Search NASA⌕ Search

SEARCH · Search NASA

Results for “Flow fields”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Flow-field investigation of a supercruise fighter model

A NASA Langley investigation was conducted in the 16-foot Transonic Tunnel to survey the flow field around a model of a Supersonic cruise fighter configuration. In this investigation, a model of a supersonic cruise fighter configuration formerly utilized in afterbody-nozzle performance investigations was surveyed with a single, multiholed probe to determine local values of angle of attack, side flow, and Mach number. The investigation was conducted at Mach numbers of 0.6, 0.9, and 1.2 at angles of attack from 0 to 10 deg. The purpose of the investigation was to provide a data base of experimental data for use in verification of theoretical methods, and to compare the experimental data with predictions from currently available theoretical techniques. Results from this investigation show that local angles of attack were generally greater than free stream above the wing and generally less than free stream below the wing. Also there were large spanwise gradients above the wing at the higher angles of attack. The comparisons of experimental data with theoretical predictions show that the theoretical techniques give a qualitative estimate of the flow-field but will require much work to give good quantitative results.

Reubush, D. E.↗
NASA NTRS1969

Flow field simulation Patent

Wind tunnel method for simulating flow fields around blunt vehicles entering planetary atmospheres without involving high temperatures

Jones, R. A.↗
NASA NTRS1982

Three sensor hot wire/film technique for three dimensional mean and turbulence flow field measurement

Methods of measuring the three dimensional flow field using a three-sensor, hot-wire probe is described in this paper, with emphasis on the techniques developed by the author's group at The Pennsylvania State University. The hot wire equations, data processing procedure, calibration techniques, and a discussion of various errors in the measurement are included. Some typical data acquired by this probe is also included.

Lakshminarayana, B.↗
NASA NTRS1988

Digital enhancement of flow field images

Most photographs of experimentally generated fluid flow fields have inherently poor photographic quality, specifically low contrast. Thus, there is a need to establish a process for quickly and accurately enhancing these photographs to provide improved versions for physical interpretation, analysis, and publication. A sequence of digital image processing techniques which have been demonstrated to effectively enhance such photographs is described.

Kudlinski, Robert A.↗
NASA NTRS2003

Simulation of the Flow Field Associated with a Rocket Thruster Having an Attached Panel

Two-dimensional inviscid and viscous numerical simulations are performed to predict the flow field induced by a H2-O2 rocket thruster and to provide insight into the heat load on the articles placed in the hot gas exhaust of the thruster under a variety of operating conditions, using the National Combustion Code (NCC). The simulations have captured physical details of the flow field, such as the plume formation and expansion, formation of the shock waves and their effects on the temperature and pressure distributions on the walls of the apparatus and the flat panel. Comparison between the computed results for 2-D and adiabatic walls and the related experimental measurements for 3-D and cooled walls shows that the results of the simulations are consistent with those obtained from the related rig tests.

Davoudzadeh, Farhad↗
NASA NTRS1979

Effects of geometric and flow-field variables on inverted-velocity-profile coaxial jet noise and source distributions

This paper presents relationships between the noise generation characteristics and the flow-field characteristics for inverted-velocity-profile coaxial jets. Noise measurements were made at four different sideline distances in order to determine the apparent noise source locations, and flow-field characteristics were determined from jet plume pressure/temperature surveys. These relationships are based on a published NASA Lewis prediction model, the basic assumptions of which are shown to be consistent with the experimental data reported herein. Improvements to the noise prediction procedure, on the basis of the present study, are included, which increase the accuracy of the high-frequency noise prediction.

Stone, J. R.↗
NASA NTRS1953

Influence of End Plates on Lift and Flow Field of a Canard-type Control Surface at a Mach Number of 2.00

The influence of triangular-shaped end plates on the lift and the flow field of a canard-type control surface mounted on a symmetrical fuselage was investigated in the Lewis 8- by 6-foot supersonic wind tunnel at a Mach number of 2.00, body angle of attack of 2 degrees, and control-surface deflection angles of 3 degrees, 6 degrees, 8 degrees, and 10 degrees. The investigation demonstrated that the addition of end plates to a canard-type control surface increased its lift and rearranged the single vortex into a two-vortex system. Perforating the end plates reduced these effects and resulted in a decrease in lift and a change in the flow-field characteristics.

DIHEDRAL - COMPLETE WINGS↗
NASA NTRS1987

Laser velocimetry in turbulent flow fields - Particle response

Measurements of the particle response in a decelerating flow and a highly turbulent two-phase flow were obtained. Simultaneous measurements of the particle size and velocity served to quantify the particle response to the prevailing flow field. In the case of a flow incident upon a cylinder, the particle lag for a range of size classes was recorded. Results were also obtained in the flow generated by an atomizer operating on the leeward side of a flat disk bluff body in a coflowing air stream. Measurements of the mean axial, mean radial, and rms velocities and angles of trajectories were obtained for representative particle size classes. The air velocity and turbulence intensity were inferred from the seed particles on the order of one micrometer in diameter. Particles 9 micrometers and larger showed significant differences with respect to the gas phase mean velocity and turbulence intensity even at low velocities. In two-phase flows, reliable measurements of the continuous phase velocity and turbulence parameters requires the simultaneous measurement of particle size as a means for rejecting readings from large particles from the velocity pdf's.

