Search NASA⌕ Search

SEARCH · Search NASA

Results for “Energy Intake”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Measuring OutdoorAir Intake Rates Using Electronic Velocity Sensors at Louvers and Downstream of Airflow Straighteners

Practical and accurate technologies are needed for continuously measuring and controlling outdoor air (OA) intake rates in commercial building heating, ventilating, and air conditioning (HVAC) systems. This project evaluated two new measurement approaches. Laboratory experiments determined that OA flow rates were measurable with errors generally less than 10percent using electronic air velocity probes installed between OA intake louver blades or at the outlet face of louvers. High accuracy was maintained with OA flow rates as low as 15percent of the maximum for the louvers. Thus, with this measurement approach HVAC systems do not need separate OA intakes for minimum OA supply. System calibration parameters are required for each unique combination of louver type and velocity sensor location but calibrations are not necessary for each system installation. The research also determined that the accuracy of measuring OA flow rates with velocity probes located in the duct downstream of the intake louver was not improved by installing honeycomb airflow straighteners upstream of the probes. Errors varied with type of upstream louver, were as high as 100percent, and were often greater than 25percent. In conclusion, use of electronic air velocity probes between the blades of OA intake louvers or at the outlet face of louvers is a highly promising means of accurately measuring rates of OA flow into HVAC systems. The use of electronic velocity probes downstream of airflow straighteners is less promising, at least with the relatively small OA HVAC inlet systems employed in this research.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Measuring Outdoor Air Intake Rates into Existing Building

Practical and accurate technologies are needed for continuously measuring and controlling outdoor air (OA) intake rates in commercial building heating, ventilating, and air conditioning (HVAC) systems. This project evaluated two new measurement approaches. Laboratory experiments determined that OA flow rates were measurable with errors generally less than 10 percent using electronic air velocity probes installed between OA intake louver blades or at the outlet face of louvers. High accuracy was maintained with OA flow rates as low as 15 percent of the maximum for the louvers. Thus, with this measurement approach HVAC systems do not need separate OA intakes for minimum OA supply. System calibration parameters are required for each unique combination of louver type and velocity sensor location but calibrations are not necessary for each system installation. The research also determined that the accuracy of measuring OA flow rates with velocity probes located in the duct downstream of the intake louver was not improved by installing honeycomb airflow straighteners upstream of the probes. Errors varied with type of upstream louver, were as high as 100 percent, and were often greater than 25 percent. In conclusion, use of electronic air velocity probes between the blades of OA intake louvers or at the outlet face of louvers is a highly promising means of accurately measuring rates of OA flow into HVAC systems. The use of electronic velocity probes downstream of airflow straighteners is less promising, at least with the relatively small OA HVAC inlet systems employed in this research.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Low emission turbo compound engine system

A diesel or HHCI engine has an air intake and an exhaust for products of combustion. A pair of turbochargers receive the products of combustion in a series relationship and an exhaust aftertreatment device receive the products of combustion from the downstream turbine. A power turbine receives the output from the exhaust aftertreatment device and an EGR system of the power turbine passes a selected portion of the output to a point upstream of the upstream turbocharger compressor. A device adds fuel to the aftertreatment device to regenerate the particulate filter and the power turbine recoups the additional energy. The power turbine may be used to drive accessories or the prime output of the engine.

33 ADVANCED PROPULSION SYSTEMS↗

Evaluation of digestively resistant or soluble fibers, short- and medium-chain fatty acids, trace minerals, and antibiotics in nonchallenged nursery pigs on performance, digestibility, and intestinal integrity

