Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLAT PLATE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

A method for measuring skin friction drag on a flat plate in contaminated gas flows

A technique for measuring friction drag in turbulent gas and gas/particle flows over flat plates is presented, and preliminary results are reported. A 0.25-in.-thick 72 x 6-in. Al plate is suspended by six horizontal support air bearings and four vertical alignment air bearings between fixed dummy plates and leading-edge and trailing-edge fairings in the 32-in.-high 48-in.-wide 11-ft-long test section of a closed-circuit atmospheric wind tunnel operating at 50-150 ft/sec. Particles of Fe and Al oxides of diameter 20-150 microns and density up to 0.3 lb particles per lb air are injected via a 6 x 0.167-in. nozzle; turbulence is induced by a roughened section of the leading-edge fairing; and friction drag is measured using a load-cell pressure transducer. Sample results are shown in a graph, demonstrating good agreement with theoretical drag calculations.

Oetting, R. B.↗
NASA NTRS1938

A preliminary investigation of boundary-layer transition along a flat plate with adverse pressure gradient

Boundary-layer surveys were made throughout the transition region along a smooth flat plate placed in an airstream of practically zero turbulence and with an adverse pressure gradient. The boundary-layer Reynolds number at the laminar separation point was varied from 1,800 to 2,600. The test data, when considered in the light of certain theoretical deductions, indicated that transition probably began with separation of the laminar boundary layer. The extent of the transition region, defined as the distance from a calculated laminar separation point to the position of the first fully developed turbulent boundary-layer profile, could be expressed as a constant Reynolds number run of approximately 70,000. Some speculations are presented concerning the application of the foregoing concepts, after certain assumptions have been made, to the problem of the connection between transition on the upper surface of an airfoil at high angles of attack and the maximum lift.

Von Doenhoff, Albert E↗
NASA NTRS1972

Transient-forced convection film boiling on an isothermal flat plate.

Development of a new approach for the solution of transient-forced convection film boiling on an isothermal flat plate using the boundary layer model. The similarity variables are used to convert the governing partial differential equations to ordinary ones. The results of numerical solutions of these ordinary equations indicate that the transient process can be classified as one-dimensional conduction, intermediate, and the steady-state regions. The time required for the one-dimensional conduction and the time necessary to attain a steady-state condition are obtained. The use of local similarity approximations for the intermediate regime facilitates prediction of complete boundary layer growth. Using the ratio of time at any instant to the steady-state time as abscissa, the curves representing the boundary layer growth can be merged into a single mean curve within 5%. Further, the analysis shows that the average rate of heat transfer during transient is 50 to 100% higher than those at steady state. The average rate of vapor convected away is 10 to 15% lower than at steady state while the average rate of accumulation to form the vapor layer is 1 to 14 times larger.

Nagendra, H. R.↗
NASA NTRS1979

Hot-air flat-plate solar collector-design package

Report contains design data, performance specifications, and drawings for hot-air flat-plate solar-energy collector. Evaluation consists of tests on thermal performance time constance, and incidence angle modifier test. Results are presented in table and graph form and are analyzed in detail.

Source record↗
NASA NTRS1984

Heat transfer from impinging jets to a flat plate with conical and ring protuberances

An experimental investigation of heat transfer from round jets, impinging normally on a flat plate with exchangeable, heat transfer enhancing protuberances, has been carried out, and the pertinent literature surveyed, for Reynolds numbers ranging from 14,000 to 67,000, and nozzle diameters from 3.18 to 9.52 mm. The experimental data at the stagnation point indicated laminar flow, and a significant enhancement of heat transfer there, due to the introduction of the spike protuberance; the ring protuberance reduced the local heat flux somewhat. Data have also been correlated by means of dimensional analysis and compared with the conical flow theory.

Hrycak, P.↗
NASA NTRS1986

Flat-plate solar array project. Volume 2: Silicon material

The goal of the Silicon Material Task, a part of the Flat Plate Solar Array (FSA) Project, was to develop and demonstate the technology for the low cost production of silicon of suitable purity to be used as the basic material for the manufacture of terrestrial photovoltaic solar cells. Summarized are 11 different processes for the production of silicon that were investigated and developed to varying extent by industrial, university, and Government researchers. The silane production section of the Union Carbide Corp. (UCC) silane process was developed completely in this program. Coupled with Siemens-type chemical vapor deposition reactors, the process was carried through the pilot stage. The overall UCC process involves the conversion of metallurgical-grade silicon to silane followed by decomposition of the silane to purified silicon. The other process developments are described to varying extents. Studies are reported on the effects of impurities in silicon on both silicon-material properties and on solar cell performance. These studies on the effects of impurities yielded extensive information and models for relating specific elemental concentrations to levels of deleterious effects.

