Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

The Evolution of LiNi 0.5 Mn 0.3 Co 0.2 O 2 Particle Damage from Fast Charging in Optimized, Full Li-Ion Cells

Fast charging batteries are critical to the widespread adoption of electric vehicles to compete with refueling times of combustion-based vehicles. In the near term, adapting current commercial battery technologies to perform better under fast charging conditions through engineering optimizations will greatly expedite the process while exploratory fast-charging electrode materials are being pursued. To do so, the degradation modes in optimized Li-ion batteries need to be completely explored to understand fast charging limits while maintaining a high energy density and a long cycle life. While lithium plating on graphite still remains a challenge, cathode degradation also plays a key role in battery performance. In this work, we used nano- and micro-X-ray computed tomography to characterize the mechanical degradation of LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC532) in optimized Li-ion batteries cycled at three rates, 1C, 6C, and 9C, and at different stages of cycle life, 225 and 600 cycles. We report despite using a conservative upper voltage cutoff limit aimed to minimize extensive cathode degradation, higher charging rates and increased cycling caused the polycrystalline NMC532 particles to fracture and pulverize, which likely drives cathode capacity fade and contributes to the decrease in overall cell performance.

25 ENERGY STORAGE↗
DOE OSTI2023

Degradation in Ni-Rich LiNi 1– x – y Mn x Co y O 2 /Graphite Batteries: Impact of Charge Voltage and Ni Content

Ni-rich LiNi 1– x–y Mn x CoyO 2 (NMC) materials are attractive as cathodes for Li-ion batteries due to their high energy density and low Co content. However, these materials may display poor electrochemical reversibility relating to structural and interfacial instabilities. The influence of Ni content and level of delithiation during charge on degradation mechanisms and relevance to electrochemical cycling behavior are probed for LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) and LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) cathode materials in a full cell configuration under two upper voltage limits (4.1 and 4.3 V). The combined use of dQ/dV analysis of electrochemical voltage profiles, operando XRD, and postcycling scanning electron microscopy (SEM) measurements indicates that a major contributor to capacity fade is the large anisotropic volume change from an H2 $\leftrightarrows$ H3 phase transition and associated mechanical degradation particularly for NMC811. Notably, transition metal dissolution and deposition on the negative electrode are found to correlate with the structural changes occurring in the cathode under high voltage charge. X-ray photoelectron spectroscopy (XPS) analyses of the cycled cathodes reveal a more organic-rich cathode–electrolyte interphase (CEI) when cycling to 4.3 V with lower relative amounts of LiF. Surface reconstruction is not a significant factor under these cycling conditions as determined by soft X-ray absorption spectroscopy (sXAS) analysis. The results emphasize the opportunity to match the electrochemical test parameters with the specific NMC active material to mitigate degradation and extend cycle life.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Automatic Generation of Chemical Mechanisms for Electrochemical Systems: Solid Electrolyte Interphase Formation in Lithium Batteries

Electrolytes in many lithium ion batteries decompose at the low potentials near the anode. The decomposition products form a layer termed the solid electrolyte interphase (SEI). The composition and growth of the SEI layer significantly affect both the capacity fade and safety of lithium ion batteries. However, SEI formation and growth kinetics are not well understood. In this work, we present an extension of the Reaction Mechanism Generator (RMG) software to automatically generate mechanisms for SEI formation. We extend RMG’s solvation correction framework to account for kinetic solvent effects and demonstrate the accuracy of our technique. We calculate thermochemical parameters for 252 species and rate coefficients for 69 reactions, most with associated solvation corrections. This and additional quantum chemistry data are used to extend RMG’s thermodynamic group additivity and solute parameter estimation schemes to handle lithiated species and add 14 new reaction families to RMG. RMG is additionally extended to simulate electrocatalytic systems. Lastly, we demonstrate RMG on the decomposition of acetonitrile and ethylene carbonate near a battery anode. Furthermore, while this framework does not yet resolve individual ions, as appropriate thermochemistry estimators are not available, and thus, cannot yet resolve more complex electrochemical pathways, RMG is able to generate reasonable pathways for SEI formation that match literature pathways and products. In particular, RMG identifies a new important reaction pathway that is not present in literature.

