SEARCH · Search NASA

Results for “Error field control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

NASA NTRS1981

An operations manual for the Spinning Mode Synthesizer in the Langley Aircraft Noise Reduction Laboratory

The need for a dependable and controllable noise source and the consequent development of the Spinning Mode Synthesizer (SMS) is discussed. Configuration of the SMS incorporated into the flow duct facility is reported. Turbofan noise is composed of a series of fundamental acoustical modes, which are produced by acoustic drivers equispaced circumferentially around the flow duct. Pressure field is compared to an ideal result in an optimization algorithm, adjusting driver settings until system error is minimized. The following items are included: operating instructions, a detailed description of the system, and a user's guide to data acquisition packages available.

Palumbo, D. L.↗

NASA NTRS1988

Source localization of Jupiter's Io dependent radio emissions

The peak frequencies of the Io-dependent part of the Jovian emissions are compared with the surface gyrofrequency determined from Jovian magnetic models in order to localize the source of Jovian radio emissions. The bulk of the Io-controlled emissions was found to be delayed by up to 70 deg of equatorial longitude from the predicted instantaneous position of the Io flux tube, with the L and S emissions both displaying this same unexpected behavior. It is suggested that the source of these emissions is delayed substantially with respect to Io either as an Alfven-wave delay or because of errors in the magnetic field models.

Aubier, Monique G.↗

NASA NTRS2000

Comprehensive Evaluation of Attitude and Orbit Estimation Using Actual Earth Magnetic Field Data

A single, augmented Extended Kalman Filter (EKF), which simultaneously and autonomously estimates spacecraft attitude and orbit has been developed and successfully tested with real magnetometer and gyro data only. Because the earth magnetic field is a function of time and position, and because time is known quite precisely, the differences between the computed and measured magnetic field components, as measured by the magnetometers throughout the entire spacecraft orbit, are a function of both orbit and attitude errors. Thus, conceivably these differences could be used to estimate both orbit and attitude; an observability study validated this assumption. The results of testing the EKF with actual magnetometer and gyro data, from four satellites supported by the NASA Goddard Space Flight Center (GSFC) Guidance, Navigation, and Control Center, are presented and evaluated. They confirm the assumption that a single EKF can estimate both attitude and orbit when using gyros and magnetometers only.

Deutschmann, Julie K.↗

NASA NTRS2000

Kepler Mission: End-to-End System Demonstration

A test facility has been constructed to demonstrate the capability of differential ensemble photometry to detect transits of Earth-size planets orbiting solar-like stars. The main objective is to determine the effects of various noise sources on the capability of a CCD photometer to maintain a system relative precision of 1 x $10^(-5)$ for mv = 12 stars in the presence of system-induced noise sources. The facility includes a simulated star field, fast optics to simulate the telescope, a thinned back-illuminated CCD similar to those to be used on the spacecraft and computers to perform the onboard control, data processing and extraction. The test structure is thermally and mechanically isolated so that each source of noise can be introduced in a controlled fashion and evaluated for its contribution to the total noise budget. The effects of pointing errors or a changing thermal environment are imposed by piezo-electric devices. Transits are injected by heating small wires crossing apertures in the star plate. Signals as small as those from terrestrial-size transits of solar-like stars are introduced to demonstrate that such planets can be detected under realistic noise conditions. Examples of imposing several noise sources and the resulting detectabilities are presented. These show that a differential ensemble photometric approach CCD photometer can readily detect signals associated with Earth-size transits.

Borucki, William↗

NASA NTRS1993

Atmospheric moisture fields derived by satellite observations over the tropical Pacific Ocean