Abstract Three experiments (EXP) were conducted to determine the effect of feed additives on performance, intestinal integrity, gastrointestinal volatile fatty acids (VFA), and energy and nutrient digestion in nonchallenged nursery pigs. In EXP 1, 480 pigs (6.36-kg body weight, BW) were placed into 96 pens with 5 pigs/pen, and allotted to 1 of 10 dietary treatments: 1) negative control containing no feed additive (NC), 2) NC + 44 mg chlortetracycline and 38.5 mg tiamulin/kg diet (CTsb), 3) NC + 5% resistant potato starch (RSpo), 4) NC + 5% soluble corn fiber (SCF), 5) NC + 5% sugar beet pulp (SBP), 6) NC + 0.30% fatty acid mix (FAM), 7) NC + 0.10% phytogenic blend of essential oils and flavoring compounds (PHY), 8) NC + 50 mg Cu and 1,600 mg zinc oxide/kg diet (CuZn), 9) NC + 5% resistant corn starch (RScn), and 10) NC + 0.05% β-glucan (BG) for 28 d. There was no impact of dietary treatment on BW gain or feed intake (P ≥ 0.22). Pigs fed diets containing SCF, CTsb, and RSpo resulted in microbial community differences compared to pigs fed the NC (P < 0.05). In EXP 2, 48 barrows (12.8 kg BW) were selected at the end of EXP 1 and fed the same dietary treatments they had previously received: 1) NC, 2) NC + 5% RScn, 3) NC + 5% SCF, and 4) NC + FAM for 8 d. There was no effect of feeding diets containing RScn, SCF, or FAM on in vivo intestinal permeability (P ≤ 0.21). Ileal or colon pH, concentrations of VFA did not differ due to dietary treatment (P ≥ 0.36), but pigs fed diets containing FAM resulted in a greater butyric acid concentration in the cecum compared to pigs fed the NC (P ≤ 0.05). In EXP 3, 156 pigs (6.11 kg BW) were placed into 52 pens with 3 pigs/pen and allotted to 1 of 4 dietary treatments arranged in a factorial manner: 1) NC, 2) NC + 5% RSpo, 3) NC + 0.30% FAM, and 4) NC + 5% RSpo + 0.30% FAM for 24 d. Feeding pigs diets containing RSpo did not affect BW gain (P = 0.91) while pigs fed diets containing FAM grew improved BW gain (P = 0.09). Colonic butyric acid concentrations were greater in pigs fed diets containing RSpo (P = 0.03), while pigs fed diets containing FAM exhibited reduced total VFA concentrations (P = 0.11). The results indicate that supplementing diets with digestively resistant but fermentable fibers, short- and medium-chain fatty acids, or antibiotics do not have a consistent effect, positive or negative, on markers of intestinal integrity or barrier function, intestinal VFA patterns, ATTD of energy and nutrients, or on pig performance.

Agriculture↗

Simulated weightlessness - Effects on bioenergetic balance

As a prelude to a flight experiment, an attempt was made to separate energy requirements associated with gravity from all other metabolic needs. The biological effects of weightlessness were simulated by suspending animals in a harness so that antigravity muscles were not supporting the body. Twelve pairs of rats were allowed to adapt to wearing a harness for 5 d. Experimental animals were then suspended in harness for 7 d followed by recovery for 7 d. Control animals were harnessed but never suspended. Oxygen consumption, carbon dioxide production and rate of (C-14)O2 expiration from radio-labeled glucose were monitored on selected days. Food intake and body mass were recorded daily. Metabolic rate decreased in experimental animals during 7 d of suspension and returned to normal during recovery. Although some of the metabolic changes may have related to variation in food intake, simulated weightlessness appears to directly affect bioenergetic balance.

Jordan, J. P.↗

System and method for cooling a combustion gas charge

The present invention relates to a system and method for cooling a combustion gas charge prior. The combustion gas charge may include compressed intake air, exhaust gas, or a mixture thereof. An evaporator is provided that may then receive a relatively high temperature combustion gas charge and discharge at a relatively lower temperature. The evaporator may be configured to operate with refrigeration cycle components and/or to receive a fluid below atmospheric pressure as the phase-change cooling medium.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

The PROPEL Hydro System (Final Report)

This paper summarizes research, development and outcome of a modular system for powering non-powered dams. There are approximately 77,000 non-powered dams in the US, a non-trivial fraction of which could be used to generate power. Development in this area has been slow because building projects costs too much and takes too long. The PROPEL-Hydro system combines modular components for the intake and foundation, an ai driven project design and evaluation tool, and a turbine optimized for performance on small and low head sites. Work included a combination of site evaluation, refinement of power electronics, value analysis supported by computational fluid mechanics and software development to support a project evaluation tool. The result is a reduction in installed cost/kW and resulting LCOE.