Chemical reactions↗
DOE OSTI2021

Chemomechanically Stable Ultrahigh-Ni Single-Crystalline Cathodes with Improved Oxygen Retention and Delayed Phase Degradations

The pressing demand in electrical vehicle (EV) markets for high-energy-density lithium-ion batteries (LIBs) requires further increasing the Ni content in high-Ni and low-Co cathodes. However, the commercialization of high-Ni cathodes is hindered by their intrinsic chemomechanical instabilities and fast capacity fade. The emerging single-crystalline strategy offers a promising solution, yet the operation and degradation mechanism of single-crystalline cathodes remain elusive, especially in the extremely challenging ultrahigh-Ni (Ni > 90%) regime whereby the phase transformation, oxygen loss, and mechanical instability are exacerbated with increased Ni content. Herein, we decipher the atomic-scale stabilization mechanism controlling the enhanced cycling performance of an ultrahigh-Ni single-crystalline cathode. We find that the charge/discharge inhomogeneity, the intergranular cracking, and oxygen-loss-related phase degradations that are prominent in ultrahigh-Ni polycrystalline cathodes are considerably suppressed in their single-crystalline counterparts, leading to improved chemomechanical and cycling stabilities of the single-crystalline cathodes. Furthermore, our work offers important guidance for designing next-generation single-crystalline cathodes for high-capacity, long-life LIBs.

25 ENERGY STORAGE↗
DOE OSTI2022

Accelerated Degradation in a Quasi-Single-Crystalline Layered Oxide Cathode for Lithium-Ion Batteries Caused by Residual Grain Boundaries

The rapidly growing demand of electrical vehicle (EV) requires high-energy-density lithium-ion batteries (LIBs) with excellent cycling stability and safety performance. However, conventional polycrystalline high-Ni cathodes severely suffer from intrinsic chemo-mechanical degradation and fast capacity fade. The emerging single-crystallization strategy offers a promising pathway to improve the chemo-mechanical stability, however, the single-crystallinity of the cathode is not always guaranteed and residual grain boundaries (GBs) could persist in nonideal synthesis conditions, leading to the formation of ‘quasi’ single-crystalline (QSC) cathodes. So far, there is a lack of understanding of the influence of these residual GBs on the electrochemical performance and structural stability. Herein, we investigate the degradation pathway of a QSC high-Ni cathode through transmission electron microscopy and X-ray techniques. The residual GBs caused by insufficient calcination time, dramatically exacerbate the cathode’s chemo-mechanical instability and cycling performance. Our work offers important guidance for the next-generation cathodes for long-life LIBs.

25 ENERGY STORAGE↗
DOE OSTI2022

Porosity Development at Li-Rich Layered Cathodes in All-Solid-State Battery during In Situ Delithiation

Structural evolutions are crucial for determining the performance of high-voltage lithium, manganese-rich layered cathodes. Moreover, interface between electrode and electrolyte plays a critical role in governing ionic transfer in all-solid-state batteries. In this work, we unveil two different types of porous structure in Li 1.2 Ni 0.2 Mn 0.6 O 2 cathode with LiPON solid-state electrolyte. Na-nopores are found near the cathode/electrolyte interface at pristine state, where cation mixing, phase transformation, oxygen loss and Mn reduction are also found. In situ Li + extraction induces the evolution of nanovoids, initially formed near the inter-face then propagated into the bulk. Despite the development of nanovoids, layered structure is conserved, suggesting the nature of nanopores and nanovoids are different and their impact would be divergent. This work demonstrates the intrinsic interfacial layer, as well as the dynamic scenario of nanovoid formation inside high-capacity layered cathode, which help understanding the performance fading in cathodes and offer insights into the all-solid-state battery design.