Lutwack, R.↗
NASA NTRS1989

Fluctuating pressures measured beneath a high-temperature, turbulent boundary layer on a flat plate at Mach number of 5

Fluctuating pressures were measured beneath a Mach 5, turbulent boundary layer on a flat plate with an array of piezoresistive sensors. The data were obtained with a digital signal acquisition system during a test run of 4 seconds. Data sampling rate was such that frequency analysis up to 62.5 kHz could be performed. To assess in situ frequency response of the sensors, a specially designed waveguide calibration system was employed to measure transfer functions of all sensors and related instrumentation. Pressure time histories were approximated well by a Gaussian prohibiting distribution. Pressure spectra were very repeatable over the array span of 76 mm. Total rms pressures ranged from 0.0017 to 0.0046 of the freestream dynamic pressure. Streamwise, space-time correlations exhibited expected decaying behavior of a turbulence generated pressure field. Average convection speed was 0.87 of freestream velocity. The trendless behavior with sensor separation indicated possible systematic errors.

Parrott, Tony L.↗
NASA NTRS1991

Experimental study of boundary layer transition with elevated freestream turbulence on a heated flat plate

A detailed investigation to document momentum and thermal development of boundary layers undergoing natural transition on a heated flat plate was performed. Experimental results of both overall and conditionally sampled characteristics of laminar, transitional, and low Reynolds number turbulent boundary layers are presented. Measurements were acquired in a low-speed, closed-loop wind tunnel with a freestream velocity of 100 ft/s and zero pressure gradient over a range of freestream turbulence intensities (TI) from 0.4 to 6 percent. The distributions of skin friction, heat transfer rate and Reynolds shear stress were all consistent with previously published data. Reynolds analogy factors for R(sub theta) is less than 2300 were found to be well predicted by laminar and turbulent correlations which accounted for an unheated starting length. The measured laminar value of Reynolds analogy factor was as much as 53 percent higher than the Pr(sup -2/3). A small dependence of turbulent results on TI was observed. Conditional sampling performed in the transitional boundary layer indicated the existence of a near-wall drop in intermittency, pronounced at certain low intermittencies, which is consistent with the cross-sectional shape of turbulent spots observed by others. Non-turbulent intervals were observed to possess large magnitudes of near-wall unsteadiness and turbulent intervals had peak values as much as 50 percent higher than were measured at fully turbulent stations. Non-turbulent and turbulent profiles in transitional boundary layers cannot be simply treated as Blasius and fully turbulent profiles, respectively. The boundary layer spectra indicate predicted selective amplification of T-S waves for TI is approximately 0.4 percent. However, for TI is approximately 0.8 and 1.1 percent, T-S waves are localized very near the wall and do not play a dominant role in transition process.

Sohn, Ki-Hyeon↗
NASA NTRS1995

The pressure field of a gust interacting with a flat plate

A semianalytical solution is presented for the unsteady pressure field of a vortical gust interacting with a flat-plate airfoil in subsonic flow. The solution will serve as a benchmark for evaluating the accuracy and efficiency of time dependent numerical schemes. The specific case considered corresponds to the ICASE benchmark problem number 6. The results are compared with those of asymptotic theories for high frequency and show excellent agreement.

Atassi, Hafiz M.↗
NASA NTRSDate not supplied

Instabilities in the Wake of a Pseudorandom Roughness on a Supersonic Flat Plate

A roughness patch defined by a two-dimensional Fourier series was installed in a highly-polished flat plate model immersed in a supersonic quiet flow. The NASA Langley Research Center Supersonic Low Disturbance Tunnel is capable of providing a Mach 3.5 flow with low freestream acoustic noise and low turbulence levels. Measurements made with a hot-wire probe downstream of the roughness element showed the presence of instability modes that did not cause transition in the measurement region at a freestream unit Reynolds number of Re =12.6×10^6/m. The largest amplitude mode appeared to be similar to a symmetric mode. The same roughness patch immersed in a higher freestream acoustic noise environment showed little to no evidence of the instability modes. Instead, disturbances found in the boundary layer matched closely to the freestream spectra measured in the empty tunnel under the same conditions, indicating some evidence of freestream forcing in the boundary layer.

