Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel Cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Degradation of Fuel Cell Membrane Electrode Assemblies from Buses Operated More than 25,000 h

This study investigates the performance losses and degradation of proton-exchange-membrane fuel-cell stacks taken from the Alameda Contra Costa Transit District (AC Transit) bus system (Alameda and Contra Costa counties, California, United States) that were operated for over 25,000 h. Here, we focus on the origin of differences in electrochemical performance between beginning-of-life (BOL) and end-of-life states as well as diagnostic data acquired during the lifetime of the buses. In doing so, we employ in- and ex- situ characterization methods such as polarization curves, electrochemical impedance spectroscopy, electron microscopy, and X-ray characterization. Uniform degradation of the catalyst layer including Pt agglomeration/migration and electrode thinning was observed in all of the post-teardown measurements compared to BOL materials resulting from years of field operation. Despite these changes, the measured post-teardown performance suggests a sufficient output for the expected load, which indicate factors other than degradation of the membrane-electrode assemblies (MEAs) are likely responsible for the decommissioning of the stacks. The findings indicate that these MEA materials can enable long lifetime in fuel-cell vehicles, if the MEAs are not subjected to adverse operating conditions. The results also highlight the need for more in-vehicle diagnostics to maximize the lifetime of fuel cell vehicle (FCV) powerplants.

25 ENERGY STORAGE↗

Effect of non-solvent from the phase inversion method on the morphology and performance of the anode supported microtubular solid oxide fuel cells

The microstructure of the anode in anode-supported solid oxide fuel cells has significant influence on the cell performance. Here, microtubular Ni-yttria stabilized zircona (Zr 0.8 Y 0.2 O 2 , YSZ) anode support has been prepared by the phase inversion method. Different compositions of non-solvent have been used for the fabrication of the Ni-YSZ anode support, and the correlation between non-solvent composition and characteristics of the microstructure of the anode support has been investigated. The presence of ethanol or isopropanol in the non-solvent can inhibit the growth of the finger-like pores in the anode support. With the increase of the concentration of ethanol or isopropanol in the non-solvent, a thin dense layer can be observed on the top of the prepared tubular anode support. In addition, the mechanism of pore formation is explained based on the inter-diffusivity between the solvent and the non-solvent. Lastly, the prepared microtubular solid oxide fuel cells (MT-SOFCs) have been tested, and the influence of the anode microstructure on the cell electrochemical performance is analyzed based on a polarization model.

36 MATERIALS SCIENCE↗

Adsorption-Engineered Hydrocarbon Ionomers for Durable Proton-Exchange Membrane Fuel Cells

Reducing reliance on perfluoroalkyl substances (PFAS) in proton-exchange membrane fuel cells requires hydrocarbon ionomers that combine high performance with long-term durability, a persistent challenge in catalyst-layer design. Here, we identify oxidation-driven ionomer-catalyst interfacial degradation as a dominant failure pathway in hydrocarbon ionomer-bonded cathodes and introduce an adsorption-engineering strategy to overcome this limitation. The comparison of a commercial sulfonated poly(phenylene) (Pemion) with structurally engineered sulfonated poly(fluorene)s demonstrated that electrode durability is governed by the interplay between ionomer adsorption strength and resistance to oxidative degradation on carbon-supported Pt catalysts. A poly(fluorene) ionomer with mobile alkyl sulfonic acid groups forms resilient interfaces, delivering 1.28 A cm−2 at 0.65 V under fully humidified H2/air conditions (80°C and 150 kPaabs), comparable to Pemion. After 90,000 accelerated potential cycles, the poly(fluorene)-bonded cathode exhibits significantly improved durability, with only 29% performance loss compared to 58% for Pemion; further molecular refinement reduces the loss to 17%, approaching that of Nafion-bonded cathodes (14%). These findings establish adsorption-engineered ionomer design that decouples interfacial anchoring from oxidative degradation as a general strategy for achieving durable, high-performance PFAS-free PEM fuel cell electrodes.

