Search NASA⌕ Search

SEARCH · Search NASA

Results for “Exhaust”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Flight velocity effects on exhaust noise of a wedge nozzle installed on an underwing nacelle on an F-106 airplane

It is important to know whether the relatively high takeoff speeds of supersonic transport aircraft will change the exhaust noise levels of nozzles from those measured at static conditions. To gain some insight into this question, a modified F-106B aircraft was used to conduct flyover and static tests on a wedge nozzle. Flight velocity had an adverse effect on exhaust noise when compared with static results at the same relative jet velocity but a beneficial effect when compared with static results at the same absolute jet velocity. The wedge nozzle, which has a two-dimensional wedge surface rather than an axisymmetric plug surface, had a higher peak flyover noise level than the plug nozzle.

Burley, R. R.↗
NASA NTRS1975

Payload dose rate from direct beam radiation and exhaust gas fission products

A study was made to determine the dose rate at the payload position in the NERVA System (1) due to direct beam radiation and (2) due to the possible effect of fission products contained in the exhaust gases for various amounts of hydrogen propellant in the tank. Results indicate that the gamma radiation is more significant than the neutron flux. Under different assumptions the gamma contribution from the exhaust gases was 10 to 25 percent of total gamma flux.

Capo, M. A.↗
NASA NTRS1976

Diffusion algorithms and data reduction routine for onsite real-time launch predictions for the transport of Delta-Thor exhaust effluents

The National Aeronautics and Space Administration/Marshall Space Flight Center multilayer diffusion algorithms have been specialized for the prediction of the surface impact for the dispersive transport of the exhaust effluents from the launch of a Delta-Thor vehicle. This specialization permits these transport predictions to be made at the launch range in real time so that the effluent monitoring teams can optimize their monitoring grids. Basically, the data reduction routine requires only the meteorology profiles for the thermodynamics and kinematics of the atmosphere as an input. These profiles are graphed along with the resulting exhaust cloud rise history, the centerline concentrations and dosages, and the hydrogen chloride isopleths.

Stephens, J. B.↗
NASA NTRS1976

Summary of nozzle-exhaust plume flowfield analyses performed in support of space shuttle applications

Results are summarized of various analyses of the exhaust plumes of the space shuttle. Specific topics discussed included: the development of the two-phase plume flow field model, including finite rate chemistry and free molecular effects; analyses of exhaust plume simulation studies; verification of the analytical two-phase plume flow field model; and complete documentation of the two-phase plume computer code.

Smith, S. D.↗
NASA NTRS1976

Experimental research in the use of electrets in measuring effluents from rocket exhaust and a review of standard air quality measuring devices

Seven standard types of measuring devices used to obtain the chemical composition of rocket exhaust effluents were discussed. The electrets, a new measuring device, are investigated and compared with established measuring techniques. The preliminary results obtained show that electrets have multipollutant measuring capabilities, simplicity of deployment, speed of assessment or analysis, and may be an important and valuable tool in measuring pollutants from space vehicle rocket exhaust.

Susko, M.↗
NASA NTRS1976

Jet noise characteristics of unsuppressed duct burning turbofan exhaust system

Recent aero-acoustic tests of model coannular nozzles have shown that less noise is generated if the higher-velocity jet is exhausted from the outer annular passage rather than from the primary nozzle. These findings are of particular significance to a duct-burning turbofan (DBTF) engine being studied for application to an advanced supersonic transport. Unlike conventional turbofan engines that have peak velocities from the primary nozzle, it is possible to design a DBTF engine to have a fan velocity higher than that of the primary flow. Results are presented for a NASA-sponsored model test program that covers a range of fan to primary-area ratios from 0.75 to 1.2, and a range of fan to primary-velocity ratios from 0.4 to 2.8. Correlations are given that relate radiated sound power to fan velocity, fan to primary-velocity ratio, and fan to primary-area ratio. Corresponding exhaust-plume velocity-traverse data are presented which suggest that the observed noise benefits may be due to the more rapid decay of the annular flow because of shear stresses on the inner surface that result from the lower-velocity primary flow.