Values of precipitable water are retrieved over the tropical and subtropical Pacific Ocean from TOVS infrared and microwave channel brightness temperature and OLR observations by means of stepwise linear regression. The most useful temperature and moisture sensing channels are pre-selected from sensitivity tests of a radiative transfer model. Numerous models are developed and tested against collocated radiosonde observations and Nimbus-7 SMMR precipitable water estimates. For RAOB comparisons, the best estimator used 15 TOVS predictors and captured 71.1 deg percent of the variance (+0.62 g/sq cm standard error) for column precipitable water; for precipitable water of 700-500 mb bulk layer, these values were 71.7 percent and +/- 0.17 g/sq cm. Little skill of estimated precipitable water was obtained for moisture above 500 mb. Regressions were less skillful against SMMR, unless collocation parameters were tightly controlled; SMMR was less acceptable than RAOB's because of observational drift and errors. Generally, the most skillful predictors were boundary layer brightness temperatures of TOVS channels and satellite estimated stability indices. 'Moisture channels' were hardly useful except for estimating middle and upper tropospheric moisture. Additional regression models were constructed testing the sensitivity to different observational and meteorological characteristics. Models which used some in situ observations surface observations or stabilities calculated from RAOB, were the most successful. The best of these explained 87.5 percent of the variance but the regression selected almost no TOVS channels, relying instead on conventional RAOB and surface observations. A set of four regression models were developed, stratifying atmospheric characteristics on the basis of collocated OLR values. These models improved the variance explained by 5.0 percent; the model associated with the highest OLR values (275 W/sq m less than or equal to OLR; that is, no cloud) showed only marginal skill. Precipitable water fields were generated from the best TOVS-only model for seven days in January 1983 and compared with SMMR-estimated fields. OLR fields and ECMWF precipitable water analysis. The TOVS regression model compared favorably to the SMMR analysis in amplitudes and features. It revealed more evolving synoptic signal than the ECMWF analysis. In synoptically active regions, it differed with respect to the OLR analysis, primarily because of actual differences in the vertical distribution of water vapor.

Chung, Hyosang↗

NASA NTRS2019

Impact of GMI All-Sky Radiance Assimilation in the NASA GEOS Forecast System

The assimilation of cloud- and precipitation-affected ("all-sky") radiances has become an important focus of development at most numerical weather prediction centers. Efforts at the Global Modeling and Assimilation Office (GMAO) have focused on all-sky assimilation of GPM Microwave Imager (GMI) radiances, which became operational in the GEOS real-time production system in July 2018. Implementation of the all-sky capability required several upgrades to the GEOS hybrid 4D-EnVar assimilation infrastructure including the addition of control variables for cloud liquid, cloud ice, rain and snow, enhancements to the radiative transfer model, new hybrid background and observational error models, and modified quality control and bias correction procedures. This talk describes the impact of GMI all-sky radiance assimilation on GEOS analyses and forecasts as determined from examination of various metrics including statistics of background departures and analysis increments, forecast skill scores, and forecast sensitivity observation impact (FSOI) calculations. It is shown that in addition to the hydrometeors themselves, the initial wind, temperature and pressure fields all undergo significant dynamic adjustment in response to the analyzed cloud and precipitation features. Assimilation of GMI radiances leads to improved forecasts of lower tropospheric wind, temperature and humidity, especially in the tropics. The largest forecast improvements occur during the first 48 hours, with diminishing impact thereafter. However, combining GMI all-sky assimilation with improvements to the GEOS model physics as in the recent implementation of the real-time production system, extends these forecast improvements well in to the medium range. FSOI results based on a 24-hr moist global energy norm show that GMI radiances provide nearly uniform beneficial impact throughout the tropics, with more mixed impacts in the subtropics. While the overall impact of GMI is smaller than that of other, much more numerous microwave and hyperspectral infrared radiance types, its impact is among the largest of all radiance types on a per-observation basis.

Gelaro, Ron↗

NASA NTRS2000

Hurricane Wind Field Measurements with Scanning Airborne Doppler Lidar During CAMEX-3