08 HYDROGEN↗

Phenyl‐Free Polynorbornenes for Potential Anion Exchange Ionomers for Fuel Cells and Electrolyzers

Abstract Ionomers in the catalyst layer play a critical role in the performance of fuel cells and electrolyzers. Phenyl adsorption on hydrogen oxidation catalysts and electrochemical oxidation of phenyl moieties on oxygen evolution catalysts are detrimental to the alkaline devices’ performance. Here the adsorption energy of phenyl‐containing ionomers is compared to provide the rationale for implementing phenyl‐free ionomers. Density functional theory calculations indicated that the norbornane fragment has minimal adsorption energy on Pt(111) due to the absence of aromatic π electrons. A soluble quaternized polynorbornene ionomer is prepared by vinyl addition polymerization, and it exhibits high performance in both fuel cells and electrolyzers, proving the advantage of the phenyl‐free structure. This study establishes the phenyl adsorption energy‐electrode performance relationship, highlighting the importance of material interactions between the catalysts and ionomers.

25 ENERGY STORAGE↗

Operando X-ray absorption spectroscopic investigation of electrocatalysts state in anion exchange membrane fuel cells

Capturing the active state of (electro)catalysts under operating conditions, namely operando, is the ultimate objective of (electro)catalyst characterization, enabling the unraveling of reaction mechanisms and advancing (electro)catalyst development. Operando insights advance our understanding of the correlations between electrochemical tests and device-level performances. However, operando characterization of electrocatalysts is challenging due to the complexity of electrochemical devices and instrumental limitations. As a result, the majority of electrocatalyst characterizations have been limited to half-cell in situ studies. Here, we present an operando X-ray absorption spectroscopic study of Mn spinel oxide electrocatalysts in an operating fuel cell employing a custom-designed cell. Our results reveal that in anion exchange membrane fuel cells, the Mn valence state, within spinel Mn 3 O 4 /C, increases to above 3+, adopting an octahedral coordination devoid of Jahn-Teller distortions. This structural change results in an AEMFC performance equivalent to that of Co 1.5 Mn 1.5 O 4 /C, a composition that outperforms Mn 3 O 4 /C in rotating disk electrode tests. Our results underscore the importance of operando characterizations in elucidating the active state of electrocatalysts and understanding the correlation(s) between electrochemical tests and device performance.

Electrocatalysis↗

Probing Anion Exchange Membrane Fuel Cell Cathodes by Varying Electrocatalysts and Electrode Processing

To date, several high-performing anion exchange membrane fuel cells (AEMFCs) have been demonstrated, but most these studies have focused on Pt containing cathodes with high loadings. Here, we explore and compare the performance and perform electrochemical diagnostics on three leading AEMFC cathode electrocatalysts: Pt/C, Ag/C, and Fe–N–C with electrodes that have been processed with either powder or dispersion-based ionomers using perfluorinated anion exchange polymers. Pt/C had the highest performance but also showed a strong dependence on ionomer type, with powder ionomer exhibiting much higher performance. These results were consistent with the observations for Ag/C but did not hold for the Fe–N–C catalyst where almost no change was observed between powder and dispersion-based ionomers. This is the first-time the impact of powder and dispersion ionomer with different classes of cathode electrocatalysts on the fuel cell performance have been compared, and the results have strong implications for the ability to achieve high performance at low loadings and for better understanding catalyst-ionomer interactions within AEMFCs.

30 DIRECT ENERGY CONVERSION↗

Machine Learning Tools Set for Natural Gas Fuel Cell System Design

This study is focusing on leveraging the system design tools set for the next-generation solid oxide fuel cell (SOFC) based natural gas fuel cell (NGFC) system. Conventionally, system design and optimization of NGFC systems rely heavily on traditional reduced order model (ROM) techniques and designers’ experience level. For overcoming the technical barriers of system design, multiple multi-physics models and machine learning (ML) tools have been utilized to automate the conceptual design process and enhance the reliability of solutions for the NGFC system. The proposed tools set includes a physics-informed ML tool for automated ROM construction that leverages advances in deep neural networks to significantly reduce ROM prediction error for the NGFC power island compared to traditional approaches. The constructed physics-informed ML ROM can be used in system design, and optimization tools set Institute for the Design of Advanced Energy Systems (IDAES) Process Systems Engineering (PSE) framework. The tools set also provides a user-friendly graphic user interface built within Jupyter Notebooks, and the complete tools set is open-source public available.