13 HYDRO ENERGY↗

Analysis of Interstitial Elements in Niobium with Secondary Ion Mass Spectrometry (SIMS)

Superconducting Radio Frequency (SRF) cavities provide enhanced efficiency and reduced energy utilization in present day particle accelerators. Niobium (Nb) is the material of choice for these cavities due to its high critical temperature and critical magnetic field. In order to understand why certain treatments, especially a low temperature bake, improve performance, it is important to study Nb surface characteristics and identify elemental contamination that can affect the performance of the cavity. H, C, O, and N are of interest because they are interstitial impurities in Nb. In earlier work, SIMS analysis using a CAMECA IMS-6F with Cs{sup +} primary beam showed that C and N were probably not significant factors impacting performance but there was a very high level of H in the Nb. Ion implants of C, N, O, and D into Nb provided quantification of C, N, O and indicated that D is very mobile in the Nb. Further analyses showed that heat treated Nb has lower levels of surface H than non heat treated Nb and subsequent removal of surface oxide by etching causes intake of H in a heat treated Nb sample. This result helps confirm the role of surface oxide as a hydrogen barrier. To further understand the oxide, Nb samples were anodized to obtain a thicker surface oxide and H and D were implanted into this oxide to check for the appearance of implant peaks. SIMS depth profile analyses were carried out and confirmed the presence of the implant shape for these elements in the oxide. Relative Sensitivity Factor (RSFs) could then be calculated for quantification of H in the oxide. Since the Nb matrix signal showed little change from the oxide to the substrate, the same RSF was used to estimate the H concentration in the Nb at 2x10{sup 22} atoms/cm{sup 3}(approximately 40% mole fraction H).

36 MATERIALS SCIENCE↗

Multi-level computational exploration of advanced combustion engine operating strategies

Advanced combustion engine (ACE) research is typically carried out on single-cylinder research engines. These engines are designed to tightly control fueling and conditions at intake valve closure (IVC) and to precisely measure in-cylinder conditions and emissions. However, to be able to measure and control engine operation so precisely, these research engines typically do not feature intake and exhaust tracts that resemble those in production engines, specifically in regards to turbomachinery, heat exchangers, and exhaust gas recirculation (EGR) systems. For this reason, these research engines are effective for understanding in-cylinder combustion parameters such as heat release rate, burn duration, combustion efficiency, pollutant formation, and exhaust valve opening (EVO) conditions. Here, this paper applies high fidelity simulations to determine the feasibility of achieving a chosen single cylinder engine operating point on a production type homogeneous charge compression ignition (HCCI) engine, using a partial fuel stratification (PFS) strategy. To accomplish this, a Converge 3 dimensional (3D) – computational fluid dynamics (CFD) model of the experimental combustion chamber and intake and exhaust runners was created to simulate the experimental engine. This model was used to simulate an operating point achieved experimentally, as well as to determine the sensitivity of the operating point to variations in intake pressure, intake temperature, injection timing, injected mass, and EGR fraction. The results from these simulations were fed into a 1-dimensional engine simulation created in AVL Boost, featuring production-type intake and exhaust systems, including turbomachinery and heat exchangers necessary to create the required IVC conditions. This full engine simulation was used to assess the cycle efficiency of the engine at the experimental operating condition, and to assess whether changes to this operating point in intake temperature, intake pressure, direct injection timing, or fueling are beneficial to the cycle efficiency and engine-out emissions. In addition, the sensitivity of promising engine operating points to injection timing and injection mass are determined to evaluate the potential stability of these operating points.