During the 1998 Convection and Moisture Experiment (CAMEX-3), the first hurricane wind field measurements with Doppler lidar were achieved. Wind fields were mapped within the eye, along the eyewall, in the central dense overcast, and in the marine boundary layer encompassing the inflow region. Spatial coverage was determined primarily by cloud distribution and opacity. Within optically-thin cirrus slant range of 20- 25 km was achieved, whereas no propagation was obtained during penetration of dense cloud. Measurements were obtained with the Multi-center Airborne Coherent Atmospheric Wind Sensor (MACAWS) on the NASA DC-8 research aircraft. MACAWS was developed and operated cooperatively by the atmospheric lidar remote sensing groups of NOAA Environmental Technology Laboratory, NASA Marshall Space Flight Center, and Jet Propulsion Laboratory. A pseudo-dual Doppler technique ("co-planar scanning") is used to map the horizontal component of the wind at several vertical levels. Pulses from the laser are directed out the left side of the aircraft in the desired directions using computer-controlled rotating prisms. Upon exiting the aircraft, the beam is completely eyesafe. Aircraft attitude and speed are taken into account during real-time signal processing, resulting in determination of the ground-relative wind to an accuracy of about 1 m/s magnitude and about 10 deg direction. Beam pointing angle errors are about 0.1 deg, equivalent to about 17 m at 10 km. Horizontal resolution is about 1 km (along-track) for typical signal processor and scanner settings; vertical resolution varies with range. Results from CAMEX-3 suggest that scanning Doppler wind lidar can complement airborne Doppler radar by providing wind field measurements in regions that are devoid of hydrometeors. At present MACAWS observations are being assimilated into experimental forecast models and satellite Doppler wind lidar simulations to evaluate the relative impact.

Rothermel, Jeffry↗

NASA NTRS1972

Space shuttle guidance, navigation and control equation document no. 4: Precision state and filter weighting matrix extrapolation

The Precision State and Filter Weighting Matrix Extrapolation Routine is described which provides the capability to extrapolate any spacecraft geocentric state vector either backwards or forwards in time through a force field consisting of the earth's primary central-force gravitational attraction and a superimposed perturbing acceleration. The routine also provides the capability of extrapolating the filter-weighting matrix along the precision trajectory. This matrix is a square root form of the error covariance matrix and contains statistical information relative to the accuracies of the state vectors and certain other optionally estimated quantities. The routine is a cooled algorithm for the numerical solution of modified forms of the basic differential equations which are satisfied by the geocentric state vector of the spacecraft's center of mass and by the filter-weighting matrix.

Robertson, W. M.↗

NASA NTRS1985

Measurement of Thematic Mapper data quality

Thematic Mapper data from Landsat-4 and Landsat-5 were examined for band-to-band registration, absolute geodetic registration, periodic noise and spatial resolution. Between focal planes, appreciable misregistrations existed in early data products but were corrected in later data products. The analysis of absolute geodetic registration used only system-corrected data because ground control point-corrected data were unavailable. Geodetic registration errors averaged only 9.7 pixels, less than expected for system-corrected data. Periodic noise at four spatial frequencies was observed in Landsat-5 Thematic Mapper data by using Fourier analysis on small areas over water. Magnitudes of periodic noise components were consistent within a scene. The modulation transfer function was determined for two Landsat-4 scenes. The effective instantaneous field of view was 40.8 meters in one case, and 48.6 meters in the other.

Wrigley, R. C.↗

NASA NTRS1987

Nonuniform sampling techniques for antenna applications

A two-dimensional sampling technique, which can employ irregularly spaced samples (amplitude and phase) in order to generate the complete far-field patterns is presented. The technique implements a matrix inversion algorithm, which depends only on the nonuniform sampled data point locations and with no dependence on the actual field values at these points. A powerful simulation algorithm is presented to allow a real-life simulation of many reflector/feed configurations and to determine the usefulness of the nonuniform sampling technique for the copolar and cross-polar patterns. Additionally, an overlapped window concept and a generalized error simulation model are discussed to identify the stability of the technique for recovering the field data among the nonuniform sampled data. Numerical results are tailored for the pattern reconstruction of a 20-m offset reflector antenna operating at L-band. This reflector is planned to be used in a proposed measurement concept of large antenna aboard the Space Shuttle, whereby it would be almost impractical to accurately control the movement of the Shuttle with respect to the RF source in prescribed directions in order to generate uniform sampled points. Also, application of the nonuniform sampling technique to patterns obtained using near-field measured data is demonstrated. Finally, results of an actual far-field measurement are presented for the construction of patterns of a reflector antenna from a set of nonuniformly distributed measured amplitude and phase data.