Bachalo, W. D.↗
NASA NTRS1961

An Investigation of Transonic Flow Fields Surrounding Hot and Cold Sonic Jets

An investigation at free-stream Mach numbers of 0.90 t o 1.10 was made to determine (1) the jet boundaries and the flow fields around hot and cold jets, and (2) whether a cold-gas jet could adequately simulate the boundary and flow field of hot-gas jet. Schlieren photographs and static-pressure surveys were taken in the vacinity of a sonic jet which was operated over a range of jet pressure ratios of 1 to 6, specific heat ratios at the nozzle exit of 1.29 and 1.40, and jet temperatures up to 2600 R.

Lee, George↗
NASA NTRS1993

Characterization of cavity flow fields using pressure data obtained in the Langley 0.3-Meter Transonic Cryogenic Tunnel

Static and fluctuating pressure distributions were obtained along the floor of a rectangular-box cavity in an experiment performed in the LaRC 0.3-Meter Transonic Cryogenic Tunnel. The cavity studied was 11.25 in. long and 2.50 in. wide with a variable height to obtain length-to-height ratios of 4.4, 6.7, 12.67, and 20.0. The data presented herein were obtained for yaw angles of 0 deg and 15 deg over a Mach number range from 0.2 to 0.9 at a Reynolds number of 30 x 10(exp 6) per ft with a boundary-layer thickness of approximately 0.5 in. The results indicated that open and transitional-open cavity flow supports tone generation at subsonic and transonic speeds at Mach numbers of 0.6 and above. Further, pressure fluctuations associated with acoustic tone generation can be sustained when static pressure distributions indicate that transitional-closed and closed flow fields exist in the cavity. Cavities that support tone generation at 0 deg yaw also supported tone generation at 15 deg yaw when the flow became transitional-closed. For the latter cases, a reduction in tone amplitude was observed. Both static and fluctuating pressure data must be considered when defining cavity flow fields, and the flow models need to be refined to accommodate steady and unsteady flows.

Tracy, M. B.↗
NASA NTRS1990

Application of CFD to sonic boom near and mid flow-field prediction

A 3-D parabolized Navier-Stokes (PNS) code was used to calculate the supersonic overpressures from three different geometries at near- and mid-flow fields. Wind tunnel data is used for code validation. Comparison of the computed results with different grid refinements is shown. It is observed that a large number of grid points is needed to resolve the tail shock/expansion fan interaction. Therefore, an adaptive grid approach is employed to calculate the flow field. The agreement between the numerical results and the wind tunnel data confirms that computational fluid dynamics can be applied to the problem of sonic boom prediction.

Cheung, Samson H.↗
NASA NTRS1972

Analysis and design of three dimensional supersonic nozzles. Volume 2: Numerical program for analysis of nozzle-exhaust flow fields

The FORTRAN IV Program developed to analyze the flow field associated with scramjet exhaust systems is presented. The instructions for preparing input and interpreting output are described. The program analyzes steady three dimensional supersonic flow by the reference plane characteristic technique. The governing equations and numerical techniques employed are presented in Volume 1 of this report.

Kalben, P.↗
NASA NTRS1995

Exhausted Plume Flow Field Prediction Near the Afterbody of Hypersonic Flight Vehicles in High Altitudes

A two-dimensional computer code to solve the Burnett equations has been developed which computes the flow interaction between an exhausted plume and hypersonic external flow near the afterbody of a flight vehicle. This Burnett-2D code extends the capability of Navier-Stokes solver (RPLUS2D code) to include high-order Burnett source terms and slip-wall conditions for velocity and temperature. Higher-order Burnett viscous stress and heat flux terms are discretized using central-differencing and treated as source terms. Blocking logic is adopted in order to overcome the difficulty of grid generation. The computation of exhaust plume flow field is divided into two steps. In the first step, the thruster nozzle exit conditions are computed which generates inflow conditions in the base area near the afterbody. Results demonstrated that at high altitudes, the computations of nozzle exit conditions must include the effects of base flow since significant expansion exists in the base region. In the second step, Burnett equations were solved for exhaust plume flow field near the afterbody. The free stream conditions are set at an altitude equal to 80km and the Mach number is equal to 5.0. The preliminary results show that the plume expansion, as altitude increases, will eventually cause upstream flow separation.

Chou, Lynn Chen↗