33 ADVANCED PROPULSION SYSTEMS↗

THE LATE PEAKING AFTERGLOW OF GRB 100418A

GRB 100418A is a long gamma-ray burst (GRB) at redshift z = 0.6235 discovered with the Swift Gamma-ray Burst Explorer with unusual optical and X-ray light curves. After an initial short-lived, rapid decline in X-rays, the optical and X-ray light curves observed with Swift are approximately flat or rising slightly out to at least {approx}7 x 10{sup 3} s after the trigger, peak at {approx}5 x 10{sup 4} s, and then follow an approximately power-law decay. Such a long optical plateau and late peaking is rarely seen in GRB afterglows. Observations with Rapid Eye Mount during a gap in the Swift coverage indicate a bright optical flare at {approx}2.5 x 10{sup 4} s. The long plateau phase of the afterglow is interpreted using either a model with continuous injection of energy into the forward shock of the burst or a model in which the jet of the burst is viewed off-axis. In both models the isotropic kinetic energy in the late afterglow after the plateau phase is {>=}10{sup 2} times the 10{sup 51} erg of the prompt isotropic gamma-ray energy release. The energy injection model is favored because the off-axis jet model would require the intrinsic T{sub 90} for the GRB jet viewed on-axis to be very short, {approx}10 ms, and the intrinsic isotropic gamma-ray energy release and the true jet energy to be much higher than the typical values of known short GRBs. The non-detection of a jet break up to t {approx} 2 x 10{sup 6} s indicates a jet half-opening angle of at least {approx}14{sup 0}, and a relatively high-collimation-corrected jet energy of E{sub jet} {>=} 10{sup 52} erg.

79 ASTRONOMY AND ASTROPHYSICS↗

Reducing the Impacts of Hydroelectric Dams on Juvenile Anadromous Fishes: Bioengineering Evaluations Using Acoustic Imaging in the Columbia River, USA

Dams impact the survival of juvenile anadromous fishes by obstructing migration corridors, lowering water quality, delaying migrations, and entraining fish in turbine discharge. To reduce these impacts, structural and operational modifications to dams— such as voluntary spill discharge, turbine intake guidance screens, and surface flow outlets—are instituted. Over the last six years, we have used acoustic imaging technology to evaluate the effects of these modifications on fish behavior, passage rates, entrainment zones, and fish/flow relationships at hydroelectric projects on the Columbia River. The imaging technique has evolved from studies documenting simple movement patterns to automated tracking of images to merging and analysis with concurrent hydraulic data. This chapter chronicles this evolution and shows how the information gleaned from the scientific evaluations has been applied to improve passage conditions for juvenile salmonids. We present data from Bonneville and The Dalles dams that document fish behavior and entrainment zones at sluiceway outlets (14 to 142 m3/s), fish passage rates through a gap at a turbine intake screen, and the relationship between fish swimming effort and hydraulic conditions. Dam operators and fisheries managers have applied these data to support decisions on operational and structural changes to the dams for the benefit of anadromous fish populations in the Columbia River basin.

13 HYDRO ENERGY↗

Low Cost, High Efficiency, Ultra-Low NOx ARICE Solution Using HCCI Combustion

This report documents the development of a Homogeneous Charge Compression Ignition engine for the Advanced Reciprocating Internal Combustion Engine Program of the California Energy Commission. The goal of this research project was to develop and demonstrate a homogeneous charge compression ignition internal combustion engine for stationary power generation applications meeting the advanced reciprocating internal combustion engine program efficiency and emissions goals, primarily the development of a 200 kilowatt engine operating at 45 percent efficiency with 0.015 grams/brake horse power hour nitrogen oxide emissions. While this project did not attain this goal, innovative solutions were developed to many of the technical barriers that prevent homogeneous charge compression ignition from being a practical combustion system for the stationary power generation marketplace. The project focused on converting a Caterpillar 6-cylinder engine model 3406 natural gas generator set to operate in natural gas homogeneous charge compression ignition mode. A key challenge of homogeneous charge compression ignition is control of combustion. A novel system for control of the engine was developed based on thermal management, where recovered heat from the engine exhaust was used to control intake air temperature. Controlling intake air temperature allows control of the timing of the homogeneous charge compression ignition combustion process, and a specially designed dual intake manifold system allowed for control of the engine on a cylinder-by-cylinder basis. Control of fuel-air ratio is another significant technical issue in homogeneous charge compression ignition combustion, and is especially difficult with natural gas fuelled engines. A novel approach to fuel-air ratio control was developed by modifying a conventional natural gas carburetor and coupling it with an electronic pressure regulator, allowing for precise control of fuel-air ratio. Startup is challenging for homogeneous charge compression ignition engines, most strategies proposed involve starting the engine in conventional operation (i.e., spark-ignition), then transition to homogeneous charge compression ignition once the engine is started. The transition approach invites hazards, because the spark-ignition operating regime (fuel- air ratio) is not compatible with homogeneous charge compression ignition operating regime. An approach has been developed to start the engine directly in homogeneous charge compression ignition mode, avoiding operation in regimes that could be potentially hazardous. The technical accomplishments of this project lay the groundwork for future development of practical homogeneous charge compression ignition engines.