25 ENERGY STORAGE↗
DOE OSTI2020

Revealing the Structural Evolution and Phase Transformation of O3-Type NaNi 1/3 Fe 1/3 Mn 1/3 O 2 Cathode Material on Sintering and Cycling Processes

O-type layered oxide cathode materials can be easily synthesized for a full sodium stoichiometry with high specific capacity, but they all suffer from a capacity fade on cycling. The sintering process control and optimization are critical to ensure a high quality and consistency of the prepared cathode materials with stable structure. Herein, in situ high-energy X-ray diffraction (HEXRD) was first employed to investigate the phase evolution of the oxides during the sintering process of O3-type NaNi 1/3 Fe 1/3 Mn 1/3 O 2 . The in situ HEXRD and both operando Bragg coherent diffraction (BCXD) and coherent multicrystal diffraction (CMCD) were utilized to investigate the phase transformation of the cathode materials during the sodiation/desodiation process. A composite structure comprised of O-type and P-type oxides was formed after the initial electrochemical activation of the cathode material, resulting in good structural and electrochemical stability. This finding implies that strain engineering can be a new design philosophy for the development of next generation high-performance sodium ion cathodes.

25 ENERGY STORAGE↗
DOE OSTI2020

Understanding Reactivities of Ni-rich Li[NixMnyCo1-x-y]O2 Single-Crystal Cathode Materials

While Ni-rich Li[NixMnyCo1-x-y]O2 (NMC, x ? 0.8) compounds are considered the most promising cathode materials for high-energy lithium-ion batteries (LIBs), a significant challenge is the higher reactivities caused by the increased Ni content, especially under high-voltage operation conditions. In the present study, we synthesize three single-crystal NMC (SC-NMC) samples with the same particle size and morphology: LiNi0.8Mn0.1Co0.1O2 (NMC811), LiNi0.80Mn0.15Co0.05O2 (NMC80155) and LiNi0.85Mn0.10Co0.05O2 (NMC85105). By systematically varying the composition while controlling other properties, the role of each transition metal during air exposure, thermal treatment and long-term cycling is clearly demonstrated. We reveal that while higher Ni content leads to an overall increased reactivities, the presence of Mn provides a stabilizing effect on thermal, structural and chemical properties. In the absence of cycling-induced particle cracking, surface reconstruction is shown to be the dominating contributor to cathode capacity fade. Our study provides key insights needed for the development of better-performing Ni-rich NMC cathode materials.

Kim, Minkyung↗
DOE OSTI2021

Large Scale Synthesis of Manganese Oxide/Reduced Graphene Oxide Composites as Anode Materials for Long Cycle Lithium Ion Batteries

Manganese oxides have been frequently used as cathodes in primary batteries. Applications of manganese oxides in secondary batteries are limited by low electrical conductivity and rapid capacity fading because of electrode pulverization and aggregation. In this study, a solid-state synthetic strategy is presented that successfully combines nanosize (~ 50 nm) nickel doped α-MnO 2 with reduced graphene oxides as highly stable composite anodes in lithium ion batteries. The synthesis approach is easy to scale up and suitable for industrial applications. Here, the rationally designed Ni-α-MnO 2 /RGO was tested in galvanostatic half coin cells for Li + charge-discharge studies. The results show that this composite maintains a high capacity of 615 mAh g -1 even after 200 cycles at a high current rate of 1 C (830 mA g -1 ), and with a high Coulombic efficiency near 99%. The anodes exhibit excellent rate capability in a wide range of rate testing from 0.2 to 10 C, without showing capacity decay. This superior anode performance is ascribed to the reduced size of α-MnO 2 domains that are well dispersed in an RGO matrix, which affords good ionic/elec. cond., low charge transfer resistance and mitigates issues of vol. expansion of the anodic active materials. This study opens up an avenue for developing the manufacturing of high-performance electrodes for real applications, such as batteries in electrical vehicles.