Roughness induced transition↗
NASA NTRS2022

Instabilities in the Wake of a Pseudorandom Roughness on a Supersonic Flat Plate

A roughness patch defined by a two-dimensional Fourier series was installed in a highly-polished flat plate model immersed in a supersonic quiet flow. The NASA Langley Research Center Supersonic Low Disturbance Tunnel is capable of providing a Mach 3.5 flow with low freestream acoustic noise and low turbulence levels. Measurements made with a hot-wire probe downstream of the roughness element showed the presence of instability modes that did not cause transition in the measurement region at a freestream unit Reynolds number of Re =12.6×10^6/m. The largest amplitude mode appeared to be similar to a symmetric mode. The same roughness patch immersed in a higher freestream acoustic noise environment showed little to no evidence of the instability modes. Instead, disturbances found in the boundary layer matched closely to the freestream spectra measured in the empty tunnel under the same conditions, indicating some evidence of freestream forcing in the boundary layer.

Roughness induced transition↗
NASA NTRS2022

Instabilities in the Wake of a Pseudorandom Roughness on a Supersonic Flat Plate

A roughness patch defined by a two-dimensional Fourier series was installed in a highly-polished flat plate model immersed in a supersonic quiet flow. The NASA Langley Research Center Supersonic Low Disturbance Tunnel is capable of providing a Mach 3.5 flow with low freestream acoustic noise and low turbulence levels. Measurements made with a hot-wire probe downstream of the roughness element showed the presence of instability modes that did not cause transition in the measurement region at a freestream unit Reynolds number of Re =12.6×10^6/m. The largest amplitude mode appeared to be similar to a symmetric mode. The same roughness patch immersed in a higher freestream acoustic noise environment showed little to no evidence of the instability modes. Instead, disturbances found in the boundary layer matched closely to the freestream spectra measured in the empty tunnel under the same conditions, indicating some evidence of freestream forcing in the boundary layer.

Roughness induced transition↗
NASA NTRS1974

An eddy-viscosity treatment of the unsteady turbulent boundary layer on a flat plate in an expansion tube

An analysis is presented for the relaxation of a turbulent boundary layer on a semiinfinite flat plate after passage of a shock wave and a trailing driver gas-driven gas interface. The problem has special application to expansion tube flows. The flow-governing equations have been transformed into the Lamcrocco variables. The numerical results indicate that a fully turbulent boundary layer relaxes faster to the final steady-state values of heat transfer and skin-friction than a fully laminar boundary layer.

Gupta, R. N.↗
NASA NTRS1977

Velocity and temperature profiles in near-critical nitrogen flowing past a horizontal flat plate

Boundary layer velocity and temperature profiles were measured for nitrogen near its thermodynamic critical point flowing past a horizontal flat plate. The results were compared measurements made for vertically upward flow. The boundary layer temperatures ranged from below to above the thermodynamic critical temperature. For wall temperatures below the thermodynamic critical temperature there was little variation between the velocity and temperature profiles in three orientations. In all three orientations the point of crossing into the critical temperature region is marked by a significant flattening of the velocity and temperature profiles and also a decrease in heat transfer coefficient.

Simoneau, R. J.↗
NASA NTRS1977

Velocity and temperature profiles in near-critical nitrogen flowing past a horizontal flat plate

Boundary layer velocity and temperature profiles were measured for nitrogen near its thermodynamic critical point flowing past a horizontal flat plate. The heated surface was oriented both facing upward and downward. The results were compared to earlier work in which measurements were made for vertically upward flow. The boundary layer temperatures ranged from below to above the thermodynamic critical temperature. For wall temperatures below the thermodynamic critical temperature there was little variation between the velocity and temperature profiles in the three orientations. In all three orientations the point of crossing into the critical temperature region is marked by a significant flattening of the velocity and temperature profiles and also a decrease in heat transfer coefficient. As the heat flux and, consequently, wall temperature are further increased significant changes occur in the velocity and temperature profiles. Examination of near-critical heat transfer in these three flow orientations offers insights into the relative role of buoyancy forces in this regime.

Simoneau, R. J.↗