03 NATURAL GAS↗

Generation Forecasting for Small Run-of-the-River Hydroelectric Systems Using Statistical Learning Models

With an increasing interest in constructing new run-of-the-river (ROR) hydroelectric generation over the more traditional reservoir-based hydroelectric systems, there is an increasing operational challenge due to the volatility of stream flow. The Snohomish County Public Utilities District (SnoPUD) has recently invested in the construction and operation of 3 new run-of-the-river projects in Northwestern Washington along Calligan Creek, Hancock Creek, and Youngs Creek. In order to effectively plan generation dispatch, SnoPUD has expressed interest in the development of an accurate forecasting tool to predict the generation capacity for these ROR systems. The following research project aims to use statistical learning models, namely Hidden Markov Models (HMMs), to predict day-ahead generation capacities for the aforementioned ROR systems. These models are constructed using 12 years of historical stream flow data collected at the intake sites and precipitation data recorded at the National Oceanic and Atmospheric Administration (NOAA) Alpine Meadows station. Four methods of constructing the models are studied for their forecast accuracies, and are compared with the persistence model. Despite using only one set of observable variables, the HMMs are shown to have slight improvements in accuracy over the persistence model approach, which shows great optimism for future work.

13 HYDRO ENERGY↗

A two-dimensional numerical study of the flow inside the combustion chambers of a motored rotary engine

A numerical study was performed to investigate the unsteady, multidimensional flow inside the combustion chambers of an idealized, two-dimensional, rotary engine under motored conditions. The numerical study was based on the time-dependent, two-dimensional, density-weighted, ensemble-averaged conservation equations of mass, species, momentum, and total energy valid for two-component ideal gas mixtures. The ensemble-averaged conservation equations were closed by a K-epsilon model of turbulence. This K-epsilon model of turbulence was modified to account for some of the effects of compressibility, streamline curvature, low-Reynolds number, and preferential stress dissipation. Numerical solutions to the conservation equations were obtained by the highly efficient implicit-factored method of Beam and Warming. The grid system needed to obtain solutions were generated by an algebraic grid generation technique based on transfinite interpolation. Results of the numerical study are presented in graphical form illustrating the flow patterns during intake, compression, gaseous fuel injection, expansion, and exhaust.

Shih, T. I. P.↗

A two-dimensional numerical study of the flow inside the combustion chamber of a motored rotary engine

A numerical study was performed to investigate the unsteady, multidimensional flow inside the combustion chambers of an idealized, two-dimensional, rotary engine under motored conditions. The numerical study was based on the time-dependent, two-dimensional, density-weighted, ensemble-averaged conservation equations of mass, species, momentum, and total energy valid for two-component ideal gas mixtures. The ensemble-averaged conservation equations were closed by a K-epsilon model of turbulence. This K-epsilon model of turbulence was modified to account for some of the effects of compressibility, streamline curvature, low-Reynolds number, and preferential stress dissipation. Numerical solutions to the conservation equations were obtained by the highly efficient implicit-factored method of Beam and Warming. The grid system needed to obtain solutions were generated by an algebraic grid generation technique based on transfinite interpolation. Results of the numerical study are presented in graphical form illustrating the flow patterns during intake, compression, gaseous fuel injection, expansion, and exhaust.

