SEARCH · Search NASA

Results for “Experimental Test Range”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

NASA NTRS1987

Stresses and deformations in angle-ply composite tubes

The stress and deformations in angle-ply composite tubes subjected to axisymmetric thermal loading were investigated both experimentally and analytically. For the theoretical portion a generalized plane strain elasticity analysis was developed. The analysis included mechanical and thermal loading, and temperature-dependent material properties. The elasticity analysis was also used to study the effect of including a thin metallic coating on a graphite-epoxy tube. The stresses in the coatings were found to be quite high, exceeding the yield stress of aluminum. An important finding in the analytical studies was the fact that even tubes with a balanced-symmetric lamination sequence exhibit shear deformation, or twist. For the experimental portion an apparatus was developed to measure torsional and axial response in the temperature range of 140 to 360 K. Eighteen specimens were tested, combining three material systems, eight lamination sequences, and three off-axis ply orientation angles. For the twist response, agreement between analysis and experiment was found to be good. The axial response of the tubes tested was found to be greater than predicted by a factor of three. As a result, it is recommended that the thermally induced axial deformations be investigated, both experimentally and analytically.

Rousseau, Carl Q.↗

NASA NTRS1986

Experimental evaluation of wall Mach number distributions of the octagonal test section proposed for NASA Lewis Research Center's altitude wind tunnel

Wall Mach number distributions were determined over a range of test-section free-stream Mach numbers from 0.2 to 0.92. The test section was slotted and had a nominal porosity of 11 percent. Reentry flaps located at the test-section exit were varied from 0 (fully closed) to 9 (fully open) degrees. Flow was bled through the test-section slots by means of a plenum evacuation system (PES) and varied from 0 to 3 percent of tunnel flow. Variations in reentry flap angle or PES flow rate had little or no effect on the Mach number distributions in the first 70 percent of the test section. However, in the aft region of the test section, flap angle and PES flow rate had a major impact on the Mach number distributions. Optimum PES flow rates were nominally 2 to 2.5 percent wtih the flaps fully closed and less than 1 percent when the flaps were fully open. The standard deviation of the test-section wall Mach numbers at the optimum PES flow rates was 0.003 or less.

Harrington, Douglas E.↗

NASA NTRS1976

Some anomalies observed in wind-tunnel tests of a blunt body at transonic and supersonic speeds

An investigation of anomalies observed in wind tunnel force tests of a blunt body configuration was conducted at Mach numbers from 0.20 to 1.35 in the Langley 8-foot transonic pressure tunnel and at Mach numbers of 1.50, 1,80, and 2.16 in the Langley Unitary Plan wind tunnel. At a Mach number of 1.35, large variations occurred in axial force coefficient at a given angle of attack. At transonic and low supersonic speeds, the total drag measured in the wind tunnel was much lower than that measured during earlier ballistic range tests. Accurate measurements of total drag for blunt bodies will require the use of models smaller than those tested thus far; however, it appears that accurate forebody drag results can be obtained by using relatively large models. Shock standoff distance is presented from experimental data over the Mach number range from 1.05 to 4.34. Theory accurately predicts the shock standoff distance at Mach numbers up to 1.75.

Brooks, J. D.↗

NASA NTRS1973

Geometric factors affecting noise suppresion and thrust loss of divergent-lobe supersonic jet noise suppressor

The thrust loss and noise suppression of a divergent-lobe supersonic jet noise suppressor were experimentally determined over a range of nozzle pressure ratios of 1.5 to 4.0. These small-scale cold flow tests were made to determine the effect on thrust and noise of: suppressor length, rearward facing step height, suppressor divergence angle, and ejector shroud length and location. Noise suppression was achieved at nozzle pressure ratios of 2.5 and greater. Maximum lobe jet noise attenuation of 15 db with thrust loss differences of 1.5 percent compared to the convergent nozzle were obtained at a nozzle pressure ratio of 3.5 with an ejector shroud two nozzle diameters long. Without the ejector the attenuation was 13 db with thrust loss differences of 11 percent. Short suppressors approximately one primary nozzle throat diameter long performed as well as longer suppressors. Rearward facing step height had a significant effect on noise suppression. Ejector shrouds two nozzle diameters in length are feasible.

Huff, R. G.↗

NASA NTRS1973

An experimental investigation of two-phase liquid oxygen pumping

The results of an experimental program to explore the feasibility of pumping two-phase oxygen (liquid and gas) at the pump inlet are reported. Twenty-one cavitation tests were run on a standard J-2 oxygen pump at the MSFC Components Test Laboratory. All tests were run with liquid oxygen 5 to 10 K above the normal boiling point temperature. During ten tests run at approximately at the pump inlet were noted before complete pump performance 50 percent of the nominal operating speed, two phase conditions were achieved. Vapor volumes of 40 to 50 percent at the pump inlet were noted before complete pump performance loss. The experimental results compared to predictions. Nine cavitation tests run at the nominal pump speed over a 5 K temperature range showed progressively lower net positive suction head (NPSH) requirements as temperature was increased. Two-phase operation was not achieved. The temperature varying NPSH data were used to calculate thermodynamic effects on NPSH, and the results were compared to existing data.