25 ENERGY STORAGE↗
DOE OSTI2021

Stress-Dependent Chemo-Mechanical Performance of Amorphous Si Anodes for Li-Ion Batteries upon Lithiation

Alloying-type anodes are significantly governed by their chemo-mechanical performance during the electrochemical cycling. The reaction-induced huge volumetric change of these anodes may cause material degradation and failure under mechanical constraints. Here, we investigate the stress-dependent lithiation behavior of amorphous Si (a-Si) anodes using molecular dynamics simulations. It is indicated that a-Si anodes can sustain higher hydrostatic stress than biaxial/uniaxial ones without the occurrence of mechanical failure. Thermodynamic and electrochemical calculations demonstrate that although the lithiation procedure also affects the thermodynamic stability of a-Si anodes, it is mainly dominated by the external mean stresses. Compressive stress is confirmed to destabilize a-Si anodes and further trigger their capacity fading. Compared with our atomistic simulations, previous continuum models underestimate the open-cell potentials of a-Si anodes, due to their ignored large volumetric deformation at higher stresses and Li concentrations. Finally, this computational study provides the intensive atomic-level understanding of the stress-dependent lithiation behavior of a-Si anodes.

25 ENERGY STORAGE↗
DOE OSTI2023

An Extremely Stable and Soluble NH 2 -Substituted Anthraquinone Electrolyte for Aqueous Redox Flow Batteries

Aqueous redox flow batteries require long-term stable redox molecules for electrical energy storage. Anthraquinones, especially ether bond-decorated ones, experience two dominant decomposition pathways, including side-chain loss and anthrone formation. Here, with the aid of DFT calculations, we designed an anthraquinone (3-NH 2 -2-2PEAQ) bearing an ether substituent and a neighboring NH 2 group, which suppresses both of these decomposition mechanisms and exhibits a high solubility of 1.1 M. When paired with ferrocyanide in a full cell, this anthraquinone, at a concentration of 1.0 M, can operate at greater than 1 V with an extremely low capacity fade rate of 0.01%/day and a Coulombic efficiency above 99.8% while cycling for over a month. The synergistic effects of the ether and parent amino substituents are extremely sensitive to the precise substitution pattern of the anthraquinone. This study demonstrates the effectiveness of the judicious use of DFT-based prediction in rapidly identifying promising candidate electrolytes from a large chemical space.

25 ENERGY STORAGE↗
DOE OSTI2024

Electrochemical and Chemical Reactivities of Titanium Oxide-Based Materials with a Chloroaluminate Ionic Liquid Electrolyte for Aluminum Batteries

Here, by selecting three different types of electrode materials, we intended to better understand the Al 3+ intercalation chemistry of titanium oxide-based frameworks with an acidic chloroaluminate electrolyte. In agreement with previous reports, we confirmed that the native interstitial sites of anatase TiO 2 are less prone to accommodate Al 3 + than Li + or Na + ions, while introducing cationic vacancies largely increases the electrochemical storage capacity. Upon the first cycle, the highest reversible capacity, up to 277 mAh/g, was obtained for a hydrated layered structure featuring cationic vacancies. Total scattering data showed that the insertion of Al 3+ ions induced a strong distortion of the framework. In addition, combined 27 Al MAS NMR and DFT calculations revealed that in oxy-hydroxylated vacant sites, the coordination mode of Al 3+ ions depends on the arrangement of anions around vacancies inducing the occurrence of 4-, 5-, and 6-fold coordination modes. Further cycling experiments revealed a progressive capacity fading for all electrode materials. Using cyclic voltammetry on the used electrolyte, we evidenced that a partial dissolution has occurred, which is more pronounced for the layered hydrate compound, and that solubilized species are electrochemically active, giving rise to specific signatures in both CVs and galvanostatic experiments. Raman spectroscopy enabled us to characterize these species, which are derived from the Ti-Cl system. The solubilized species, however, eventually precipitated, as shown by a purple deposit observed on the separator and tentatively assigned to TiCl 3 , known to be insoluble in this medium. By providing further information on the Al 3+ intercalation chemistry and a better understanding of the electrochemical and chemical reactivities of electrode materials, this work will enable progress to be made in the development of aluminum-ion batteries.

