across diverse depositional environments. These findings suggest that the Eau Claire Formation in the Central and Northern Illinois Basin was deposited in a shallow marine environment, ranging from tidal flats to offshore settings. Its mixed siliciclastic-carbonate succession was primarily controlled by relative sea-level change.

58 GEOSCIENCES↗

Additive Friction Stir Deposition of a Tantalum–Tungsten Refractory Alloy

Additive friction stir deposition (AFSD) is a solid-state metal additive manufacturing technique, which utilizes frictional heating and plastic deformation to create large deposits and parts. Much like its cousin processes, friction stir welding and friction stir processing, AFSD has seen the most compatibility and use with lower-temperature metals, such as aluminum; however, there is growing interest in higher-temperature materials, such as titanium and steel alloys. In this work, we explore the deposition of an ultrahigh-temperature refractory material, specifically, a tantalum–tungsten (TaW) alloy. The solid-state nature of AFSD means refractory process temperatures are significantly lower than those for melt-based additive manufacturing techniques; however, they still pose difficult challenges, especially in regards to AFSD tooling. In this study, we perform initial deposition trials of TaW using twin-rod-style AFSD with a high-temperature tungsten–rhenium-based tool. Many challenges arise because of the high temperatures of the process and high mechanical demand on AFSD machine hardware to process the strong refractory alloy. Despite these challenges, successful deposits of the material were produced and characterized. Mechanical testing of the deposited material shows improved yield strength over that of the annealed reference material, and this strengthening is mostly attributed to the refined recrystallized microstructure typical of AFSD. These findings highlight the opportunities and challenges associated with ultrahigh-temperature AFSD, as well as provide some of the first published insights into twin-rod-style AFSD process behaviors.

36 MATERIALS SCIENCE↗

Surface Treatment Strategies for Mitigating Gas Hydrate & Asphaltene Formation, Growth, and Deposition in Flowloops

Abstract Numerous solids including gas hydrates, waxes, and asphaltenes have the potential to form in the production lines of gas and oil fields. This creates a highly non-ideal scenario as the accumulation of said species leads to flow assurance issues, especially with long-term processes like deposition. Since an ever-increasing amount of material is deposited in place at the pipe surface, production stoppage or active mitigation efforts become inevitable. The latter production issues result in increased safety risks and operational expenditures. Therefore, a cost-effective, passive deposition mitigation technology, such as a pipeline coating or surface treatment is especially appealing. The ability to address multiple pipeline flow assurance issues simultaneously without actively disrupting production would represent a dramatic step forward in this area. This study is part of a long-term ongoing effort that evaluates the performance and application of an omniphobic surface treatment for solids deposition prevention in industrially relevant systems. In particular, this specific work concentrates on the efficacy and robustness of the treatment under fully flowing conditions. The apparatuses utilized for this include two flowloops: a lab-scale, high-pressure flowloop for gas hydrate and surface treatment durability studies, and a bench-scale, atmospheric pressure loop for crude oil and asphaltene experiments. Film growth in high-pressure flowloop tests corroborated previous reports of delayed gas hydrate nucleation observed in rocking cells. Without the aid of the memory effect, treated oil-dominated experiments never experienced hydrate formation, spending upwards of a week in the hydrate stability zone (at the subcooled/fluid test conditions). Subsequent tests which utilized the memory effect then revealed that the hydrate formation rate reduced in the presence of the surface treatment compared to a bare stainless-steel surface. This testing was part of a larger set of trials conducted in the flowloop, which lasted about one year. The surface treatment durability under flowing conditions was evaluated during this time. Even after experiencing ∼4000 operating hours and 2 full pressure cycles, no evidence of delamination or damage was detected. Finally, as part of an extension to previous work, corroded surface asphaltene deposition experiments were performed in a bench-top flowloop. Treated experiments displayed an order of magnitude reduction in both total oil (all fractions of crude oil) and asphaltene fraction deposited.