Shih, T. I-P.↗

Annual Report FY2014 Alternative Fuels DISI Engine Research

Due to concerns about future petroleum supply and accelerating climate change, increased engine efficiency and alternative fuels are of interest. This project contributes to the science-base needed by industry to develop highly efficient DISI engines that also beneficially exploit the different properties of alternative fuels. Lean operation is studied since it can provide higher efficiencies than traditional non-dilute stoichiometric operation. Since lean operation can lead to issues with ignition stability, slow flame propagation and low combustion efficiency, focus is on techniques that can overcome these challenges. Specifically, fuel stratification can be used to ensure ignition and completeness of combustion, but may lead to soot and NO x emissions challenges. Advanced ignition system and intake air preheating both promote ignition stability. Controlled end-gas autoignition can be used maintain high combustion efficiency for ultra-lean well-mixed conditions. However, the response of both combustion and exhaust emission to these techniques depends on the fuel properties. Therefore, to achieve optimal fuel-economy gains, the combustion-control strategies of the engine must adopt to the fuel being utilized.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Investigation of Knock limited Compression Ratio of Ethanol Gasoline Blends

Ethanol offers significant potential for increasing the compression ratio of SI engines resulting from its high octane number and high latent heat of vaporization. A study was conducted to determine the knock limited compression ratio of ethanol gasoline blends to identify the potential for improved operating efficiency. To operate an SI engine in a flex fuel vehicle requires operating strategies that allow operation on a broad range of fuels from gasoline to E85. Since gasoline or low ethanol blend operation is inherently limited by knock at high loads, strategies must be identified which allow operation on these fuels with minimal fuel economy or power density tradeoffs. A single cylinder direct injection spark ignited engine with fully variable hydraulic valve actuation (HVA) is operated at WOT conditions to determine the knock limited compression ratio (CR) of ethanol fuel blends. The geometric compression ratio is varied by changing pistons, producing CR from 9.2 to 13.66. The effective CR is varied using an electro-hydraulic valvetrain that changed the effective trapped displacement using both Early Intake Valve Closing (EIVC) and Late Intake Valve Closing (LIVC). The EIVC and LIVC strategies result in effective CR being reduced while maintaining the geometric expansion ratio. It was found that at substantially similar engine conditions, increasing the ethanol content of the fuel results in higher engine efficiency and higher engine power. These can be partially attributed to a charge cooling effect and a higher heating valve of a stoichiometric mixture for ethanol blends (per unit mass of air). Additional thermodynamic effects on and a mole multiplier are also explored. It was also found that high CR can increase the efficiency of ethanol fuel blends, and as a result, the fuel economy penalty associated with the lower energy content of E85 can be reduced by about a third. Such operation necessitates that the engine be operated in a de-rated manner for gasoline, which is knock-prone at these high CR, in order to maintain compatibility. By using EIVC and LIVC strategies, good efficiency is maintained with gasoline, but power is reduced by about 34%.

02 PETROLEUM↗

Impacts of an additional exhaust shaft on WIPP performance - 15170

The Waste Isolation Pilot Plant (WIPP), located in southeastern New Mexico, has been developed by the U.S. Department of Energy (DOE) for the geologic (deep underground) disposal of transuranic (TRU) waste. WIPP performance assessment (PA) demonstrates repository performance from facility closure to 10,000 years after closure. The recent radiological release event at the WIPP site has temporarily halted waste emplacement activities at the facility. A modified ventilation system is envisioned that will provide sufficient airflow necessary for the resumption of full-rate disposal operations in the future. A primary component of the modified ventilation system is an additional exhaust shaft in the north end of the repository. There are four shafts currently in the repository north end, namely a salt handling shaft, an exhaust shaft, a waste shaft, and an air intake shaft. These shafts are combined into a single composite shaft in WIPP PA that captures the combined impacts of all of them. The proposed additional exhaust shaft is combined with the four existing shafts in the repository model to determine its impacts on long-term repository performance. Moreover, mined volume in the repository north end is modified in the repository representation so as to include additional drifts created to access the new shaft. Computed gas and brine flow behaviors corresponding to the repository with the additional exhaust shaft are compared to those obtained in the PA executed for the 2014 Compliance Re-certification Application (the CRA-2014 PA). Results show that the repository with an additional exhaust shaft and drifts yields brine and gas flow behaviors similar to the current repository configuration. It is concluded that WIPP continues to satisfy regulatory compliance limits with the addition of an exhaust shaft and its access drifts, with compliance curves like those found in the CRA-2014 PA for total normalized releases. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