Rahmat-Samii, Yahya↗

NASA NTRS1984

Effect of low-frequency ambient magnetic fields on the control unit and RF head of a commercial SQUID magnetometer

The control unit and RF head of the SHE model 330XRFSQUID system are shown to be sensitive to ambient ac magnetic fields below 1 HZ, which cause the appearance of false signals corresponding to a magnetometer signal of 0.000001 phi(0) per gauss of field applied. The control unit shows a sensitivity that is linear with frequency, suggesting that the signal is generated by Faraday induction. In contrast, the RF head response is independent of frequency and shows a strong second-harmonic coversion. This response may be due to the magnetic field sensitivity of the ferrite core inductor in the tuned amplifier of the RF head. These signals induced by ambient fields are a potential source of error in Stanford's Relativity Gyroscope experiment, which uses SQUID's on board a rolling satellite as part of the gyroscope readout system. The extent of the magnetic field sensitivity in these components necessitates the use of additional magnetic shielding aboard the satellite.

Marcus, C. M.↗

NASA NTRS1953

Flight Tests of a 0.13-Scale Model of the Convair XFY-1 Vertically Rising Airplane in a Setup Simulating that Proposed for Captive-Flight Tests in a Hangar, TED No. NACA DE 368

An experimental investigation has been conducted to determine the dynamic stability and control characteristics of a 0.13-scale free-flight model of the Convair XFY-1 airplane in test setups representing the setup proposed for use in the first flight tests of the full-scale airplane in the Moffett Field airship hangar. The investigation was conducted in two parts: first, tests with the model flying freely in an enclosure simulating the hangar, and second, tests with the model partially restrained by an overhead line attached to the propeller spinner and ground lines attached to the wing and tail tips. The results of the tests indicated that the airplane can be flown without difficulty in the Moffett Field airship hangar if it does not approach too close to the hangar walls. If it does approach too close to the walls, the recirculation of the propeller slipstream might cause sudden trim changes which would make smooth flight difficult for the pilot to accomplish. It appeared that the tethering system proposed by Convair could provide generally satisfactory restraint of large-amplitude motions caused by control failure or pilot error without interfering with normal flying or causing any serious instability or violent jerking motions as the tethering lines restrained the model.

Lovell, Powell M., Jr.↗

DOE OSTI2026

Comparative Performance of Gaussian Plume and Backward Lagrangian Stochastic Models for Near-Field Methane Emission Estimation Using a Single Controlled Release Experiment

Methane (CH 4 ) is a major component of natural gas and a potent greenhouse gas. Increasing atmospheric methane concentrations are attributed to emissive anthropogenic activities by an average of 13 ppb per yr since 2020 and are linked to a changing global climate. Mitigating CH 4 emissions from oil and gas production sites has recently become a target to reduce overall greenhouse gas emissions; however, monitoring the efficacy of mitigation strategies depends on accurate quantification of CH 4 emissions at the facility-level. Near-field quantification of methane (CH 4 ) emissions from oil and gas (O&G) facilities remains challenging due to the effects of atmospheric variability and sensor configuration on atmospheric dispersion models. This study evaluates the performance of two atmospheric dispersion models, the Gaussian plume (GP) and backward Lagrangian stochastic (bLS), by comparing calculated CH 4 emissions to controlled single-point emissions between 0.4 and 5.2 kg CH 4 h −1 . Emissions were calculated by both models using 121 individual sets of measurements comprising five-minute averaged downwind methane mixing ratios and matching meteorological data. The comparison shows that the bLS approach achieved a higher proportion of emission estimates within a factor of two (FAC2) of the known emission rates compared to the GP approach. The emissions calculated by the bLS model also had a lower multiplicative error and reduced bias relative to GP. Other error-based metrics further confirmed the bLS model performed better, as it yielded lower RMSE and MAE than GP. Statistical analysis of the emission data shows that the lateral and vertical alignment of the source and the sensor plays a critical role in emission estimations, as measurements made closer to the plume centerline and at a distance between 40 and 80 m downwind yielded the best FAC2 agreement. High wind meander degraded the ability of both approaches to generate representative emissions, particularly with the GP approach, as it violates the modeling approach’s assumption of steady-state emissions. Data suggest emissions calculated by the bLS model are comprehensively in better agreement, but the computational demands of the modeling approach and integration into fenceline systems limit real-time applicability. While these results provide insight into model performance under controlled near-field conditions, their applicability to more complex or heterogeneous oil and gas production environments (e.g., the regions Marcellus or Unita Basins) remains limited and uncertain.