03 NATURAL GAS↗

Measurement of Piston Deposit Thickness Using Laser Profilometer

In this work, a novel method of measuring the thickness of deposits on engine pistons, including within ring grooves, is described. A laser profilometer is used in conjunction with a rotary stage to measure a continuous profile of the piston with deposits, and the measurement is repeated after cleaning the deposits from the piston. Algorithms for aligning the scans and determining the differential thickness are described, and results are compared to deposit thickness measurements using a contact-type magnetic induction coating thickness gauge. This method allows continuous measurement of deposit thickness across the entire surface including lands and ring grooves as well as quantification of the volume of the deposits.

42 ENGINEERING↗

The use of ERTS-1 images in the search for large sulfide deposits in the Chagai District, Pakistan

The author has identified the following significant results. Visual examination of color composites was tested under relatively ideal conditions for direct detection of large hydrothermal sulfide deposits at the low-grade porphyry copper deposit at Saindak, western Chagai District, Pakistan. The Saindak deposit is characterized by an elongate zone of easily eroded sulfide-rich rock surrounded by a resistant rim of hornfels and propylitically altered rock. The geomorphic features related to the Saindak deposit are easily distinguished on ERTS-1 images. Attempts to detect a color anomaly using false-color composites were not successful. About 36,000 square km of the western Chagai District were examined on false-color composites for direct evidence of large sulfide deposits. New geologic information acquired from the images was used in conjunction with the known geology to evaluate two previously known proposed areas and to suggest seven additional targets for field checking, one of which is proposed on the basis of tonal anomaly alone. The study also showed that Saindak-type deposits are not likely to be present in some extensive areas of the Chagai District; and also that a rim like that at Saindak does not form if regional metamorphism has increased the resistance of the country rock to erosion.

Schmidt, R. G.↗

Theoretical and experimental studies of the deposition of Na2So4 from seeded combustion gases

Flames in a Mach 0.3 atmospheric pressure laboratory burner rig were doped with sea salt, NaS04, and NaCl, respectively, in an effort to validate theoretical dew point predictions made by a local thermochemical equilibrium (LTCE) method of predicting condensation temperatures of sodium sulfate in flame environments. Deposits were collected on cylindrical platinum targets placed in the combustion products, and the deposition was studied as a function of collector temperature. Experimental deposition onset temperatures checked within experimental error with LTCE-predicted temperatures. A multicomponent mass transfer equation was developed to predict the rate of deposition of Na2SO4(c) via vapor transport at temperatures below the deposition onset temperature. Agreement between maximum deposition rates predicted by this chemically frozen boundary layer (CFBL) theory and those obtained in the seeded laboratory burner experiments is good.

Kohl, F. J.↗

Development of sputtering process to deposit stoichiometric zirconia coatings for the inside wall of regeneratively cooled rocket thrust chambers

Thermal barrier coatings of yttria stabilized zirconia and zirconia-ceria mixtures were deposited by RF reactive sputtering. Coatings were 1-2 mils thick, and were deposited on copper cylinders intended to simulate the inner wall of a regeneratively cooled thrust chamber. Coating stoichiometry and adherence were investigated as functions of deposition parameters. Modest deposition rates (approximately 0.15 mil/hr) and subambient sustrate temperatures (-80 C) resulted in nearly stoichiometric coatings which remained adherent through thermal cycles between -196 and 400 C. Coatings deposited at higher rates or substrates temperatures exhibited greater oxygen deficiences, while coatings deposited at lower temperatures were not adherent. Substrate bias resulted in structural changes in the coating and high krypton contents; no clear effect on stoichiometry was observed.

Busch, R.↗

The Response of a Quartz Crystal Microbalance to a Liquid Deposit

A theory was developed for predicting the loss of response of a QCM (Quartz Crystal Microbalance) to a liquid deposit due to viscous effects in the deposit. The loss of response is expressed by a response factor, equal to the response of the QCM to a liquid film divided by its response to a solid film of the same mass per unit area. The theory assumes a droplet-type deposit morphology, and considers the influence of droplet distribution parameters. Experiments were conducted to examine the validity of the theory, using DC 704 silicone oil as the subject deposit material. Experiments were made in two series: one with constant deposit mass and variable temperature, the other with variable deposit mass and constant temperature. Interpretation of the data using the theory has enabled information on droplet area coverage and number density to be deduced.

Glassford, A. P. M.↗