Packman, A. B.↗
NASA NTRS1975

On the effects of flight on jet engine exhaust noise

Recent flight data on jet engine exhaust noise do not agree with projections based on classical jet noise theories. This paper demonstrates that these differences may be reconciled by considering the combined effects of jet mixing noise and internally-generated engine exhaust noise. The source strength of the internally-generated noise is assumed to be unaffected by flight, as has been shown in small-scale free-jet experiments. The directivity of the internally-generated noise is assumed to be the same statically as that given in the NASA interim prediction method for core engine noise. However, it is assumed that in flight the internally generated noise is subject to the convective amplification effect of a simple source. The absolute levels of the internally-generated noise are obtained from an empirical fit of some typical engine data. The static and flight jet noise are predicted using the NASA interim prediction method for jet noise. It is shown that in many cases, although jet mixing may be the dominant noise source statically, much of the flyover noise signature is dominated by internally-generated noise.

Stone, J. R.↗
NASA NTRS1976

Environmental Effects of Space Shuttle Solid Rocket Motor Exhaust Plumes

The deposition of NOx and HCl in the stratosphere from the space shuttle solid rocket motors (SRM) and exhaust plume is discussed. A detailed comparison between stratospheric deposition rates using the baseline SRM propellant and an alternate propellant, which replaces ammonium perchlorate by ammonium nitrate, shows the total NOx deposition rate to be approximately the same for each propellant. For both propellants the ratio of the deposition rates of NOx to total chlorine-containing species is negligibly small. Rocket exhaust ground cloud transport processes in the troposphere are also examined. A brief critique of the multilayer diffusion models (presently used for predicting pollutant deposition in the troposphere) is presented, and some detailed cloud rise calculations are compared with data for Titan 3C launches. The results show that, when launch time meteorological data are used as input, the model can reasonably predict measured cloud stabilization heights.

Hwang, B.↗
NASA NTRS1976

Studies of the exhaust products from solid propellant rocket motors

This study was undertaken to determine the feasibility of conducting environmental chamber tests on the physical processes which occur when a solid rocket motor exhaust mixes with the ambient atmosphere. Of particular interest was the interaction between hydrogen chloride, aluminum oxide, and water vapor. The program consisted of three phases: (1) building a small rocket motor and using it to provide the exhaust species in a controlled environment; (2) evaluating instruments used to detect and measure HCl concentrations and if possible determining whether the HCl existed in the gaseous state or as an acid aerosol; (3) monitoring a series of 6.4-percent scale space shuttle motor tests and comparing the results to the environmental chamber studies. Eighteen firings were conducted in an environmental chamber with the initial ambient relative humidity set at values from 29 to 100 percent. Two additional firings were made in a large shed, and four were made on an open concrete apron. Six test firings at MSFC were monitored, and the ground level concentrations are reported. Evidence is presented which shows that the larger Al2O3 (5 to 50 micrometers) particles from the rocket motor can act as condensation nuclei. Under appropriate ambient conditions where there is sufficient water vapor this results in the formation of an acid aerosol. Droplets of this acid were detected both in the environmental chamber and in the scaled shuttle engine tests.

Dawbarn, R.↗
NASA NTRS1977

Method for obtaining aerodynamic data on hypersonic configurations with scramjet exhaust flow simulation

A hypersonic wind tunnel test method for obtaining credible aerodynamic data on a complete hypersonic vehicle (generic X-24c) with scramjet exhaust flow simulation is described. The general problems of simulating the scramjet exhaust as well as accounting for scramjet inlet flow and vehicle forces are analyzed, and candidate test methods are described and compared. The method selected as most useful makes use of a thrust-minus-drag flow-through balance with a completely metric model. Inlet flow is diverted by a fairing. The incremental effect of the fairing is determined in the testing of two reference models. The net thrust of the scramjet module is an input to be determined in large-scale module tests with scramjet combustion. Force accounting is described, and examples of force component levels are predicted. Compatibility of the test method with candidate wind tunnel facilities is described, and a preliminary model mechanical arrangement drawing is presented. The balance design and performance requirements are described in a detailed specification. Calibration procedures, model instrumentation, and a test plan for the model are outlined.