Wang, Dewei↗

Slot-die-coating operability windows for polymer electrolyte membrane fuel cell cathode catalyst layers

Roll-to-roll (R2R) slot-die coating of polymer electrolyte membrane fuel cell (PEMFC) catalyst layers represents a scalable deposition method for producing 10–20 m 2 ·min -1 of catalyst-coated gas diffusion layers (GDLs). This high-throughput production technique will help lower the cost of PEMFC catalyst layers. The uniformity of the wet layer applied by slot die deposition is affected by process parameters such as substrate speed, vacuum pressure applied at the upstream meniscus, gap between the slot die lips and substrate, ink rheology, and other ink and substrate properties. The set of conditions for producing a defect-free coating with a dilute ink typically requires little to no upstream vacuum pressure, so suitable operating conditions can be found easily through trial and error and operator intuition. However, the higher viscosity of more concentrated inks dramatically shifts the range of settings that result in a homogeneous coating to higher vacuum levels, which are harder to find through hit or miss. A predictive model showing the range of operable conditions decreases material wastage inherent in experimentally searching for suitable parameters. In this study, the defect-free coating parameter window is explored experimentally and theoretically for two concentrations of PEFC cathode inks. Both a full capillary hydrodynamic model and a computationally cheaper viscocapillary model successfully predict the experimentally determined coating window within the experimental and model uncertainty limits for inks with 5.3 wt% and 12.0 wt% solids ink while maintaining the 0.1 mg Pt ·cm -2 Pt areal loading target. Here, this paper demonstrates a viable pathway for meeting the $30/kW net ultimate cost target of the United States Department of Energy (U.S. DOE) Hydrogen Fuel Cells Technologies Office (HFTO). The concentrated ink lowers the thermal energy and capital expenditure (CapEx) budget of the coating process by decreasing the amount of time, energy, and floorspace required for drying the coating.

25 ENERGY STORAGE↗

Improved cell performance and sulphur tolerance using A-site substituted Sr2Fe1.4Ni0.1Mo0.5O6–δ anodes for solid-oxide fuel cells

Abstract Solid-oxide fuel cells (SOFCs) offer great promise for producing electricity using a wide variety of fuels such as natural gas, coal gas and gasified carbonaceous solids; however, conventional nickel-based anodes face great challenges due to contaminants in readily available fuels, especially sulphur-containing compounds. Thus, the development of new anode materials that can suppress sulphur poisoning is crucial to the realization of fuel-flexible and cost-effective SOFCs. In this work, La0.1Sr1.9Fe1.4Ni0.1Mo0.5O6–δ (LSFNM) and Pr0.1Sr1.9Fe1.4Ni0.1Mo0.5O6–δ (PSFNM) materials have been synthesized using a sol-gel method in air and investigated as anode materials for SOFCs. Metallic nanoparticle-decorated ceramic anodes were obtained by the reduction of LSFNM and PSFNM in H2 at 850°C, forming a Ruddlesden–Popper oxide with exsolved FeNi3 bimetallic nanoparticles. The electrochemical performance of the Sr2Fe1.4Ni0.1Mo0.5O6–δ ceramic anode was greatly enhanced by La doping of A-sites, resulting in a 44% decrease in the polarization resistance in reducing atmosphere. The maximum power densities of Sr- and Mg-doped LaGaO3 (LSGM) (300 μm) electrolyte-supported single cells with LSFNM as the anode reached 1.371 W cm −2 in H2 and 1.306 W cm–2 in 50 ppm H2S–H2 at 850°C. Meanwhile, PSFNM showed improved sulphur tolerance, which could be fully recovered after six cycles from H2 to 50 ppm H2S–H2 operation. This study indicates that LSFNM and PSFNM are promising high-performance anodes for SOFCs.

Li, Haixia↗

Durable hybrid electrocatalysts for proton exchange membrane fuel cells

The low durability of carbon-based non-precious metal electrocatalysts hinders their practical applications in proton exchange membrane fuel cells (PEMFCs). In this study, we rationally design a hybrid Pt-Fe-N-C electrocatalyst with unprecedented durability. It consists of abundant Pt and Fe single atoms homogeneously dispersed on the nitrogen-doped carbon support and a small amount of Pt-Fe alloy nanoparticles. A PEMFC with Pt-Fe-N-C as the cathode shows a larger peak power density (0.75 W cm -2 ) than that with Fe-N-C as the cathode (0.50 W cm -2 ). The remarkable durability of Pt-Fe-N-C is reflected from no noticeable drop in the half-wave potential after 70000 potential cycles between 0.6 and 1.0 V in the liquid cell, and 80% current retention after 85 h of potential hold at 0.4 V in the fuel cell. This work demonstrates the feasibility of improving the durability of Fe-N-C material via ultra-low Pt doping and makes non-precious metal electrocatalysts be close to achieving commercial metrics.