gaussian plume↗

NASA NTRS1999

Improving Reanalyses Using TRMM and SSM/I-Derived Precipitation and Total Precipitable Water Observations

Global reanalyses currently contain significant errors in the primary fields of the hydrological cycle such as precipitation, evaporation, moisture, and the related cloud fields, especially in the tropics. The Data Assimilation Office (DAO) at the NASA Goddard Space Flight Center has been exploring the use of rainfall and total precipitable water (TPW) observations from the Tropical Rainfall Measuring Mission (TRMM) Microwave Imager (TMI) and the Special Sensor Microwave/ Imager (SSM/I) instruments to improve these fields in reanalyses. The DAO has developed a "1+1"D procedure to assimilate 6-hr averaged rainfall and TPW into the Goddard Earth Observing System (GEOS) Data Assimilation System (DAS). The algorithm is based on a 6-hr time integration of a column version of the GEOS DAS. The "1+1" designation refers to one spatial dimension plus one temporal dimension. The scheme minimizes the least-square differences between the satellite-retrieved rain rates and those produced by the column model over the 6-hr analysis window. The control variables are analysis increments of moisture within the Incremental Analysis Update (IAU) framework of the GEOS DAS. This 1+1D scheme, in its generalization to four dimensions, is related to the standard 4D variational assimilation but differs in its choice of the control variable. Instead of estimating the initial condition at the beginning of the assimilation cycle, it estimates the constant IAU forcing applied over a 6-hr assimilation cycle. In doing so, it imposes the forecast model as a weak constraint in a manner similar to the variational continuous assimilation techniques. We present results from an experiment in which the observed rain rate and TPW are assumed to be "perfect". They show that assimilating the TMI and SSM/I-derived surface precipitation and TPW observations improves not only the precipitation and moisture fields but also key climate parameters directly linked to convective activities such as clouds, the outgoing longwave radiation, and the large-scale circulation in the tropics. In particular, assimilating these data types reduce the state-dependent systematic errors in the assimilated products. The improved analysis also leads to a better short-range forecast, but the impact is modest compared with improvements in the time-averaged fields. These results suggest that, in the presence of biases and other errors of the forecast model, it is possible to improve the time-averaged "climate content" in the assimilated data without comparable improvements in the short-range forecast skill. Results of this experiment provide a useful benchmark for evaluating error covariance models for optimal use of these data types.

Hou, Arthur Y.↗

DOE OSTI2020

A dynamic thermal algal growth model for pilot-scale open-channel raceways

Here this study describes the makeup of and results from a simulation consisting of a lumped thermal model integrated with a dynamic algae growth model to simulate the microalgae productivity of an open-channel raceway cultivation system. The thermal model considers the dynamic effects of weather, light absorption, convective heat transfer, radiation heat transfer, conductive heat transfer, thermal capacitance, and water control strategies. The dynamic algae growth model solves a set of ordinary differential equations consisting of growth functions dependent on incident radiation, temperature, nutrient availability, basal metabolism, and losses due to dark- and photo-respiration. Relative errors in the predicted ash-free dry weight of Nannochloropsis oceanica are 12.5%, -6.1%, and 4.4% for three separate replicates of cultivation cycles (~4.2 m 2 ) performed at AzCATI during the ATP 3 Unified Field Studies in Fall, Spring, and Summer. This research demonstrates that thermal modeling is an essential contributor to the validation of microalgae growth models.