Hartill, W. R.↗
NASA NTRS1977

Rocket exhaust effluent modeling for tropospheric air quality and environmental assessments

The various techniques for diffusion predictions to support air quality predictions and environmental assessments for aerospace applications are discussed in terms of limitations imposed by atmospheric data. This affords an introduction to the rationale behind the selection of the National Aeronautics and Space Administration (NASA)/Marshall Space Flight Center (MSFC) Rocket Exhaust Effluent Diffusion (REED) program. The models utilized in the NASA/MSFC REED program are explained. This program is then evaluated in terms of some results from a joint MSFC/Langley Research Center/Kennedy Space Center Titan Exhaust Effluent Prediction and Monitoring Program.

Stephens, J. B.↗
NASA NTRS1977

Scramjet exhaust simulation technique for hypersonic aircraft nozzle design and aerodynamic tests

Current design philosophy for scramjet-powered hypersonic aircraft results in configurations with the entire lower fuselage surface utilized as part of the propulsion system. The lower aft-end of the vehicle acts as a high expansion ratio nozzle. Not only must the external nozzle be designed to extract the maximum possible thrust force from the high energy flow at the combustor exit, but the forces produced by the nozzle must be aligned such that they do not unduly affect aerodynamic balance. The strong coupling between the propulsion system and aerodynamics of the aircraft makes imperative at least a partial simulation of the inlet, exhaust, and external flows of the hydrogen-burning scramjet in conventional facilities for both nozzle formulation and aerodynamic-force data acquisition. Aerodynamic testing methods offer no contemporary approach for such vehicle design requirements. NASA-Langley has pursued an extensive scramjet/airframe integration R&D program for several years and has recently developed a promising technique for simulation of the scramjet exhaust flow for hypersonic aircraft. Current results of the research program to develop a scramjet flow simulation technique through the use of substitute gas blends are described in this paper.

Hunt, J. L.↗
NASA NTRS1976

Exhaust gas emissions of a vortex breakdown stabilized combustor

Exhaust gas emission data are described for a swirl stabilized continuous combustor. The combustor consists of confined concentric jets with premixed fuel and air in the inner jet and air in the outer jet. Swirl may be induced in both inner and outer jets with the sense of rotation in the same or opposite directions (co-swirl and counter-swirl). The combustor limits NO emissions by lean operation without sacrificing CO and unburned hydrocarbon emission performance, when commercial-grade methane and air fired at one atmosphere without preheat are used. Relative swirl direction and magnitude are found to have significant effects on exhaust gas concentrations, exit temperatures, and combustor efficiencies. Counter-swirl gives a large recirculation zone, a short luminous combustion zone, and large slip velocities in the interjet shear layer. For maximum counter-swirl conditions, the efficiency is low.

Yetter, R. A.↗
NASA NTRS1978

Electrets used to measure exhaust cloud effluents from Solid Rocket Motor (SRM) during demonstration model (DM-2) static test firing

Electrets were compared with fixed flow samplers during static test firing. The measurement of the rocket exhaust effluents by samplers and electrets indicated that the Solid Rocket Motor had no significant effect on the air quality in the area sampled. The results show that the electrets (a passive device which needs no power) can be used effectively alongside existing measuring devices (which need power). By placing electrets in areas where no power is available, measurements may be obtained. Consequently, it is a valuable complementary instrument in measuring rocket exhaust effluents in areas where other measuring devices may not be able to assess the contaminants.