Gross, L. A.↗

NASA NTRS1974

Automated microbial metabolism laboratory

The design and rationale of an advanced labeled release experiment based on single addition of soil and multiple sequential additions of media into each of four test chambers are outlined. The feasibility for multiple addition tests was established and various details of the methodology were studied. The four chamber battery of tests include: (1) determination of the effect of various atmospheric gases and selection of that gas which produces an optimum response; (2) determination of the effect of incubation temperature and selection of the optimum temperature for performing Martian biochemical tests; (3) sterile soil is dosed with a battery of C-14 labeled substrates and subjected to experimental temperature range; and (4) determination of the possible inhibitory effects of water on Martian organisms is performed initially by dosing with 0.01 ml and 0.5 ml of medium, respectively. A series of specifically labeled substrates are then added to obtain patterns in metabolic 14CO2 (C-14)O2 evolution.

Source record↗

NASA NTRS1975

Gravitational theories with nonzero divergence of the energy-momentum tensor

Assuming that the divergence of the energy-momentum tensor is nonzero leads to a class of theories with consistent field equations and gauge conditions as well as compatibility with the Newtonian limit of the conservation laws. Both the Einstein and the Brans-Dicke theories are used as models, but the extension to other viable theories such as vector-metric and two-metric theories is possible. One particularly interesting theory emerges that agrees with the ordinary Brans-Dicke theory except for the post-Newtonian parameter zeta sub 2, which predicts nonconservation of total momentum. Unfortunately, no accurate experimental limits for this parameter are known. It thus remains for future experiments in lunar-laser ranging to test this theory.

Smalley, L. L.↗

NASA NTRS1976

Correlation microphone for measuring airframe noise in large-scale wind tunnels

A correlation microphone arrangement was used in the test section of the Ames 7- by 10-Foot and 40- by 80-Foot Wind Tunnels in an attempt to reject the reverberant and wind noise. The tests in the 7- by 10-foot wind tunnel covered a frequency range from 400 Hz to 8 kHz while the tests in the 40- by 80-foot tunnel covered the range from 31.5 to 800 Hz. Examination of the experimental data plus calculations of cross-correlations due to reflective noise indicate that the correlation microphone is effective in rejecting microphone wind noise and reverberant noise even at low frequencies, and that the low-frequency background noise monitored by the correlation microphone is reflected noise with a preferred direction from the tunnel drive system. Design studies indicate that this tunnel drive noise can be reduced substantially through suitable modification of the drive fans and acoustical treatment of the nacelles that house these fans.

Ahtye, W. F.↗

NASA NTRS1979

Experimental study of coaxial nozzle exhaust noise

Experimental results are presented for static acoustic model tests of various geometrical configurations of coaxial nozzles operating over a range of flow conditions. The geometrical configurations consisted of nozzles with coplanar and non-coplanar exit planes and various exhaust area ratios. Primary and secondary nozzle flows were varied independently over a range of nozzle pressure ratios from 1.4 to 3.0 and gas temperatures from 280 to 1100 K. Acoustic data are presented for the conventional mode of coaxial nozzle operation as well as for the inverted velocity profile mode. Comparisons are presented to show the effect of configuration and flow changes on the acoustic characteristics of the nozzles.

Goodykoontz, J. H.↗

NASA NTRS1979

Long-term temperature effects on GaAs solar cells

The thermal degradation of AlGaAs solar cells resulting from a long-term operation in a space environment is investigated. The solar cell degradation effects caused by zinc and aluminum diffusion as well as deterioration by arsenic evaporation are presented. Also, the results are presented of experimental testing and measurements of various GaAs solar cell properties while the solar cell was operating in the temperature range of 27 C to 350 C. In particular, the properties of light current voltage curves, dark current voltage curves, and spectral response characteristics are given. Finally, some theoretical models for the annealing of radiation damage over various times and temperatures are included.

Heinbockel, J. H.↗

NASA NTRS1979

Experimental study of coaxial nozzle exhaust noise

Goodykoontz, J. H.↗

NASA NTRS1984

The case for antiparticles in the extragalactic cosmic radiation

The presence of an excess of low energy antiprotons in the primary cosmic radiation has given rise to a number of possible explanations. The possibility that these are extragalactic in origin is considered and it is shown that there are interesting implications for the bulk of the cosmic radiation at higher energies. In particular, it may be possible to account for a previously puzzling feature, a bump in the cosmic ray energy spectrum in the energy range 10(14) to 10(15) eV, with this primary extragalactic origin hypothesis. A method for testing this hypothesis experimentally is also described.

Stecker, F. W.↗

NASA NTRS1984

Prediction of transonic separated flows

Johnson et al. (1982) have provided a detailed comparison between a thoroughly documented transonic flow with shock-induced separations and solutions of the flow using the Navier-Stokes equations. According to this comparison, there were several deficiencies in the computations. The present investigation takes into account new experimental data which have been obtained in a larger wind tunnel with the same test model for a wider range of freestream Mach numbers. The results of new Navier-Stokes computations using more compatible boundary conditions are shown, and the effects of the turbulence model choice on predicting Mach number trends are assessed.