09 BIOMASS FUELS↗

NASA NTRS2015

Zernike Wavefront Sensor Modeling Development for LOWFS on WFIRST-AFTA

WFIRST-AFTA design makes use of an existing 2.4m telescope for direct imaging of exoplanets. To maintain the high contrast needed for the coronagraph, wavefront error (WFE) of the optical system needs to be continuously sensed and controlled. Low Order Wavefront Sensing (LOWFS) uses the rejected starlight from an immediate focal plane to sense wavefront changes (mostly thermally induced low order WFE) by combining the LOWFS mask (a phase plate located at the small center region with reflective layer) with the starlight rejection masks, i.e. Hybrid Lyot Coronagraph (HLC)'s occulter or Shaped Pupil Coronagraph (SPC)'s field stop. Zernike wavefront sensor (ZWFS) measures phase via the phase-contrast method and is known to be photon noise optimal for measuring low order aberrations. Recently, ZWFS was selected as the baseline LOWFS technology on WFIST/AFTA for its good sensitivity, accuracy, and its easy integration with the starlight rejection mask. In this paper, we review the theory of ZWFS operation, describe the ZWFS algorithm development, and summarize various numerical sensitivity studies on the sensor performance. In the end, the predicted sensor performance on SPC and HLC configurations are presented.

Zernike phase contrast↗

DOE OSTI2026

Correlation-aware binning for small-angle neutron scattering via Gaussian-process inference

Binning in small-angle neutron scattering (SANS) is typically performed empirically, with fixed parameters chosen for convenience rather than statistical optimality. Such practices often fail to balance statistical precision and spatial resolution, leading to inconsistencies across instruments and datasets. Here we establish a correlation-aware framework that determines the optimal bin width from first principles by extending the classical Freedman–Diaconis (FD) rule to account for inter-bin correlations with a Gaussian process. In this formulation, the scattering intensity is treated as a smooth stochastic field whose statistical coherence is described by a covariance matrix. Analytical expressions of errors derived from this model yield closed-form criteria that separate the total deviation into contributions from counting noise, aliasing distortion and curvature-dependent correlation effects. Expressed in reduced variables, the resulting dimensionless error surface reveals a continuous transition from the uncorrelated FD regime to the correlation-dominated limit, providing a unified description of noise suppression and resolution control. Because the formulation depends only on the profile characteristics of scattering intensity I(Q), specifically its average intensity and first- and second-order derivatives, it applies generally to any SANS measurement regardless of sample, instrument or geometry. Experimental validation using small- and ultra-small-angle neutron scattering data confirms the predicted scaling behavior, demonstrating that correlation-aware inference systematically reduces mean-squared error and enables information-efficient reproducible data reduction across materials and instruments.

Tung, Chi-Huan [ORNL] (ORCID:0000000221972074)↗

DOE OSTI2025

Rapid SACR Observations of Convection at Bankhead National Forest (RAPID) Field Campaign Report

Improving our representation of convective cell processes requires better quantification of convective clouds throughout their entire life cycle. This includes gaining a clearer understanding of the controls on key convective cloud properties, such as updraft intensity, particle size distributions, rainfall rates, and hydrometeor species. Our inability to improve convective cloud process modeling stems, in part, from a limited understanding of convective cell properties, particularly given how rapidly these storms evolve. This lack of detailed observations in the most intense and organized convective storms is especially significant, as large errors remain in representing these clouds, which are critical for severe weather prediction and Earth system model performance. Cloud and precipitation radars are essential tools for studying cloud microphysics and dynamics, particularly in deeper convective clouds. The recent U.S. Department of Energy Atmospheric Radiation Measurement (ARM) User Facility’s third Mobile Facility (AMF3) Bankhead National Forest (BNF) deployment provides a unique opportunity to investigate important land–atmosphere interactions, as well as the environmental controls on deep convective cloud processes, in a location favorable for frequent convection. We operate the X/Ka-band Scanning ARM Cloud Radar (X/Ka SACR) using a scan strategy optimized to capture these rapidly evolving clouds and their properties, thereby improving studies of deep convective cloud processes. This effort is strengthened by a complementary and coordinated partnership with ongoing university and multi-agency radar activities collocated in north Alabama—a unique opportunity to examine clouds and precipitation from a lifetime-centric perspective.

54 ENVIRONMENTAL SCIENCES↗