Al3+-ion insertion chemistry↗
DOE OSTI2024

Multinonmetal-Doped V 2 O 5 Nanocomposites for Lithium-Ion Battery Cathodes

Lithium-ion batteries (LIBs) are critical for portable electronics and electric vehicles, demanding higher energy density to meet increasing energy storage needs. Current commercial cathode materials, such as LiFePO 4 and LiCoO 2 , are limited by a single electron transfer, restricting their energy density. Vanadium pentoxide (V 2 O 5 ) emerges as a promising high-capacity cathode due to its high theoretical capacity of 443 mA h g –1 with three Li storage capacities, significantly surpassing conventional materials. However, the practical application of V 2 O 5 is hindered by a large structural evolution and rapid capacity fading during full lithium intercalation. Here, this study introduces a multinonmetal doping (MNM) strategy to enhance V 2 O 5 cathodes by incorporating all-nonmetal dopants (B, P, and Si) and graphene (G). MNM-V 2 O 5 -G exhibits increased surface oxygen defects, improving charge transfer kinetics and thus enhancing the rate performance and cycling stability. Our results provide valuable insights into the role of surface oxygen defects in stabilizing V 2 O 5 with element doping. This research highlights the potential of multinonmetal doping to improve LIB cathode materials, offering a promising pathway for design of high-energy-density V 2 O 5 cathodes and advancing the development of next-generation energy storage solutions.

25 ENERGY STORAGE↗
DOE OSTI2025

Minimization of Cathode|Solid-Electrolyte Interfacial Delamination through the Application of Interphase Layers

Next-generation lithium-ion batteries are expected to use solid electrolytes (SEs) to enable higher energy density and extreme fast-charge capabilities. One major mode of degradation at the cathode|SE interface is delamination between the cathode active materials and SEs, which leads to performance decay. Experimental observations indicate that implementation of interphase layers can minimize the cathode|SE delamination induced capacity fade. A multiscale computational methodology is developed here to investigate the applicability of boron substituted lithium carbonate (Li 2+x B x C 1–x O 3 , x = 0.5, or LBCO) to minimize the delamination at the cathode|SE interface. Atomistic simulations indicate that the fracture energies at both the cathode|LBCO and LBCO|SE interfaces are higher than those at the cathode|SE interface, which reduces the extent of delamination. Mesoscale simulations indicate that, apart from increasing the fracture energy, decreasing the evolution of strain energy by lowering the elastic modulus of the interphase layer can also minimize the extent of delamination at the cathode|SE interface. However, the adoption of an interphase layer with high ionic conductivity is necessary to minimize the ohmic losses during operation at higher current densities. This study provides guidance on selecting interphase layers with specific properties and thicknesses to minimize both interfacial delamination and impedance growth.

LBCO↗
DOE OSTI2020

Amorphous Manganese Oxides: An Approach for Reversible Aqueous Zinc-Ion Batteries

Crystalline manganese oxides have attracted the most attention in aqueous zinc-ion batteries due to their diverse nanostructures and low cost. However, extensive studies on amorphous manganese oxides are lacking. Here in this paper, we report a mesoporous amorphous manganese oxide (UCT-1-250) as a cathode material with high capacity (222 mAh g –1 ), good cyclability (57% capacity retention after 200 cycles), and an acceptable discharge plateau (between 1.2 and 1.4 V). An approach to mechanistic studies was performed by comparison of UCT-1-250 and other crystalline manganese oxides through electrochemical, elemental, and structural analyses. An in situ conversion to ZnMn 2 O 4 spinel phase after initial cycling contributes to the high performance. The irreversible capacity fading is due to the formation of the woodruffite phase.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Adhesive Polymers as Efficient Binders for High-Capacity Silicon Electrodes