Horstman, C. C.↗

NASA NTRS1986

Passive eddy-current damping as a means of vibration control in cryogenic turbomachinery

Lateral shaft vibrations produced by a rotating unbalance weight were damped by means of eddy currents generated in copper conductors that were precessing cyclicly in the gap formed by the pole faces of C-shaped, permanent magnets. The damper assembly, which was located at the lower bearing support of a vertically oriented rotor was completely immersed in liquid nitrogen during the test run. The test rotor was operated over a speed range from 800 to 10,000 rpm. Three magnet/conductor designs were evaluated. Experimental damping coefficients varied from 180 to 530 N sec/m. Reasonable agreement was noted for theoretical values of damping for these same assemblies. Values of damping coefficients varied from 150 to 780 N sec/m. The results demonstrate that passive eddy-current damping is a viable candidate for vibration control in cryogenic turbomachinery.

Cunningham, R. E.↗

NASA NTRS1986

Using the IRAS data to search in the asteroid belt for any potential evidence of galactic colonization

The end product of the biological evolution seems to be the appearance of technological civilizations, which are characterized by superior technology that supercedes biological capabilities. The Search for Extraterrestrial Intelligence (SETI) has gained scientific recognition in recent years. The concept of galactic colonization is debated extensively, with opinions ranging from the impossible to the inevitable, but without a clear resolution. Answers can be obtained only with experimental tests and not with endless debates. A search for large space colonies in the asteroid belt, an ideal source of raw materials for a spaceborne civilization, is a test of the galactic colonization theory. The catalogue of solar system objects obtained form the Infrared Astronomy Satellite (IRAS) observations at 12, 25, 60, and 100 microns, is an ideal source for such a search. The catalog is expected to be ready at the end of 1985 and will contain more than 10,000 objects.

Papagiannis, M. D.↗

NASA NTRS1987

Size and Shape of Solid Fuel Diffusion Flames in Very Low Speed Flows

The effect of very low speed forced flows on the size and shape of a solid fuel diffusion flame are investigated experimentally. Flows due to natural convection are eliminated by performing the experiment in low gravity. The range of velocities tested is 1.5 cm/s to 6.3 cm/s and the mole fraction of oxygen in the O2/N2 atmosphere ranges from 0.15 to 0.19. The flames did not reach steady state in the 5.2 sec to which the experiment was limited. Despite limited data, trends in the transient flame temperature and, by means of extrapolation, the steady state flame size are deduced. As the flow velocity is reduced, the flames move farther from the fuel surface, and the transient flame temperature is lowered. As the oxygen concentration is reduced the flames move closer to the fuel sample and the transient flame temperature is reduced. With stand off distances up to 8.5 + or - 0.7 mm and thicknesses around 1 or 2 mm, these flames are much weaker than flames observed at normal gravity. Based on the performance of the equipment and several qualitative observations, suggestions for future work are made.

Foutch, David W.↗

NASA NTRS1991

Aeroacoustic flow sensor

A theoretical analysis of standing waves in a pipe with flow was conducted aimed toward the development of a flowmeter based on a measurement of phase difference between two points on the circumference of a pipe separated axially by an integral multiple of half sound wavelength. Effects of nonzero Mach number, variable ratios of upstream and downstream running waves, choice of location of the sensing pressure taps, and the incorrect spacings were examined numerically. Calculations were also made for steam flow where the maximum Mach number is much smaller than in cold air flows. For an industrial application where steam flow velocities are below 50 m/s, a very accurate sensor is shown to be possible. Experimental data were obtained by using an active aeroacoustic source over the range of 50 m/s to zero in an air flow. Experimental phase plots obtained from several coast-down tests have been compared with analytical results. The agreement with theory is excellent when the spacings are near N(lambda)/2 and the sensing locations are near the pressure antinodes. Otherwise, some zero shifts are introduced. Theory predicts that for steam flow much better results can be expected because the maximum Mach number is much smaller. Effects due to the (1-M-squared) factor would be imperceptible for steam flow.

Shakkottai, P.↗

NASA NTRS1993

Applying and validating the RANS-3D flow-solver for evaluating a subsonic serpentine diffuser geometry

Subsonic inlet ducts for advanced, high-performance aircraft are evolving towards complex three-dimensional shapes for reasons of overall integration and weight. These factors lead to diffuser geometries that may sacrifice inlet performance, unless careful attention to design details and boundary layer management techniques are employed. The ability of viscous computational fluid dynamic (CFD) analysis of such geometries to aid the aircraft configurator in this complex design problem is herein examined. The RANS-3D Reynolds-Averaged Navier-Stokes solver is applied to model the complex flowfield occurring in a representative diffuser geometry and the solutions are compared to experimental results from a static test of the inlet duct. The computational results are shown to compare very favorably with experimental results over a range of mass flow rates, including those involving large amounts of separation in the diffuser. In addition, a novel grid topology is presented, and two turbulence models are evaluated in this study as part of the RANS-3D code.

Fletcher, Michael J.↗