25 ENERGY STORAGE↗

Techno-Economic Analysis of Natural Gas Fuel Cell Plant Configurations

The United States (U.S.) Department of Energy (DOE) Office of Fossil Energy and Carbon Management (FECM) and the National Energy Technology Laboratory (NETL) have been pursuing the development of solid oxide fuel cell (SOFC) technology to enable future power generation systems that are consistent with the cornerstones of the DOE mission—to ensure America’s security and prosperity by addressing its energy and environmental challenges through transformative science and technology solutions. The U.S. DOE FECM SOFC Program is currently focused on the development of low-cost, highly efficient, and reliable SOFC power systems. NETL’s SOFC technology development roadmap is aligned with near-term market opportunities in the distributed generation sector to validate and advance the technology while paving the way for utility-scale (> 50 MW) natural gas and coal-derived synthesis gas-fueled applications via progressively larger system demonstrations. The present study represents a part of a series of system evaluations being developed at NETL to aid in prioritizing technological advances along research pathways to the realization of utility-scale SOFC systems, a transformational goal of the fuel cell program. In particular, the system performance of utility-scale natural gas fuel cell (NGFC) systems with and without carbon dioxide (CO 2 ) capture is presented. The objective of the study is to provide targeted research and development (R&D) guidance to the FECM SOFC Program and SOFC commercial developers to accelerate technology deployment.

03 NATURAL GAS↗

Orange County Transportation Authority Fuel Cell Electric Bus Progress Report (Feb-Jul 2020) [Slides]

This report presents early results from a deployment of fuel cell electric buses (FCEBs) operated by Orange County Transportation Authority (OCTA) in Southern California. The ten FCEBs, produced by New Flyer, feature an electric drive propulsion system powered by a Ballard fuel cell system. The project team is collaborating with the U.S. Department of Energy (DOE) and DOE's National Renewable Energy Laboratory (NREL) to evaluate the buses in revenue service. The goal of this evaluation is to compare the FCEB performance to that of conventional technology and to track progress over time toward meeting the technical targets set by DOE and the Department of Transportation (DOT). The FCEBs were delivered beginning in late-2019, and were placed in service on February 9, 2020. The data period covers February 2020 through July 2020. NREL collects data on ten 2016 model year compressed natural gas (CNG) buses as a baseline comparison at OCTA.

33 ADVANCED PROPULSION SYSTEMS↗

Reinforced matrix for molten carbonate fuel cell and method for manufacturing the same

A reinforced electrolyte matrix for a molten carbonate fuel cell includes a porous ceramic matrix, a molten carbonate salt provided in the porous ceramic matrix, and at least one reinforcing structure comprised of at least one of yttrium, zirconium, cerium or oxides thereof. The reinforcing structure does not react with the molten carbonate salt. The reinforced electrolyte matrix separates a porous anode and a porous cathode in the molten carbonate fuel cell.

Surendranath, Arun↗

Electrocatalysis of Oxygen Reduction Reaction in a Polymer Electrolyte Fuel Cell with a Covalent Framework of Iron Phthalocyanine Aerogel

Carbon aerogels have been studied in the context of fuel cell electrodes mainly as catalyst support materials due to their high surface area, porosity, and electrical conductivity. Recently, aerogels composed solely of inorganic molecular complexes have shown to be promising materials for the electrocatalysis of oxygen reduction reaction (ORR). These aerogels consist of atomically dispersed catalytic sites. Herein, we report on the synthesis and characterization of an aerogel-based catalyst: iron phthalocyanine aerogel. It was synthesized by coupling of ethynyl-terminated phthalocyanine monomers and then heat-treated at 800 °C to increase its electrical conductivity and catalytic activity. Further, the aerogels reported here were tested as catalysts for ORR in acidic conditions for the first time and found to have a ultra-high number of atomically dispersed catalytic sites (7.11 × 10 20 sites g –1 ) and very good catalytic activity (E onset = 0.9 V vs RHE and TOF = 9.2 × 10 –3 e – s –1 site –1 at 0.8 V vs RHE). The iron phthalocyanine aerogel was also studied in a proton exchange membrane fuel cell, reaching a peak power density of 292 mW cm –2 and an open circuit voltage of 0.83 V.