Susko, M.↗
NASA NTRS1978

Shock capturing finite-difference and characteristic reference plane techniques for the prediction of three-dimensional nozzle-exhaust flowfields

This report summarizes work accomplished under Contract No. NAS1-12726 towards the development of computational procedures and associated numerical. The flow fields considered were those associated with airbreathing hypersonic aircraft which require a high degree of engine/airframe integration in order to achieve optimized performance. The exhaust flow, due to physical area limitations, was generally underexpanded at the nozzle exit; the vehicle afterbody undersurface was used to provide additional expansion to obtain maximum propulsive efficiency. This resulted in a three dimensional nozzle flow, initialized at the combustor exit, whose boundaries are internally defined by the undersurface, cowling and walls separating individual modules, and externally, by the undersurface and slipstream separating the exhaust flow and external stream.

Dash, S.↗
NASA NTRS1978

Analysis of three-dimensional ducted and exhaust plume flowfields

Computational procedures are described for analyzing three-dimensional supersonic internal flows and multinozzle exhaust plume flowfields. The computer codes (BIGMAC and CHAR3D) embodying these procedures cater to a broad spectrum of geometric situations via the use of multiple reference plane grid networks in several coordinate systems. Shock capturing techniques are employed to trace the propagation and interaction of multiple shock surfaces. Gas properties consist of combustion products in chemical equilibrium. The computational accuracy of the codes is assessed via comparisons with the results of other codes and experimental data. Results are presented for the flows in two-dimensional ducts, corner flows, flow in a rectangular nozzle, and the plume flowfields for exhausts issuing out of single and multiple rectangular nozzles.

Dash, S. M.↗
NASA NTRS1978

Rocket exhaust plume impingement on the Voyager spacecraft

In connection with the conduction of the long-duration Voyager missions to the outer planets and the sophisticated propulsion systems required, it was necessary to carry out an investigation to avoid exhaust plume impingement problems. The rarefied gas dynamics literature indicates that, for most engineering surfaces, the assumption of diffuse reemission and complete thermal accommodation is warranted in the free molecular flow regime. This assumption was applied to an analysis of a spacecraft plume impingement problem in the near-free molecular flow regime and yielded results to within a few percent of flight data. The importance of a correct treatment of the surface temperature was also demonstrated. Specular reflection, on the other hand, was shown to yield results which may be unconservative by a factor of 2 or 3. It is pointed out that one of the most difficult portions of an exhaust plume impingement analysis is the simulation of the impinged hardware. The geometry involved must be described as accurately and completely as possible.

Baerwald, R. K.↗
NASA NTRS1979

Electrets used in measuring rocket exhaust effluents from the space shuttle's solid rocket booster during static test firing, DM-3

The purpose of this experimental research was to compare Marshall Space Flight Center's electrets with Thiokol's fixed flow air samplers during the Space Shuttle Solid Rocket Booster Demonstration Model-3 static test firing on October 19, 1978. The measurement of rocket exhaust effluents by Thiokol's samplers and MSFC's electrets indicated that the firing of the Solid Rocket Booster had no significant effect on the quality of the air sampled. The highest measurement by Thiokol's samplers was obtained at Plant 3 (site 11) approximately 8 km at a 113 degree heading from the static test stand. At sites 11, 12, and 5, Thiokol's fixed flow air samplers measured 0.0048, 0.00016, and 0.00012 mg/m3 of CI. Alongside the fixed flow measurements, the electret counts from X-ray spectroscopy were 685, 894, and 719 counts. After background corrections, the counts were 334, 543, and 368, or an average of 415 counts. An additional electred, E20, which was the only measurement device at a site approximately 20 km northeast from the test site where no power was available, obtained 901 counts. After background correction, the count was 550. Again this data indicate there was no measurement of significant rocket exhaust effluents at the test site.

Susko, M.↗