The major cause for capacity fading of silicon nanoparticle (SiNP)-based electrodes is the immense pressure applied toward the conductive networks during the charge/discharge process. While numerous efforts have been devoted to investigating different types of polymer binders, the rational design of an adhesive binder with pressure sensitivity has rarely been reported. Herein, a series of pressure-sensitive adhesives (PSAs) synthesized via copolymerization of 2-ethylhexyl acrylate (2-EHA) and acrylic acid (AA) are evaluated as polymer binders for SiNP-based electrodes. The balance between the density of interaction groups and viscoelastic properties is systematically investigated for efficient binding performance. The SiNP-based electrode using PSA with 20 mol % of 2-EHA (Si-PSA-20%) exhibits excellent electrochemical performance, achieving a capacity retention of 83% at the 100th cycle compared with 54% for Si-PAA after activation. Si-PSA-20% also delivers a superior cycling performance at a high current density (1731 mAh g –1 after 350 cycles vs 719 mAh g –1 after 150 cycles for Si-PAA, 1.8 A g –1 ) and at high mass loading of active materials (capacity retention of 74 vs 38% for Si-PAA after 100 cycles, SiNP content ~1.2 mg cm –2 ). Atomic force microscopy (AFM), peel tests, and Car–Parrinello molecular dynamics (CPMD) simulations are employed to understand their binder performance. The novel design and systematical investigation of PSAs as binders will definitely be appealing for not only the Si electrode but also for other high-energy-density electrode materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Molecular Design of a Highly Stable Single-Ion Conducting Polymer Gel Electrolyte

Single-ion conducting (SIC) polymer electrolytes with a high Li transference number ( t Li + ) have shown the capability to enable enhanced battery performance and safety by avoiding liquid–electrolyte leakage and suppressing Li dendrite formation. However, issues of insufficient ionic conductivity, low electrochemical stability, and poor polymer/electrode interfacial contact have greatly hindered their commercial use. In this work, a Li-containing boron-centered fluorinated SIC polymer gel electrolyte (LiBFSIE) was rationally designed to achieve a high t Li + and high electrochemical stability. Owing to the low dissociation energy of the boron-centered anion and Li + , the as-prepared LiBFSIE exhibited an ionic conductivity of 2 × 10 –4 S/cm at 35 °C, which is exclusively contributed by Li ions owing to a high t Li + of 0.93. Both simulation and experimental approaches were applied to investigate the ion diffusion and concentration gradient in the LiBFSIE and non-cross-linked dual-ion systems. Typical rectangular Li stripping/plating voltage profiles demonstrated the uniform Li deposition assisted by LiBFSIE. The interfacial contact and electrolyte infiltration were further optimized with an in situ UV–vis-initiated polymerization method together with the electrode materials. By virtue of the high electrochemical stability of LiBFSIE, the cells achieved a promising average Coulombic efficiency of 99.95% over 200 cycles, which is higher than that of liquid–electrolyte-based cells. No obvious capacity fading was observed, indicating the long-term stability of LiBFSIE for lithium metal batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tuning Irreversible Magnetoresistance in Pr 0.67 Sr 0.33 MnO 3 Film via Octahedral Rotation

Herein, the oxygen octahedral rotation around the out-of-plane axis is explored to study its effect on metastable status, magnetic cluster glass in manganite. The antiphase rotation around the out-of-plane axis (TiO 6 α Ο α Ο c – ) of SrTiO 3 enhances the Mn–O bond anisotropy along in-plane and out-of-plane directions and weakens the ferromagnetic interactions in a 12 nm Pr 0.67 Sr 0.33 MnO 3 film on the (001) SrTiO 3 substrate, which together promote the formation of magnetic cluster-glassiness and enlarges the irreversible magnetoresistance (MR) effect with enhanced relaxation time of charge carriers. The effect of TiO 6 α Ο α Ο c – in the SrTiO 3 substrate on material properties is obvious with a large irreversible MR effect for thin films, which fades away with the increase in film thickness. At 10 K, the irreversible MR is 0.91 for the 12 nm film and 0.22 for the 30 nm film. This work extends current understanding on interfacial coupling to metastable status and could help explore other systems in the perovskite structure with octahedral rotation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