25 ENERGY STORAGE↗

Core-Shell Heterostructures as Functional Materials for Solid Oxide Fuel Cell (SOFC) Electrodes

The principal objective of this project was to synthesize core-shell heterostructures for solid oxide fuel cell cathodes using a molten salt solvent. In doing so, the main goals were split into a) to elucidate and understand the influence of molten salt chemistries to expeditiously synthesize perovskite type oxides for solid oxide fuel cells, b) provide a chemical framework for future molten salt syntheses of energy relevant ceramic materials, c) demonstrate and investigate the required parameters for the optimal core-shell synthesis and yield of La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 (LSCF) – La 0.8 Sr 0.2 MnO 3 (shell), and d) demonstrate improved cathode performance of core-shell LSCF-LSM compared to an LSCF cathode on symmetric cells. The results clearly show that a) the influence of the molten salt cation outweighs the anion in regards to product stoichiometry, b) molten salts should be tailored to balance cationic and anionic acidity for high product yield, c) high yield of core-shell nanoparticles can be achieved by optimal mass ratio between core to shell, dwell time in the salt, size ratio between core to shell, and mass ratio between overall powder to salt, and d) the core-shell LSCF-LSM cathodes have lower polarization resistances than LSCF at higher temperatures. More work is required to optimize core-shell cathode performance at lower temperatures. However, this work thus provided justification for using the molten salt synthesis for SOFC cathodes and provided insights into future material modifications for improved performance.

08 HYDROGEN↗

Hydrogen Fuel Cell Electric Bus (FCEB) Evaluations in US Public Transit Service

The National Renewable Energy Laboratory (NREL) is a Department of Energy (DOE) national laboratory focused on renewable energy and energy efficiency. NREL has evaluated alternative fuel and advanced propulsion transit buses for DOE and the U.S. Department of Transportation's Federal Transit Administration (FTA). These evaluations are focused on determining the status of fuel cell systems and the corresponding infrastructure in transit applications to help DOE and FTA assess the progress toward technology readiness. For the last 19 years NREL has evaluated FCEBs in service around the United States and in Canada. The results of these evaluations have been published in numerous reports that compare FCEB performance to conventional technology as well as document the implementation experience and lessons learned by the transit agencies and their demonstration teams. Currently, 70 fuel cell buses are in active service in the US and 66 FCEBs are in development. NREL is evaluating a subset of the active FCEBs that includes three transit agencies demonstrating 25 fuel cell electric buses in California. One bus has exceeded 35,000 hours in service and 12 have exceeded 25,000 hours. Fuel economy for the current generation of FCEBs has improved 35% over the previous generation and is double that of conventional buses. Maintenance cost for FCEBs is equivalent to diesel and BEBs. The most up-to-date performance results will be presented, including fuel economy, availability, reliability, and operational costs.

bus↗

Migration and Precipitation of Platinum in Anion‐Exchange Membrane Fuel Cells

Abstract Despite the recent progress in increasing the power generation of Anion‐exchange membrane fuel cells (AEMFCs), their durability is still far lower than that of Proton exchange membrane fuel cells (PEMFCs). Using the complementary techniques of X‐ray micro‐computed tomography (CT), Scanning Electron Microscopy (SEM) and Energy Dispersive X‐ray (EDX) spectroscopy, we have identified Pt ion migration as an important factor to explain the decay in performance of AEMFCs. In alkaline media Pt +2 ions are easily formed which then either undergo dissolution into the carbon support or migrate to the membrane. In contrast to PEMFCs, where hydrogen cross over reduces the ions forming a vertical “Pt line” within the membrane, the ions in the AEM are trapped by charged groups within the membrane, leading to disintegration of the membrane and failure. Diffusion of the metal components is still observed when the Pt/C of the cathode is substituted with a FeCo−N−C catalyst, but in this case the Fe and Co ions are not trapped within the membrane, but rather migrate into the anode, thereby increasing the stability of the membrane.

Raut, Aniket↗